freebsd-dev/contrib/ntp/ntpd/refclock_arc.c
1999-12-09 13:01:21 +00:00

1324 lines
42 KiB
C

/*
* refclock_arc - clock driver for ARCRON MSF receivers
*/
#ifdef HAVE_CONFIG_H
#include <config.h>
#endif
#if defined(REFCLOCK) && defined(CLOCK_ARCRON_MSF)
static const char arc_version[] = { "V1.1 1997/06/23" };
#undef ARCRON_DEBUG /* Define only while in development... */
#ifndef ARCRON_NOT_KEEN
#define ARCRON_KEEN 1 /* Be keen, and trusting of the clock, if defined. */
#endif
#ifndef ARCRON_NOT_MULTIPLE_SAMPLES
#define ARCRON_MULTIPLE_SAMPLES 1 /* Use all timestamp bytes as samples. */
#endif
#ifndef ARCRON_NOT_LEAPSECOND_KEEN
#ifndef ARCRON_LEAPSECOND_KEEN
#undef ARCRON_LEAPSECOND_KEEN /* Respond quickly to leap seconds: doesn't work yet. */
#endif
#endif
/*
Code by Derek Mulcahy, <derek@toybox.demon.co.uk>, 1997.
Modifications by Damon Hart-Davis, <d@hd.org>, 1997.
THIS CODE IS SUPPLIED AS IS, WITH NO WARRANTY OF ANY KIND. USE AT
YOUR OWN RISK.
Orginally developed and used with ntp3-5.85 by Derek Mulcahy.
Built against ntp3-5.90 on Solaris 2.5 using gcc 2.7.2.
This code may be freely copied and used and incorporated in other
systems providing the disclaimer and notice of authorship are
reproduced.
-------------------------------------------------------------------------------
Author's original note:
I enclose my ntp driver for the Galleon Systems Arc MSF receiver.
It works (after a fashion) on both Solaris-1 and Solaris-2.
I am currently using ntp3-5.85. I have been running the code for
about 7 months without any problems. Even coped with the change to BST!
I had to do some funky things to read from the clock because it uses the
power from the receive lines to drive the transmit lines. This makes the
code look a bit stupid but it works. I also had to put in some delays to
allow for the turnaround time from receive to transmit. These delays
are between characters when requesting a time stamp so that shouldn't affect
the results too drastically.
...
The bottom line is that it works but could easily be improved. You are
free to do what you will with the code. I haven't been able to determine
how good the clock is. I think that this requires a known good clock
to compare it against.
-------------------------------------------------------------------------------
Damon's notes for adjustments:
MAJOR CHANGES SINCE V1.0
========================
1) Removal of pollcnt variable that made the clock go permanently
off-line once two time polls failed to gain responses.
2) Avoiding (at least on Solaris-2) terminal becoming the controlling
terminal of the process when we do a low-level open().
3) Additional logic (conditional on ARCRON_LEAPSECOND_KEEN being
defined) to try to resync quickly after a potential leap-second
insertion or deletion.
4) Code significantly slimmer at run-time than V1.0.
GENERAL
=======
1) The C preprocessor symbol to have the clock built has been changed
from ARC to ARCRON_MSF to CLOCK_ARCRON_MSF to minimise the
possiblity of clashes with other symbols in the future.
2) PRECISION should be -4/-5 (63ms/31ms) for the following reasons:
a) The ARC documentation claims the internal clock is (only)
accurate to about 20ms relative to Rugby (plus there must be
noticable drift and delay in the ms range due to transmission
delays and changing atmospheric effects). This clock is not
designed for ms accuracy as NTP has spoilt us all to expect.
b) The clock oscillator looks like a simple uncompensated quartz
crystal of the sort used in digital watches (ie 32768Hz) which
can have large temperature coefficients and drifts; it is not
clear if this oscillator is properly disciplined to the MSF
transmission, but as the default is to resync only once per
*day*, we can imagine that it is not, and is free-running. We
can minimise drift by resyncing more often (at the cost of
reduced battery life), but drift/wander may still be
significant.
c) Note that the bit time of 3.3ms adds to the potential error in
the the clock timestamp, since the bit clock of the serial link
may effectively be free-running with respect to the host clock
and the MSF clock. Actually, the error is probably 1/16th of
the above, since the input data is probably sampled at at least
16x the bit rate.
By keeping the clock marked as not very precise, it will have a
fairly large dispersion, and thus will tend to be used as a
`backup' time source and sanity checker, which this clock is
probably ideal for. For an isolated network without other time
sources, this clock can probably be expected to provide *much*
better than 1s accuracy, which will be fine.
By default, PRECISION is set to -4, but experience, especially at a
particular geographic location with a particular clock, may allow
this to be altered to -5. (Note that skews of +/- 10ms are to be
expected from the clock from time-to-time.) This improvement of
reported precision can be instigated by setting flag3 to 1, though
the PRECISION will revert to the normal value while the clock
signal quality is unknown whatever the flag3 setting.
IN ANY CASE, BE SURE TO SET AN APPROPRIATE FUDGE FACTOR TO REMOVE
ANY RESIDUAL SKEW, eg:
server 127.127.27.0 # ARCRON MSF radio clock unit 0.
# Fudge timestamps by about 20ms.
fudge 127.127.27.0 time1 0.020
You will need to observe your system's behaviour, assuming you have
some other NTP source to compare it with, to work out what the
fudge factor should be. For my Sun SS1 running SunOS 4.1.3_U1 with
my MSF clock with my distance from the MSF transmitter, +20ms
seemed about right, after some observation.
3) REFID has been made "MSFa" to reflect the MSF time source and the
ARCRON receiver.
4) DEFAULT_RESYNC_TIME is the time in seconds (by default) before
forcing a resync since the last attempt. This is picked to give a
little less than an hour between resyncs and to try to avoid
clashing with any regular event at a regular time-past-the-hour
which might cause systematic errors.
The INITIAL_RESYNC_DELAY is to avoid bothering the clock and
running down its batteries unnecesarily if ntpd is going to crash
or be killed or reconfigured quickly. If ARCRON_KEEN is defined
then this period is long enough for (with normal polling rates)
enough time samples to have been taken to allow ntpd to sync to
the clock before the interruption for the clock to resync to MSF.
This avoids ntpd syncing to another peer first and then
almost immediately hopping to the MSF clock.
The RETRY_RESYNC_TIME is used before rescheduling a resync after a
resync failed to reveal a statisfatory signal quality (too low or
unknown).
5) The clock seems quite jittery, so I have increased the
median-filter size from the typical (previous) value of 3. I
discard up to half the results in the filter. It looks like maybe
1 sample in 10 or so (maybe less) is a spike, so allow the median
filter to discard at least 10% of its entries or 1 entry, whichever
is greater.
6) Sleeping *before* each character sent to the unit to allow required
inter-character time but without introducting jitter and delay in
handling the response if possible.
7) If the flag ARCRON_KEEN is defined, take time samples whenever
possible, even while resyncing, etc. We rely, in this case, on the
clock always giving us a reasonable time or else telling us in the
status byte at the end of the timestamp that it failed to sync to
MSF---thus we should never end up syncing to completely the wrong
time.
8) If the flag ARCRON_OWN_FILTER is defined, use own versions of
refclock median-filter routines to get round small bug in 3-5.90
code which does not return the median offset. XXX Removed this
bit due NTP Version 4 upgrade - dlm.
9) We would appear to have a year-2000 problem with this clock since
it returns only the two least-significant digits of the year. But
ntpd ignores the year and uses the local-system year instead, so
this is in fact not a problem. Nevertheless, we attempt to do a
sensible thing with the dates, wrapping them into a 100-year
window.
10)Logs stats information that can be used by Derek's Tcl/Tk utility
to show the status of the clock.
11)The clock documentation insists that the number of bits per
character to be sent to the clock, and sent by it, is 11, including
one start bit and two stop bits. The data format is either 7+even
or 8+none.
TO-DO LIST
==========
* Eliminate use of scanf(), and maybe sprintf().
* Allow user setting of resync interval to trade battery life for
accuracy; maybe could be done via fudge factor or unit number.
* Possibly note the time since the last resync of the MSF clock to
MSF as the age of the last reference timestamp, ie trust the
clock's oscillator not very much...
* Add very slow auto-adjustment up to a value of +/- time2 to correct
for long-term errors in the clock value (time2 defaults to 0 so the
correction would be disabled by default).
* Consider trying to use the tty_clk/ppsclock support.
* Possibly use average or maximum signal quality reported during
resync, rather than just the last one, which may be atypical.
*/
/* Notes for HKW Elektronik GmBH Radio clock driver */
/* Author Lyndon David, Sentinet Ltd, Feb 1997 */
/* These notes seem also to apply usefully to the ARCRON clock. */
/* The HKW clock module is a radio receiver tuned into the Rugby */
/* MSF time signal tranmitted on 60 kHz. The clock module connects */
/* to the computer via a serial line and transmits the time encoded */
/* in 15 bytes at 300 baud 7 bits two stop bits even parity */
/* Clock communications, from the datasheet */
/* All characters sent to the clock are echoed back to the controlling */
/* device. */
/* Transmit time/date information */
/* syntax ASCII o<cr> */
/* Character o may be replaced if neccesary by a character whose code */
/* contains the lowest four bits f(hex) eg */
/* syntax binary: xxxx1111 00001101 */
/* DHD note:
You have to wait for character echo + 10ms before sending next character.
*/
/* The clock replies to this command with a sequence of 15 characters */
/* which contain the complete time and a final <cr> making 16 characters */
/* in total. */
/* The RC computer clock will not reply immediately to this command because */
/* the start bit edge of the first reply character marks the beginning of */
/* the second. So the RC Computer Clock will reply to this command at the */
/* start of the next second */
/* The characters have the following meaning */
/* 1. hours tens */
/* 2. hours units */
/* 3. minutes tens */
/* 4. minutes units */
/* 5. seconds tens */
/* 6. seconds units */
/* 7. day of week 1-monday 7-sunday */
/* 8. day of month tens */
/* 9. day of month units */
/* 10. month tens */
/* 11. month units */
/* 12. year tens */
/* 13. year units */
/* 14. BST/UTC status */
/* bit 7 parity */
/* bit 6 always 0 */
/* bit 5 always 1 */
/* bit 4 always 1 */
/* bit 3 always 0 */
/* bit 2 =1 if UTC is in effect, complementary to the BST bit */
/* bit 1 =1 if BST is in effect, according to the BST bit */
/* bit 0 BST/UTC change impending bit=1 in case of change impending */
/* 15. status */
/* bit 7 parity */
/* bit 6 always 0 */
/* bit 5 always 1 */
/* bit 4 always 1 */
/* bit 3 =1 if low battery is detected */
/* bit 2 =1 if the very last reception attempt failed and a valid */
/* time information already exists (bit0=1) */
/* =0 if the last reception attempt was successful */
/* bit 1 =1 if at least one reception since 2:30 am was successful */
/* =0 if no reception attempt since 2:30 am was successful */
/* bit 0 =1 if the RC Computer Clock contains valid time information */
/* This bit is zero after reset and one after the first */
/* successful reception attempt */
/* DHD note:
Also note g<cr> command which confirms that a resync is in progress, and
if so what signal quality (0--5) is available.
Also note h<cr> command which starts a resync to MSF signal.
*/
#include <stdio.h>
#include <ctype.h>
#include <sys/time.h>
#if defined(HAVE_BSD_TTYS)
#include <sgtty.h>
#endif /* HAVE_BSD_TTYS */
#if defined(HAVE_SYSV_TTYS)
#include <termio.h>
#endif /* HAVE_SYSV_TTYS */
#if defined(HAVE_TERMIOS)
#include <termios.h>
#endif
#include "ntpd.h"
#include "ntp_io.h"
#include "ntp_refclock.h"
#include "ntp_stdlib.h"
/*
* This driver supports the ARCRON MSF Radio Controlled Clock
*/
/*
* Interface definitions
*/
#define DEVICE "/dev/arc%d" /* Device name and unit. */
#define SPEED B300 /* UART speed (300 baud) */
#define PRECISION (-4) /* Precision (~63 ms). */
#define HIGHPRECISION (-5) /* If things are going well... */
#define REFID "MSFa" /* Reference ID. */
#define DESCRIPTION "ARCRON MSF Receiver"
#define NSAMPLESLONG 8 /* Stages of long filter. */
#define LENARC 16 /* Format `o' timecode length. */
#define BITSPERCHAR 11 /* Bits per character. */
#define BITTIME 0x0DA740E /* Time for 1 bit at 300bps. */
#define CHARTIME10 0x8888888 /* Time for 10-bit char at 300bps. */
#define CHARTIME11 0x962FC96 /* Time for 11-bit char at 300bps. */
#define CHARTIME /* Time for char at 300bps. */ \
( (BITSPERCHAR == 11) ? CHARTIME11 : ( (BITSPERCHAR == 10) ? CHARTIME10 : \
(BITSPERCHAR * BITTIME) ) )
/* Allow for UART to accept char half-way through final stop bit. */
#define INITIALOFFSET (u_int32)(-BITTIME/2)
/*
charoffsets[x] is the time after the start of the second that byte
x (with the first byte being byte 1) is received by the UART,
assuming that the initial edge of the start bit of the first byte
is on-time. The values are represented as the fractional part of
an l_fp.
We store enough values to have the offset of each byte including
the trailing \r, on the assumption that the bytes follow one
another without gaps.
*/
static const u_int32 charoffsets[LENARC+1] = {
#if BITSPERCHAR == 11 /* Usual case. */
/* Offsets computed as accurately as possible... */
0,
INITIALOFFSET + 0x0962fc96, /* 1 chars, 11 bits */
INITIALOFFSET + 0x12c5f92c, /* 2 chars, 22 bits */
INITIALOFFSET + 0x1c28f5c3, /* 3 chars, 33 bits */
INITIALOFFSET + 0x258bf259, /* 4 chars, 44 bits */
INITIALOFFSET + 0x2eeeeeef, /* 5 chars, 55 bits */
INITIALOFFSET + 0x3851eb85, /* 6 chars, 66 bits */
INITIALOFFSET + 0x41b4e81b, /* 7 chars, 77 bits */
INITIALOFFSET + 0x4b17e4b1, /* 8 chars, 88 bits */
INITIALOFFSET + 0x547ae148, /* 9 chars, 99 bits */
INITIALOFFSET + 0x5dddddde, /* 10 chars, 110 bits */
INITIALOFFSET + 0x6740da74, /* 11 chars, 121 bits */
INITIALOFFSET + 0x70a3d70a, /* 12 chars, 132 bits */
INITIALOFFSET + 0x7a06d3a0, /* 13 chars, 143 bits */
INITIALOFFSET + 0x8369d037, /* 14 chars, 154 bits */
INITIALOFFSET + 0x8ccccccd, /* 15 chars, 165 bits */
INITIALOFFSET + 0x962fc963 /* 16 chars, 176 bits */
#else
/* Offsets computed with a small rounding error... */
0,
INITIALOFFSET + 1 * CHARTIME,
INITIALOFFSET + 2 * CHARTIME,
INITIALOFFSET + 3 * CHARTIME,
INITIALOFFSET + 4 * CHARTIME,
INITIALOFFSET + 5 * CHARTIME,
INITIALOFFSET + 6 * CHARTIME,
INITIALOFFSET + 7 * CHARTIME,
INITIALOFFSET + 8 * CHARTIME,
INITIALOFFSET + 9 * CHARTIME,
INITIALOFFSET + 10 * CHARTIME,
INITIALOFFSET + 11 * CHARTIME,
INITIALOFFSET + 12 * CHARTIME,
INITIALOFFSET + 13 * CHARTIME,
INITIALOFFSET + 14 * CHARTIME,
INITIALOFFSET + 15 * CHARTIME,
INITIALOFFSET + 16 * CHARTIME
#endif
};
/* Chose filter length dependent on fudge flag 4. */
#define CHOSENSAMPLES(pp) \
(((pp)->sloppyclockflag & CLK_FLAG4) ? NSAMPLESLONG : NSAMPLES)
/*
Chose how many filter samples to keep. Several factors are in play.
1) Discard at least one sample to allow a spike value to be
discarded.
2) Discard about 1-in-8 to 1-in-30 samples to handle spikes.
3) Keep an odd number of samples to avoid median value being biased
high or low.
*/
#define NKEEP(pp) ((CHOSENSAMPLES(pp) - 1 - (CHOSENSAMPLES(pp)>>3)) | 1)
#define DEFAULT_RESYNC_TIME (57*60) /* Gap between resync attempts (s). */
#define RETRY_RESYNC_TIME (27*60) /* Gap to emergency resync attempt. */
#ifdef ARCRON_KEEN
#define INITIAL_RESYNC_DELAY 500 /* Delay before first resync. */
#else
#define INITIAL_RESYNC_DELAY 50 /* Delay before first resync. */
#endif
static const int moff[12] =
{ 0, 31, 59, 90, 120, 151, 181, 212, 243, 273, 304, 334 };
/* Flags for a raw open() of the clock serial device. */
#ifdef O_NOCTTY /* Good, we can avoid tty becoming controlling tty. */
#define OPEN_FLAGS (O_RDWR | O_NOCTTY)
#else /* Oh well, it may not matter... */
#define OPEN_FLAGS (O_RDWR)
#endif
/* Length of queue of command bytes to be sent. */
#define CMDQUEUELEN 4 /* Enough for two cmds + each \r. */
/* Queue tick time; interval in seconds between chars taken off queue. */
/* Must be >= 2 to allow o\r response to come back uninterrupted. */
#define QUEUETICK 2 /* Allow o\r reply to finish. */
/*
* ARC unit control structure
*/
struct arcunit {
l_fp lastrec; /* Time tag for the receive time (system). */
int status; /* Clock status. */
int quality; /* Quality of reception 0--5 for unit. */
/* We may also use the values -1 or 6 internally. */
u_long next_resync; /* Next resync time (s) compared to current_time. */
int resyncing; /* Resync in progress if true. */
/* In the outgoing queue, cmdqueue[0] is next to be sent. */
char cmdqueue[CMDQUEUELEN+1]; /* Queue of outgoing commands + \0. */
u_long saved_flags; /* Saved fudge flags. */
};
#ifdef ARCRON_LEAPSECOND_KEEN
/* The flag `possible_leap' is set non-zero when any MSF unit
thinks a leap-second may have happened.
Set whenever we receive a valid time sample in the first hour of
the first day of the first/seventh months.
Outside the special hour this value is unconditionally set
to zero by the receive routine.
On finding itself in this timeslot, as long as the value is
non-negative, the receive routine sets it to a positive value to
indicate a resync to MSF should be performed.
In the poll routine, if this value is positive and we are not
already resyncing (eg from a sync that started just before
midnight), start resyncing and set this value negative to
indicate that a leap-triggered resync has been started. Having
set this negative prevents the receive routine setting it
positive and thus prevents multiple resyncs during the witching
hour.
*/
static int possible_leap = 0; /* No resync required by default. */
#endif
#if 0
static void dummy_event_handler P((struct peer *));
static void arc_event_handler P((struct peer *));
#endif /* 0 */
#define QUALITY_UNKNOWN -1 /* Indicates unknown clock quality. */
#define MIN_CLOCK_QUALITY 0 /* Min quality clock will return. */
#define MIN_CLOCK_QUALITY_OK 3 /* Min quality for OK reception. */
#define MAX_CLOCK_QUALITY 5 /* Max quality clock will return. */
/*
* Function prototypes
*/
static int arc_start P((int, struct peer *));
static void arc_shutdown P((int, struct peer *));
static void arc_receive P((struct recvbuf *));
static void arc_poll P((int, struct peer *));
/*
* Transfer vector
*/
struct refclock refclock_arc = {
arc_start, /* start up driver */
arc_shutdown, /* shut down driver */
arc_poll, /* transmit poll message */
noentry, /* not used (old arc_control) */
noentry, /* initialize driver (not used) */
noentry, /* not used (old arc_buginfo) */
NOFLAGS /* not used */
};
/* Queue us up for the next tick. */
#define ENQUEUE(up) \
do { \
if((up)->ev.next != 0) { break; } /* WHOOPS! */ \
peer->nextdate = current_time + QUEUETICK; \
} while(0)
#if 0
/* Placeholder event handler---does nothing safely---soaks up lose tick. */
static void
dummy_event_handler(
struct peer *peer
)
{
#ifdef ARCRON_DEBUG
if(debug) { printf("arc: dummy_event_handler() called.\n"); }
#endif
}
/*
Normal event handler.
Take first character off queue and send to clock if not a null.
Shift characters down and put a null on the end.
We assume that there is no parallelism so no race condition, but even
if there is nothing bad will happen except that we might send some bad
data to the clock once in a while.
*/
static void
arc_event_handler(
struct peer *peer
)
{
struct refclockproc *pp = peer->procptr;
register struct arcunit *up = (struct arcunit *)pp->unitptr;
int i;
char c;
#ifdef ARCRON_DEBUG
if(debug > 2) { printf("arc: arc_event_handler() called.\n"); }
#endif
c = up->cmdqueue[0]; /* Next char to be sent. */
/* Shift down characters, shifting trailing \0 in at end. */
for(i = 0; i < CMDQUEUELEN; ++i)
{ up->cmdqueue[i] = up->cmdqueue[i+1]; }
/* Don't send '\0' characters. */
if(c != '\0') {
if(write(pp->io.fd, &c, 1) != 1) {
msyslog(LOG_NOTICE, "ARCRON: write to fd %d failed", pp->io.fd);
}
#ifdef ARCRON_DEBUG
else if(debug) { printf("arc: sent `%2.2x', fd %d.\n", c, pp->io.fd); }
#endif
}
}
#endif /* 0 */
/*
* arc_start - open the devices and initialize data for processing
*/
static int
arc_start(
int unit,
struct peer *peer
)
{
register struct arcunit *up;
struct refclockproc *pp;
int fd;
char device[20];
#ifdef HAVE_TERMIOS
struct termios arg;
#endif
msyslog(LOG_NOTICE, "ARCRON: %s: opening unit %d", arc_version, unit);
#ifdef ARCRON_DEBUG
if(debug) {
printf("arc: %s: attempt to open unit %d.\n", arc_version, unit);
}
#endif
/* Prevent a ridiculous device number causing overflow of device[]. */
if((unit < 0) || (unit > 255)) { return(0); }
/*
* Open serial port. Use CLK line discipline, if available.
*/
(void)sprintf(device, DEVICE, unit);
if (!(fd = refclock_open(device, SPEED, LDISC_CLK)))
return(0);
#ifdef ARCRON_DEBUG
if(debug) { printf("arc: unit %d using open().\n", unit); }
#endif
fd = open(device, OPEN_FLAGS);
if(fd < 0) {
#ifdef DEBUG
if(debug) { printf("arc: failed [open()] to open %s.\n", device); }
#endif
return(0);
}
fcntl(fd, F_SETFL, 0); /* clear the descriptor flags */
#ifdef ARCRON_DEBUG
if(debug)
{ printf("Opened RS232 port with file descriptor %d.\n", fd); }
#endif
#ifdef HAVE_TERMIOS
arg.c_iflag = IGNBRK | ISTRIP;
arg.c_oflag = 0;
arg.c_cflag = B300 | CS8 | CREAD | CLOCAL | CSTOPB;
arg.c_lflag = 0;
arg.c_cc[VMIN] = 1;
arg.c_cc[VTIME] = 0;
tcsetattr(fd, TCSANOW, &arg);
#else
msyslog(LOG_ERR, "ARCRON: termios not supported in this driver");
(void)close(fd);
return 0;
#endif
up = (struct arcunit *) emalloc(sizeof(struct arcunit));
if(!up) { (void) close(fd); return(0); }
/* Set structure to all zeros... */
memset((char *)up, 0, sizeof(struct arcunit));
pp = peer->procptr;
pp->io.clock_recv = arc_receive;
pp->io.srcclock = (caddr_t)peer;
pp->io.datalen = 0;
pp->io.fd = fd;
if(!io_addclock(&pp->io)) { (void) close(fd); free(up); return(0); }
pp->unitptr = (caddr_t)up;
/*
* Initialize miscellaneous variables
*/
peer->precision = PRECISION;
peer->stratum = 2; /* Default to stratum 2 not 0. */
pp->clockdesc = DESCRIPTION;
memcpy((char *)&pp->refid, REFID, 4);
/* Spread out resyncs so that they should remain separated. */
up->next_resync = current_time + INITIAL_RESYNC_DELAY + (67*unit)%1009;
#if 0 /* Not needed because of zeroing of arcunit structure... */
up->resyncing = 0; /* Not resyncing yet. */
up->saved_flags = 0; /* Default is all flags off. */
/* Clear send buffer out... */
{
int i;
for(i = CMDQUEUELEN; i >= 0; --i) { up->cmdqueue[i] = '\0'; }
}
#endif
#ifdef ARCRON_KEEN
up->quality = QUALITY_UNKNOWN; /* Trust the clock immediately. */
#else
up->quality = MIN_CLOCK_QUALITY;/* Don't trust the clock yet. */
#endif
return(1);
}
/*
* arc_shutdown - shut down the clock
*/
static void
arc_shutdown(
int unit,
struct peer *peer
)
{
register struct arcunit *up;
struct refclockproc *pp;
pp = peer->procptr;
up = (struct arcunit *)pp->unitptr;
io_closeclock(&pp->io);
free(up);
}
/*
Compute space left in output buffer.
*/
static int
space_left(
register struct arcunit *up
)
{
int spaceleft;
/* Compute space left in buffer after any pending output. */
for(spaceleft = 0; spaceleft < CMDQUEUELEN; ++spaceleft)
{ if(up->cmdqueue[CMDQUEUELEN - 1 - spaceleft] != '\0') { break; } }
return(spaceleft);
}
/*
Send command by copying into command buffer as far forward as possible,
after any pending output.
Indicate an error by returning 0 if there is not space for the command.
*/
static int
send_slow(
register struct arcunit *up,
int fd,
const char *s
)
{
int sl = strlen(s);
int spaceleft = space_left(up);
#ifdef ARCRON_DEBUG
if(debug > 1) { printf("arc: spaceleft = %d.\n", spaceleft); }
#endif
if(spaceleft < sl) { /* Should not normally happen... */
#ifdef ARCRON_DEBUG
msyslog(LOG_NOTICE, "ARCRON: send-buffer overrun (%d/%d)",
sl, spaceleft);
#endif
return(0); /* FAILED! */
}
/* Copy in the command to be sent. */
while(*s) { up->cmdqueue[CMDQUEUELEN - spaceleft--] = *s++; }
return(1);
}
/* Macro indicating action we will take for different quality values. */
#define quality_action(q) \
(((q) == QUALITY_UNKNOWN) ? "UNKNOWN, will use clock anyway" : \
(((q) < MIN_CLOCK_QUALITY_OK) ? "TOO POOR, will not use clock" : \
"OK, will use clock"))
/*
* arc_receive - receive data from the serial interface
*/
static void
arc_receive(
struct recvbuf *rbufp
)
{
register struct arcunit *up;
struct refclockproc *pp;
struct peer *peer;
char c;
int i, n, wday, month, bst, status;
int arc_last_offset;
/*
* Initialize pointers and read the timecode and timestamp
*/
peer = (struct peer *)rbufp->recv_srcclock;
pp = peer->procptr;
up = (struct arcunit *)pp->unitptr;
/*
If the command buffer is empty, and we are resyncing, insert a
g\r quality request into it to poll for signal quality again.
*/
if((up->resyncing) && (space_left(up) == CMDQUEUELEN)) {
#ifdef DEBUG
if(debug > 1) { printf("arc: inserting signal-quality poll.\n"); }
#endif
send_slow(up, pp->io.fd, "g\r");
}
/*
The `arc_last_offset' is the offset in lastcode[] of the last byte
received, and which we assume actually received the input
timestamp.
(When we get round to using tty_clk and it is available, we
assume that we will receive the whole timecode with the
trailing \r, and that that \r will be timestamped. But this
assumption also works if receive the characters one-by-one.)
*/
arc_last_offset = pp->lencode+rbufp->recv_length - 1;
/*
We catch a timestamp iff:
* The command code is `o' for a timestamp.
* If ARCRON_MULTIPLE_SAMPLES is undefined then we must have
exactly char in the buffer (the command code) so that we
only sample the first character of the timecode as our
`on-time' character.
* The first character in the buffer is not the echoed `\r'
from the `o` command (so if we are to timestamp an `\r' it
must not be first in the receive buffer with lencode==1.
(Even if we had other characters following it, we probably
would have a premature timestamp on the '\r'.)
* We have received at least one character (I cannot imagine
how it could be otherwise, but anyway...).
*/
c = rbufp->recv_buffer[0];
if((pp->a_lastcode[0] == 'o') &&
#ifndef ARCRON_MULTIPLE_SAMPLES
(pp->lencode == 1) &&
#endif
((pp->lencode != 1) || (c != '\r')) &&
(arc_last_offset >= 1)) {
/* Note that the timestamp should be corrected if >1 char rcvd. */
l_fp timestamp;
timestamp = rbufp->recv_time;
#ifdef DEBUG
if(debug) { /* Show \r as `R', other non-printing char as `?'. */
printf("arc: stamp -->%c<-- (%d chars rcvd)\n",
((c == '\r') ? 'R' : (isgraph((int)c) ? c : '?')),
rbufp->recv_length);
}
#endif
/*
Now correct timestamp by offset of last byte received---we
subtract from the receive time the delay implied by the
extra characters received.
Reject the input if the resulting code is too long, but
allow for the trailing \r, normally not used but a good
handle for tty_clk or somesuch kernel timestamper.
*/
if(arc_last_offset > LENARC) {
#ifdef ARCRON_DEBUG
if(debug) {
printf("arc: input code too long (%d cf %d); rejected.\n",
arc_last_offset, LENARC);
}
#endif
pp->lencode = 0;
refclock_report(peer, CEVNT_BADREPLY);
return;
}
L_SUBUF(&timestamp, charoffsets[arc_last_offset]);
#ifdef ARCRON_DEBUG
if(debug > 1) {
printf(
"arc: %s%d char(s) rcvd, the last for lastcode[%d]; -%sms offset applied.\n",
((rbufp->recv_length > 1) ? "*** " : ""),
rbufp->recv_length,
arc_last_offset,
mfptoms((unsigned long)0,
charoffsets[arc_last_offset],
1));
}
#endif
#ifdef ARCRON_MULTIPLE_SAMPLES
/*
If taking multiple samples, capture the current adjusted
sample iff:
* No timestamp has yet been captured (it is zero), OR
* This adjusted timestamp is earlier than the one already
captured, on the grounds that this one suffered less
delay in being delivered to us and is more accurate.
*/
if(L_ISZERO(&(up->lastrec)) ||
L_ISGEQ(&(up->lastrec), &timestamp))
#endif
{
#ifdef ARCRON_DEBUG
if(debug > 1) {
printf("arc: system timestamp captured.\n");
#ifdef ARCRON_MULTIPLE_SAMPLES
if(!L_ISZERO(&(up->lastrec))) {
l_fp diff;
diff = up->lastrec;
L_SUB(&diff, &timestamp);
printf("arc: adjusted timestamp by -%sms.\n",
mfptoms(diff.l_i, diff.l_f, 3));
}
#endif
}
#endif
up->lastrec = timestamp;
}
}
/* Just in case we still have lots of rubbish in the buffer... */
/* ...and to avoid the same timestamp being reused by mistake, */
/* eg on receipt of the \r coming in on its own after the */
/* timecode. */
if(pp->lencode >= LENARC) {
#ifdef ARCRON_DEBUG
if(debug && (rbufp->recv_buffer[0] != '\r'))
{ printf("arc: rubbish in pp->a_lastcode[].\n"); }
#endif
pp->lencode = 0;
return;
}
/* Append input to code buffer, avoiding overflow. */
for(i = 0; i < rbufp->recv_length; i++) {
if(pp->lencode >= LENARC) { break; } /* Avoid overflow... */
c = rbufp->recv_buffer[i];
/* Drop trailing '\r's and drop `h' command echo totally. */
if(c != '\r' && c != 'h') { pp->a_lastcode[pp->lencode++] = c; }
/*
If we've just put an `o' in the lastcode[0], clear the
timestamp in anticipation of a timecode arriving soon.
We would expect to get to process this before any of the
timecode arrives.
*/
if((c == 'o') && (pp->lencode == 1)) {
L_CLR(&(up->lastrec));
#ifdef ARCRON_DEBUG
if(debug > 1) { printf("arc: clearing timestamp.\n"); }
#endif
}
}
/* Handle a quality message. */
if(pp->a_lastcode[0] == 'g') {
int r, q;
if(pp->lencode < 3) { return; } /* Need more data... */
r = (pp->a_lastcode[1] & 0x7f); /* Strip parity. */
q = (pp->a_lastcode[2] & 0x7f); /* Strip parity. */
if(((q & 0x70) != 0x30) || ((q & 0xf) > MAX_CLOCK_QUALITY) ||
((r & 0x70) != 0x30)) {
/* Badly formatted response. */
#ifdef ARCRON_DEBUG
if(debug) { printf("arc: bad `g' response %2x %2x.\n", r, q); }
#endif
return;
}
if(r == '3') { /* Only use quality value whilst sync in progress. */
up->quality = (q & 0xf);
#ifdef DEBUG
if(debug) { printf("arc: signal quality %d.\n", up->quality); }
#endif
} else if( /* (r == '2') && */ up->resyncing) {
#ifdef DEBUG
if(debug)
{
printf("arc: sync finished, signal quality %d: %s\n",
up->quality,
quality_action(up->quality));
}
#endif
msyslog(LOG_NOTICE,
"ARCRON: sync finished, signal quality %d: %s",
up->quality,
quality_action(up->quality));
up->resyncing = 0; /* Resync is over. */
#ifdef ARCRON_KEEN
/* Clock quality dubious; resync earlier than usual. */
if((up->quality == QUALITY_UNKNOWN) ||
(up->quality < MIN_CLOCK_QUALITY_OK))
{ up->next_resync = current_time + RETRY_RESYNC_TIME; }
#endif
}
pp->lencode = 0;
return;
}
/* Stop now if this is not a timecode message. */
if(pp->a_lastcode[0] != 'o') {
pp->lencode = 0;
refclock_report(peer, CEVNT_BADREPLY);
return;
}
/* If we don't have enough data, wait for more... */
if(pp->lencode < LENARC) { return; }
/* WE HAVE NOW COLLECTED ONE TIMESTAMP (phew)... */
#ifdef ARCRON_DEBUG
if(debug > 1) { printf("arc: NOW HAVE TIMESTAMP...\n"); }
#endif
/* But check that we actually captured a system timestamp on it. */
if(L_ISZERO(&(up->lastrec))) {
#ifdef ARCRON_DEBUG
if(debug) { printf("arc: FAILED TO GET SYSTEM TIMESTAMP\n"); }
#endif
pp->lencode = 0;
refclock_report(peer, CEVNT_BADREPLY);
return;
}
/*
Append a mark of the clock's received signal quality for the
benefit of Derek Mulcahy's Tcl/Tk utility (we map the `unknown'
quality value to `6' for his s/w) and terminate the string for
sure. This should not go off the buffer end.
*/
pp->a_lastcode[pp->lencode] = ((up->quality == QUALITY_UNKNOWN) ?
'6' : ('0' + up->quality));
pp->a_lastcode[pp->lencode + 1] = '\0'; /* Terminate for printf(). */
record_clock_stats(&peer->srcadr, pp->a_lastcode);
/* We don't use the micro-/milli- second part... */
pp->usec = 0;
pp->msec = 0;
n = sscanf(pp->a_lastcode, "o%2d%2d%2d%1d%2d%2d%2d%1d%1d",
&pp->hour, &pp->minute, &pp->second,
&wday, &pp->day, &month, &pp->year, &bst, &status);
/* Validate format and numbers. */
if(n != 9) {
#ifdef ARCRON_DEBUG
/* Would expect to have caught major problems already... */
if(debug) { printf("arc: badly formatted data.\n"); }
#endif
refclock_report(peer, CEVNT_BADREPLY);
return;
}
/*
Validate received values at least enough to prevent internal
array-bounds problems, etc.
*/
if((pp->hour < 0) || (pp->hour > 23) ||
(pp->minute < 0) || (pp->minute > 59) ||
(pp->second < 0) || (pp->second > 60) /*Allow for leap seconds.*/ ||
(wday < 1) || (wday > 7) ||
(pp->day < 1) || (pp->day > 31) ||
(month < 1) || (month > 12) ||
(pp->year < 0) || (pp->year > 99)) {
/* Data out of range. */
refclock_report(peer, CEVNT_BADREPLY);
return;
}
/* Check that BST/UTC bits are the complement of one another. */
if(!(bst & 2) == !(bst & 4)) {
refclock_report(peer, CEVNT_BADREPLY);
return;
}
if(status & 0x8) { msyslog(LOG_NOTICE, "ARCRON: battery low"); }
/* Year-2000 alert! */
/* Attempt to wrap 2-digit date into sensible window. */
if(pp->year < YEAR_PIVOT) { pp->year += 100; } /* Y2KFixes */
pp->year += 1900; /* use full four-digit year */ /* Y2KFixes */
/*
Attempt to do the right thing by screaming that the code will
soon break when we get to the end of its useful life. What a
hero I am... PLEASE FIX LEAP-YEAR AND WRAP CODE IN 209X!
*/
if(pp->year >= YEAR_PIVOT+2000-2 ) { /* Y2KFixes */
/*This should get attention B^> */
msyslog(LOG_NOTICE,
"ARCRON: fix me! EITHER YOUR DATE IS BADLY WRONG or else I will break soon!");
}
#ifdef DEBUG
if(debug) {
printf("arc: n=%d %02d:%02d:%02d %02d/%02d/%04d %1d %1d\n",
n,
pp->hour, pp->minute, pp->second,
pp->day, month, pp->year, bst, status);
}
#endif
/*
The status value tested for is not strictly supported by the
clock spec since the value of bit 2 (0x4) is claimed to be
undefined for MSF, yet does seem to indicate if the last resync
was successful or not.
*/
pp->leap = LEAP_NOWARNING;
status &= 0x7;
if(status == 0x3) {
if(status != up->status)
{ msyslog(LOG_NOTICE, "ARCRON: signal acquired"); }
} else {
if(status != up->status) {
msyslog(LOG_NOTICE, "ARCRON: signal lost");
pp->leap = LEAP_NOTINSYNC; /* MSF clock is free-running. */
up->status = status;
refclock_report(peer, CEVNT_FAULT);
return;
}
}
up->status = status;
pp->day += moff[month - 1];
if(isleap_4(pp->year) && month > 2) { pp->day++; } /* Y2KFixes */
/* Convert to UTC if required */
if(bst & 2) {
pp->hour--;
if (pp->hour < 0) {
pp->hour = 23;
pp->day--;
/* If we try to wrap round the year (BST on 1st Jan), reject.*/
if(pp->day < 0) {
refclock_report(peer, CEVNT_BADTIME);
return;
}
}
}
/* If clock signal quality is unknown, revert to default PRECISION...*/
if(up->quality == QUALITY_UNKNOWN) { peer->precision = PRECISION; }
/* ...else improve precision if flag3 is set... */
else {
peer->precision = ((pp->sloppyclockflag & CLK_FLAG3) ?
HIGHPRECISION : PRECISION);
}
/* Notice and log any change (eg from initial defaults) for flags. */
if(up->saved_flags != pp->sloppyclockflag) {
#ifdef ARCRON_DEBUG
msyslog(LOG_NOTICE, "ARCRON: flags enabled: %s%s%s%s",
((pp->sloppyclockflag & CLK_FLAG1) ? "1" : "."),
((pp->sloppyclockflag & CLK_FLAG2) ? "2" : "."),
((pp->sloppyclockflag & CLK_FLAG3) ? "3" : "."),
((pp->sloppyclockflag & CLK_FLAG4) ? "4" : "."));
/* Note effects of flags changing... */
if(debug) {
printf("arc: CHOSENSAMPLES(pp) = %d.\n", CHOSENSAMPLES(pp));
printf("arc: NKEEP(pp) = %d.\n", NKEEP(pp));
printf("arc: PRECISION = %d.\n", peer->precision);
}
#endif
up->saved_flags = pp->sloppyclockflag;
}
/* Note time of last believable timestamp. */
pp->lastrec = up->lastrec;
#ifdef ARCRON_LEAPSECOND_KEEN
/* Find out if a leap-second might just have happened...
(ie is this the first hour of the first day of Jan or Jul?)
*/
if((pp->hour == 0) &&
(pp->day == 1) &&
((month == 1) || (month == 7))) {
if(possible_leap >= 0) {
/* A leap may have happened, and no resync has started yet...*/
possible_leap = 1;
}
} else {
/* Definitely not leap-second territory... */
possible_leap = 0;
}
#endif
if (!refclock_process(pp)) {
refclock_report(peer, CEVNT_BADTIME);
return;
}
refclock_receive(peer);
}
/* request_time() sends a time request to the clock with given peer. */
/* This automatically reports a fault if necessary. */
/* No data should be sent after this until arc_poll() returns. */
static void request_time P((int, struct peer *));
static void
request_time(
int unit,
struct peer *peer
)
{
struct refclockproc *pp = peer->procptr;
register struct arcunit *up = (struct arcunit *)pp->unitptr;
#ifdef DEBUG
if(debug) { printf("arc: unit %d: requesting time.\n", unit); }
#endif
if (!send_slow(up, pp->io.fd, "o\r")) {
#ifdef ARCRON_DEBUG
msyslog(LOG_NOTICE, "ARCRON: unit %d: problem sending", unit);
#endif
refclock_report(peer, CEVNT_FAULT);
return;
}
pp->polls++;
}
/*
* arc_poll - called by the transmit procedure
*/
static void
arc_poll(
int unit,
struct peer *peer
)
{
register struct arcunit *up;
struct refclockproc *pp;
int resync_needed; /* Should we start a resync? */
pp = peer->procptr;
up = (struct arcunit *)pp->unitptr;
pp->lencode = 0;
memset(pp->a_lastcode, 0, sizeof(pp->a_lastcode));
#if 0
/* Flush input. */
tcflush(pp->io.fd, TCIFLUSH);
#endif
/* Resync if our next scheduled resync time is here or has passed. */
resync_needed = (up->next_resync <= current_time);
#ifdef ARCRON_LEAPSECOND_KEEN
/*
Try to catch a potential leap-second insertion or deletion quickly.
In addition to the normal NTP fun of clocks that don't report
leap-seconds spooking their hosts, this clock does not even
sample the radio sugnal the whole time, so may miss a
leap-second insertion or deletion for up to a whole sample
time.
To try to minimise this effect, if in the first few minutes of
the day immediately following a leap-second-insertion point
(ie in the first hour of the first day of the first and sixth
months), and if the last resync was in the previous day, and a
resync is not already in progress, resync the clock
immediately.
*/
if((possible_leap > 0) && /* Must be 00:XX 01/0{1,7}/XXXX. */
(!up->resyncing)) { /* No resync in progress yet. */
resync_needed = 1;
possible_leap = -1; /* Prevent multiple resyncs. */
msyslog(LOG_NOTICE,"ARCRON: unit %d: checking for leap second",unit);
}
#endif
/* Do a resync if required... */
if(resync_needed) {
/* First, reset quality value to `unknown' so we can detect */
/* when a quality message has been responded to by this */
/* being set to some other value. */
up->quality = QUALITY_UNKNOWN;
/* Note that we are resyncing... */
up->resyncing = 1;
/* Now actually send the resync command and an immediate poll. */
#ifdef DEBUG
if(debug) { printf("arc: sending resync command (h\\r).\n"); }
#endif
msyslog(LOG_NOTICE, "ARCRON: unit %d: sending resync command", unit);
send_slow(up, pp->io.fd, "h\r");
/* Schedule our next resync... */
up->next_resync = current_time + DEFAULT_RESYNC_TIME;
/* Drop through to request time if appropriate. */
}
/* If clock quality is too poor to trust, indicate a fault. */
/* If quality is QUALITY_UNKNOWN and ARCRON_KEEN is defined,*/
/* we'll cross our fingers and just hope that the thing */
/* synced so quickly we did not catch it---we'll */
/* double-check the clock is OK elsewhere. */
if(
#ifdef ARCRON_KEEN
(up->quality != QUALITY_UNKNOWN) &&
#else
(up->quality == QUALITY_UNKNOWN) ||
#endif
(up->quality < MIN_CLOCK_QUALITY_OK)) {
#ifdef DEBUG
if(debug) {
printf("arc: clock quality %d too poor.\n", up->quality);
}
#endif
refclock_report(peer, CEVNT_FAULT);
return;
}
/* This is the normal case: request a timestamp. */
request_time(unit, peer);
}
#else
int refclock_arc_bs;
#endif