freebsd-dev/sys/dev/ath/if_ath_rx.h
Adrian Chadd c79f192c09 Begin plumbing ieee80211_rx_stats through the receive path.
Smart NICs with firmware (eg wpi, iwn, the new atheros parts, the intel 7260
series, etc) support doing a lot of things in firmware.  This includes but
isn't limited to things like scanning, sending probe requests and receiving
probe responses.  However, net80211 doesn't know about any of this - it still
drives the whole scan/probe infrastructure itself.

In order to move towards suppoting smart NICs, the receive path needs to
know about the channel/details for each received packet.  In at least
the iwn and 7260 firmware (and I believe wpi, but I haven't tried it yet)
it will do the scanning, power-save and off-channel buffering for you -
all you need to do is handle receiving beacons and probe responses on
channels that aren't what you're currently on.  However the whole receive
path is peppered with ic->ic_curchan and manual scan/powersave handling.
The beacon parsing code also checks ic->ic_curchan to determine if the
received beacon is on the correct channel or not.[1]

So:

* add freq/ieee values to ieee80211_rx_stats;
* change ieee80211_parse_beacon() to accept the 'current' channel
  as an argument;
* modify the iv_input() and iv_recv_mgmt() methods to include the rx_stats;
* add a new method - ieee80211_lookup_channel_rxstats() - that looks up
  a channel based on the contents of ieee80211_rx_stats;
* if it exists, use it in the mgmt path to switch the current channel
  (which still defaults to ic->ic_curchan) over to something determined
  by rx_stats.

This is enough to kick-start scan offload support in the Intel 7260
driver that Rui/I are working on.  It also is a good start for scan
offload support for a handful of existing NICs (wpi, iwn, some USB
parts) and it'll very likely dramatically improve stability/performance
there.  It's not the whole thing - notably, we don't need to do powersave,
we should not scan all channels, and we should leave probe request sending
to the firmware and not do it ourselves.  But, this allows for continued
development on the above features whilst actually having a somewhat
working NIC.

TODO:

* Finish tidying up how the net80211 input path works.
  Right now ieee80211_input / ieee80211_input_all act as the top-level
  that everything feeds into; it should change so the MIMO input routines
  are those and the legacy routines are phased out.

* The band selection should be done by the driver, not by the net80211
  layer.

* ieee80211_lookup_channel_rxstats() only determines 11b or 11g channels
  for now - this is enough for scanning, but not 100% true in all cases.
  If we ever need to handle off-channel scan support for things like
  static-40MHz or static-80MHz, or turbo-G, or half/quarter rates,
  then we should extend this.

[1] This is a side effect of frequency-hopping and CCK modes - you
    can receive beacons when you think you're on a different channel.
    In particular, CCK (which is used by the low 11b rates, eg beacons!)
    is decodable from adjacent channels - just at a low SNR.
    FH is a side effect of having the hardware/firmware do the frequency
    hopping - it may pick up beacons transmitted from other FH networks
    that are in a different phase of hopping frequencies.
2015-05-25 16:37:41 +00:00

67 lines
2.7 KiB
C

/*-
* Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
* redistribution must be conditioned upon including a substantially
* similar Disclaimer requirement for further binary redistribution.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
* AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
* THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
* OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
* IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGES.
*
* $FreeBSD$
*/
#ifndef __IF_ATH_RX_H__
#define __IF_ATH_RX_H__
extern u_int32_t ath_calcrxfilter(struct ath_softc *sc);
extern void ath_recv_mgmt(struct ieee80211_node *ni, struct mbuf *m,
int subtype, const struct ieee80211_rx_stats *rxs,
int rssi, int nf);
#define ath_stoprecv(_sc, _dodelay) \
(_sc)->sc_rx.recv_stop((_sc), (_dodelay))
#define ath_startrecv(_sc) \
(_sc)->sc_rx.recv_start((_sc))
#define ath_rx_flush(_sc) \
(_sc)->sc_rx.recv_flush((_sc))
#define ath_rxbuf_init(_sc, _bf) \
(_sc)->sc_rx.recv_rxbuf_init((_sc), (_bf))
#define ath_rxdma_setup(_sc) \
(_sc)->sc_rx.recv_setup(_sc)
#define ath_rxdma_teardown(_sc) \
(_sc)->sc_rx.recv_teardown(_sc)
#if 0
extern int ath_rxbuf_init(struct ath_softc *sc, struct ath_buf *bf);
extern void ath_rx_tasklet(void *arg, int npending);
extern void ath_rx_proc(struct ath_softc *sc, int resched);
extern void ath_stoprecv(struct ath_softc *sc, int dodelay);
extern int ath_startrecv(struct ath_softc *sc);
#endif
extern int ath_rx_pkt(struct ath_softc *sc, struct ath_rx_status *rs,
HAL_STATUS status, uint64_t tsf, int nf, HAL_RX_QUEUE qtype,
struct ath_buf *bf, struct mbuf *m);
extern void ath_recv_setup_legacy(struct ath_softc *sc);
#endif