d/freebsd-dev
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
a3924cd9b4
freebsd-dev/sys/dev/aic7xxx/aic79xx_inline.h
Justin T. Gibbs 4164174aff aic79xx.c: 
aic79xx.seq:
	Convert the COMPLETE_DMA_SCB list to an "stailq".  This allows us to
	safely keep the SCB that is currently being DMA'ed back the host on
	the head of the list while processing completions off of the bus.  The
	newly completed SCBs are appended to the tail of the queue.   In the
	past, we just dequeued the SCB that was in flight from the list, but
	this could result in a lost completion should the host perform certain
	types of error recovery that must cancel all in-flight SCB DMA operations.

	Switch from using a 16bit completion entry, holding just the tag and the
	completion valid bit, to a 64bit completion entry that also contains a
	"status packet valid" indicator.  This solves two problems:
	  o The SCB DMA engine on at least Rev B. silicon does not properly deal
	    with a PCI disconnect that occurs at a non-64bit aligned offset in the
	    chips "source buffer".  When the transfer is resumed, the DMA engine
	    continues at the correct offset, but may wrap to the head of the buffer
	    causing duplicate completions to be reported to the host.  By using a
	    completion buffer in host memory that is 64bit aligned and using 64bit
	    completion entries, such disconnects should only occur at aligned addresses.
	    This assumes that the host bridge will only disconnect on cache-line
	    boundaries and that cache-lines are multpiles of 64bits.

	  o By embedding the status information in the completion entry we can avoid
	    an extra memory reference to the HSCB for commands that complete without
	    error.

	Use the comparison of a "host freeze count" and a "sequencer freeze count"
	to allow the host to process most SCBs that complete with non-zero status
	without having to clear critical sections.  Instead the host can just pause the
	sequencer, performs any necessary cleanup in the waiting for selection list,
	increments its freeze count on the controller, and unpauses.  This is only
	possible because the sequencer defers completions of SCBs with bad status
	until after all pending selections have completed.  The sequencer then avoids
	referencing any data structures the host may touch during completion of the
	SCB until the freeze counts match.

aic79xx.c:
	Change the strategy for allocating our sentinal HSCB for the QINFIFO.  In
	the past, this allocation was tacked onto the QOUTFIFO allocation.  Now that
	the qoutfifo has grown to accomodate larger completion entries, the old
	approach will result in a 64byte allocation that costs an extra page of
	coherent memory.  We now do this extra allocation via ahd_alloc_scbs()
	where the "unused space" can be used to allocate "normal" HSCBs.

	In our packetized busfree handler, use the ENSELO bit to differentiate
	between packetized and non-packetized unexpected busfree events that
	occur just after selection, but before the sequencer has had the oportunity
	to service the selection.

	When cleaning out the waiting for selection list, use the SCSI mode
	instead of the command channel mode.  The SCB pointer in the command
	channel mode may be referenced by the SCB dma engine even while the
	sequencer is paused, whereas the SCSI mode SCB pointer is only accessed
	by the sequencer.

	Print the "complete on qfreeze" sequencer SCB completion list in
	ahd_dump_card_state().  This list holds all SCB completions that are deferred
	until a pending select-out qfreeze event has taken effect.

aic79xx.h:
	Add definitions and structures to handle the new SCB completion scheme.

	Add a controller flag that indicates if the controller is in HostRAID
	mode.

aic79xx.reg:
	Remove macros used for toggling from one data fifo mode to the other.
	They have not been in use for some time.

	Add scratch ram fields for our new qfreeze count scheme, converting
	the complete dma list into an "stailq", and providing for the "complete
	on qfreeze" SCB completion list.  Some other fields were moved to retain
	proper field alignment (alignment >= field size in bytes).

aic79xx.seq:
	Add code to our idle loop to:
	  o Process deferred completions once a qfreeze event has taken full
	    effect.
	  o Thaw the queue once the sequencer and host qfreeze counts match.

	Generate 64bit completion entries passing the SCB_SGPTR field as the
	"good status" indicator.  The first bit in this field is only set if
	we have a valid status packet to send to the host.

	Convert the COMPLETE_DMA_SCB list to an "stailq".

	When using "setjmp" to register an idle loop handler, do not combine
	the "ret" with the block move to pop the stack address in the same
	instruction.  At least on the A, this results in a return to the setjmp
	caller, not to the new address at the top of the stack.  Since we want
	the latter (we want the newly registered handler to only be invoked from
	the idle loop), we must use a separate ret instruction.

	Add a few missing critical sections.

	Close a race condition that can occur on Rev A. silicon.  If both FIFOs
	happen to be allocated before the sequencer has a chance to service the
	FIFO that was allocated first, we must take special care to service the
	FIFO that is not active on the SCSI bus first.  This guarantees that a
	FIFO will be freed to handle any snapshot requests for the FIFO that is
	still on the bus.  Chosing the incorrect FIFO will result in deadlock.

	Update comments.

aic79xx_inline.h
	Correct the offset calculation for the syncing of our qoutfifo.

	Update ahd_check_cmdcmpltqueues() for the larger completion entries.

aic79xx_pci.c:
	Attach to HostRAID controllers by default.  In the future I may add a
	sysctl to modify the behavior, but since FreeBSD does not have any
	HostRAID drivers, failing to attach just results in more email and
	bug reports for the author.

MFC After: 1week
2004-02-04 16:38:38 +00:00

980 lines
29 KiB
C
Raw Blame History

/*
* Inline routines shareable across OS platforms.
*
* Copyright (c) 1994-2001 Justin T. Gibbs.
* Copyright (c) 2000-2003 Adaptec Inc.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*
* $Id: //depot/aic7xxx/aic7xxx/aic79xx_inline.h#56 $
*
* $FreeBSD$
*/
#ifndef _AIC79XX_INLINE_H_
#define _AIC79XX_INLINE_H_
/******************************** Debugging ***********************************/
static __inline char *ahd_name(struct ahd_softc *ahd);
static __inline char *
ahd_name(struct ahd_softc *ahd)
{
return (ahd->name);
}
/************************ Sequencer Execution Control *************************/
static __inline void ahd_known_modes(struct ahd_softc *ahd,
ahd_mode src, ahd_mode dst);
static __inline ahd_mode_state ahd_build_mode_state(struct ahd_softc *ahd,
ahd_mode src,
ahd_mode dst);
static __inline void ahd_extract_mode_state(struct ahd_softc *ahd,
ahd_mode_state state,
ahd_mode *src, ahd_mode *dst);
static __inline void ahd_set_modes(struct ahd_softc *ahd, ahd_mode src,
ahd_mode dst);
static __inline void ahd_update_modes(struct ahd_softc *ahd);
static __inline void ahd_assert_modes(struct ahd_softc *ahd, ahd_mode srcmode,
ahd_mode dstmode, const char *file,
int line);
static __inline ahd_mode_state ahd_save_modes(struct ahd_softc *ahd);
static __inline void ahd_restore_modes(struct ahd_softc *ahd,
ahd_mode_state state);
static __inline int ahd_is_paused(struct ahd_softc *ahd);
static __inline void ahd_pause(struct ahd_softc *ahd);
static __inline void ahd_unpause(struct ahd_softc *ahd);
static __inline void
ahd_known_modes(struct ahd_softc *ahd, ahd_mode src, ahd_mode dst)
{
ahd->src_mode = src;
ahd->dst_mode = dst;
ahd->saved_src_mode = src;
ahd->saved_dst_mode = dst;
}
static __inline ahd_mode_state
ahd_build_mode_state(struct ahd_softc *ahd, ahd_mode src, ahd_mode dst)
{
return ((src << SRC_MODE_SHIFT) | (dst << DST_MODE_SHIFT));
}
static __inline void
ahd_extract_mode_state(struct ahd_softc *ahd, ahd_mode_state state,
ahd_mode *src, ahd_mode *dst)
{
*src = (state & SRC_MODE) >> SRC_MODE_SHIFT;
*dst = (state & DST_MODE) >> DST_MODE_SHIFT;
}
static __inline void
ahd_set_modes(struct ahd_softc *ahd, ahd_mode src, ahd_mode dst)
{
if (ahd->src_mode == src && ahd->dst_mode == dst)
return;
#ifdef AHD_DEBUG
if (ahd->src_mode == AHD_MODE_UNKNOWN
|| ahd->dst_mode == AHD_MODE_UNKNOWN)
panic("Setting mode prior to saving it.\n");
if ((ahd_debug & AHD_SHOW_MODEPTR) != 0)
printf("%s: Setting mode 0x%x\n", ahd_name(ahd),
ahd_build_mode_state(ahd, src, dst));
#endif
ahd_outb(ahd, MODE_PTR, ahd_build_mode_state(ahd, src, dst));
ahd->src_mode = src;
ahd->dst_mode = dst;
}
static __inline void
ahd_update_modes(struct ahd_softc *ahd)
{
ahd_mode_state mode_ptr;
ahd_mode src;
ahd_mode dst;
mode_ptr = ahd_inb(ahd, MODE_PTR);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_MODEPTR) != 0)
printf("Reading mode 0x%x\n", mode_ptr);
#endif
ahd_extract_mode_state(ahd, mode_ptr, &src, &dst);
ahd_known_modes(ahd, src, dst);
}
static __inline void
ahd_assert_modes(struct ahd_softc *ahd, ahd_mode srcmode,
ahd_mode dstmode, const char *file, int line)
{
#ifdef AHD_DEBUG
if ((srcmode & AHD_MK_MSK(ahd->src_mode)) == 0
|| (dstmode & AHD_MK_MSK(ahd->dst_mode)) == 0) {
panic("%s:%s:%d: Mode assertion failed.\n",
ahd_name(ahd), file, line);
}
#endif
}
static __inline ahd_mode_state
ahd_save_modes(struct ahd_softc *ahd)
{
if (ahd->src_mode == AHD_MODE_UNKNOWN
|| ahd->dst_mode == AHD_MODE_UNKNOWN)
ahd_update_modes(ahd);
return (ahd_build_mode_state(ahd, ahd->src_mode, ahd->dst_mode));
}
static __inline void
ahd_restore_modes(struct ahd_softc *ahd, ahd_mode_state state)
{
ahd_mode src;
ahd_mode dst;
ahd_extract_mode_state(ahd, state, &src, &dst);
ahd_set_modes(ahd, src, dst);
}
#define AHD_ASSERT_MODES(ahd, source, dest) \
ahd_assert_modes(ahd, source, dest, __FILE__, __LINE__);
/*
* Determine whether the sequencer has halted code execution.
* Returns non-zero status if the sequencer is stopped.
*/
static __inline int
ahd_is_paused(struct ahd_softc *ahd)
{
return ((ahd_inb(ahd, HCNTRL) & PAUSE) != 0);
}
/*
* Request that the sequencer stop and wait, indefinitely, for it
* to stop. The sequencer will only acknowledge that it is paused
* once it has reached an instruction boundary and PAUSEDIS is
* cleared in the SEQCTL register. The sequencer may use PAUSEDIS
* for critical sections.
*/
static __inline void
ahd_pause(struct ahd_softc *ahd)
{
ahd_outb(ahd, HCNTRL, ahd->pause);
/*
* Since the sequencer can disable pausing in a critical section, we
* must loop until it actually stops.
*/
while (ahd_is_paused(ahd) == 0)
;
}
/*
* Allow the sequencer to continue program execution.
* We check here to ensure that no additional interrupt
* sources that would cause the sequencer to halt have been
* asserted. If, for example, a SCSI bus reset is detected
* while we are fielding a different, pausing, interrupt type,
* we don't want to release the sequencer before going back
* into our interrupt handler and dealing with this new
* condition.
*/
static __inline void
ahd_unpause(struct ahd_softc *ahd)
{
/*
* Automatically restore our modes to those saved
* prior to the first change of the mode.
*/
if (ahd->saved_src_mode != AHD_MODE_UNKNOWN
&& ahd->saved_dst_mode != AHD_MODE_UNKNOWN) {
if ((ahd->flags & AHD_UPDATE_PEND_CMDS) != 0)
ahd_reset_cmds_pending(ahd);
ahd_set_modes(ahd, ahd->saved_src_mode, ahd->saved_dst_mode);
}
if ((ahd_inb(ahd, INTSTAT) & ~CMDCMPLT) == 0)
ahd_outb(ahd, HCNTRL, ahd->unpause);
ahd_known_modes(ahd, AHD_MODE_UNKNOWN, AHD_MODE_UNKNOWN);
}
/*********************** Scatter Gather List Handling *************************/
static __inline void *ahd_sg_setup(struct ahd_softc *ahd, struct scb *scb,
void *sgptr, bus_addr_t addr,
bus_size_t len, int last);
static __inline void ahd_setup_scb_common(struct ahd_softc *ahd,
struct scb *scb);
static __inline void ahd_setup_data_scb(struct ahd_softc *ahd,
struct scb *scb);
static __inline void ahd_setup_noxfer_scb(struct ahd_softc *ahd,
struct scb *scb);
static __inline void *
ahd_sg_setup(struct ahd_softc *ahd, struct scb *scb,
void *sgptr, bus_addr_t addr, bus_size_t len, int last)
{
scb->sg_count++;
if (sizeof(bus_addr_t) > 4
&& (ahd->flags & AHD_64BIT_ADDRESSING) != 0) {
struct ahd_dma64_seg *sg;
sg = (struct ahd_dma64_seg *)sgptr;
sg->addr = aic_htole64(addr);
sg->len = aic_htole32(len | (last ? AHD_DMA_LAST_SEG : 0));
return (sg + 1);
} else {
struct ahd_dma_seg *sg;
sg = (struct ahd_dma_seg *)sgptr;
sg->addr = aic_htole32(addr & 0xFFFFFFFF);
sg->len = aic_htole32(len | ((addr >> 8) & 0x7F000000)
| (last ? AHD_DMA_LAST_SEG : 0));
return (sg + 1);
}
}
static __inline void
ahd_setup_scb_common(struct ahd_softc *ahd, struct scb *scb)
{
/* XXX Handle target mode SCBs. */
scb->crc_retry_count = 0;
if ((scb->flags & SCB_PACKETIZED) != 0) {
/* XXX what about ACA?? It is type 4, but TAG_TYPE == 0x3. */
scb->hscb->task_attribute = scb->hscb->control & SCB_TAG_TYPE;
} else {
if (aic_get_transfer_length(scb) & 0x01)
scb->hscb->task_attribute = SCB_XFERLEN_ODD;
else
scb->hscb->task_attribute = 0;
}
if (scb->hscb->cdb_len <= MAX_CDB_LEN_WITH_SENSE_ADDR
|| (scb->hscb->cdb_len & SCB_CDB_LEN_PTR) != 0)
scb->hscb->shared_data.idata.cdb_plus_saddr.sense_addr =
aic_htole32(scb->sense_busaddr);
}
static __inline void
ahd_setup_data_scb(struct ahd_softc *ahd, struct scb *scb)
{
/*
* Copy the first SG into the "current" data ponter area.
*/
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0) {
struct ahd_dma64_seg *sg;
sg = (struct ahd_dma64_seg *)scb->sg_list;
scb->hscb->dataptr = sg->addr;
scb->hscb->datacnt = sg->len;
} else {
struct ahd_dma_seg *sg;
uint32_t *dataptr_words;
sg = (struct ahd_dma_seg *)scb->sg_list;
dataptr_words = (uint32_t*)&scb->hscb->dataptr;
dataptr_words[0] = sg->addr;
dataptr_words[1] = 0;
if ((ahd->flags & AHD_39BIT_ADDRESSING) != 0) {
uint64_t high_addr;
high_addr = aic_le32toh(sg->len) & 0x7F000000;
scb->hscb->dataptr |= aic_htole64(high_addr << 8);
}
scb->hscb->datacnt = sg->len;
}
/*
* Note where to find the SG entries in bus space.
* We also set the full residual flag which the
* sequencer will clear as soon as a data transfer
* occurs.
*/
scb->hscb->sgptr = aic_htole32(scb->sg_list_busaddr|SG_FULL_RESID);
}
static __inline void
ahd_setup_noxfer_scb(struct ahd_softc *ahd, struct scb *scb)
{
scb->hscb->sgptr = aic_htole32(SG_LIST_NULL);
scb->hscb->dataptr = 0;
scb->hscb->datacnt = 0;
}
/************************** Memory mapping routines ***************************/
static __inline size_t ahd_sg_size(struct ahd_softc *ahd);
static __inline void *
ahd_sg_bus_to_virt(struct ahd_softc *ahd,
struct scb *scb,
uint32_t sg_busaddr);
static __inline uint32_t
ahd_sg_virt_to_bus(struct ahd_softc *ahd,
struct scb *scb,
void *sg);
static __inline void ahd_sync_scb(struct ahd_softc *ahd,
struct scb *scb, int op);
static __inline void ahd_sync_sglist(struct ahd_softc *ahd,
struct scb *scb, int op);
static __inline void ahd_sync_sense(struct ahd_softc *ahd,
struct scb *scb, int op);
static __inline uint32_t
ahd_targetcmd_offset(struct ahd_softc *ahd,
u_int index);
static __inline size_t
ahd_sg_size(struct ahd_softc *ahd)
{
if ((ahd->flags & AHD_64BIT_ADDRESSING) != 0)
return (sizeof(struct ahd_dma64_seg));
return (sizeof(struct ahd_dma_seg));
}
static __inline void *
ahd_sg_bus_to_virt(struct ahd_softc *ahd, struct scb *scb, uint32_t sg_busaddr)
{
bus_addr_t sg_offset;
/* sg_list_phys points to entry 1, not 0 */
sg_offset = sg_busaddr - (scb->sg_list_busaddr - ahd_sg_size(ahd));
return ((uint8_t *)scb->sg_list + sg_offset);
}
static __inline uint32_t
ahd_sg_virt_to_bus(struct ahd_softc *ahd, struct scb *scb, void *sg)
{
bus_addr_t sg_offset;
/* sg_list_phys points to entry 1, not 0 */
sg_offset = ((uint8_t *)sg - (uint8_t *)scb->sg_list)
- ahd_sg_size(ahd);
return (scb->sg_list_busaddr + sg_offset);
}
static __inline void
ahd_sync_scb(struct ahd_softc *ahd, struct scb *scb, int op)
{
aic_dmamap_sync(ahd, ahd->scb_data.hscb_dmat,
scb->hscb_map->dmamap,
/*offset*/(uint8_t*)scb->hscb - scb->hscb_map->vaddr,
/*len*/sizeof(*scb->hscb), op);
}
static __inline void
ahd_sync_sglist(struct ahd_softc *ahd, struct scb *scb, int op)
{
if (scb->sg_count == 0)
return;
aic_dmamap_sync(ahd, ahd->scb_data.sg_dmat,
scb->sg_map->dmamap,
/*offset*/scb->sg_list_busaddr - ahd_sg_size(ahd),
/*len*/ahd_sg_size(ahd) * scb->sg_count, op);
}
static __inline void
ahd_sync_sense(struct ahd_softc *ahd, struct scb *scb, int op)
{
aic_dmamap_sync(ahd, ahd->scb_data.sense_dmat,
scb->sense_map->dmamap,
/*offset*/scb->sense_busaddr,
/*len*/AHD_SENSE_BUFSIZE, op);
}
static __inline uint32_t
ahd_targetcmd_offset(struct ahd_softc *ahd, u_int index)
{
return (((uint8_t *)&ahd->targetcmds[index])
- (uint8_t *)ahd->qoutfifo);
}
/*********************** Miscelaneous Support Functions ***********************/
static __inline void ahd_complete_scb(struct ahd_softc *ahd,
struct scb *scb);
static __inline void ahd_update_residual(struct ahd_softc *ahd,
struct scb *scb);
static __inline struct ahd_initiator_tinfo *
ahd_fetch_transinfo(struct ahd_softc *ahd,
char channel, u_int our_id,
u_int remote_id,
struct ahd_tmode_tstate **tstate);
static __inline uint16_t
ahd_inw(struct ahd_softc *ahd, u_int port);
static __inline void ahd_outw(struct ahd_softc *ahd, u_int port,
u_int value);
static __inline uint32_t
ahd_inl(struct ahd_softc *ahd, u_int port);
static __inline void ahd_outl(struct ahd_softc *ahd, u_int port,
uint32_t value);
static __inline uint64_t
ahd_inq(struct ahd_softc *ahd, u_int port);
static __inline void ahd_outq(struct ahd_softc *ahd, u_int port,
uint64_t value);
static __inline u_int ahd_get_scbptr(struct ahd_softc *ahd);
static __inline void ahd_set_scbptr(struct ahd_softc *ahd, u_int scbptr);
static __inline u_int ahd_get_hnscb_qoff(struct ahd_softc *ahd);
static __inline void ahd_set_hnscb_qoff(struct ahd_softc *ahd, u_int value);
static __inline u_int ahd_get_hescb_qoff(struct ahd_softc *ahd);
static __inline void ahd_set_hescb_qoff(struct ahd_softc *ahd, u_int value);
static __inline u_int ahd_get_snscb_qoff(struct ahd_softc *ahd);
static __inline void ahd_set_snscb_qoff(struct ahd_softc *ahd, u_int value);
static __inline u_int ahd_get_sescb_qoff(struct ahd_softc *ahd);
static __inline void ahd_set_sescb_qoff(struct ahd_softc *ahd, u_int value);
static __inline u_int ahd_get_sdscb_qoff(struct ahd_softc *ahd);
static __inline void ahd_set_sdscb_qoff(struct ahd_softc *ahd, u_int value);
static __inline u_int ahd_inb_scbram(struct ahd_softc *ahd, u_int offset);
static __inline u_int ahd_inw_scbram(struct ahd_softc *ahd, u_int offset);
static __inline uint32_t
ahd_inl_scbram(struct ahd_softc *ahd, u_int offset);
static __inline uint64_t
ahd_inq_scbram(struct ahd_softc *ahd, u_int offset);
static __inline void ahd_swap_with_next_hscb(struct ahd_softc *ahd,
struct scb *scb);
static __inline void ahd_queue_scb(struct ahd_softc *ahd, struct scb *scb);
static __inline uint8_t *
ahd_get_sense_buf(struct ahd_softc *ahd,
struct scb *scb);
static __inline uint32_t
ahd_get_sense_bufaddr(struct ahd_softc *ahd,
struct scb *scb);
static __inline void
ahd_complete_scb(struct ahd_softc *ahd, struct scb *scb)
{
uint32_t sgptr;
sgptr = aic_le32toh(scb->hscb->sgptr);
if ((sgptr & SG_STATUS_VALID) != 0)
ahd_handle_scb_status(ahd, scb);
else
ahd_done(ahd, scb);
}
/*
* Determine whether the sequencer reported a residual
* for this SCB/transaction.
*/
static __inline void
ahd_update_residual(struct ahd_softc *ahd, struct scb *scb)
{
uint32_t sgptr;
sgptr = aic_le32toh(scb->hscb->sgptr);
if ((sgptr & SG_STATUS_VALID) != 0)
ahd_calc_residual(ahd, scb);
}
/*
* Return pointers to the transfer negotiation information
* for the specified our_id/remote_id pair.
*/
static __inline struct ahd_initiator_tinfo *
ahd_fetch_transinfo(struct ahd_softc *ahd, char channel, u_int our_id,
u_int remote_id, struct ahd_tmode_tstate **tstate)
{
/*
* Transfer data structures are stored from the perspective
* of the target role. Since the parameters for a connection
* in the initiator role to a given target are the same as
* when the roles are reversed, we pretend we are the target.
*/
if (channel == 'B')
our_id += 8;
*tstate = ahd->enabled_targets[our_id];
return (&(*tstate)->transinfo[remote_id]);
}
#define AHD_COPY_COL_IDX(dst, src) \
do { \
dst->hscb->scsiid = src->hscb->scsiid; \
dst->hscb->lun = src->hscb->lun; \
} while (0)
static __inline uint16_t
ahd_inw(struct ahd_softc *ahd, u_int port)
{
/*
* Read high byte first as some registers increment
* or have other side effects when the low byte is
* read.
*/
return ((ahd_inb(ahd, port+1) << 8) | ahd_inb(ahd, port));
}
static __inline void
ahd_outw(struct ahd_softc *ahd, u_int port, u_int value)
{
/*
* Write low byte first to accomodate registers
* such as PRGMCNT where the order maters.
*/
ahd_outb(ahd, port, value & 0xFF);
ahd_outb(ahd, port+1, (value >> 8) & 0xFF);
}
static __inline uint32_t
ahd_inl(struct ahd_softc *ahd, u_int port)
{
return ((ahd_inb(ahd, port))
| (ahd_inb(ahd, port+1) << 8)
| (ahd_inb(ahd, port+2) << 16)
| (ahd_inb(ahd, port+3) << 24));
}
static __inline void
ahd_outl(struct ahd_softc *ahd, u_int port, uint32_t value)
{
ahd_outb(ahd, port, (value) & 0xFF);
ahd_outb(ahd, port+1, ((value) >> 8) & 0xFF);
ahd_outb(ahd, port+2, ((value) >> 16) & 0xFF);
ahd_outb(ahd, port+3, ((value) >> 24) & 0xFF);
}
static __inline uint64_t
ahd_inq(struct ahd_softc *ahd, u_int port)
{
return ((ahd_inb(ahd, port))
| (ahd_inb(ahd, port+1) << 8)
| (ahd_inb(ahd, port+2) << 16)
| (ahd_inb(ahd, port+3) << 24)
| (((uint64_t)ahd_inb(ahd, port+4)) << 32)
| (((uint64_t)ahd_inb(ahd, port+5)) << 40)
| (((uint64_t)ahd_inb(ahd, port+6)) << 48)
| (((uint64_t)ahd_inb(ahd, port+7)) << 56));
}
static __inline void
ahd_outq(struct ahd_softc *ahd, u_int port, uint64_t value)
{
ahd_outb(ahd, port, value & 0xFF);
ahd_outb(ahd, port+1, (value >> 8) & 0xFF);
ahd_outb(ahd, port+2, (value >> 16) & 0xFF);
ahd_outb(ahd, port+3, (value >> 24) & 0xFF);
ahd_outb(ahd, port+4, (value >> 32) & 0xFF);
ahd_outb(ahd, port+5, (value >> 40) & 0xFF);
ahd_outb(ahd, port+6, (value >> 48) & 0xFF);
ahd_outb(ahd, port+7, (value >> 56) & 0xFF);
}
static __inline u_int
ahd_get_scbptr(struct ahd_softc *ahd)
{
AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK),
~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK));
return (ahd_inb(ahd, SCBPTR) | (ahd_inb(ahd, SCBPTR + 1) << 8));
}
static __inline void
ahd_set_scbptr(struct ahd_softc *ahd, u_int scbptr)
{
AHD_ASSERT_MODES(ahd, ~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK),
~(AHD_MODE_UNKNOWN_MSK|AHD_MODE_CFG_MSK));
ahd_outb(ahd, SCBPTR, scbptr & 0xFF);
ahd_outb(ahd, SCBPTR+1, (scbptr >> 8) & 0xFF);
}
static __inline u_int
ahd_get_hnscb_qoff(struct ahd_softc *ahd)
{
return (ahd_inw_atomic(ahd, HNSCB_QOFF));
}
static __inline void
ahd_set_hnscb_qoff(struct ahd_softc *ahd, u_int value)
{
ahd_outw_atomic(ahd, HNSCB_QOFF, value);
}
static __inline u_int
ahd_get_hescb_qoff(struct ahd_softc *ahd)
{
return (ahd_inb(ahd, HESCB_QOFF));
}
static __inline void
ahd_set_hescb_qoff(struct ahd_softc *ahd, u_int value)
{
ahd_outb(ahd, HESCB_QOFF, value);
}
static __inline u_int
ahd_get_snscb_qoff(struct ahd_softc *ahd)
{
u_int oldvalue;
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
oldvalue = ahd_inw(ahd, SNSCB_QOFF);
ahd_outw(ahd, SNSCB_QOFF, oldvalue);
return (oldvalue);
}
static __inline void
ahd_set_snscb_qoff(struct ahd_softc *ahd, u_int value)
{
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
ahd_outw(ahd, SNSCB_QOFF, value);
}
static __inline u_int
ahd_get_sescb_qoff(struct ahd_softc *ahd)
{
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
return (ahd_inb(ahd, SESCB_QOFF));
}
static __inline void
ahd_set_sescb_qoff(struct ahd_softc *ahd, u_int value)
{
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
ahd_outb(ahd, SESCB_QOFF, value);
}
static __inline u_int
ahd_get_sdscb_qoff(struct ahd_softc *ahd)
{
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
return (ahd_inb(ahd, SDSCB_QOFF) | (ahd_inb(ahd, SDSCB_QOFF + 1) << 8));
}
static __inline void
ahd_set_sdscb_qoff(struct ahd_softc *ahd, u_int value)
{
AHD_ASSERT_MODES(ahd, AHD_MODE_CCHAN_MSK, AHD_MODE_CCHAN_MSK);
ahd_outb(ahd, SDSCB_QOFF, value & 0xFF);
ahd_outb(ahd, SDSCB_QOFF+1, (value >> 8) & 0xFF);
}
static __inline u_int
ahd_inb_scbram(struct ahd_softc *ahd, u_int offset)
{
u_int value;
/*
* Workaround PCI-X Rev A. hardware bug.
* After a host read of SCB memory, the chip
* may become confused into thinking prefetch
* was required. This starts the discard timer
* running and can cause an unexpected discard
* timer interrupt. The work around is to read
* a normal register prior to the exhaustion of
* the discard timer. The mode pointer register
* has no side effects and so serves well for
* this purpose.
*
* Razor #528
*/
value = ahd_inb(ahd, offset);
if ((ahd->flags & AHD_PCIX_SCBRAM_RD_BUG) != 0)
ahd_inb(ahd, MODE_PTR);
return (value);
}
static __inline u_int
ahd_inw_scbram(struct ahd_softc *ahd, u_int offset)
{
return (ahd_inb_scbram(ahd, offset)
| (ahd_inb_scbram(ahd, offset+1) << 8));
}
static __inline uint32_t
ahd_inl_scbram(struct ahd_softc *ahd, u_int offset)
{
return (ahd_inw_scbram(ahd, offset)
| (ahd_inw_scbram(ahd, offset+2) << 16));
}
static __inline uint64_t
ahd_inq_scbram(struct ahd_softc *ahd, u_int offset)
{
return (ahd_inl_scbram(ahd, offset)
| ((uint64_t)ahd_inl_scbram(ahd, offset+4)) << 32);
}
static __inline struct scb *
ahd_lookup_scb(struct ahd_softc *ahd, u_int tag)
{
struct scb* scb;
if (tag >= AHD_SCB_MAX)
return (NULL);
scb = ahd->scb_data.scbindex[tag];
if (scb != NULL)
ahd_sync_scb(ahd, scb,
BUS_DMASYNC_POSTREAD|BUS_DMASYNC_POSTWRITE);
return (scb);
}
static __inline void
ahd_swap_with_next_hscb(struct ahd_softc *ahd, struct scb *scb)
{
struct hardware_scb *q_hscb;
struct map_node *q_hscb_map;
uint32_t saved_hscb_busaddr;
/*
* Our queuing method is a bit tricky. The card
* knows in advance which HSCB (by address) to download,
* and we can't disappoint it. To achieve this, the next
* HSCB to download is saved off in ahd->next_queued_hscb.
* When we are called to queue "an arbitrary scb",
* we copy the contents of the incoming HSCB to the one
* the sequencer knows about, swap HSCB pointers and
* finally assign the SCB to the tag indexed location
* in the scb_array. This makes sure that we can still
* locate the correct SCB by SCB_TAG.
*/
q_hscb = ahd->next_queued_hscb;
q_hscb_map = ahd->next_queued_hscb_map;
saved_hscb_busaddr = q_hscb->hscb_busaddr;
memcpy(q_hscb, scb->hscb, sizeof(*scb->hscb));
q_hscb->hscb_busaddr = saved_hscb_busaddr;
q_hscb->next_hscb_busaddr = scb->hscb->hscb_busaddr;
/* Now swap HSCB pointers. */
ahd->next_queued_hscb = scb->hscb;
ahd->next_queued_hscb_map = scb->hscb_map;
scb->hscb = q_hscb;
scb->hscb_map = q_hscb_map;
/* Now define the mapping from tag to SCB in the scbindex */
ahd->scb_data.scbindex[SCB_GET_TAG(scb)] = scb;
}
/*
* Tell the sequencer about a new transaction to execute.
*/
static __inline void
ahd_queue_scb(struct ahd_softc *ahd, struct scb *scb)
{
ahd_swap_with_next_hscb(ahd, scb);
if (SCBID_IS_NULL(SCB_GET_TAG(scb)))
panic("Attempt to queue invalid SCB tag %x\n",
SCB_GET_TAG(scb));
/*
* Keep a history of SCBs we've downloaded in the qinfifo.
*/
ahd->qinfifo[AHD_QIN_WRAP(ahd->qinfifonext)] = SCB_GET_TAG(scb);
ahd->qinfifonext++;
if (scb->sg_count != 0)
ahd_setup_data_scb(ahd, scb);
else
ahd_setup_noxfer_scb(ahd, scb);
ahd_setup_scb_common(ahd, scb);
/*
* Make sure our data is consistent from the
* perspective of the adapter.
*/
ahd_sync_scb(ahd, scb, BUS_DMASYNC_PREREAD|BUS_DMASYNC_PREWRITE);
#ifdef AHD_DEBUG
if ((ahd_debug & AHD_SHOW_QUEUE) != 0) {
uint64_t host_dataptr;
host_dataptr = aic_le64toh(scb->hscb->dataptr);
printf("%s: Queueing SCB 0x%x bus addr 0x%x - 0x%x%x/0x%x\n",
ahd_name(ahd),
SCB_GET_TAG(scb), aic_le32toh(scb->hscb->hscb_busaddr),
(u_int)((host_dataptr >> 32) & 0xFFFFFFFF),
(u_int)(host_dataptr & 0xFFFFFFFF),
aic_le32toh(scb->hscb->datacnt));
}
#endif
/* Tell the adapter about the newly queued SCB */
ahd_set_hnscb_qoff(ahd, ahd->qinfifonext);
}
static __inline uint8_t *
ahd_get_sense_buf(struct ahd_softc *ahd, struct scb *scb)
{
return (scb->sense_data);
}
static __inline uint32_t
ahd_get_sense_bufaddr(struct ahd_softc *ahd, struct scb *scb)
{
return (scb->sense_busaddr);
}
/************************** Interrupt Processing ******************************/
static __inline void ahd_sync_qoutfifo(struct ahd_softc *ahd, int op);
static __inline void ahd_sync_tqinfifo(struct ahd_softc *ahd, int op);
static __inline u_int ahd_check_cmdcmpltqueues(struct ahd_softc *ahd);
static __inline int ahd_intr(struct ahd_softc *ahd);
static __inline void
ahd_sync_qoutfifo(struct ahd_softc *ahd, int op)
{
aic_dmamap_sync(ahd, ahd->shared_data_dmat, ahd->shared_data_map.dmamap,
/*offset*/0,
/*len*/AHD_SCB_MAX * sizeof(struct ahd_completion), op);
}
static __inline void
ahd_sync_tqinfifo(struct ahd_softc *ahd, int op)
{
#ifdef AHD_TARGET_MODE
if ((ahd->flags & AHD_TARGETROLE) != 0) {
aic_dmamap_sync(ahd, ahd->shared_data_dmat,
ahd->shared_data_map.dmamap,
ahd_targetcmd_offset(ahd, 0),
sizeof(struct target_cmd) * AHD_TMODE_CMDS,
op);
}
#endif
}
/*
* See if the firmware has posted any completed commands
* into our in-core command complete fifos.
*/
#define AHD_RUN_QOUTFIFO 0x1
#define AHD_RUN_TQINFIFO 0x2
static __inline u_int
ahd_check_cmdcmpltqueues(struct ahd_softc *ahd)
{
u_int retval;
retval = 0;
aic_dmamap_sync(ahd, ahd->shared_data_dmat, ahd->shared_data_map.dmamap,
/*offset*/ahd->qoutfifonext * sizeof(*ahd->qoutfifo),
/*len*/sizeof(*ahd->qoutfifo), BUS_DMASYNC_POSTREAD);
if (ahd->qoutfifo[ahd->qoutfifonext].valid_tag
== ahd->qoutfifonext_valid_tag)
retval |= AHD_RUN_QOUTFIFO;
#ifdef AHD_TARGET_MODE
if ((ahd->flags & AHD_TARGETROLE) != 0
&& (ahd->flags & AHD_TQINFIFO_BLOCKED) == 0) {
aic_dmamap_sync(ahd, ahd->shared_data_dmat,
ahd->shared_data_map.dmamap,
ahd_targetcmd_offset(ahd, ahd->tqinfifofnext),
/*len*/sizeof(struct target_cmd),
BUS_DMASYNC_POSTREAD);
if (ahd->targetcmds[ahd->tqinfifonext].cmd_valid != 0)
retval |= AHD_RUN_TQINFIFO;
}
#endif
return (retval);
}
/*
* Catch an interrupt from the adapter
*/
static __inline int
ahd_intr(struct ahd_softc *ahd)
{
u_int intstat;
if ((ahd->pause & INTEN) == 0) {
/*
* Our interrupt is not enabled on the chip
* and may be disabled for re-entrancy reasons,
* so just return. This is likely just a shared
* interrupt.
*/
return (0);
}
/*
* Instead of directly reading the interrupt status register,
* infer the cause of the interrupt by checking our in-core
* completion queues. This avoids a costly PCI bus read in
* most cases.
*/
if ((ahd->flags & AHD_ALL_INTERRUPTS) == 0
&& (ahd_check_cmdcmpltqueues(ahd) != 0))
intstat = CMDCMPLT;
else
intstat = ahd_inb(ahd, INTSTAT);
if ((intstat & INT_PEND) == 0)
return (0);
if (intstat & CMDCMPLT) {
ahd_outb(ahd, CLRINT, CLRCMDINT);
/*
* Ensure that the chip sees that we've cleared
* this interrupt before we walk the output fifo.
* Otherwise, we may, due to posted bus writes,
* clear the interrupt after we finish the scan,
* and after the sequencer has added new entries
* and asserted the interrupt again.
*/
if ((ahd->bugs & AHD_INTCOLLISION_BUG) != 0) {
if (ahd_is_paused(ahd)) {
/*
* Potentially lost SEQINT.
* If SEQINTCODE is non-zero,
* simulate the SEQINT.
*/
if (ahd_inb(ahd, SEQINTCODE) != NO_SEQINT)
intstat |= SEQINT;
}
} else {
ahd_flush_device_writes(ahd);
}
ahd_run_qoutfifo(ahd);
ahd->cmdcmplt_counts[ahd->cmdcmplt_bucket]++;
ahd->cmdcmplt_total++;
#ifdef AHD_TARGET_MODE
if ((ahd->flags & AHD_TARGETROLE) != 0)
ahd_run_tqinfifo(ahd, /*paused*/FALSE);
#endif
}
/*
* Handle statuses that may invalidate our cached
* copy of INTSTAT separately.
*/
if (intstat == 0xFF && (ahd->features & AHD_REMOVABLE) != 0) {
/* Hot eject. Do nothing */
} else if (intstat & HWERRINT) {
ahd_handle_hwerrint(ahd);
} else if ((intstat & (PCIINT|SPLTINT)) != 0) {
ahd->bus_intr(ahd);
} else {
if ((intstat & SEQINT) != 0)
ahd_handle_seqint(ahd, intstat);
if ((intstat & SCSIINT) != 0)
ahd_handle_scsiint(ahd, intstat);
}
return (1);
}
#endif /* _AIC79XX_INLINE_H_ */
Reference in New Issue View Git Blame Copy Permalink