freebsd-dev/sys/mips/conf/WZR-HPAG300H.hints
Sean Bruno 040bcc9ac0 Switch is an 8316, so make the comments say that.
Delete extraneous comment line that manifested itself from cut-n-pasting.

Sponsored by:	Nicholas Esborn <nick@desert.net>
2014-12-03 23:37:23 +00:00

133 lines
3.4 KiB
Plaintext

# $FreeBSD$
# arge0 is connected to the LAN side of the switch PHY.
# arge1 is connected to the single port WAN side of the switch PHY.
hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x19000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0
hint.arge.0.phymask=0x0
hint.arge.0.media=1000
hint.arge.0.fduplex=1
hint.arge.0.eeprommac=0x1f05120c
hint.arge.0.mdio=mdioproxy0 # .. off of the switch mdiobus
hint.arge.0.miimode=3
hint.arge.1.phymask=0x10
hint.arge.1.media=1000
hint.arge.1.fduplex=1
hint.arge.1.eeprommac=0x1f05520c
hint.arge.1.mdio=mdioproxy1 # .. off of the switch mdiobus
hint.arge.1.miimode=3
#
# AR8316 switch config
#
hint.arswitch.0.at="mdio0"
hint.arswitch.0.is_7240=0 # We need to be explicitly told this
hint.arswitch.0.numphys=4 # 5 active switch PHYs (PHY 0 -> 4)
hint.arswitch.0.phy4cpu=1 # No, PHY 4 == dedicated PHY
hint.arswitch.0.is_rgmii=1 # Yes, is RGMII
hint.arswitch.0.is_gmii=0 # No, not GMII
# ath0 - slot 17
hint.pcib.0.bus.0.17.0.ath_fixup_addr=0x1f051000
hint.pcib.0.bus.0.17.0.ath_fixup_size=4096
# ath1 - slot 18
hint.pcib.0.bus.0.18.0.ath_fixup_addr=0x1f055000
hint.pcib.0.bus.0.18.0.ath_fixup_size=4096
# .. and now, telling each ath(4) NIC where to find the firmware
# image.
hint.ath.0.eeprom_firmware="pcib.0.bus.0.17.0.eeprom_firmware"
hint.ath.1.eeprom_firmware="pcib.0.bus.0.18.0.eeprom_firmware"
# Inherited from AR71XX_BASE.hints
#hint.mx25l.0.at="spibus0"
#hint.mx25l.0.cs=0
# This board has two 16 MB flash devices on difference Chip Select pins
hint.mx25l.1.at="spibus0"
hint.mx25l.1.cs=1
# Geom MAP
hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00040000
hint.map.0.name="uboot"
hint.map.0.readonly=1
hint.map.1.at="flash/spi0"
hint.map.1.start=0x00040000
hint.map.1.end=0x00050000
hint.map.1.name="u-boot-env"
hint.map.1.readonly=1
hint.map.2.at="flash/spi0"
hint.map.2.start=0x00050000
hint.map.2.end=0x00060000
hint.map.2.name="ART"
hint.map.2.readonly=1
# requires a 1M alignment and padding in the image.
# make sure you are using conv=sync and bs=1M in your dd
hint.map.3.at="flash/spi0"
hint.map.3.start=0x00060000
hint.map.3.end="search:0x00160000:0x100000:.!/bin/sh"
hint.map.3.name="kernel"
hint.map.3.readonly=1
hint.map.4.at="flash/spi0"
hint.map.4.start="search:0x00160000:0x100000:.!/bin/sh"
hint.map.4.end=0x01000000
hint.map.4.name="rootfs"
hint.map.4.readonly=1
hint.map.5.at="flash/spi1"
hint.map.5.start=0x00FF0000
hint.map.5.end=0x01000000
hint.map.5.name="cfg"
hint.map.5.readonly=0
# Pin 1 - SCK
# Pin 2 - SDA
# Pin 3 - usb
# Pin 4 -
# Pin 5 - aoss
# Pin 6 - router auto
# Pin 7 - router off
# Pin 8 - movie engine
# Pin 9 -
# Pin 10 -
# Pin 11 - reset button
# Pin 12 - CS0
# Pin 13 - CS1
# Pin 14 -
# Pin 15 -
# Pin 16 -
# Pin 17 -
# Don't flip on anything that isn't already enabled.
# Force on CS lines for flash devices, apparently this isn't done
# by uboot in normal booting. No idea why.
hint.gpio.0.function_set=0x00003004
hint.gpio.0.function_clear=0x00000000
# These are the GPIO LEDs and buttons which can be software controlled.
hint.gpio.0.pinmask=0x0001
hint.gpio.0.pinon=0x00000004
hint.gpioiic.0.at="gpiobus0"
#hint.gpioiic.0.pins=0x0003
hint.gpioiic.0.sda=0
hint.gpioiic.0.scl=1
# LEDs are configured separately and driven by the LED device
hint.gpioled.0.at="gpiobus0"
hint.gpioled.0.name="red-diag"
hint.gpioled.0.pins=0x0001