The existing scan code is based on sending an i2c START condition and if there is no error it assumes there is a device at that i2c address. Some i2c controllers don't support sending individual start/stop signals on the bus, they can only perform complete data transfers with start/stop handled in the silicon. This adds a fallback mechanism that attempts to read a single byte from each i2c address. It's less reliable than looking for an an ACK repsonse to a start, because some devices will NAK an attempt to read that isn't preceeded by a write of a register address. Writing to devices to probe them is too dangerous to even consider. The user is told that a less-reliable scan is being done, so even if the read-scan comes up empty too, it's still a vast improvement over the old situation where it would just claim there were no devices on the bus even though the devices were there and working fine. If the i2c controller responds with a proper ENODEV (device doesn't support operation) or an almost-proper EOPNOTSUPP, the START/STOP scan is switched to a read-scan right away. Most controllers respond with ENXIO or EIO if they don't support START/STOP, so no quick-out is available. For those, if a scan of all 127 addresses and come up empty, the scan is re-done using the read method. Reported by: Maxim Filimonov <che@bein.link> |
||
---|---|---|
bin | ||
cddl | ||
contrib | ||
crypto | ||
etc | ||
gnu | ||
include | ||
kerberos5 | ||
lib | ||
libexec | ||
release | ||
rescue | ||
sbin | ||
secure | ||
share | ||
sys | ||
targets | ||
tests | ||
tools | ||
usr.bin | ||
usr.sbin | ||
.arcconfig | ||
.arclint | ||
COPYRIGHT | ||
LOCKS | ||
MAINTAINERS | ||
Makefile | ||
Makefile.inc1 | ||
Makefile.libcompat | ||
ObsoleteFiles.inc | ||
README | ||
README.md | ||
UPDATING |
FreeBSD Source:
This is the top level of the FreeBSD source directory. This file
was last revised on:
FreeBSD
For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information).
The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree. See build(7) and http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables.
The buildkernel
and installkernel
targets build and install
the kernel and the modules (see below). Please see the top of
the Makefile in this directory for more information on the
standard build targets and compile-time flags.
Building a kernel is a somewhat more involved process. See build(7), config(8), and http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html for more information.
Note: If you want to build and install the kernel with the
buildkernel
and installkernel
targets, you might need to build
world before. More information is available in the handbook.
The kernel configuration files reside in the sys/<arch>/conf
sub-directory. GENERIC is the default configuration used in release builds.
NOTES contains entries and documentation for all possible
devices, not just those commonly used.
Source Roadmap:
bin System/user commands.
cddl Various commands and libraries under the Common Development
and Distribution License.
contrib Packages contributed by 3rd parties.
crypto Cryptography stuff (see crypto/README).
etc Template files for /etc.
gnu Various commands and libraries under the GNU Public License.
Please see gnu/COPYING* for more information.
include System include files.
kerberos5 Kerberos5 (Heimdal) package.
lib System libraries.
libexec System daemons.
release Release building Makefile & associated tools.
rescue Build system for statically linked /rescue utilities.
sbin System commands.
secure Cryptographic libraries and commands.
share Shared resources.
sys Kernel sources.
tests Regression tests which can be run by Kyua. See tests/README
for additional information.
tools Utilities for regression testing and miscellaneous tasks.
usr.bin User commands.
usr.sbin System administration commands.
For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see:
http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html