d5558c001a
around && within ||' type warnings. I'm pretty sure I have not masked any problems here, I've committed real problem fixes seperately.
791 lines
18 KiB
C
791 lines
18 KiB
C
/*
|
|
* Copyright 1992 by the University of Guelph
|
|
*
|
|
* Permission to use, copy and modify this
|
|
* software and its documentation for any purpose and without
|
|
* fee is hereby granted, provided that the above copyright
|
|
* notice appear in all copies and that both that copyright
|
|
* notice and this permission notice appear in supporting
|
|
* documentation.
|
|
* University of Guelph makes no representations about the suitability of
|
|
* this software for any purpose. It is provided "as is"
|
|
* without express or implied warranty.
|
|
*
|
|
* $Id: mse.c,v 1.41 1999/05/06 18:12:28 peter Exp $
|
|
*/
|
|
/*
|
|
* Driver for the Logitech and ATI Inport Bus mice for use with 386bsd and
|
|
* the X386 port, courtesy of
|
|
* Rick Macklem, rick@snowhite.cis.uoguelph.ca
|
|
* Caveats: The driver currently uses spltty(), but doesn't use any
|
|
* generic tty code. It could use splmse() (that only masks off the
|
|
* bus mouse interrupt, but that would require hacking in i386/isa/icu.s.
|
|
* (This may be worth the effort, since the Logitech generates 30/60
|
|
* interrupts/sec continuously while it is open.)
|
|
* NB: The ATI has NOT been tested yet!
|
|
*/
|
|
|
|
/*
|
|
* Modification history:
|
|
* Sep 6, 1994 -- Lars Fredriksen(fredriks@mcs.com)
|
|
* improved probe based on input from Logitech.
|
|
*
|
|
* Oct 19, 1992 -- E. Stark (stark@cs.sunysb.edu)
|
|
* fixes to make it work with Microsoft InPort busmouse
|
|
*
|
|
* Jan, 1993 -- E. Stark (stark@cs.sunysb.edu)
|
|
* added patches for new "select" interface
|
|
*
|
|
* May 4, 1993 -- E. Stark (stark@cs.sunysb.edu)
|
|
* changed position of some spl()'s in mseread
|
|
*
|
|
* October 8, 1993 -- E. Stark (stark@cs.sunysb.edu)
|
|
* limit maximum negative x/y value to -127 to work around XFree problem
|
|
* that causes spurious button pushes.
|
|
*/
|
|
|
|
#include "mse.h"
|
|
#if NMSE > 0
|
|
#include "opt_devfs.h"
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/conf.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/poll.h>
|
|
#include <sys/select.h>
|
|
#include <sys/uio.h>
|
|
#ifdef DEVFS
|
|
#include <sys/devfsext.h>
|
|
#endif /*DEVFS*/
|
|
|
|
#include <machine/clock.h>
|
|
#include <machine/mouse.h>
|
|
|
|
#include <i386/isa/isa_device.h>
|
|
|
|
/* driver configuration flags (config) */
|
|
#define MSE_CONFIG_ACCEL 0x00f0 /* acceleration factor */
|
|
#define MSE_CONFIG_FLAGS (MSE_CONFIG_ACCEL)
|
|
|
|
static int mseprobe(struct isa_device *);
|
|
static int mseattach(struct isa_device *);
|
|
|
|
struct isa_driver msedriver = {
|
|
mseprobe, mseattach, "mse"
|
|
};
|
|
|
|
static d_open_t mseopen;
|
|
static d_close_t mseclose;
|
|
static d_read_t mseread;
|
|
static d_ioctl_t mseioctl;
|
|
static d_poll_t msepoll;
|
|
|
|
#define CDEV_MAJOR 27
|
|
static struct cdevsw mse_cdevsw =
|
|
{ mseopen, mseclose, mseread, nowrite, /*27*/
|
|
mseioctl, nostop, nullreset, nodevtotty,/* mse */
|
|
msepoll, nommap, NULL, "mse", NULL, -1 };
|
|
|
|
static ointhand2_t mseintr;
|
|
|
|
/*
|
|
* Software control structure for mouse. The sc_enablemouse(),
|
|
* sc_disablemouse() and sc_getmouse() routines must be called spl'd().
|
|
*/
|
|
static struct mse_softc {
|
|
int sc_flags;
|
|
int sc_mousetype;
|
|
struct selinfo sc_selp;
|
|
u_int sc_port;
|
|
void (*sc_enablemouse) __P((u_int port));
|
|
void (*sc_disablemouse) __P((u_int port));
|
|
void (*sc_getmouse) __P((u_int port, int *dx, int *dy, int *but));
|
|
int sc_deltax;
|
|
int sc_deltay;
|
|
int sc_obuttons;
|
|
int sc_buttons;
|
|
int sc_bytesread;
|
|
u_char sc_bytes[MOUSE_SYS_PACKETSIZE];
|
|
mousehw_t hw;
|
|
mousemode_t mode;
|
|
mousestatus_t status;
|
|
#ifdef DEVFS
|
|
void *devfs_token;
|
|
void *n_devfs_token;
|
|
#endif
|
|
} mse_sc[NMSE];
|
|
|
|
/* Flags */
|
|
#define MSESC_OPEN 0x1
|
|
#define MSESC_WANT 0x2
|
|
|
|
/* and Mouse Types */
|
|
#define MSE_NONE 0 /* don't move this! */
|
|
#define MSE_LOGITECH 0x1
|
|
#define MSE_ATIINPORT 0x2
|
|
#define MSE_LOGI_SIG 0xA5
|
|
|
|
#define MSE_PORTA 0
|
|
#define MSE_PORTB 1
|
|
#define MSE_PORTC 2
|
|
#define MSE_PORTD 3
|
|
|
|
#define MSE_UNIT(dev) (minor(dev) >> 1)
|
|
#define MSE_NBLOCKIO(dev) (minor(dev) & 0x1)
|
|
|
|
/*
|
|
* Logitech bus mouse definitions
|
|
*/
|
|
#define MSE_SETUP 0x91 /* What does this mean? */
|
|
/* The definition for the control port */
|
|
/* is as follows: */
|
|
|
|
/* D7 = Mode set flag (1 = active) */
|
|
/* D6,D5 = Mode selection (port A) */
|
|
/* 00 = Mode 0 = Basic I/O */
|
|
/* 01 = Mode 1 = Strobed I/O */
|
|
/* 10 = Mode 2 = Bi-dir bus */
|
|
/* D4 = Port A direction (1 = input)*/
|
|
/* D3 = Port C (upper 4 bits) */
|
|
/* direction. (1 = input) */
|
|
/* D2 = Mode selection (port B & C) */
|
|
/* 0 = Mode 0 = Basic I/O */
|
|
/* 1 = Mode 1 = Strobed I/O */
|
|
/* D1 = Port B direction (1 = input)*/
|
|
/* D0 = Port C (lower 4 bits) */
|
|
/* direction. (1 = input) */
|
|
|
|
/* So 91 means Basic I/O on all 3 ports,*/
|
|
/* Port A is an input port, B is an */
|
|
/* output port, C is split with upper */
|
|
/* 4 bits being an output port and lower*/
|
|
/* 4 bits an input port, and enable the */
|
|
/* sucker. */
|
|
/* Courtesy Intel 8255 databook. Lars */
|
|
#define MSE_HOLD 0x80
|
|
#define MSE_RXLOW 0x00
|
|
#define MSE_RXHIGH 0x20
|
|
#define MSE_RYLOW 0x40
|
|
#define MSE_RYHIGH 0x60
|
|
#define MSE_DISINTR 0x10
|
|
#define MSE_INTREN 0x00
|
|
|
|
static int mse_probelogi __P((struct isa_device *idp));
|
|
static void mse_disablelogi __P((u_int port));
|
|
static void mse_getlogi __P((u_int port, int *dx, int *dy, int *but));
|
|
static void mse_enablelogi __P((u_int port));
|
|
|
|
/*
|
|
* ATI Inport mouse definitions
|
|
*/
|
|
#define MSE_INPORT_RESET 0x80
|
|
#define MSE_INPORT_STATUS 0x00
|
|
#define MSE_INPORT_DX 0x01
|
|
#define MSE_INPORT_DY 0x02
|
|
#define MSE_INPORT_MODE 0x07
|
|
#define MSE_INPORT_HOLD 0x20
|
|
#define MSE_INPORT_INTREN 0x09
|
|
|
|
static int mse_probeati __P((struct isa_device *idp));
|
|
static void mse_enableati __P((u_int port));
|
|
static void mse_disableati __P((u_int port));
|
|
static void mse_getati __P((u_int port, int *dx, int *dy, int *but));
|
|
|
|
#define MSEPRI (PZERO + 3)
|
|
|
|
/*
|
|
* Table of mouse types.
|
|
* Keep the Logitech last, since I haven't figured out how to probe it
|
|
* properly yet. (Someday I'll have the documentation.)
|
|
*/
|
|
static struct mse_types {
|
|
int m_type; /* Type of bus mouse */
|
|
int (*m_probe) __P((struct isa_device *idp));
|
|
/* Probe routine to test for it */
|
|
void (*m_enable) __P((u_int port));
|
|
/* Start routine */
|
|
void (*m_disable) __P((u_int port));
|
|
/* Disable interrupts routine */
|
|
void (*m_get) __P((u_int port, int *dx, int *dy, int *but));
|
|
/* and get mouse status */
|
|
mousehw_t m_hw; /* buttons iftype type model hwid */
|
|
mousemode_t m_mode; /* proto rate res accel level size mask */
|
|
} mse_types[] = {
|
|
{ MSE_ATIINPORT,
|
|
mse_probeati, mse_enableati, mse_disableati, mse_getati,
|
|
{ 2, MOUSE_IF_INPORT, MOUSE_MOUSE, MOUSE_MODEL_GENERIC, 0, },
|
|
{ MOUSE_PROTO_INPORT, -1, -1, 0, 0, MOUSE_MSC_PACKETSIZE,
|
|
{ MOUSE_MSC_SYNCMASK, MOUSE_MSC_SYNC, }, }, },
|
|
{ MSE_LOGITECH,
|
|
mse_probelogi, mse_enablelogi, mse_disablelogi, mse_getlogi,
|
|
{ 2, MOUSE_IF_BUS, MOUSE_MOUSE, MOUSE_MODEL_GENERIC, 0, },
|
|
{ MOUSE_PROTO_BUS, -1, -1, 0, 0, MOUSE_MSC_PACKETSIZE,
|
|
{ MOUSE_MSC_SYNCMASK, MOUSE_MSC_SYNC, }, }, },
|
|
{ 0, },
|
|
};
|
|
|
|
int
|
|
mseprobe(idp)
|
|
register struct isa_device *idp;
|
|
{
|
|
register struct mse_softc *sc = &mse_sc[idp->id_unit];
|
|
register int i;
|
|
|
|
/*
|
|
* Check for each mouse type in the table.
|
|
*/
|
|
i = 0;
|
|
while (mse_types[i].m_type) {
|
|
if ((*mse_types[i].m_probe)(idp)) {
|
|
sc->sc_mousetype = mse_types[i].m_type;
|
|
sc->sc_enablemouse = mse_types[i].m_enable;
|
|
sc->sc_disablemouse = mse_types[i].m_disable;
|
|
sc->sc_getmouse = mse_types[i].m_get;
|
|
sc->hw = mse_types[i].m_hw;
|
|
sc->mode = mse_types[i].m_mode;
|
|
return (1);
|
|
}
|
|
i++;
|
|
}
|
|
return (0);
|
|
}
|
|
|
|
int
|
|
mseattach(idp)
|
|
struct isa_device *idp;
|
|
{
|
|
int unit = idp->id_unit;
|
|
struct mse_softc *sc = &mse_sc[unit];
|
|
|
|
idp->id_ointr = mseintr;
|
|
sc->sc_port = idp->id_iobase;
|
|
sc->mode.accelfactor = (idp->id_flags & MSE_CONFIG_ACCEL) >> 4;
|
|
#ifdef DEVFS
|
|
sc->devfs_token =
|
|
devfs_add_devswf(&mse_cdevsw, unit << 1, DV_CHR, 0, 0,
|
|
0600, "mse%d", unit);
|
|
sc->n_devfs_token =
|
|
devfs_add_devswf(&mse_cdevsw, (unit<<1)+1, DV_CHR,0, 0,
|
|
0600, "nmse%d", unit);
|
|
#endif
|
|
return (1);
|
|
}
|
|
|
|
/*
|
|
* Exclusive open the mouse, initialize it and enable interrupts.
|
|
*/
|
|
static int
|
|
mseopen(dev, flags, fmt, p)
|
|
dev_t dev;
|
|
int flags;
|
|
int fmt;
|
|
struct proc *p;
|
|
{
|
|
register struct mse_softc *sc;
|
|
int s;
|
|
|
|
if (MSE_UNIT(dev) >= NMSE)
|
|
return (ENXIO);
|
|
sc = &mse_sc[MSE_UNIT(dev)];
|
|
if (sc->sc_mousetype == MSE_NONE)
|
|
return (ENXIO);
|
|
if (sc->sc_flags & MSESC_OPEN)
|
|
return (EBUSY);
|
|
sc->sc_flags |= MSESC_OPEN;
|
|
sc->sc_obuttons = sc->sc_buttons = MOUSE_MSC_BUTTONS;
|
|
sc->sc_deltax = sc->sc_deltay = 0;
|
|
sc->sc_bytesread = sc->mode.packetsize = MOUSE_MSC_PACKETSIZE;
|
|
sc->mode.level = 0;
|
|
sc->status.flags = 0;
|
|
sc->status.button = sc->status.obutton = 0;
|
|
sc->status.dx = sc->status.dy = sc->status.dz = 0;
|
|
|
|
/*
|
|
* Initialize mouse interface and enable interrupts.
|
|
*/
|
|
s = spltty();
|
|
(*sc->sc_enablemouse)(sc->sc_port);
|
|
splx(s);
|
|
return (0);
|
|
}
|
|
|
|
/*
|
|
* mseclose: just turn off mouse innterrupts.
|
|
*/
|
|
static int
|
|
mseclose(dev, flags, fmt, p)
|
|
dev_t dev;
|
|
int flags;
|
|
int fmt;
|
|
struct proc *p;
|
|
{
|
|
struct mse_softc *sc = &mse_sc[MSE_UNIT(dev)];
|
|
int s;
|
|
|
|
s = spltty();
|
|
(*sc->sc_disablemouse)(sc->sc_port);
|
|
sc->sc_flags &= ~MSESC_OPEN;
|
|
splx(s);
|
|
return(0);
|
|
}
|
|
|
|
/*
|
|
* mseread: return mouse info using the MSC serial protocol, but without
|
|
* using bytes 4 and 5.
|
|
* (Yes this is cheesy, but it makes the X386 server happy, so...)
|
|
*/
|
|
static int
|
|
mseread(dev, uio, ioflag)
|
|
dev_t dev;
|
|
struct uio *uio;
|
|
int ioflag;
|
|
{
|
|
register struct mse_softc *sc = &mse_sc[MSE_UNIT(dev)];
|
|
int xfer, s, error;
|
|
|
|
/*
|
|
* If there are no protocol bytes to be read, set up a new protocol
|
|
* packet.
|
|
*/
|
|
s = spltty(); /* XXX Should be its own spl, but where is imlXX() */
|
|
if (sc->sc_bytesread >= sc->mode.packetsize) {
|
|
while (sc->sc_deltax == 0 && sc->sc_deltay == 0 &&
|
|
(sc->sc_obuttons ^ sc->sc_buttons) == 0) {
|
|
if (MSE_NBLOCKIO(dev)) {
|
|
splx(s);
|
|
return (0);
|
|
}
|
|
sc->sc_flags |= MSESC_WANT;
|
|
error = tsleep((caddr_t)sc, MSEPRI | PCATCH,
|
|
"mseread", 0);
|
|
if (error) {
|
|
splx(s);
|
|
return (error);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Generate protocol bytes.
|
|
* For some reason X386 expects 5 bytes but never uses
|
|
* the fourth or fifth?
|
|
*/
|
|
sc->sc_bytes[0] = sc->mode.syncmask[1]
|
|
| (sc->sc_buttons & ~sc->mode.syncmask[0]);
|
|
if (sc->sc_deltax > 127)
|
|
sc->sc_deltax = 127;
|
|
if (sc->sc_deltax < -127)
|
|
sc->sc_deltax = -127;
|
|
sc->sc_deltay = -sc->sc_deltay; /* Otherwise mousey goes wrong way */
|
|
if (sc->sc_deltay > 127)
|
|
sc->sc_deltay = 127;
|
|
if (sc->sc_deltay < -127)
|
|
sc->sc_deltay = -127;
|
|
sc->sc_bytes[1] = sc->sc_deltax;
|
|
sc->sc_bytes[2] = sc->sc_deltay;
|
|
sc->sc_bytes[3] = sc->sc_bytes[4] = 0;
|
|
sc->sc_bytes[5] = sc->sc_bytes[6] = 0;
|
|
sc->sc_bytes[7] = MOUSE_SYS_EXTBUTTONS;
|
|
sc->sc_obuttons = sc->sc_buttons;
|
|
sc->sc_deltax = sc->sc_deltay = 0;
|
|
sc->sc_bytesread = 0;
|
|
}
|
|
splx(s);
|
|
xfer = min(uio->uio_resid, sc->mode.packetsize - sc->sc_bytesread);
|
|
error = uiomove(&sc->sc_bytes[sc->sc_bytesread], xfer, uio);
|
|
if (error)
|
|
return (error);
|
|
sc->sc_bytesread += xfer;
|
|
return(0);
|
|
}
|
|
|
|
/*
|
|
* mseioctl: process ioctl commands.
|
|
*/
|
|
static int
|
|
mseioctl(dev, cmd, addr, flag, p)
|
|
dev_t dev;
|
|
u_long cmd;
|
|
caddr_t addr;
|
|
int flag;
|
|
struct proc *p;
|
|
{
|
|
register struct mse_softc *sc = &mse_sc[MSE_UNIT(dev)];
|
|
mousestatus_t status;
|
|
int err = 0;
|
|
int s;
|
|
|
|
switch (cmd) {
|
|
|
|
case MOUSE_GETHWINFO:
|
|
s = spltty();
|
|
*(mousehw_t *)addr = sc->hw;
|
|
if (sc->mode.level == 0)
|
|
((mousehw_t *)addr)->model = MOUSE_MODEL_GENERIC;
|
|
splx(s);
|
|
break;
|
|
|
|
case MOUSE_GETMODE:
|
|
s = spltty();
|
|
*(mousemode_t *)addr = sc->mode;
|
|
switch (sc->mode.level) {
|
|
case 0:
|
|
break;
|
|
case 1:
|
|
((mousemode_t *)addr)->protocol = MOUSE_PROTO_SYSMOUSE;
|
|
((mousemode_t *)addr)->syncmask[0] = MOUSE_SYS_SYNCMASK;
|
|
((mousemode_t *)addr)->syncmask[1] = MOUSE_SYS_SYNC;
|
|
break;
|
|
}
|
|
splx(s);
|
|
break;
|
|
|
|
case MOUSE_SETMODE:
|
|
switch (((mousemode_t *)addr)->level) {
|
|
case 0:
|
|
case 1:
|
|
break;
|
|
default:
|
|
return (EINVAL);
|
|
}
|
|
if (((mousemode_t *)addr)->accelfactor < -1)
|
|
return (EINVAL);
|
|
else if (((mousemode_t *)addr)->accelfactor >= 0)
|
|
sc->mode.accelfactor =
|
|
((mousemode_t *)addr)->accelfactor;
|
|
sc->mode.level = ((mousemode_t *)addr)->level;
|
|
switch (sc->mode.level) {
|
|
case 0:
|
|
sc->sc_bytesread = sc->mode.packetsize
|
|
= MOUSE_MSC_PACKETSIZE;
|
|
break;
|
|
case 1:
|
|
sc->sc_bytesread = sc->mode.packetsize
|
|
= MOUSE_SYS_PACKETSIZE;
|
|
break;
|
|
}
|
|
break;
|
|
|
|
case MOUSE_GETLEVEL:
|
|
*(int *)addr = sc->mode.level;
|
|
break;
|
|
|
|
case MOUSE_SETLEVEL:
|
|
switch (*(int *)addr) {
|
|
case 0:
|
|
sc->mode.level = *(int *)addr;
|
|
sc->sc_bytesread = sc->mode.packetsize
|
|
= MOUSE_MSC_PACKETSIZE;
|
|
break;
|
|
case 1:
|
|
sc->mode.level = *(int *)addr;
|
|
sc->sc_bytesread = sc->mode.packetsize
|
|
= MOUSE_SYS_PACKETSIZE;
|
|
break;
|
|
default:
|
|
return (EINVAL);
|
|
}
|
|
break;
|
|
|
|
case MOUSE_GETSTATUS:
|
|
s = spltty();
|
|
status = sc->status;
|
|
sc->status.flags = 0;
|
|
sc->status.obutton = sc->status.button;
|
|
sc->status.button = 0;
|
|
sc->status.dx = 0;
|
|
sc->status.dy = 0;
|
|
sc->status.dz = 0;
|
|
splx(s);
|
|
*(mousestatus_t *)addr = status;
|
|
break;
|
|
|
|
case MOUSE_READSTATE:
|
|
case MOUSE_READDATA:
|
|
return (ENODEV);
|
|
|
|
#if (defined(MOUSE_GETVARS))
|
|
case MOUSE_GETVARS:
|
|
case MOUSE_SETVARS:
|
|
return (ENODEV);
|
|
#endif
|
|
|
|
default:
|
|
return (ENOTTY);
|
|
}
|
|
return (err);
|
|
}
|
|
|
|
/*
|
|
* msepoll: check for mouse input to be processed.
|
|
*/
|
|
static int
|
|
msepoll(dev, events, p)
|
|
dev_t dev;
|
|
int events;
|
|
struct proc *p;
|
|
{
|
|
register struct mse_softc *sc = &mse_sc[MSE_UNIT(dev)];
|
|
int s;
|
|
int revents = 0;
|
|
|
|
s = spltty();
|
|
if (events & (POLLIN | POLLRDNORM)) {
|
|
if (sc->sc_bytesread != sc->mode.packetsize ||
|
|
sc->sc_deltax != 0 || sc->sc_deltay != 0 ||
|
|
(sc->sc_obuttons ^ sc->sc_buttons) != 0)
|
|
revents |= events & (POLLIN | POLLRDNORM);
|
|
else {
|
|
/*
|
|
* Since this is an exclusive open device, any previous
|
|
* proc pointer is trash now, so we can just assign it.
|
|
*/
|
|
selrecord(p, &sc->sc_selp);
|
|
}
|
|
}
|
|
splx(s);
|
|
return (revents);
|
|
}
|
|
|
|
/*
|
|
* mseintr: update mouse status. sc_deltax and sc_deltay are accumulative.
|
|
*/
|
|
static void
|
|
mseintr(unit)
|
|
int unit;
|
|
{
|
|
/*
|
|
* the table to turn MouseSystem button bits (MOUSE_MSC_BUTTON?UP)
|
|
* into `mousestatus' button bits (MOUSE_BUTTON?DOWN).
|
|
*/
|
|
static int butmap[8] = {
|
|
0,
|
|
MOUSE_BUTTON3DOWN,
|
|
MOUSE_BUTTON2DOWN,
|
|
MOUSE_BUTTON2DOWN | MOUSE_BUTTON3DOWN,
|
|
MOUSE_BUTTON1DOWN,
|
|
MOUSE_BUTTON1DOWN | MOUSE_BUTTON3DOWN,
|
|
MOUSE_BUTTON1DOWN | MOUSE_BUTTON2DOWN,
|
|
MOUSE_BUTTON1DOWN | MOUSE_BUTTON2DOWN | MOUSE_BUTTON3DOWN
|
|
};
|
|
register struct mse_softc *sc = &mse_sc[unit];
|
|
int dx, dy, but;
|
|
int sign;
|
|
|
|
#ifdef DEBUG
|
|
static int mse_intrcnt = 0;
|
|
if((mse_intrcnt++ % 10000) == 0)
|
|
printf("mseintr\n");
|
|
#endif /* DEBUG */
|
|
if ((sc->sc_flags & MSESC_OPEN) == 0)
|
|
return;
|
|
|
|
(*sc->sc_getmouse)(sc->sc_port, &dx, &dy, &but);
|
|
if (sc->mode.accelfactor > 0) {
|
|
sign = (dx < 0);
|
|
dx = dx * dx / sc->mode.accelfactor;
|
|
if (dx == 0)
|
|
dx = 1;
|
|
if (sign)
|
|
dx = -dx;
|
|
sign = (dy < 0);
|
|
dy = dy * dy / sc->mode.accelfactor;
|
|
if (dy == 0)
|
|
dy = 1;
|
|
if (sign)
|
|
dy = -dy;
|
|
}
|
|
sc->sc_deltax += dx;
|
|
sc->sc_deltay += dy;
|
|
sc->sc_buttons = but;
|
|
|
|
but = butmap[~but & MOUSE_MSC_BUTTONS];
|
|
sc->status.dx += dx;
|
|
sc->status.dy += dy;
|
|
sc->status.flags |= ((dx || dy) ? MOUSE_POSCHANGED : 0)
|
|
| (sc->status.button ^ but);
|
|
sc->status.button = but;
|
|
|
|
/*
|
|
* If mouse state has changed, wake up anyone wanting to know.
|
|
*/
|
|
if (sc->sc_deltax != 0 || sc->sc_deltay != 0 ||
|
|
(sc->sc_obuttons ^ sc->sc_buttons) != 0) {
|
|
if (sc->sc_flags & MSESC_WANT) {
|
|
sc->sc_flags &= ~MSESC_WANT;
|
|
wakeup((caddr_t)sc);
|
|
}
|
|
selwakeup(&sc->sc_selp);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Routines for the Logitech mouse.
|
|
*/
|
|
/*
|
|
* Test for a Logitech bus mouse and return 1 if it is.
|
|
* (until I know how to use the signature port properly, just disable
|
|
* interrupts and return 1)
|
|
*/
|
|
static int
|
|
mse_probelogi(idp)
|
|
register struct isa_device *idp;
|
|
{
|
|
|
|
int sig;
|
|
|
|
outb(idp->id_iobase + MSE_PORTD, MSE_SETUP);
|
|
/* set the signature port */
|
|
outb(idp->id_iobase + MSE_PORTB, MSE_LOGI_SIG);
|
|
|
|
DELAY(30000); /* 30 ms delay */
|
|
sig = inb(idp->id_iobase + MSE_PORTB) & 0xFF;
|
|
if (sig == MSE_LOGI_SIG) {
|
|
outb(idp->id_iobase + MSE_PORTC, MSE_DISINTR);
|
|
return(1);
|
|
} else {
|
|
if (bootverbose)
|
|
printf("mse%d: wrong signature %x\n",idp->id_unit,sig);
|
|
return(0);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Initialize Logitech mouse and enable interrupts.
|
|
*/
|
|
static void
|
|
mse_enablelogi(port)
|
|
register u_int port;
|
|
{
|
|
int dx, dy, but;
|
|
|
|
outb(port + MSE_PORTD, MSE_SETUP);
|
|
mse_getlogi(port, &dx, &dy, &but);
|
|
}
|
|
|
|
/*
|
|
* Disable interrupts for Logitech mouse.
|
|
*/
|
|
static void
|
|
mse_disablelogi(port)
|
|
register u_int port;
|
|
{
|
|
|
|
outb(port + MSE_PORTC, MSE_DISINTR);
|
|
}
|
|
|
|
/*
|
|
* Get the current dx, dy and button up/down state.
|
|
*/
|
|
static void
|
|
mse_getlogi(port, dx, dy, but)
|
|
register u_int port;
|
|
int *dx;
|
|
int *dy;
|
|
int *but;
|
|
{
|
|
register char x, y;
|
|
|
|
outb(port + MSE_PORTC, MSE_HOLD | MSE_RXLOW);
|
|
x = inb(port + MSE_PORTA);
|
|
*but = (x >> 5) & MOUSE_MSC_BUTTONS;
|
|
x &= 0xf;
|
|
outb(port + MSE_PORTC, MSE_HOLD | MSE_RXHIGH);
|
|
x |= (inb(port + MSE_PORTA) << 4);
|
|
outb(port + MSE_PORTC, MSE_HOLD | MSE_RYLOW);
|
|
y = (inb(port + MSE_PORTA) & 0xf);
|
|
outb(port + MSE_PORTC, MSE_HOLD | MSE_RYHIGH);
|
|
y |= (inb(port + MSE_PORTA) << 4);
|
|
*dx = x;
|
|
*dy = y;
|
|
outb(port + MSE_PORTC, MSE_INTREN);
|
|
}
|
|
|
|
/*
|
|
* Routines for the ATI Inport bus mouse.
|
|
*/
|
|
/*
|
|
* Test for a ATI Inport bus mouse and return 1 if it is.
|
|
* (do not enable interrupts)
|
|
*/
|
|
static int
|
|
mse_probeati(idp)
|
|
register struct isa_device *idp;
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < 2; i++)
|
|
if (inb(idp->id_iobase + MSE_PORTC) == 0xde)
|
|
return (1);
|
|
return (0);
|
|
}
|
|
|
|
/*
|
|
* Initialize ATI Inport mouse and enable interrupts.
|
|
*/
|
|
static void
|
|
mse_enableati(port)
|
|
register u_int port;
|
|
{
|
|
|
|
outb(port + MSE_PORTA, MSE_INPORT_RESET);
|
|
outb(port + MSE_PORTA, MSE_INPORT_MODE);
|
|
outb(port + MSE_PORTB, MSE_INPORT_INTREN);
|
|
}
|
|
|
|
/*
|
|
* Disable interrupts for ATI Inport mouse.
|
|
*/
|
|
static void
|
|
mse_disableati(port)
|
|
register u_int port;
|
|
{
|
|
|
|
outb(port + MSE_PORTA, MSE_INPORT_MODE);
|
|
outb(port + MSE_PORTB, 0);
|
|
}
|
|
|
|
/*
|
|
* Get current dx, dy and up/down button state.
|
|
*/
|
|
static void
|
|
mse_getati(port, dx, dy, but)
|
|
register u_int port;
|
|
int *dx;
|
|
int *dy;
|
|
int *but;
|
|
{
|
|
register char byte;
|
|
|
|
outb(port + MSE_PORTA, MSE_INPORT_MODE);
|
|
outb(port + MSE_PORTB, MSE_INPORT_HOLD);
|
|
outb(port + MSE_PORTA, MSE_INPORT_STATUS);
|
|
*but = ~inb(port + MSE_PORTB) & MOUSE_MSC_BUTTONS;
|
|
outb(port + MSE_PORTA, MSE_INPORT_DX);
|
|
byte = inb(port + MSE_PORTB);
|
|
*dx = byte;
|
|
outb(port + MSE_PORTA, MSE_INPORT_DY);
|
|
byte = inb(port + MSE_PORTB);
|
|
*dy = byte;
|
|
outb(port + MSE_PORTA, MSE_INPORT_MODE);
|
|
outb(port + MSE_PORTB, MSE_INPORT_INTREN);
|
|
}
|
|
|
|
static int mse_devsw_installed;
|
|
|
|
static void mse_drvinit(void *unused)
|
|
{
|
|
dev_t dev;
|
|
|
|
if( ! mse_devsw_installed ) {
|
|
dev = makedev(CDEV_MAJOR, 0);
|
|
cdevsw_add(&dev,&mse_cdevsw, NULL);
|
|
mse_devsw_installed = 1;
|
|
}
|
|
}
|
|
|
|
SYSINIT(msedev,SI_SUB_DRIVERS,SI_ORDER_MIDDLE+CDEV_MAJOR,mse_drvinit,NULL)
|
|
|
|
|
|
#endif /* NMSE */
|