ab431312b4
ADMtek AL981 "Comet" chipset. The AL981 is yet another DEC tulip clone, except with simpler receive filter options. The AL981 has a built-in transceiver, power management support, wake on LAN and flow control. This chip performs extremely well; it's on par with the ASIX chipset in terms of speed, which is pretty good (it can do 11.5MB/sec with TCP easily). I would have committed this driver sooner, except I ran into one problem with the AL981 that required a workaround. When the chip is transmitting at full speed, it will sometimes wedge if you queue a series of packets that wrap from the end of the transmit descriptor list back to the beginning. I can't explain why this happens, and none of the other tulip clones behave this way. The workaround this is to just watch for the end of the transmit ring and make sure that al_start() breaks out of its packet queuing loop and waiting until the current batch of transmissions completes before wrapping back to the start of the ring. Fortunately, this does not significantly impact transmit performance. This is one of those things that takes weeks of analysis just to come up with two or three lines of code changes.
153 lines
5.4 KiB
Groff
153 lines
5.4 KiB
Groff
.\" Copyright (c) 1997, 1998, 1999
|
|
.\" Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
|
|
.\"
|
|
.\" Redistribution and use in source and binary forms, with or without
|
|
.\" modification, are permitted provided that the following conditions
|
|
.\" are met:
|
|
.\" 1. Redistributions of source code must retain the above copyright
|
|
.\" notice, this list of conditions and the following disclaimer.
|
|
.\" 2. Redistributions in binary form must reproduce the above copyright
|
|
.\" notice, this list of conditions and the following disclaimer in the
|
|
.\" documentation and/or other materials provided with the distribution.
|
|
.\" 3. All advertising materials mentioning features or use of this software
|
|
.\" must display the following acknowledgement:
|
|
.\" This product includes software developed by Bill Paul.
|
|
.\" 4. Neither the name of the author nor the names of any co-contributors
|
|
.\" may be used to endorse or promote products derived from this software
|
|
.\" without specific prior written permission.
|
|
.\"
|
|
.\" THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
|
|
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
.\" ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
|
|
.\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
.\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
.\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
.\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
.\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
|
|
.\" THE POSSIBILITY OF SUCH DAMAGE.
|
|
.\"
|
|
.\" $Id$
|
|
.\"
|
|
.Dd May 20, 1999
|
|
.Dt AL 4 i386
|
|
.Os FreeBSD
|
|
.Sh NAME
|
|
.Nm al
|
|
.Nd
|
|
ADMtek Inc. AL981 Comet fast ethernet device driver
|
|
.Sh SYNOPSIS
|
|
.Cd "device al0"
|
|
.Sh DESCRIPTION
|
|
The
|
|
.Nm
|
|
driver provides support for PCI ethernet adapters and embedded
|
|
controllers based on the ADMtek Inc. AL981 Comet fast ethernet
|
|
controller chip.
|
|
.Pp
|
|
The ADMtek chip uses bus master DMA and is designed to be a
|
|
DEC 21x4x workalike. The only major difference between the DEC
|
|
and ADMtek parts is that the AL981 receiver filter is programmed
|
|
using two special registers where as the DEC chip is programmed
|
|
by uploading a special setup frame via the transmit DMA engine.
|
|
The AL981 receive filter can only be programmed with a single
|
|
perfect filter entry for the local station address and a 64-bit
|
|
multicast hash table; the DEC filter has supports several other
|
|
options. The ADMtek fast ethernet controller supports both
|
|
10 and 100Mbps speeds in either full or half duplex using
|
|
an internal MII transceiver.
|
|
.Pp
|
|
The
|
|
.Nm
|
|
driver supports the following media types:
|
|
.Pp
|
|
.Bl -tag -width xxxxxxxxxxxxxxxxxxxx
|
|
.It autoselect
|
|
Enable autoselection of the media type and options.
|
|
The user can manually override
|
|
the autoselected mode by adding media options to the
|
|
.Pa /etc/rc.conf
|
|
fine.
|
|
.It 10baseT/UTP
|
|
Set 10Mbps operation. The
|
|
.Ar mediaopt
|
|
option can also be used to select either
|
|
.Ar full-duplex
|
|
or
|
|
.Ar half-duplex modes.
|
|
.It 100baseTX
|
|
Set 100Mbps (fast ethernet) operation. The
|
|
.Ar mediaopt
|
|
option can also be used to select either
|
|
.Ar full-duplex
|
|
or
|
|
.Ar half-duplex
|
|
modes.
|
|
.El
|
|
.Pp
|
|
The
|
|
.Nm
|
|
driver supports the following media options:
|
|
.Pp
|
|
.Bl -tag -width xxxxxxxxxxxxxxxxxxxx
|
|
.It full-duplex
|
|
Force full duplex operation
|
|
.It half-duplex
|
|
Force half duplex operation.
|
|
.El
|
|
.Pp
|
|
For more information on configuring this device, see
|
|
.Xr ifconfig 8 .
|
|
.Sh DIAGNOSTICS
|
|
.Bl -diag
|
|
.It "ax%d: couldn't map memory"
|
|
A fatal initialization error has occurred.
|
|
.It "ax%d: couldn't map interrupt"
|
|
A fatal initialization error has occurred.
|
|
.It "ax%d: watchdog timeout"
|
|
The device has stopped responding to the network, or there is a problem with
|
|
the network connection (cable).
|
|
.It "ax%d: no memory for rx list"
|
|
The driver failed to allocate an mbuf for the receiver ring.
|
|
.It "ax%d: no memory for tx list"
|
|
The driver failed to allocate an mbuf for the transmitter ring when
|
|
allocating a pad buffer or collapsing an mbuf chain into a cluster.
|
|
.It "ax%d: chip is in D3 power state -- setting to D0"
|
|
This message applies only to adapters which support power
|
|
management. Some operating systems place the controller in low power
|
|
mode when shutting down, and some PCI BIOSes fail to bring the chip
|
|
out of this state before configuring it. The controller loses all of
|
|
its PCI configuration in the D3 state, so if the BIOS does not set
|
|
it back to full power mode in time, it won't be able to configure it
|
|
correctly. The driver tries to detect this condition and bring
|
|
the adapter back to the D0 (full power) state, but this may not be
|
|
enough to return the driver to a fully operational condition. If
|
|
you see this message at boot time and the driver fails to attach
|
|
the device as a network interface, you will have to perform second
|
|
warm boot to have the device properly configured.
|
|
.Pp
|
|
Note that this condition only occurs when warm booting from another
|
|
operating system. If you power down your system prior to booting
|
|
.Fx ,
|
|
the card should be configured correctly.
|
|
.El
|
|
.Sh SEE ALSO
|
|
.Xr arp 4 ,
|
|
.Xr netintro 4 ,
|
|
.Xr ifconfig 8
|
|
.Rs
|
|
.%T ADMtek AL981 data sheet
|
|
.%O http://www.admtek.com.tw
|
|
.Re
|
|
.Sh HISTORY
|
|
The
|
|
.Nm
|
|
device driver first appeared in
|
|
.Fx 3.0 .
|
|
.Sh AUTHOR
|
|
The
|
|
.Nm
|
|
driver was written by
|
|
.An Bill Paul Aq wpaul@ctr.columbia.edu .
|