freebsd-dev/sys/i386/isa/ctx.c
Poul-Henning Kamp 7ac40f5f59 Gigacommit to improve device-driver source compatibility between
branches:

Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.

This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.

Approved by:    re(scottl)
2003-03-03 12:15:54 +00:00

452 lines
13 KiB
C

/*
* CORTEX-I Frame Grabber driver V1.0
*
* Copyright (C) 1994, Paul S. LaFollette, Jr. This software may be used,
* modified, copied, distributed, and sold, in both source and binary form
* provided that the above copyright and these terms are retained. Under
* no circumstances is the author responsible for the proper functioning
* of this software, nor does the author assume any responsibility
* for damages incurred with its use.
*
* $FreeBSD$
*/
/*
*
*
*
* Device Driver for CORTEX-I Frame Grabber
* Made by ImageNation Corporation
* 1200 N.E. Keyues Road
* Vancouver, WA 98684 (206) 944-9131
* (I have no ties to this company, just thought you might want
* to know how to get in touch with them.)
*
* In order to understand this device, you really need to consult the
* manual which ImageNation provides when you buy the board. (And
* what a pleasure it is to buy something for a PC and actually get
* programming information along with it.) I will limit myself here to
* a few comments which are specific to this driver. See also the file
* ctxreg.h for definitions of registers and control bits.
*
* 1. Although the hardware supports low resolution (256 x 256)
* acqusition and display, I have not implemented access to
* these modes in this driver. There are some fairly quirky
* aspects to the way this board works in low resolution mode,
* and I don't want to deal with them. Maybe later.
*
* 2. Choosing the base address for the video memory: This is set
* using a combination of hardware and software, using the left
* most dip switch on the board, and the AB_SELECT bit of control
* port 1, according to the chart below:
*
* Left DIP switch || DOWN | UP |
* =================================================
* AB_SELECT = 0 || 0xA0000 | 0xB0000 |
* -------------------------------------------------
* AB_SELECT = 1 || 0xD0000 | 0xE0000 |
* ------------------------------------------------
*
* When the RAM_ENABLE bit of control port 1 is clear (0), the
* video ram is disconnected from the computer bus. This makes
* it possible, in principle, to share memory space with other
* devices (such as VGA) which can also disconnect themselves
* from the bus. It also means that multiple CORTEX-I boards
* can share the same video memory space. Disconnecting from the
* bus does not affect the video display of the video ram contents,
* so that one needs only set the RAM_ENABLE bit when actually
* reading or writing to memory. The cost of this is low,
* the benefits to me are great (I need more than one board
* in my machine, and 0xE0000 is the only address choice that
* doesn't conflict with anything) so I adopt this strategy here.
*
* XXX-Note... this driver has only been tested for the
* XXX base = 0xE0000 case!
*
* 3) There is a deficiency in the documentation from ImageNation, I
* think. In order to successfully load the lookup table, it is
* necessary to clear SEE_STORED_VIDEO in control port 0 as well as
* setting LUT_LOAD_ENABLE in control port 1.
*
* 4) This driver accesses video memory through read or write operations.
* Other functionality is provided through ioctl's, manifest
* constants for which are defined in ioctl_ctx.h. The ioctl's
* include:
* CTX_LIVE Display live video
* CTX_GRAB Grab a frame of video data
* CTX_H_ORGANIZE Set things up so that sequential read
* operations access horizontal lines of
* pixels.
* CTX_V_ORGANIZE Set things up so that sequential read
* operations access vertical lines of
* pixels.
* CTX_SET_LUT Set the lookup table from an array
* of 256 unsigned chars passed as the
* third parameter to ioctl.
* CTX_GET_LUT Return the current lookup table to
* the application as an array of 256
* unsigned chars. Again the third
* parameter to the ioctl call.
*
* Thus,
* ioctl(fi, CTX_H_ORGANIZE, 0);
* lseek(fi, y*512, SEEK_SET);
* read(fi, buffer, 512);
*
* will fill buffer with 512 pixels (unsigned chars) which represent
* the y-th horizontal line of the image.
* Similarly,
* ioctl(fi, CTX_V_ORGANIZE, 0:
* lseek(fi, x*512+y, SEEK_SET);
* read(fi, buffer, 10);
*
* will read 10 a vertical line of 10 pixels starting at (x,y).
*
* Obviously, this sort of ugliness needs to be hidden away from
* the casual user, with an appropriate set of higher level
* functions.
*
*/
#include "ctx.h"
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/conf.h>
#include <sys/uio.h>
#include <sys/malloc.h>
#include <sys/bus.h>
#include <i386/isa/isa_device.h>
#include <i386/isa/ctxreg.h>
#include <machine/ioctl_ctx.h>
#include <machine/md_var.h>
#ifndef COMPAT_OLDISA
#error "The ctx device requires the old isa compatibility shims"
#endif
static int waitvb(int port);
/* state flags */
#define OPEN (0x01) /* device is open */
#define UNIT(x) ((x) & 0x07)
static int ctxprobe(struct isa_device *devp);
static int ctxattach(struct isa_device *devp);
struct isa_driver ctxdriver = {
INTR_TYPE_MISC,
ctxprobe,
ctxattach,
"ctx"
};
COMPAT_ISA_DRIVER(ctx, ctxdriver);
static d_open_t ctxopen;
static d_close_t ctxclose;
static d_read_t ctxread;
static d_write_t ctxwrite;
static d_ioctl_t ctxioctl;
#define CDEV_MAJOR 40
static struct cdevsw ctx_cdevsw = {
.d_open = ctxopen,
.d_close = ctxclose,
.d_read = ctxread,
.d_write = ctxwrite,
.d_ioctl = ctxioctl,
.d_name = "ctx",
.d_maj = CDEV_MAJOR,
};
#define LUTSIZE 256 /* buffer size for Look Up Table (LUT) */
#define PAGESIZE 65536 /* size of one video page, 1/4 of the screen */
/*
* Per unit shadow registers (because the dumb hardware is RO)
*/
static struct ctx_soft_registers {
u_char *lutp;
u_char cp0;
u_char cp1;
u_char flag;
int iobase;
caddr_t maddr;
int msize;
} ctx_sr[NCTX];
static int
ctxprobe(struct isa_device * devp)
{
int status;
if (inb(devp->id_iobase) == 0xff) /* 0xff only if board absent */
status = 0;
else {
status = 1; /*XXX uses only one port? */
}
return (status);
}
static int
ctxattach(struct isa_device * devp)
{
struct ctx_soft_registers *sr;
sr = &(ctx_sr[devp->id_unit]);
sr->cp0 = 0; /* zero out the shadow registers */
sr->cp1 = 0; /* and the open flag. wait for */
sr->flag = 0; /* open to malloc the LUT space */
sr->iobase = devp->id_iobase;
sr->maddr = devp->id_maddr;
sr->msize = devp->id_msize;
make_dev(&ctx_cdevsw, 0, 0, 0, 0600, "ctx%d", devp->id_unit);
return (1);
}
static int
ctxopen(dev_t dev, int flags, int fmt, struct thread *td)
{
struct ctx_soft_registers *sr;
u_char unit;
int i;
unit = UNIT(minor(dev));
/* minor number out of range? */
if (unit >= NCTX)
return (ENXIO);
sr = &(ctx_sr[unit]);
if (sr->flag != 0) /* someone has already opened us */
return (EBUSY);
/* get space for the LUT buffer */
sr->lutp = malloc(LUTSIZE, M_DEVBUF, M_WAITOK);
if (sr->lutp == NULL)
return (ENOMEM);
sr->flag = OPEN;
/*
Set up the shadow registers. We don't actually write these
values to the control ports until after we finish loading the
lookup table.
*/
sr->cp0 |= SEE_STORED_VIDEO;
if ((kvtop(sr->maddr) == 0xB0000) || (kvtop(sr->maddr) == 0xE0000))
sr->cp1 |= AB_SELECT; /* map to B or E if necessary */
/* but don't enable RAM */
/*
Set up the lookup table initially so that it is transparent.
*/
outb(sr->iobase + ctx_cp0, (u_char) 0);
outb(sr->iobase + ctx_cp1, (u_char) (LUT_LOAD_ENABLE | BLANK_DISPLAY));
for (i = 0; i < LUTSIZE; i++) {
outb(sr->iobase + ctx_lutaddr, (u_char) i);
sr->lutp[i] = (u_char) i;
outb(sr->iobase + ctx_lutdata, (u_char) sr->lutp[i]);
}
/*
Disable LUT loading, and push the data in the shadow
registers into the control ports.
*/
outb(sr->iobase + ctx_cp0, sr->cp0);
outb(sr->iobase + ctx_cp1, sr->cp1);
return (0); /* successful open. All ready to go. */
}
static int
ctxclose(dev_t dev, int flags, int fmt, struct thread *td)
{
int unit;
unit = UNIT(minor(dev));
ctx_sr[unit].flag = 0;
free(ctx_sr[unit].lutp, M_DEVBUF);
ctx_sr[unit].lutp = NULL;
return (0);
}
static int
ctxwrite(dev_t dev, struct uio * uio, int ioflag)
{
int unit, status = 0;
int page, count, offset;
struct ctx_soft_registers *sr;
unit = UNIT(minor(dev));
sr = &(ctx_sr[unit]);
if (uio->uio_offset < 0)
return (EINVAL);
if (uio->uio_offset >= 4 * PAGESIZE)
page = 4; /* EOF */
else
page = (u_int)uio->uio_offset / PAGESIZE;
offset = (u_int)uio->uio_offset % PAGESIZE;
count = min(uio->uio_resid, PAGESIZE - offset);
while ((page >= 0) && (page <= 3) && (count > 0)) {
sr->cp0 &= ~3;
sr->cp0 |= page;
outb(sr->iobase + ctx_cp0, sr->cp0);
/*
Before doing the uiomove, we need to "connect" the frame buffer
ram to the machine bus. This is done here so that we can have
several different boards installed, all sharing the same memory
space... each board is only "connected" to the bus when its memory
is actually being read or written. All my instincts tell me that
I should disable interrupts here, so I have done so.
*/
disable_intr();
sr->cp1 |= RAM_ENABLE;
outb(sr->iobase + ctx_cp1, sr->cp1);
status = uiomove(sr->maddr + offset, count, uio);
sr->cp1 &= ~RAM_ENABLE;
outb(sr->iobase + ctx_cp1, sr->cp1);
enable_intr();
page = (u_int)uio->uio_offset / PAGESIZE;
offset = (u_int)uio->uio_offset % PAGESIZE;
count = min(uio->uio_resid, PAGESIZE - offset);
}
if (uio->uio_resid > 0)
return (ENOSPC);
else
return (status);
}
static int
ctxread(dev_t dev, struct uio * uio, int ioflag)
{
int unit, status = 0;
int page, count, offset;
struct ctx_soft_registers *sr;
unit = UNIT(minor(dev));
sr = &(ctx_sr[unit]);
if (uio->uio_offset < 0)
return (EINVAL);
if (uio->uio_offset >= 4 * PAGESIZE)
page = 4; /* EOF */
else
page = (u_int)uio->uio_offset / PAGESIZE;
offset = (u_int)uio->uio_offset % PAGESIZE;
count = min(uio->uio_resid, PAGESIZE - offset);
while ((page >= 0) && (page <= 3) && (count > 0)) {
sr->cp0 &= ~3;
sr->cp0 |= page;
outb(sr->iobase + ctx_cp0, sr->cp0);
/*
Before doing the uiomove, we need to "connect" the frame buffer
ram to the machine bus. This is done here so that we can have
several different boards installed, all sharing the same memory
space... each board is only "connected" to the bus when its memory
is actually being read or written. All my instincts tell me that
I should disable interrupts here, so I have done so.
*/
disable_intr();
sr->cp1 |= RAM_ENABLE;
outb(sr->iobase + ctx_cp1, sr->cp1);
status = uiomove(sr->maddr + offset, count, uio);
sr->cp1 &= ~RAM_ENABLE;
outb(sr->iobase + ctx_cp1, sr->cp1);
enable_intr();
page = (u_int)uio->uio_offset / PAGESIZE;
offset = (u_int)uio->uio_offset % PAGESIZE;
count = min(uio->uio_resid, PAGESIZE - offset);
}
if (uio->uio_resid > 0)
return (ENOSPC);
else
return (status);
}
static int
ctxioctl(dev_t dev, u_long cmd, caddr_t data, int flags, struct thread *td)
{
int error;
int unit, i;
struct ctx_soft_registers *sr;
error = 0;
unit = UNIT(minor(dev));
sr = &(ctx_sr[unit]);
switch (cmd) {
case CTX_LIVE:
sr->cp0 &= ~SEE_STORED_VIDEO;
outb(sr->iobase + ctx_cp0, sr->cp0);
break;
case CTX_GRAB:
sr->cp0 &= ~SEE_STORED_VIDEO;
outb(sr->iobase + ctx_cp0, sr->cp0);
sr->cp0 |= ACQUIRE;
if (waitvb(sr->iobase)) /* wait for vert blank to start
* acquire */
error = ENODEV;
outb(sr->iobase + ctx_cp0, sr->cp0);
if (waitvb(sr->iobase)) /* wait for two more to finish acquire */
error = ENODEV;
if (waitvb(sr->iobase))
error = ENODEV;
sr->cp0 &= ~ACQUIRE; /* turn off acquire and turn on
* display */
sr->cp0 |= SEE_STORED_VIDEO;
outb(sr->iobase + ctx_cp0, sr->cp0);
break;
case CTX_H_ORGANIZE:
sr->cp0 &= ~PAGE_ROTATE;
outb(sr->iobase + ctx_cp0, sr->cp0);
break;
case CTX_V_ORGANIZE:
sr->cp0 |= PAGE_ROTATE;
outb(sr->iobase + ctx_cp0, sr->cp0);
break;
case CTX_SET_LUT:
bcopy((u_char *) data, sr->lutp, LUTSIZE);
outb(sr->iobase + ctx_cp0, (u_char) 0);
outb(sr->iobase + ctx_cp1, (u_char) (LUT_LOAD_ENABLE | BLANK_DISPLAY));
for (i = 0; i < LUTSIZE; i++) {
outb(sr->iobase + ctx_lutaddr, i);
outb(sr->iobase + ctx_lutdata, sr->lutp[i]);
}
outb(sr->iobase + ctx_cp0, sr->cp0); /* restore control
* registers */
outb(sr->iobase + ctx_cp1, sr->cp1);
break;
case CTX_GET_LUT:
bcopy(sr->lutp, (u_char *) data, LUTSIZE);
break;
default:
error = ENODEV;
}
return (error);
}
static int
waitvb(int port)
{ /* wait for a vertical blank, */
if (inb(port) == 0xff) /* 0xff means no board present */
return (1);
while ((inb(port) & VERTICAL_BLANK) != 0) {
}
while ((inb(port) & VERTICAL_BLANK) == 0) {
}
return (0);
}