c37904e8ba
and start teaching subsystems about it. The Atheros MIPS platforms don't guarantee any kind of FIFO consistency with interrupts in hardware. So software needs to do a flush when it receives an interrupt and before it calls the interrupt handler. There are new ones for the QCA934x and QCA955x, so do a few things: * Get rid of the individual ones (for ethernet and IP2); * Create a mux and enum listing all the variations on DDR flushes; * replace the uses of IP2 with the relevant one (which will typically be "PCI" here); * call the USB DDR flush before calling the real USB interrupt handlers; * call the ethernet one upon receiving an interrupt that's for us, rather than never calling it during operation. Tested: * QCA9558 (TP-Link archer c7 v2) * AR9331 (Carambola 2) TODO: * PCI, USB, ethernet, etc need to do a double-check to see if the interrupt was truely for them before doing the DDR. For now I prefer "correct" over "fast".
357 lines
8.9 KiB
C
357 lines
8.9 KiB
C
/*-
|
|
* Copyright (c) 2012 Adrian Chadd <adrian@FreeBSD.org>
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
#include <sys/cdefs.h>
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
#include "opt_ddb.h"
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/conf.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/cons.h>
|
|
#include <sys/kdb.h>
|
|
#include <sys/reboot.h>
|
|
|
|
#include <vm/vm.h>
|
|
#include <vm/vm_page.h>
|
|
|
|
#include <net/ethernet.h>
|
|
|
|
#include <machine/clock.h>
|
|
#include <machine/cpu.h>
|
|
#include <machine/cpuregs.h>
|
|
#include <machine/hwfunc.h>
|
|
#include <machine/md_var.h>
|
|
#include <machine/trap.h>
|
|
#include <machine/vmparam.h>
|
|
|
|
#include <mips/atheros/ar71xxreg.h>
|
|
#include <mips/atheros/ar933xreg.h>
|
|
|
|
#include <mips/atheros/ar71xx_cpudef.h>
|
|
#include <mips/atheros/ar71xx_setup.h>
|
|
|
|
#include <mips/atheros/ar71xx_chip.h>
|
|
#include <mips/atheros/ar933x_chip.h>
|
|
|
|
static void
|
|
ar933x_chip_detect_mem_size(void)
|
|
{
|
|
}
|
|
|
|
static void
|
|
ar933x_chip_detect_sys_frequency(void)
|
|
{
|
|
uint32_t clock_ctrl;
|
|
uint32_t cpu_config;
|
|
uint32_t freq;
|
|
uint32_t t;
|
|
|
|
t = ATH_READ_REG(AR933X_RESET_REG_BOOTSTRAP);
|
|
if (t & AR933X_BOOTSTRAP_REF_CLK_40)
|
|
u_ar71xx_refclk = (40 * 1000 * 1000);
|
|
else
|
|
u_ar71xx_refclk = (25 * 1000 * 1000);
|
|
|
|
clock_ctrl = ATH_READ_REG(AR933X_PLL_CLOCK_CTRL_REG);
|
|
if (clock_ctrl & AR933X_PLL_CLOCK_CTRL_BYPASS) {
|
|
u_ar71xx_cpu_freq = u_ar71xx_refclk;
|
|
u_ar71xx_ahb_freq = u_ar71xx_refclk;
|
|
u_ar71xx_ddr_freq = u_ar71xx_refclk;
|
|
} else {
|
|
cpu_config = ATH_READ_REG(AR933X_PLL_CPU_CONFIG_REG);
|
|
|
|
t = (cpu_config >> AR933X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
|
|
AR933X_PLL_CPU_CONFIG_REFDIV_MASK;
|
|
freq = u_ar71xx_refclk / t;
|
|
|
|
t = (cpu_config >> AR933X_PLL_CPU_CONFIG_NINT_SHIFT) &
|
|
AR933X_PLL_CPU_CONFIG_NINT_MASK;
|
|
freq *= t;
|
|
|
|
t = (cpu_config >> AR933X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
|
|
AR933X_PLL_CPU_CONFIG_OUTDIV_MASK;
|
|
if (t == 0)
|
|
t = 1;
|
|
|
|
freq >>= t;
|
|
|
|
t = ((clock_ctrl >> AR933X_PLL_CLOCK_CTRL_CPU_DIV_SHIFT) &
|
|
AR933X_PLL_CLOCK_CTRL_CPU_DIV_MASK) + 1;
|
|
u_ar71xx_cpu_freq = freq / t;
|
|
|
|
t = ((clock_ctrl >> AR933X_PLL_CLOCK_CTRL_DDR_DIV_SHIFT) &
|
|
AR933X_PLL_CLOCK_CTRL_DDR_DIV_MASK) + 1;
|
|
u_ar71xx_ddr_freq = freq / t;
|
|
|
|
t = ((clock_ctrl >> AR933X_PLL_CLOCK_CTRL_AHB_DIV_SHIFT) &
|
|
AR933X_PLL_CLOCK_CTRL_AHB_DIV_MASK) + 1;
|
|
u_ar71xx_ahb_freq = freq / t;
|
|
}
|
|
|
|
/*
|
|
* On the AR933x, the UART frequency is the reference clock,
|
|
* not the AHB bus clock.
|
|
*/
|
|
u_ar71xx_uart_freq = u_ar71xx_refclk;
|
|
|
|
/*
|
|
* XXX TODO: check whether the mdio frequency is always the
|
|
* refclock frequency, or whether it's variable like on the
|
|
* AR934x.
|
|
*/
|
|
u_ar71xx_mdio_freq = u_ar71xx_refclk;
|
|
|
|
/*
|
|
* XXX check what the watchdog frequency should be?
|
|
*/
|
|
u_ar71xx_wdt_freq = u_ar71xx_ahb_freq;
|
|
}
|
|
|
|
static void
|
|
ar933x_chip_device_stop(uint32_t mask)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR933X_RESET_REG_RESET_MODULE);
|
|
ATH_WRITE_REG(AR933X_RESET_REG_RESET_MODULE, reg | mask);
|
|
}
|
|
|
|
static void
|
|
ar933x_chip_device_start(uint32_t mask)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR933X_RESET_REG_RESET_MODULE);
|
|
ATH_WRITE_REG(AR933X_RESET_REG_RESET_MODULE, reg & ~mask);
|
|
}
|
|
|
|
static int
|
|
ar933x_chip_device_stopped(uint32_t mask)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR933X_RESET_REG_RESET_MODULE);
|
|
return ((reg & mask) == mask);
|
|
}
|
|
|
|
static void
|
|
ar933x_chip_set_mii_speed(uint32_t unit, uint32_t speed)
|
|
{
|
|
|
|
/* XXX TODO */
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* XXX TODO !!
|
|
*/
|
|
static void
|
|
ar933x_chip_set_pll_ge(int unit, int speed, uint32_t pll)
|
|
{
|
|
|
|
switch (unit) {
|
|
case 0:
|
|
/* XXX TODO */
|
|
break;
|
|
case 1:
|
|
/* XXX TODO */
|
|
break;
|
|
default:
|
|
printf("%s: invalid PLL set for arge unit: %d\n",
|
|
__func__, unit);
|
|
return;
|
|
}
|
|
}
|
|
|
|
static void
|
|
ar933x_chip_ddr_flush(ar71xx_flush_ddr_id_t id)
|
|
{
|
|
|
|
switch (id) {
|
|
case AR71XX_CPU_DDR_FLUSH_GE0:
|
|
ar71xx_ddr_flush(AR933X_DDR_REG_FLUSH_GE0);
|
|
break;
|
|
case AR71XX_CPU_DDR_FLUSH_GE1:
|
|
ar71xx_ddr_flush(AR933X_DDR_REG_FLUSH_GE1);
|
|
break;
|
|
case AR71XX_CPU_DDR_FLUSH_USB:
|
|
ar71xx_ddr_flush(AR933X_DDR_REG_FLUSH_USB);
|
|
break;
|
|
case AR71XX_CPU_DDR_FLUSH_WMAC:
|
|
ar71xx_ddr_flush(AR933X_DDR_REG_FLUSH_WMAC);
|
|
break;
|
|
default:
|
|
printf("%s: invalid DDR flush id (%d)\n", __func__, id);
|
|
break;
|
|
}
|
|
}
|
|
|
|
|
|
static uint32_t
|
|
ar933x_chip_get_eth_pll(unsigned int mac, int speed)
|
|
{
|
|
uint32_t pll;
|
|
|
|
switch (speed) {
|
|
case 10:
|
|
pll = AR933X_PLL_VAL_10;
|
|
break;
|
|
case 100:
|
|
pll = AR933X_PLL_VAL_100;
|
|
break;
|
|
case 1000:
|
|
pll = AR933X_PLL_VAL_1000;
|
|
break;
|
|
default:
|
|
printf("%s%d: invalid speed %d\n", __func__, mac, speed);
|
|
pll = 0;
|
|
}
|
|
return (pll);
|
|
}
|
|
|
|
static void
|
|
ar933x_chip_init_usb_peripheral(void)
|
|
{
|
|
ar71xx_device_stop(AR933X_RESET_USBSUS_OVERRIDE);
|
|
DELAY(100);
|
|
|
|
ar71xx_device_start(AR933X_RESET_USB_HOST);
|
|
DELAY(100);
|
|
|
|
ar71xx_device_start(AR933X_RESET_USB_PHY);
|
|
DELAY(100);
|
|
}
|
|
|
|
static void
|
|
ar933x_configure_gmac(uint32_t gmac_cfg)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = ATH_READ_REG(AR933X_GMAC_REG_ETH_CFG);
|
|
|
|
/*
|
|
* The relevant bits here include:
|
|
*
|
|
* + AR933X_ETH_CFG_SW_PHY_SWAP
|
|
* + AR933X_ETH_CFG_SW_PHY_ADDR_SWAP
|
|
*
|
|
* There are other things; look at what openwrt exposes so
|
|
* it can be correctly exposed.
|
|
*
|
|
* TODO: what about ethernet switch support? How's that work?
|
|
*/
|
|
if (bootverbose)
|
|
printf("%s: GMAC config was 0x%08x\n", __func__, reg);
|
|
reg &= ~(AR933X_ETH_CFG_SW_PHY_SWAP | AR933X_ETH_CFG_SW_PHY_ADDR_SWAP);
|
|
reg |= gmac_cfg;
|
|
if (bootverbose)
|
|
printf("%s: GMAC setting is 0x%08x; register is now 0x%08x\n",
|
|
__func__,
|
|
gmac_cfg,
|
|
reg);
|
|
ATH_WRITE_REG(AR933X_GMAC_REG_ETH_CFG, reg);
|
|
}
|
|
|
|
static void
|
|
ar933x_chip_init_gmac(void)
|
|
{
|
|
int val;
|
|
uint32_t gmac_cfg = 0;
|
|
|
|
/*
|
|
* These two bits need a bit better explanation.
|
|
*
|
|
* The default configuration in the hardware is to map both
|
|
* ports to the internal switch.
|
|
*
|
|
* Here, GE0 == arge0, GE1 == arge1.
|
|
*
|
|
* The internal switch has:
|
|
* + 5 MAC ports, MAC0->MAC4.
|
|
* + 5 PHY ports, PHY0->PHY4,
|
|
* + MAC0 connects to GE1;
|
|
* + GE0 connects to PHY4;
|
|
* + The other mappings are MAC1->PHY0, MAC2->PHY1 .. MAC4->PHY3.
|
|
*
|
|
* The GE1 port is linked in via 1000MBit/full, supplying what is
|
|
* normally the 'WAN' switch ports.
|
|
*
|
|
* The switch is connected the MDIO bus on GE1. It looks like
|
|
* a normal AR7240 on-board switch.
|
|
*
|
|
* The GE0 port is connected via MII to PHY4, and can operate in
|
|
* 10/100mbit, full/half duplex. Ie, you can speak to PHY4 on
|
|
* the MDIO bus and everything will simply 'work'.
|
|
*
|
|
* So far so good. This looks just like an AR7240 SoC.
|
|
*
|
|
* However, some configurations will just expose one or two
|
|
* physical ports. In this case, some configuration bits can
|
|
* be set to tweak this.
|
|
*
|
|
* + CFG_SW_PHY_ADDR_SWAP swaps PHY port 0 with PHY port 4.
|
|
* Ie, GE0's PHY shows up as PHY 0. So if there's only
|
|
* one physical port, there's no need to involve the
|
|
* switch framework - it can just show up as a default,
|
|
* normal single PHY.
|
|
*
|
|
* + CFG_SW_PHY_SWAP swaps the internal switch connection
|
|
* between PHY0 and PHY4. Ie, PHY4 connects to MAc1,
|
|
* PHY0 connects to GE0.
|
|
*/
|
|
if ((resource_int_value("ar933x_gmac", 0, "override_phy", &val) == 0)
|
|
&& (val == 0))
|
|
return;
|
|
if ((resource_int_value("ar933x_gmac", 0, "swap_phy", &val) == 0)
|
|
&& (val == 1))
|
|
gmac_cfg |= AR933X_ETH_CFG_SW_PHY_SWAP;
|
|
if ((resource_int_value("ar933x_gmac", 0, "swap_phy_addr", &val) == 0)
|
|
&& (val == 1))
|
|
gmac_cfg |= AR933X_ETH_CFG_SW_PHY_ADDR_SWAP;
|
|
ar933x_configure_gmac(gmac_cfg);
|
|
}
|
|
|
|
struct ar71xx_cpu_def ar933x_chip_def = {
|
|
&ar933x_chip_detect_mem_size,
|
|
&ar933x_chip_detect_sys_frequency,
|
|
&ar933x_chip_device_stop,
|
|
&ar933x_chip_device_start,
|
|
&ar933x_chip_device_stopped,
|
|
&ar933x_chip_set_pll_ge,
|
|
&ar933x_chip_set_mii_speed,
|
|
&ar71xx_chip_set_mii_if,
|
|
&ar933x_chip_get_eth_pll,
|
|
&ar933x_chip_ddr_flush,
|
|
&ar933x_chip_init_usb_peripheral,
|
|
NULL,
|
|
NULL,
|
|
&ar933x_chip_init_gmac,
|
|
};
|