freebsd-dev/sys/dev/vr/if_vrreg.h
Pyun YongHyeon de126af331 Teach vr(4) to use bus_dma(9) and major overhauling to handle link
state change and reliable error recovery.
 o Moved vr_softc structure and relevant macros to header file.
 o Use PCIR_BAR macro to get BARs.
 o Implemented suspend/resume methods.
 o Implemented automatic Tx threshold configuration which will be
   activated when it suffers from Tx underrun. Also Tx underrun
   will try to restart only Tx path and resort to previous
   full-reset(both Rx/Tx) operation if restarting Tx path have failed.
 o Removed old bit-banging MII interface. Rhine provides simple and
   efficient MII interface. While I'm here show PHY address and PHY
   register number when its read/write operation was failed.
 o Define VR_MII_TIMEOUT constant and use it in MII access routines.
 o Always honor link up/down state reported by mii layers. The link
   state information is used in vr_start() to determine whether we
   got a valid link.
 o Removed vr_setcfg() which is now handled in vr_link_task(), link
   state taskqueue handler. When mii layer reports link state changes
   the taskqueue handler reprograms MAC to reflect negotiated duplex
   settings. Flow-control changes are not handled yet and it should
   be revisited when mii layer knows the notion of flow-control.
 o Added a new sysctl interface to get statistics of an instance of
   the driver.(sysctl dev.vr.0.stats=1)
 o Chip name was renamed to reflect the official name of the chips
   described in VIA Rhine I/II/III datasheet.
	REV_ID_3065_A -> REV_ID_VT6102_A
	REV_ID_3065_B -> REV_ID_VT6102_B
	REV_ID_3065_C -> REV_ID_VT6102_C
	REV_ID_3106_J -> REV_ID_VT6105_A0
	REV_ID_3106_S -> REV_ID_VT6105M_A0
   The following chip revisions were added.
	#define REV_ID_VT6105_B0	0x83
	#define REV_ID_VT6105_LOM	0x8A
	#define REV_ID_VT6107_A0	0x8C
	#define REV_ID_VT6107_A1	0x8D
	#define REV_ID_VT6105M_B1	0x94
 o Always show chip revision number in device attach. This shall help
   identifying revision specific issues.
 o Check whether EEPROM reloading is complete by inspecting the state
   of VR_EECSR_LOAD bit. This bit is self-cleared after the EEPROM
   reloading. Previously vr(4) blindly spins for 200us which may/may
   not enough to complete the EEPROM reload.
 o Removed if_mtu setup. It's done in ether_ifattach().
 o Use our own callout to drive watchdog timer.
 o In vr_attach disable further interrupts after reset. For VT6102 or
   newer hardwares, diable MII state change interrupt as well because
   mii state handling is done by mii layer.
 o Add more sane register initialization for VT6102 or newer chips.
    - Have NIC report error instead of retrying forever.
    - Let hardware detect MII coding error.
    - Enable MODE10T mode.
    - Enable memory-read-multiple for VT6107.
 o PHY address for VT6105 or newer chips is located at fixed address 1.
   For older chips the PHY address is stored in VR_PHYADDR register.
   Armed with these information, there is no need to re-read
   VR_PHYADDR register in miibus handler to get PHY address. This
   saves one register access cycle for each MII access.
 o Don't reprogram VR_PHYADDR register whenever access to a register
   located at a PHY address is made. Rhine fmaily allows reprogramming
   PHY address location via VR_PHYADDR register depending on
   VR_MIISTAT_PHYOPT bit of VR_MIISTAT register. This used to lead
   numerous phantom PHYs attached to miibus during phy probe phase and
   driver used to limit allowable PHY address in mii register accessors
   for certain chip revisions. This removes one more register access
   cycle for each MII access.
 o Correctly set VLAN header length.
 o bus_dma(9) conversion.
    - Limit DMA access to be in range of 32bit address space. Hardware
      doesn't support DAC.
    - Apply descriptor ring alignment requirements(16 bytes alignment)
    - Apply Rx buffer address alignment requirements(4 bytes alignment)
    - Apply Tx buffer address alignment requirements(4 bytes alignment)
      for Rhine I chip. Rhine II or III has no Tx buffer address
      alignment restrictions, though.
    - Reduce number of allowable number of DMA segments to 8.
    - Removed the atomic(9) used in descriptor ownership managements
      as it's job of bus_dmamap_sync(9).
    With these change vr(4) should work on all platforms.
 o Rhine uses two separated 8bits command registers to control Tx/Rx
   MAC. So don't access it as a single 16bit register.
 o For non-strict alignment architectures vr(4) no longer require
   time-consuming copy operation for received frames to align IP
   header. This greatly improves Rx performance on i386/amd64
   platforms. However the alignment is still necessary for
   strict-alignment platforms(e.g. sparc64). The alignment is handled
   in new fuction vr_fixup_rx().
 o vr_rxeof() now rejects multiple-segmented(fragmented) frames as
   vr(4) is not ready to handle this situation. Datasheet said nothing
   about the reason when/why it happens.
 o In vr_newbuf() don't set VR_RXSTAT_FIRSTFRAG/VR_RXSTAT_LASTFRAG
   bits as it's set by hardware.
 o Don't pass checksum offload information to upper layer for
   fragmented frames. The hardware assisted checksum is valid only
   when the frame is non-fragmented IP frames. Also mark the checksum
   is valid for corrupted frames such that upper layers doesn't need
   to recompute the checksum with software routine.
 o Removed vr_rxeoc(). RxDMA doesn't seem to need to be idle before
   sending VR_CMD_RX_GO command. Previously it used to stop RxDMA
   first which in turn resulted in long delays in Rx error recovery.
 o Rewrote Tx completion handler.
    - Always check VR_TXSTAT_OWN bit in status word prior to
      inspecting other status bits in the status word.
    - Collision counter updates were corrected as VT3071 or newer
      ones use different bits to notify collisions.
    - Unlike other chip revisions, VT86C100A uses different bit to
      indicate Tx underrun. For VT3071 or newer ones, check both
      VR_TXSTAT_TBUFF and VR_TXSTAT_UDF bits to see whether Tx
      underrun was happend. In case of Tx underrun requeue the failed
      frame and restart stalled Tx SM. Also double Tx DMA threshold
      size on each failure to mitigate future Tx underruns.
    - Disarm watchdog timer only if we have no queued packets,
      otherwise don't touch watchdog timer.
 o Rewrote interrupt handler.
    - status word in Tx/Rx descriptors indicates more detailed error
      state required to recover from the specific error. There is no
      need to rely on interrupt status word to recover from Tx/Rx
      error except PCI bus error. Other event notifications like
      statistics counter overflows or link state events will be
      handled in main interrupt handler.
    - Don't touch VR_IMR register if we are in suspend mode. Touching
      the register may hang the hardware if we are in suspended state.
      Previously it seems that touching VR_IMR register in interrupt
      handler was to work-around panic occurred in system shutdown
      stage on SMP systems. I think that work-around would hide
      root-cause of the panic and I couldn't reproduce the panic
      with multiple attempts on my box.
 o While padding space to meet minimum frame size, zero the pad data
   in order to avoid possibly leaking sensitive data.
 o Rewrote vr_start_locked().
    - Don't try to queue packets if number of available Tx descriptors
      are short than that of required one.
 o Don't reinitialize hardware whenever media configuration is
   changed. Media/link state changes are reported from mii layer if
   this happens and vr_link_task() will perform necessary changes.
 o Don't reinitialize hardware if only PROMISC bit was changed. Just
   toggle the PROMISC bit in hardware is sufficient to reflect the
   request.
 o Rearrganed the IFCAP_POLLING/IFCAP_HWCSUM handling in vr_ioctl().
 o Generate Tx completion interrupts for every VR_TX_INTR_THRESH-th
   frames. This reduces Tx completion interrupts under heavy network
   loads.
 o Since vr(4) doesn't request Tx interrupts for every queued frames,
   reclaim any pending descriptors not handled in Tx completion
   handler before actually firing up watchdog timeouts.
 o Added vr_tx_stop()/vr_rx_stop() to wait for the end of active
   TxDMA/RxDMA cycles(draining). These routines are used in vr_stop()
   to ensure sane state of MAC before releasing allocated Tx/Rx
   buffers. vr_link_task() also takes advantage of these functions to
   get to idle state prior to restarting Tx/Rx.
 o Added vr_tx_start()/vr_rx_start() to restart Rx/Tx. By separating
   Rx operation from Tx operation vr(4) no longer need to full-reset
   the hardware in case of Tx/Rx error recovery.
 o Implemented WOL.
 o Added VT6105M specific register definitions. VT6105M has the
   following hardware capabilities.
    - Tx/Rx IP/TCP/UDP checksum offload.
    - VLAN hardware tag insertion/extraction. Due to lack of information
       for getting extracted VLAN tag in Rx path, VLAN hardware support
       was not implemented yet.
    - CAM(Content Addressable Memory) based 32 entry perfect multicast/
      VLAN filtering.
    - 8 priority queues.
 o Implemented CAM based 32 entry perfect multicast filtering for
   VT6105M. If number of multicast entry is greater than 32, vr(4)
   uses traditional hash based filtering.
 o Reflect real Tx/Rx descriptor structure. Previously vr(4) used to
   embed other driver (private) data into these structure. This type
   of embedding make it hard to work on LP64 systems.
 o Removed unused vr_mii_frame structure and MII bit-baning
   definitions.
 o Added new PCI configuration registers that controls mii operation
   and mode selection.
 o Reduced number of Tx/Rx descriptors to 128 from 256. From my
   testing, increasing number of descriptors above than 64 didn't help
   increasing performance at all. Experimentations show 128 Rx
   descriptors seems to help a lot reducing Rx FIFO overruns under
   high system loads. It seems the poor Tx performance of Rhine
   hardwares comes from the limitation of hardware. You wouldn't
   satuarte the link with vr(4) no matter how fast CPU/large number of
   descriptors are used.
 o Added vr_statistics structure to hold various counter values.

No regression was reported but one variant of Rhine III(VT6105M)
found on RouterBOARD 44 does not work yet(Reported by Milan Obuch).
I hope this would be resolved in near future.

I'd like to say big thanks to Mike Tancsa who kindly donated a Rhine
hardware to me. Without his enthusiastic testing and feedbacks
overhauling vr(4) never have been possible. Also thanks to Masayuki
Murayama who provided some good comments on the hardware's internals.
This driver is result of combined effort of many users who provided
many feedbacks so I'd like to say special thanks to them.

Hardware donated by:	Mike Tancsa (mike AT sentex dot net)
Reviewed by:		remko (initial version)
Tested by:		Mike Tancsa(x86), JoaoBR ( joao AT matik DOT com DOT br )
			Marcin Wisnicki ( mwisnicki+freebsd AT gmail DOT com )
			Stefan Ehmann ( shoesoft AT gmx DOT net )
			Florian Smeets ( flo AT kasimir DOT com )
			Phil Oleson ( oz AT nixil DOT net )
			Larry Baird ( lab AT gta DOT com )
			Milan Obuch ( freebsd-current AT dino DOT sk )
			remko (initial version)
2008-03-11 04:51:22 +00:00

753 lines
21 KiB
C

/*-
* Copyright (c) 1997, 1998
* Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD$
*/
/*
* Rhine register definitions.
*/
#define VR_PAR0 0x00 /* node address 0 to 4 */
#define VR_PAR1 0x04 /* node address 2 to 6 */
#define VR_RXCFG 0x06 /* receiver config register */
#define VR_TXCFG 0x07 /* transmit config register */
#define VR_CR0 0x08 /* command register 0 */
#define VR_CR1 0x09 /* command register 1 */
#define VR_TQW 0x0A /* tx queue wake 6105M, 8bits */
#define VR_ISR 0x0C /* interrupt/status register */
#define VR_IMR 0x0E /* interrupt mask register */
#define VR_MAR0 0x10 /* multicast hash 0 */
#define VR_MAR1 0x14 /* multicast hash 1 */
#define VR_RXADDR 0x18 /* rx descriptor list start addr */
#define VR_TXADDR 0x1C /* tx descriptor list start addr */
#define VR_CURRXDESC0 0x20
#define VR_CURRXDESC1 0x24
#define VR_CURRXDESC2 0x28
#define VR_CURRXDESC3 0x2C
#define VR_NEXTRXDESC0 0x30
#define VR_NEXTRXDESC1 0x34
#define VR_NEXTRXDESC2 0x38
#define VR_NEXTRXDESC3 0x3C
#define VR_CURTXDESC0 0x40
#define VR_CURTXDESC1 0x44
#define VR_CURTXDESC2 0x48
#define VR_CURTXDESC3 0x4C
#define VR_NEXTTXDESC0 0x50
#define VR_NEXTTXDESC1 0x54
#define VR_NEXTTXDESC2 0x58
#define VR_NEXTTXDESC3 0x5C
#define VR_CURRXDMA 0x60 /* current RX DMA address */
#define VR_CURTXDMA 0x64 /* current TX DMA address */
#define VR_TALLYCNT 0x68 /* tally counter test register */
#define VR_PHYADDR 0x6C
#define VR_MIISTAT 0x6D
#define VR_BCR0 0x6E
#define VR_BCR1 0x6F
#define VR_MIICMD 0x70
#define VR_MIIADDR 0x71
#define VR_MIIDATA 0x72
#define VR_EECSR 0x74
#define VR_TEST 0x75
#define VR_GPIO 0x76
#define VR_CFGA 0x78
#define VR_CFGB 0x79
#define VR_CFGC 0x7A
#define VR_CFGD 0x7B
#define VR_MPA_CNT 0x7C
#define VR_CRC_CNT 0x7E
#define VR_MISC_CR0 0x80 /* VT6102, 8bits */
#define VR_MISC_CR1 0x81
#define VR_STICKHW 0x83
#define VR_MII_ISR 0x84
#define VR_MII_IMR 0x86
#define VR_CAMMASK 0x88 /* VT6105M, 32bits */
#define VR_CAMCTL 0x92 /* VT6105M, 8bits */
#define VR_CAMADDR 0x93 /* VT6105M, 8bits */
#define VR_FLOWCR0 0x98
#define VR_FLOWCR1 0x99
#define VR_PAUSETIMER 0x9A /* 16bit */
#define VR_WOLCR_SET 0xA0
#define VR_PWRCFG_SET 0xA1
#define VR_TESTREG_SET 0xA2
#define VR_WOLCFG_SET 0xA3
#define VR_WOLCR_CLR 0xA4
#define VR_PWRCFG_CLR 0xA5
#define VR_TESTREG_CLR 0xA6
#define VR_WOLCFG_CLR 0xA7
#define VR_PWRCSR_SET 0xA8
#define VR_PWRCSR1_SET 0xA9
#define VR_PWRCSR_CLR 0xAC
#define VR_PWRCSR1_CLR 0xAD
/* Misc Registers */
#define VR_MISCCR0_RXPAUSE 0x08
#define VR_MISCCR1_FORSRST 0x40
/*
* RX config bits.
*/
#define VR_RXCFG_RX_ERRPKTS 0x01
#define VR_RXCFG_RX_RUNT 0x02
#define VR_RXCFG_RX_MULTI 0x04
#define VR_RXCFG_RX_BROAD 0x08
#define VR_RXCFG_RX_PROMISC 0x10
#define VR_RXCFG_RX_THRESH 0xE0
#define VR_RXTHRESH_32BYTES 0x00
#define VR_RXTHRESH_64BYTES 0x20
#define VR_RXTHRESH_128BYTES 0x40
#define VR_RXTHRESH_256BYTES 0x60
#define VR_RXTHRESH_512BYTES 0x80
#define VR_RXTHRESH_768BYTES 0xA0
#define VR_RXTHRESH_1024BYTES 0xC0
#define VR_RXTHRESH_STORENFWD 0xE0
/*
* TX config bits.
*/
#define VR_TXCFG_TXTAGEN 0x01 /* 6105M */
#define VR_TXCFG_LOOPBKMODE 0x06
#define VR_TXCFG_BACKOFF 0x08
#define VR_TXCFG_RXTAGCTL 0x10 /* 6105M */
#define VR_TXCFG_TX_THRESH 0xE0
#define VR_TXTHRESH_32BYTES 0x00
#define VR_TXTHRESH_64BYTES 0x20
#define VR_TXTHRESH_128BYTES 0x40
#define VR_TXTHRESH_256BYTES 0x60
#define VR_TXTHRESH_512BYTES 0x80
#define VR_TXTHRESH_768BYTES 0xA0
#define VR_TXTHRESH_1024BYTES 0xC0
#define VR_TXTHRESH_STORENFWD 0xE0
#define VR_TXTHRESH_MIN 1 /* 64 bytes */
#define VR_TXTHRESH_MAX 5 /* store and forward */
/*
* Command register bits.
*/
#define VR_CR0_INIT 0x01
#define VR_CR0_START 0x02
#define VR_CR0_STOP 0x04
#define VR_CR0_RX_ON 0x08
#define VR_CR0_TX_ON 0x10
#define VR_CR0_TX_GO 0x20
#define VR_CR0_RX_GO 0x40
#define VR_CR0_RSVD 0x80
#define VR_CR1_RX_EARLY 0x01
#define VR_CR1_TX_EARLY 0x02
#define VR_CR1_FULLDUPLEX 0x04
#define VR_CR1_TX_NOPOLL 0x08
#define VR_CR1_RESET 0x80
/*
* Interrupt status bits.
*/
#define VR_ISR_RX_OK 0x0001 /* packet rx ok */
#define VR_ISR_TX_OK 0x0002 /* packet tx ok */
#define VR_ISR_RX_ERR 0x0004 /* packet rx with err */
#define VR_ISR_TX_ABRT 0x0008 /* tx aborted due to excess colls */
#define VR_ISR_TX_UNDERRUN 0x0010 /* tx buffer underflow */
#define VR_ISR_RX_NOBUF 0x0020 /* no rx buffer available */
#define VR_ISR_BUSERR 0x0040 /* PCI bus error */
#define VR_ISR_STATSOFLOW 0x0080 /* stats counter oflow */
#define VR_ISR_RX_EARLY 0x0100 /* rx early */
#define VR_ISR_LINKSTAT 0x0200 /* MII status change */
#define VR_ISR_ETI 0x0200 /* Tx early (3043/3071) */
#define VR_ISR_UDFI 0x0200 /* Tx FIFO underflow (6102) */
#define VR_ISR_RX_OFLOW 0x0400 /* rx FIFO overflow */
#define VR_ISR_RX_DROPPED 0x0800
#define VR_ISR_RX_NOBUF2 0x1000 /* Rx descriptor running up */
#define VR_ISR_TX_ABRT2 0x2000
#define VR_ISR_LINKSTAT2 0x4000
#define VR_ISR_MAGICPACKET 0x8000
#define VR_ISR_ERR_BITS "\20" \
"\3RXERR\4TXABRT\5TXUNDERRUN" \
"\6RXNOBUF\7BUSERR\10STATSOFLOW" \
"\12TXUDF\13RXOFLOW\14RXDROPPED" \
"\15RXNOBUF2\16TXABRT2"
/*
* Interrupt mask bits.
*/
#define VR_IMR_RX_OK 0x0001 /* packet rx ok */
#define VR_IMR_TX_OK 0x0002 /* packet tx ok */
#define VR_IMR_RX_ERR 0x0004 /* packet rx with err */
#define VR_IMR_TX_ABRT 0x0008 /* tx aborted due to excess colls */
#define VR_IMR_TX_UNDERRUN 0x0010 /* tx buffer underflow */
#define VR_IMR_RX_NOBUF 0x0020 /* no rx buffer available */
#define VR_IMR_BUSERR 0x0040 /* PCI bus error */
#define VR_IMR_STATSOFLOW 0x0080 /* stats counter oflow */
#define VR_IMR_RX_EARLY 0x0100 /* rx early */
#define VR_IMR_LINKSTAT 0x0200 /* MII status change */
#define VR_IMR_RX_OFLOW 0x0400 /* rx FIFO overflow */
#define VR_IMR_RX_DROPPED 0x0800
#define VR_IMR_RX_NOBUF2 0x1000
#define VR_IMR_TX_ABRT2 0x2000
#define VR_IMR_LINKSTAT2 0x4000
#define VR_IMR_MAGICPACKET 0x8000
#define VR_INTRS \
(VR_IMR_RX_OK|VR_IMR_TX_OK|VR_IMR_RX_NOBUF| \
VR_IMR_TX_ABRT|VR_IMR_TX_UNDERRUN|VR_IMR_BUSERR| \
VR_IMR_RX_ERR|VR_ISR_RX_DROPPED)
/*
* MII status register.
*/
#define VR_MIISTAT_SPEED 0x01
#define VR_MIISTAT_LINKFAULT 0x02
#define VR_MIISTAT_MGTREADERR 0x04
#define VR_MIISTAT_MIIERR 0x08
#define VR_MIISTAT_PHYOPT 0x10
#define VR_MIISTAT_MDC_SPEED 0x20
#define VR_MIISTAT_RSVD 0x40
#define VR_MIISTAT_GPIO1POLL 0x80
/*
* MII command register bits.
*/
#define VR_MIICMD_CLK 0x01
#define VR_MIICMD_DATAOUT 0x02
#define VR_MIICMD_DATAIN 0x04
#define VR_MIICMD_DIR 0x08
#define VR_MIICMD_DIRECTPGM 0x10
#define VR_MIICMD_WRITE_ENB 0x20
#define VR_MIICMD_READ_ENB 0x40
#define VR_MIICMD_AUTOPOLL 0x80
/*
* EEPROM control bits.
*/
#define VR_EECSR_DATAIN 0x01 /* data out */
#define VR_EECSR_DATAOUT 0x02 /* data in */
#define VR_EECSR_CLK 0x04 /* clock */
#define VR_EECSR_CS 0x08 /* chip select */
#define VR_EECSR_DPM 0x10
#define VR_EECSR_LOAD 0x20
#define VR_EECSR_EMBP 0x40
#define VR_EECSR_EEPR 0x80
#define VR_EECMD_WRITE 0x140
#define VR_EECMD_READ 0x180
#define VR_EECMD_ERASE 0x1c0
/*
* Test register bits.
*/
#define VR_TEST_TEST0 0x01
#define VR_TEST_TEST1 0x02
#define VR_TEST_TEST2 0x04
#define VR_TEST_TSTUD 0x08
#define VR_TEST_TSTOV 0x10
#define VR_TEST_BKOFF 0x20
#define VR_TEST_FCOL 0x40
#define VR_TEST_HBDES 0x80
/*
* Config A register bits.
*/
#define VR_CFG_GPIO2OUTENB 0x01
#define VR_CFG_GPIO2OUT 0x02 /* gen. purp. pin */
#define VR_CFG_GPIO2IN 0x04 /* gen. purp. pin */
#define VR_CFG_AUTOOPT 0x08 /* enable rx/tx autopoll */
#define VR_CFG_MIIOPT 0x10
#define VR_CFG_MMIENB 0x20 /* memory mapped mode enb */
#define VR_CFG_JUMPER 0x40 /* PHY and oper. mode select */
#define VR_CFG_EELOAD 0x80 /* enable EEPROM programming */
/*
* Config B register bits.
*/
#define VR_CFG_LATMENB 0x01 /* larency timer effect enb. */
#define VR_CFG_MRREADWAIT 0x02
#define VR_CFG_MRWRITEWAIT 0x04
#define VR_CFG_RX_ARB 0x08
#define VR_CFG_TX_ARB 0x10
#define VR_CFG_READMULTI 0x20
#define VR_CFG_TX_PACE 0x40
#define VR_CFG_TX_QDIS 0x80
/*
* Config C register bits.
*/
#define VR_CFG_ROMSEL0 0x01
#define VR_CFG_ROMSEL1 0x02
#define VR_CFG_ROMSEL2 0x04
#define VR_CFG_ROMTIMESEL 0x08
#define VR_CFG_RSVD0 0x10
#define VR_CFG_ROMDLY 0x20
#define VR_CFG_ROMOPT 0x40
#define VR_CFG_RSVD1 0x80
/*
* Config D register bits.
*/
#define VR_CFG_BACKOFFOPT 0x01
#define VR_CFG_BACKOFFMOD 0x02
#define VR_CFG_CAPEFFECT 0x04
#define VR_CFG_BACKOFFRAND 0x08
#define VR_CFG_MAGICKPACKET 0x10
#define VR_CFG_PCIREADLINE 0x20
#define VR_CFG_DIAG 0x40
#define VR_CFG_GPIOEN 0x80
/* Sticky HW bits */
#define VR_STICKHW_DS0 0x01
#define VR_STICKHW_DS1 0x02
#define VR_STICKHW_WOL_ENB 0x04
#define VR_STICKHW_WOL_STS 0x08
#define VR_STICKHW_LEGWOL_ENB 0x80
/*
* BCR0 register bits. (At least for the VT6102 chip.)
*/
#define VR_BCR0_DMA_LENGTH 0x07
#define VR_BCR0_DMA_32BYTES 0x00
#define VR_BCR0_DMA_64BYTES 0x01
#define VR_BCR0_DMA_128BYTES 0x02
#define VR_BCR0_DMA_256BYTES 0x03
#define VR_BCR0_DMA_512BYTES 0x04
#define VR_BCR0_DMA_1024BYTES 0x05
#define VR_BCR0_DMA_STORENFWD 0x07
#define VR_BCR0_RX_THRESH 0x38
#define VR_BCR0_RXTHRESHCFG 0x00
#define VR_BCR0_RXTHRESH64BYTES 0x08
#define VR_BCR0_RXTHRESH128BYTES 0x10
#define VR_BCR0_RXTHRESH256BYTES 0x18
#define VR_BCR0_RXTHRESH512BYTES 0x20
#define VR_BCR0_RXTHRESH1024BYTES 0x28
#define VR_BCR0_RXTHRESHSTORENFWD 0x38
#define VR_BCR0_EXTLED 0x40
#define VR_BCR0_MED2 0x80
/*
* BCR1 register bits. (At least for the VT6102 chip.)
*/
#define VR_BCR1_POT0 0x01
#define VR_BCR1_POT1 0x02
#define VR_BCR1_POT2 0x04
#define VR_BCR1_TX_THRESH 0x38
#define VR_BCR1_TXTHRESHCFG 0x00
#define VR_BCR1_TXTHRESH64BYTES 0x08
#define VR_BCR1_TXTHRESH128BYTES 0x10
#define VR_BCR1_TXTHRESH256BYTES 0x18
#define VR_BCR1_TXTHRESH512BYTES 0x20
#define VR_BCR1_TXTHRESH1024BYTES 0x28
#define VR_BCR1_TXTHRESHSTORENFWD 0x38
/*
* CAMCTL register bits. (VT6105M only)
*/
#define VR_CAMCTL_ENA 0x01
#define VR_CAMCTL_VLAN 0x02
#define VR_CAMCTL_MCAST 0x00
#define VR_CAMCTL_WRITE 0x04
#define VR_CAMCTL_READ 0x08
#define VR_CAM_MCAST_CNT 32
#define VR_CAM_VLAN_CNT 32
/*
* FLOWCR1 register bits. (VT6105LOM, VT6105M only)
*/
#define VR_FLOWCR1_TXLO4 0x00
#define VR_FLOWCR1_TXLO8 0x40
#define VR_FLOWCR1_TXLO16 0x80
#define VR_FLOWCR1_TXLO24 0xC0
#define VR_FLOWCR1_TXHI24 0x00
#define VR_FLOWCR1_TXHI32 0x10
#define VR_FLOWCR1_TXHI48 0x20
#define VR_FLOWCR1_TXHI64 0x30
#define VR_FLOWCR1_XONXOFF 0x08
#define VR_FLOWCR1_TXPAUSE 0x04
#define VR_FLOWCR1_RXPAUSE 0x02
#define VR_FLOWCR1_HDX 0x01
/*
* WOLCR register bits. (VT6102 or higher only)
*/
#define VR_WOLCR_PATTERN0 0x01
#define VR_WOLCR_PATTERN1 0x02
#define VR_WOLCR_PATTERN2 0x04
#define VR_WOLCR_PATTERN3 0x08
#define VR_WOLCR_UCAST 0x10
#define VR_WOLCR_MAGIC 0x20
#define VR_WOLCR_LINKON 0x40
#define VR_WOLCR_LINKOFF 0x80
/*
* PWRCFG register bits. (VT6102 or higher only)
*/
#define VR_PWRCFG_WOLEN 0x01
#define VR_PWRCFG_WOLSR 0x02
#define VR_PWRCFG_LEGACY_WOL 0x10
#define VR_PWRCFG_WOLTYPE_PULSE 0x20
#define VR_PWRCFG_SMIITIME 0x80
/*
* WOLCFG register bits. (VT6102 or higher only)
*/
#define VR_WOLCFG_PATTERN_PAGE 0x04 /* VT6505 B0 */
#define VR_WOLCFG_SMIIOPT 0x04
#define VR_WOLCFG_SMIIACC 0x08
#define VR_WOLCFG_SAB 0x10
#define VR_WOLCFG_SAM 0x20
#define VR_WOLCFG_SFDX 0x40
#define VR_WOLCFG_PMEOVR 0x80
/*
* Rhine TX/RX list structure.
*/
struct vr_desc {
uint32_t vr_status;
uint32_t vr_ctl;
uint32_t vr_data;
uint32_t vr_nextphys;
};
#define VR_RXSTAT_RXERR 0x00000001
#define VR_RXSTAT_CRCERR 0x00000002
#define VR_RXSTAT_FRAMEALIGNERR 0x00000004
#define VR_RXSTAT_FIFOOFLOW 0x00000008
#define VR_RXSTAT_GIANT 0x00000010
#define VR_RXSTAT_RUNT 0x00000020
#define VR_RXSTAT_BUSERR 0x00000040
#define VR_RXSTAT_FRAG 0x00000040 /* 6105M */
#define VR_RXSTAT_BUFFERR 0x00000080
#define VR_RXSTAT_LASTFRAG 0x00000100
#define VR_RXSTAT_FIRSTFRAG 0x00000200
#define VR_RXSTAT_RLINK 0x00000400
#define VR_RXSTAT_RX_PHYS 0x00000800
#define VR_RXSTAT_RX_BROAD 0x00001000
#define VR_RXSTAT_RX_MULTI 0x00002000
#define VR_RXSTAT_RX_OK 0x00004000
#define VR_RXSTAT_RXLEN 0x07FF0000
#define VR_RXSTAT_RXLEN_EXT 0x78000000
#define VR_RXSTAT_OWN 0x80000000
#define VR_RXBYTES(x) ((x & VR_RXSTAT_RXLEN) >> 16)
#define VR_RXSTAT_ERR_BITS "\20" \
"\1RXERR\2CRCERR\3FRAMEALIGN" \
"\4FIFOOFLOW\5GIANT\6RUNT" \
"\10BUFERR"
#define VR_RXCTL_BUFLEN 0x000007FF
#define VR_RXCTL_BUFLEN_EXT 0x00007800
#define VR_RXCTL_CHAIN 0x00008000
#define VR_RXCTL_TAG 0x00010000
#define VR_RXCTL_UDP 0x00020000
#define VR_RXCTL_TCP 0x00040000
#define VR_RXCTL_IP 0x00080000
#define VR_RXCTL_TCPUDPOK 0x00100000
#define VR_RXCTL_IPOK 0x00200000
#define VR_RXCTL_SNAPTAG 0x00400000
#define VR_RXCTL_RXLERR 0x00800000 /* 6105M */
#define VR_RXCTL_RX_INTR 0x00800000
#define VR_RXCTL (VR_RXCTL_CHAIN|VR_RXCTL_RX_INTR)
#define VR_TXSTAT_DEFER 0x00000001
#define VR_TXSTAT_UNDERRUN 0x00000002
#define VR_TXSTAT_COLLCNT 0x00000078
#define VR_TXSTAT_SQE 0x00000080
#define VR_TXSTAT_ABRT 0x00000100
#define VR_TXSTAT_LATECOLL 0x00000200
#define VR_TXSTAT_CARRLOST 0x00000400
#define VR_TXSTAT_UDF 0x00000800
#define VR_TXSTAT_TBUFF 0x00001000
#define VR_TXSTAT_BUSERR 0x00002000
#define VR_TXSTAT_JABTIMEO 0x00004000
#define VR_TXSTAT_ERRSUM 0x00008000
#define VR_TXSTAT_OWN 0x80000000
#define VR_TXCTL_BUFLEN 0x000007FF
#define VR_TXCTL_BUFLEN_EXT 0x00007800
#define VR_TXCTL_TLINK 0x00008000
#define VR_TXCTL_NOCRC 0x00010000
#define VR_TXCTL_INSERTTAG 0x00020000
#define VR_TXCTL_IPCSUM 0x00040000
#define VR_TXCTL_UDPCSUM 0x00080000
#define VR_TXCTL_TCPCSUM 0x00100000
#define VR_TXCTL_FIRSTFRAG 0x00200000
#define VR_TXCTL_LASTFRAG 0x00400000
#define VR_TXCTL_FINT 0x00800000
#define VR_MIN_FRAMELEN 60
#define VR_FLAG_FORCEDELAY 1
#define VR_FLAG_SCHEDDELAY 2
#define VR_FLAG_DELAYTIMEO 3
#define VR_TIMEOUT 1000
#define VR_MII_TIMEOUT 10000
#define VR_PHYADDR_MASK 0x1f
/*
* General constants that are fun to know.
*
* VIA vendor ID
*/
#define VIA_VENDORID 0x1106
/*
* VIA Rhine device IDs.
*/
#define VIA_DEVICEID_RHINE 0x3043
#define VIA_DEVICEID_RHINE_II 0x6100
#define VIA_DEVICEID_RHINE_II_2 0x3065
#define VIA_DEVICEID_RHINE_III 0x3106
#define VIA_DEVICEID_RHINE_III_M 0x3053
/*
* Delta Electronics device ID.
*/
#define DELTA_VENDORID 0x1500
/*
* Delta device IDs.
*/
#define DELTA_DEVICEID_RHINE_II 0x1320
/*
* Addtron vendor ID.
*/
#define ADDTRON_VENDORID 0x4033
/*
* Addtron device IDs.
*/
#define ADDTRON_DEVICEID_RHINE_II 0x1320
/*
* VIA Rhine revision IDs
*/
#define REV_ID_VT3043_E 0x04
#define REV_ID_VT3071_A 0x20
#define REV_ID_VT3071_B 0x21
#define REV_ID_VT6102_A 0x40
#define REV_ID_VT6102_B 0x41
#define REV_ID_VT6102_C 0x42
#define REV_ID_VT6102_APOLLO 0x74
#define REV_ID_VT6105_A0 0x80
#define REV_ID_VT6105_B0 0x83
#define REV_ID_VT6105_LOM 0x8A
#define REV_ID_VT6107_A0 0x8C
#define REV_ID_VT6107_A1 0x8D
#define REV_ID_VT6105M_A0 0x90
#define REV_ID_VT6105M_B1 0x94
/*
* PCI low memory base and low I/O base register, and
* other PCI registers.
*/
#define VR_PCI_VENDOR_ID 0x00
#define VR_PCI_DEVICE_ID 0x02
#define VR_PCI_COMMAND 0x04
#define VR_PCI_STATUS 0x06
#define VR_PCI_REVID 0x08
#define VR_PCI_CLASSCODE 0x09
#define VR_PCI_LATENCY_TIMER 0x0D
#define VR_PCI_HEADER_TYPE 0x0E
#define VR_PCI_LOIO 0x10
#define VR_PCI_LOMEM 0x14
#define VR_PCI_BIOSROM 0x30
#define VR_PCI_INTLINE 0x3C
#define VR_PCI_INTPIN 0x3D
#define VR_PCI_MINGNT 0x3E
#define VR_PCI_MINLAT 0x0F
#define VR_PCI_RESETOPT 0x48
#define VR_PCI_EEPROM_DATA 0x4C
#define VR_PCI_MODE0 0x50
#define VR_PCI_MODE2 0x52
#define VR_PCI_MODE3 0x53
#define VR_MODE2_PCEROPT 0x80 /* VT6102 only */
#define VR_MODE2_DISABT 0x40
#define VR_MODE2_MRDPL 0x08 /* VT6107A1 and above */
#define VR_MODE2_MODE10T 0x02
#define VR_MODE3_XONOPT 0x80
#define VR_MODE3_TPACEN 0x40
#define VR_MODE3_BACKOPT 0x20
#define VR_MODE3_DLTSEL 0x10
#define VR_MODE3_MIIDMY 0x08
#define VR_MODE3_MIION 0x04
/* power management registers */
#define VR_PCI_CAPID 0xDC /* 8 bits */
#define VR_PCI_NEXTPTR 0xDD /* 8 bits */
#define VR_PCI_PWRMGMTCAP 0xDE /* 16 bits */
#define VR_PCI_PWRMGMTCTRL 0xE0 /* 16 bits */
#define VR_PSTATE_MASK 0x0003
#define VR_PSTATE_D0 0x0000
#define VR_PSTATE_D1 0x0002
#define VR_PSTATE_D2 0x0002
#define VR_PSTATE_D3 0x0003
#define VR_PME_EN 0x0010
#define VR_PME_STATUS 0x8000
#define VR_RX_RING_CNT 128
#define VR_TX_RING_CNT 128
#define VR_TX_RING_SIZE sizeof(struct vr_desc) * VR_TX_RING_CNT
#define VR_RX_RING_SIZE sizeof(struct vr_desc) * VR_RX_RING_CNT
#define VR_RING_ALIGN sizeof(struct vr_desc)
#define VR_RX_ALIGN sizeof(uint32_t)
#define VR_MAXFRAGS 8
#define VR_TX_INTR_THRESH 8
#define VR_ADDR_LO(x) ((uint64_t)(x) & 0xffffffff)
#define VR_ADDR_HI(x) ((uint64_t)(x) >> 32)
#define VR_TX_RING_ADDR(sc, i) \
((sc)->vr_rdata.vr_tx_ring_paddr + sizeof(struct vr_desc) * (i))
#define VR_RX_RING_ADDR(sc, i) \
((sc)->vr_rdata.vr_rx_ring_paddr + sizeof(struct vr_desc) * (i))
#define VR_INC(x,y) (x) = (((x) + 1) % y)
struct vr_txdesc {
struct mbuf *tx_m;
bus_dmamap_t tx_dmamap;
};
struct vr_rxdesc {
struct mbuf *rx_m;
bus_dmamap_t rx_dmamap;
struct vr_desc *desc;
};
struct vr_chain_data {
bus_dma_tag_t vr_parent_tag;
bus_dma_tag_t vr_tx_tag;
struct vr_txdesc vr_txdesc[VR_TX_RING_CNT];
bus_dma_tag_t vr_rx_tag;
struct vr_rxdesc vr_rxdesc[VR_RX_RING_CNT];
bus_dma_tag_t vr_tx_ring_tag;
bus_dma_tag_t vr_rx_ring_tag;
bus_dmamap_t vr_tx_ring_map;
bus_dmamap_t vr_rx_ring_map;
bus_dmamap_t vr_rx_sparemap;
int vr_tx_pkts;
int vr_tx_prod;
int vr_tx_cons;
int vr_tx_cnt;
int vr_rx_cons;
};
struct vr_ring_data {
struct vr_desc *vr_rx_ring;
struct vr_desc *vr_tx_ring;
bus_addr_t vr_rx_ring_paddr;
bus_addr_t vr_tx_ring_paddr;
};
struct vr_statistics {
uint64_t tx_ok;
uint64_t rx_ok;
uint32_t tx_errors;
uint32_t rx_errors;
uint32_t rx_no_buffers;
uint32_t rx_no_mbufs;
uint32_t rx_crc_errors;
uint32_t rx_alignment;
uint32_t rx_fifo_overflows;
uint32_t rx_giants;
uint32_t rx_runts;
uint32_t tx_abort;
uint32_t tx_collisions;
uint32_t tx_late_collisions;
uint32_t tx_underrun;
uint32_t bus_errors;
uint32_t num_restart;
};
struct vr_softc {
struct ifnet *vr_ifp; /* interface info */
device_t vr_dev;
struct resource *vr_res;
int vr_res_id;
int vr_res_type;
struct resource *vr_irq;
void *vr_intrhand;
device_t vr_miibus;
uint8_t vr_revid; /* Rhine chip revision */
uint8_t vr_flags; /* See VR_F_* below */
#define VR_F_RESTART 0x01 /* Restart unit on next tick */
int vr_phyaddr;
int vr_if_flags;
struct task vr_link_task;
struct vr_chain_data vr_cdata;
struct vr_ring_data vr_rdata;
struct vr_statistics vr_stat;
struct callout vr_stat_callout;
struct mtx vr_mtx;
int vr_suspended; /* if 1, sleeping/detaching */
int vr_quirks;
int vr_link;
int vr_watchdog_timer;
int vr_txthresh;
int vr_detach;
#ifdef DEVICE_POLLING
int rxcycles;
#endif
};
#define VR_LOCK(_sc) mtx_lock(&(_sc)->vr_mtx)
#define VR_UNLOCK(_sc) mtx_unlock(&(_sc)->vr_mtx)
#define VR_LOCK_ASSERT(_sc) mtx_assert(&(_sc)->vr_mtx, MA_OWNED)
/*
* register space access macros
*/
#define CSR_WRITE_4(sc, reg, val) bus_write_4(sc->vr_res, reg, val)
#define CSR_WRITE_2(sc, reg, val) bus_write_2(sc->vr_res, reg, val)
#define CSR_WRITE_1(sc, reg, val) bus_write_1(sc->vr_res, reg, val)
#define CSR_READ_2(sc, reg) bus_read_2(sc->vr_res, reg)
#define CSR_READ_1(sc, reg) bus_read_1(sc->vr_res, reg)
#define VR_SETBIT(sc, reg, x) CSR_WRITE_1(sc, reg, CSR_READ_1(sc, reg) | (x))
#define VR_CLRBIT(sc, reg, x) CSR_WRITE_1(sc, reg, CSR_READ_1(sc, reg) & ~(x))
#define VR_SETBIT16(sc, reg, x) CSR_WRITE_2(sc, reg, CSR_READ_2(sc, reg) | (x))
#define VR_CLRBIT16(sc, reg, x) CSR_WRITE_2(sc, reg, CSR_READ_2(sc, reg) & ~(x))