freebsd-dev/sys/dev/aic7xxx/aic7xxx_inline.h
Justin T. Gibbs 8f214efc9a Major update to the aic7xxx driver:
ahc_eisa.c:
ahc_pci.c:
	Conform to new aic7xxx IRQ API.

	Adapt to aic7xxx_freebsd -> aic7xxx_osm changes.

aic7770.c:
	Disable card generated interrupt early in our probe for
	"extra safety"

	Commonize some seeprom code with the PCI side of the driver.

aic7xxx.c:
	Correctly initialize a few scratch ram locations during
	a sequencer restart.  This avoids spurious sequencer ram
	parity errors in some configurations.

	Include the softc in ahc_update_residual calls.  We need it
	for some diagnostics in this code path.

	Flag a data overrun on an auto-request sense failure as a
	CAM_AUTOSENSE_FAIL rather than a CAM_DATA_RUN_ERR.

	Force a renegotiation after noticing a parity error.  This
	covers targets that lose our negotiation settings but don't
	bother to give us a unit attention condition.  This can happen
	if a target fails during a reselection of us during a cable
	pull.

	Convert some code to using constants.

	Fix some typos.

	Correct target mode message loop handling.  ahc_clear_msg_state
	was not clearing the "need to go to message out phase" bit once
	our loop was over.

	Simplify some abort handling code.

	Include tag information in target mode immediate notify events.

	When shutting down EISA controllers, don't EISA BIOS settings in
	the high portions of scratch ram.  This fixes warm boot issues on
	some systems.

	Save a bit of space by only allocating the SCBs that we can use.

	Avoid some code paths in ahc_abort_scbs() if we are currently
	acting as a target.

	Correctly cleanup stranded SCBs in the card's SCB array.  These
	are SCBs who's mapping has already been torn down by code that
	aborted the SCB by seeing it in another list first.

	Add a comment about some potential bus reset issues for target
	mode on Twin (EISA only) controllers.

aic7xxx.h:
	Cleanup the hardware scb definitions a bit.

	Allocate a ful 256 byte scb mapping index.  This simplifies
	the lookup code since the table covers all possible (and potentially
	bogus) values.

	Make AHC_DEBUG work again.

aic7xxx.reg:
	Updates to hardware SCB definition.

	New definitions for target mode fixes.

aic7xxx.seq:
	In target mode, initialize SAVED_LUN just after we receive
	the identify message.  It may be required in the error recovery
	path when a normal cdb packet (includes lun) is not sent up to
	the host for processing.

	Respond to irregular messages during a selection in target mode.

	Defer looking for space for a cdb packet until we are about to
	enter command phase.  We want to be able to handle irregular messages
	even if we would otherwise return QUEUE_FULL or BUSY.

	Add support for sending Ignore Wide Residue messages as a target.

	In the disable disconnect case in target mode, set our transfer
	rate correctly once data are availble.

aic7xxx_93cx6.c:
aic7xxx_93cx6.h:
	Add the ability to write and erase the seeprom.

aic7xxx_inline.h:
	Correct Big Endian handling of large cdb sizes (> 12 bytes).

	Adaptec to changes in the calc_residual API.

	Correct a target mode bug where we always attempted to service
	the input queue even if no progress could be made due to lack
	of ATIOs.

aic7xxx_osm.c:
	Adaptec to new IRQ mapping API.  The new API allows the core
	to only enable our IRQ mapping once it is safe (sufficient
	initialization) to do so.

	Slap bootverbose protection around some diagnostics.

	Only attempt DT phases if we are wide.

aic7xxx_osm.h:
	Enable big endian support.

	Adjust for IRQ API change.

aic7xxx_pci.c:
	Be more careful about relying on subvendor 9005 information.
	We now only trust it for HBAs.  This should allow the driver
	to attach to some MBs where the subvendor/device information
	does not follow the Adaptec spec.

	Only enable interrupts on the card once we are fully setup.

	Disable external SCB ram usage on the aic7895.  I have not
	been able to make it 100% reliable.

	Adjust to seeprom routines being properly prefixed with "ahc".

	Fix a few bugs in the external SCB ram probing routine.  We
	need to clear any parity errors we've triggered during the
	probe to avoid future, fatal, interrupts.

	If we detect an invalid cable combination, pretent there are
	no cable at all.  This will enable all of the terminators
	which is probably the safest configuration we can "guess".

MFC after: 4 days
2002-04-24 16:58:51 +00:00

564 lines
16 KiB
C

/*
* Inline routines shareable across OS platforms.
*
* Copyright (c) 1994-2001 Justin T. Gibbs.
* Copyright (c) 2000-2001 Adaptec Inc.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/aic7xxx/aic7xxx_inline.h#33 $
*
* $FreeBSD$
*/
#ifndef _AIC7XXX_INLINE_H_
#define _AIC7XXX_INLINE_H_
/************************* Sequencer Execution Control ************************/
static __inline void ahc_pause_bug_fix(struct ahc_softc *ahc);
static __inline int ahc_is_paused(struct ahc_softc *ahc);
static __inline void ahc_pause(struct ahc_softc *ahc);
static __inline void ahc_unpause(struct ahc_softc *ahc);
/*
* Work around any chip bugs related to halting sequencer execution.
* On Ultra2 controllers, we must clear the CIOBUS stretch signal by
* reading a register that will set this signal and deassert it.
* Without this workaround, if the chip is paused, by an interrupt or
* manual pause while accessing scb ram, accesses to certain registers
* will hang the system (infinite pci retries).
*/
static __inline void
ahc_pause_bug_fix(struct ahc_softc *ahc)
{
if ((ahc->features & AHC_ULTRA2) != 0)
(void)ahc_inb(ahc, CCSCBCTL);
}
/*
* Determine whether the sequencer has halted code execution.
* Returns non-zero status if the sequencer is stopped.
*/
static __inline int
ahc_is_paused(struct ahc_softc *ahc)
{
return ((ahc_inb(ahc, HCNTRL) & PAUSE) != 0);
}
/*
* Request that the sequencer stop and wait, indefinitely, for it
* to stop. The sequencer will only acknowledge that it is paused
* once it has reached an instruction boundary and PAUSEDIS is
* cleared in the SEQCTL register. The sequencer may use PAUSEDIS
* for critical sections.
*/
static __inline void
ahc_pause(struct ahc_softc *ahc)
{
ahc_outb(ahc, HCNTRL, ahc->pause);
/*
* Since the sequencer can disable pausing in a critical section, we
* must loop until it actually stops.
*/
while (ahc_is_paused(ahc) == 0)
;
ahc_pause_bug_fix(ahc);
}
/*
* Allow the sequencer to continue program execution.
* We check here to ensure that no additional interrupt
* sources that would cause the sequencer to halt have been
* asserted. If, for example, a SCSI bus reset is detected
* while we are fielding a different, pausing, interrupt type,
* we don't want to release the sequencer before going back
* into our interrupt handler and dealing with this new
* condition.
*/
static __inline void
ahc_unpause(struct ahc_softc *ahc)
{
if ((ahc_inb(ahc, INTSTAT) & (SCSIINT | SEQINT | BRKADRINT)) == 0)
ahc_outb(ahc, HCNTRL, ahc->unpause);
}
/*********************** Untagged Transaction Routines ************************/
static __inline void ahc_freeze_untagged_queues(struct ahc_softc *ahc);
static __inline void ahc_release_untagged_queues(struct ahc_softc *ahc);
/*
* Block our completion routine from starting the next untagged
* transaction for this target or target lun.
*/
static __inline void
ahc_freeze_untagged_queues(struct ahc_softc *ahc)
{
if ((ahc->flags & AHC_SCB_BTT) == 0)
ahc->untagged_queue_lock++;
}
/*
* Allow the next untagged transaction for this target or target lun
* to be executed. We use a counting semaphore to allow the lock
* to be acquired recursively. Once the count drops to zero, the
* transaction queues will be run.
*/
static __inline void
ahc_release_untagged_queues(struct ahc_softc *ahc)
{
if ((ahc->flags & AHC_SCB_BTT) == 0) {
ahc->untagged_queue_lock--;
if (ahc->untagged_queue_lock == 0)
ahc_run_untagged_queues(ahc);
}
}
/************************** Memory mapping routines ***************************/
static __inline struct ahc_dma_seg *
ahc_sg_bus_to_virt(struct scb *scb,
uint32_t sg_busaddr);
static __inline uint32_t
ahc_sg_virt_to_bus(struct scb *scb,
struct ahc_dma_seg *sg);
static __inline uint32_t
ahc_hscb_busaddr(struct ahc_softc *ahc, u_int index);
static __inline void ahc_sync_scb(struct ahc_softc *ahc,
struct scb *scb, int op);
static __inline void ahc_sync_sglist(struct ahc_softc *ahc,
struct scb *scb, int op);
static __inline uint32_t
ahc_targetcmd_offset(struct ahc_softc *ahc,
u_int index);
static __inline struct ahc_dma_seg *
ahc_sg_bus_to_virt(struct scb *scb, uint32_t sg_busaddr)
{
int sg_index;
sg_index = (sg_busaddr - scb->sg_list_phys)/sizeof(struct ahc_dma_seg);
/* sg_list_phys points to entry 1, not 0 */
sg_index++;
return (&scb->sg_list[sg_index]);
}
static __inline uint32_t
ahc_sg_virt_to_bus(struct scb *scb, struct ahc_dma_seg *sg)
{
int sg_index;
/* sg_list_phys points to entry 1, not 0 */
sg_index = sg - &scb->sg_list[1];
return (scb->sg_list_phys + (sg_index * sizeof(*scb->sg_list)));
}
static __inline uint32_t
ahc_hscb_busaddr(struct ahc_softc *ahc, u_int index)
{
return (ahc->scb_data->hscb_busaddr
+ (sizeof(struct hardware_scb) * index));
}
static __inline void
ahc_sync_scb(struct ahc_softc *ahc, struct scb *scb, int op)
{
ahc_dmamap_sync(ahc, ahc->scb_data->hscb_dmat,
ahc->scb_data->hscb_dmamap,
/*offset*/(scb->hscb - ahc->hscbs) * sizeof(*scb->hscb),
/*len*/sizeof(*scb->hscb), op);
}
static __inline void
ahc_sync_sglist(struct ahc_softc *ahc, struct scb *scb, int op)
{
if (scb->sg_count == 0)
return;
ahc_dmamap_sync(ahc, ahc->scb_data->sg_dmat, scb->sg_map->sg_dmamap,
/*offset*/(scb->sg_list - scb->sg_map->sg_vaddr)
* sizeof(struct ahc_dma_seg),
/*len*/sizeof(struct ahc_dma_seg) * scb->sg_count, op);
}
static __inline uint32_t
ahc_targetcmd_offset(struct ahc_softc *ahc, u_int index)
{
return (((uint8_t *)&ahc->targetcmds[index]) - ahc->qoutfifo);
}
/******************************** Debugging ***********************************/
static __inline char *ahc_name(struct ahc_softc *ahc);
static __inline char *
ahc_name(struct ahc_softc *ahc)
{
return (ahc->name);
}
/*********************** Miscelaneous Support Functions ***********************/
static __inline void ahc_update_residual(struct ahc_softc *ahc,
struct scb *scb);
static __inline struct ahc_initiator_tinfo *
ahc_fetch_transinfo(struct ahc_softc *ahc,
char channel, u_int our_id,
u_int remote_id,
struct ahc_tmode_tstate **tstate);
static __inline struct scb*
ahc_get_scb(struct ahc_softc *ahc);
static __inline void ahc_free_scb(struct ahc_softc *ahc, struct scb *scb);
static __inline void ahc_swap_with_next_hscb(struct ahc_softc *ahc,
struct scb *scb);
static __inline void ahc_queue_scb(struct ahc_softc *ahc, struct scb *scb);
static __inline struct scsi_sense_data *
ahc_get_sense_buf(struct ahc_softc *ahc,
struct scb *scb);
static __inline uint32_t
ahc_get_sense_bufaddr(struct ahc_softc *ahc,
struct scb *scb);
/*
* Determine whether the sequencer reported a residual
* for this SCB/transaction.
*/
static __inline void
ahc_update_residual(struct ahc_softc *ahc, struct scb *scb)
{
uint32_t sgptr;
sgptr = ahc_le32toh(scb->hscb->sgptr);
if ((sgptr & SG_RESID_VALID) != 0)
ahc_calc_residual(ahc, scb);
}
/*
* Return pointers to the transfer negotiation information
* for the specified our_id/remote_id pair.
*/
static __inline struct ahc_initiator_tinfo *
ahc_fetch_transinfo(struct ahc_softc *ahc, char channel, u_int our_id,
u_int remote_id, struct ahc_tmode_tstate **tstate)
{
/*
* Transfer data structures are stored from the perspective
* of the target role. Since the parameters for a connection
* in the initiator role to a given target are the same as
* when the roles are reversed, we pretend we are the target.
*/
if (channel == 'B')
our_id += 8;
*tstate = ahc->enabled_targets[our_id];
return (&(*tstate)->transinfo[remote_id]);
}
/*
* Get a free scb. If there are none, see if we can allocate a new SCB.
*/
static __inline struct scb *
ahc_get_scb(struct ahc_softc *ahc)
{
struct scb *scb;
if ((scb = SLIST_FIRST(&ahc->scb_data->free_scbs)) == NULL) {
ahc_alloc_scbs(ahc);
scb = SLIST_FIRST(&ahc->scb_data->free_scbs);
if (scb == NULL)
return (NULL);
}
SLIST_REMOVE_HEAD(&ahc->scb_data->free_scbs, links.sle);
return (scb);
}
/*
* Return an SCB resource to the free list.
*/
static __inline void
ahc_free_scb(struct ahc_softc *ahc, struct scb *scb)
{
struct hardware_scb *hscb;
hscb = scb->hscb;
/* Clean up for the next user */
ahc->scb_data->scbindex[hscb->tag] = NULL;
scb->flags = SCB_FREE;
hscb->control = 0;
SLIST_INSERT_HEAD(&ahc->scb_data->free_scbs, scb, links.sle);
/* Notify the OSM that a resource is now available. */
ahc_platform_scb_free(ahc, scb);
}
static __inline struct scb *
ahc_lookup_scb(struct ahc_softc *ahc, u_int tag)
{
struct scb* scb;
scb = ahc->scb_data->scbindex[tag];
if (scb != NULL)
ahc_sync_scb(ahc, scb,
BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE);
return (scb);
}
static __inline void
ahc_swap_with_next_hscb(struct ahc_softc *ahc, struct scb *scb)
{
struct hardware_scb *q_hscb;
u_int saved_tag;
/*
* Our queuing method is a bit tricky. The card
* knows in advance which HSCB to download, and we
* can't disappoint it. To achieve this, the next
* SCB to download is saved off in ahc->next_queued_scb.
* When we are called to queue "an arbitrary scb",
* we copy the contents of the incoming HSCB to the one
* the sequencer knows about, swap HSCB pointers and
* finally assign the SCB to the tag indexed location
* in the scb_array. This makes sure that we can still
* locate the correct SCB by SCB_TAG.
*/
q_hscb = ahc->next_queued_scb->hscb;
saved_tag = q_hscb->tag;
memcpy(q_hscb, scb->hscb, sizeof(*scb->hscb));
if ((scb->flags & SCB_CDB32_PTR) != 0) {
q_hscb->shared_data.cdb_ptr =
ahc_htole32(ahc_hscb_busaddr(ahc, q_hscb->tag)
+ offsetof(struct hardware_scb, cdb32));
}
q_hscb->tag = saved_tag;
q_hscb->next = scb->hscb->tag;
/* Now swap HSCB pointers. */
ahc->next_queued_scb->hscb = scb->hscb;
scb->hscb = q_hscb;
/* Now define the mapping from tag to SCB in the scbindex */
ahc->scb_data->scbindex[scb->hscb->tag] = scb;
}
/*
* Tell the sequencer about a new transaction to execute.
*/
static __inline void
ahc_queue_scb(struct ahc_softc *ahc, struct scb *scb)
{
ahc_swap_with_next_hscb(ahc, scb);
if (scb->hscb->tag == SCB_LIST_NULL
|| scb->hscb->next == SCB_LIST_NULL)
panic("Attempt to queue invalid SCB tag %x:%x\n",
scb->hscb->tag, scb->hscb->next);
/*
* Keep a history of SCBs we've downloaded in the qinfifo.
*/
ahc->qinfifo[ahc->qinfifonext++] = scb->hscb->tag;
/*
* Make sure our data is consistant from the
* perspective of the adapter.
*/
ahc_sync_scb(ahc, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE);
/* Tell the adapter about the newly queued SCB */
if ((ahc->features & AHC_QUEUE_REGS) != 0) {
ahc_outb(ahc, HNSCB_QOFF, ahc->qinfifonext);
} else {
if ((ahc->features & AHC_AUTOPAUSE) == 0)
ahc_pause(ahc);
ahc_outb(ahc, KERNEL_QINPOS, ahc->qinfifonext);
if ((ahc->features & AHC_AUTOPAUSE) == 0)
ahc_unpause(ahc);
}
}
static __inline struct scsi_sense_data *
ahc_get_sense_buf(struct ahc_softc *ahc, struct scb *scb)
{
int offset;
offset = scb - ahc->scb_data->scbarray;
return (&ahc->scb_data->sense[offset]);
}
static __inline uint32_t
ahc_get_sense_bufaddr(struct ahc_softc *ahc, struct scb *scb)
{
int offset;
offset = scb - ahc->scb_data->scbarray;
return (ahc->scb_data->sense_busaddr
+ (offset * sizeof(struct scsi_sense_data)));
}
/************************** Interrupt Processing ******************************/
static __inline void ahc_sync_qoutfifo(struct ahc_softc *ahc, int op);
static __inline void ahc_sync_tqinfifo(struct ahc_softc *ahc, int op);
static __inline u_int ahc_check_cmdcmpltqueues(struct ahc_softc *ahc);
static __inline void ahc_intr(struct ahc_softc *ahc);
static __inline void
ahc_sync_qoutfifo(struct ahc_softc *ahc, int op)
{
ahc_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap,
/*offset*/0, /*len*/256, op);
}
static __inline void
ahc_sync_tqinfifo(struct ahc_softc *ahc, int op)
{
#ifdef AHC_TARGET_MODE
if ((ahc->flags & AHC_TARGETROLE) != 0) {
ahc_dmamap_sync(ahc, ahc->shared_data_dmat,
ahc->shared_data_dmamap,
ahc_targetcmd_offset(ahc, 0),
sizeof(struct target_cmd) * AHC_TMODE_CMDS,
op);
}
#endif
}
/*
* See if the firmware has posted any completed commands
* into our in-core command complete fifos.
*/
#define AHC_RUN_QOUTFIFO 0x1
#define AHC_RUN_TQINFIFO 0x2
static __inline u_int
ahc_check_cmdcmpltqueues(struct ahc_softc *ahc)
{
u_int retval;
retval = 0;
ahc_dmamap_sync(ahc, ahc->shared_data_dmat, ahc->shared_data_dmamap,
/*offset*/ahc->qoutfifonext, /*len*/1,
BUS_DMASYNC_POSTREAD);
if (ahc->qoutfifo[ahc->qoutfifonext] != SCB_LIST_NULL)
retval |= AHC_RUN_QOUTFIFO;
#ifdef AHC_TARGET_MODE
if ((ahc->flags & AHC_TARGETROLE) != 0
&& (ahc->flags & AHC_TQINFIFO_BLOCKED) == 0) {
ahc_dmamap_sync(ahc, ahc->shared_data_dmat,
ahc->shared_data_dmamap,
ahc_targetcmd_offset(ahc, ahc->tqinfifofnext),
/*len*/sizeof(struct target_cmd),
BUS_DMASYNC_POSTREAD);
if (ahc->targetcmds[ahc->tqinfifonext].cmd_valid != 0)
retval |= AHC_RUN_TQINFIFO;
}
#endif
return (retval);
}
/*
* Catch an interrupt from the adapter
*/
static __inline void
ahc_intr(struct ahc_softc *ahc)
{
u_int intstat;
/*
* Instead of directly reading the interrupt status register,
* infer the cause of the interrupt by checking our in-core
* completion queues. This avoids a costly PCI bus read in
* most cases.
*/
if ((ahc->flags & (AHC_ALL_INTERRUPTS|AHC_EDGE_INTERRUPT)) == 0
&& (ahc_check_cmdcmpltqueues(ahc) != 0))
intstat = CMDCMPLT;
else {
intstat = ahc_inb(ahc, INTSTAT);
}
if (intstat & CMDCMPLT) {
ahc_outb(ahc, CLRINT, CLRCMDINT);
/*
* Ensure that the chip sees that we've cleared
* this interrupt before we walk the output fifo.
* Otherwise, we may, due to posted bus writes,
* clear the interrupt after we finish the scan,
* and after the sequencer has added new entries
* and asserted the interrupt again.
*/
ahc_flush_device_writes(ahc);
ahc_run_qoutfifo(ahc);
#ifdef AHC_TARGET_MODE
if ((ahc->flags & AHC_TARGETROLE) != 0)
ahc_run_tqinfifo(ahc, /*paused*/FALSE);
#endif
}
if (intstat == 0xFF && (ahc->features & AHC_REMOVABLE) != 0)
/* Hot eject */
return;
if ((intstat & INT_PEND) == 0) {
#if AHC_PCI_CONFIG > 0
if (ahc->unsolicited_ints > 500) {
ahc->unsolicited_ints = 0;
if ((ahc->chip & AHC_PCI) != 0
&& (ahc_inb(ahc, ERROR) & PCIERRSTAT) != 0)
ahc->bus_intr(ahc);
}
#endif
ahc->unsolicited_ints++;
return;
}
ahc->unsolicited_ints = 0;
if (intstat & BRKADRINT) {
ahc_handle_brkadrint(ahc);
/* Fatal error, no more interrupts to handle. */
return;
}
if ((intstat & (SEQINT|SCSIINT)) != 0)
ahc_pause_bug_fix(ahc);
if ((intstat & SEQINT) != 0)
ahc_handle_seqint(ahc, intstat);
if ((intstat & SCSIINT) != 0)
ahc_handle_scsiint(ahc, intstat);
}
#endif /* _AIC7XXX_INLINE_H_ */