freebsd-dev/sys/dev/mii/e1000phyreg.h
Pyun YongHyeon fcb62a8b01 Add hack to pass controller specific information to phy driver.
Unlike most other PHYs there is no easy way to know which media
type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now
passed via bus-specific instance variable of a device. While I'm
here add 88E1112 specific work around to set SIGDET polarity low.
Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly
gave remote access to system with DGE-560SX.
2009-09-28 21:03:28 +00:00

375 lines
14 KiB
C

/* $FreeBSD$ */
/*-
* Principal Author: Parag Patel
* Copyright (c) 2001
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice unmodified, this list of conditions, and the following
* disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* Additonal Copyright (c) 2001 by Traakan Software under same licence.
* Secondary Author: Matthew Jacob
*/
/*-
* Derived by information released by Intel under the following license:
*
* Copyright (c) 1999 - 2001, Intel Corporation
*
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
*
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* 3. Neither the name of Intel Corporation nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS''
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
* INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
*/
/*
* Marvell E1000 PHY registers
*/
#define E1000_MAX_REG_ADDRESS 0x1F
#define E1000_CR 0x00 /* control register */
#define E1000_CR_SPEED_SELECT_MSB 0x0040
#define E1000_CR_COLL_TEST_ENABLE 0x0080
#define E1000_CR_FULL_DUPLEX 0x0100
#define E1000_CR_RESTART_AUTO_NEG 0x0200
#define E1000_CR_ISOLATE 0x0400
#define E1000_CR_POWER_DOWN 0x0800
#define E1000_CR_AUTO_NEG_ENABLE 0x1000
#define E1000_CR_SPEED_SELECT_LSB 0x2000
#define E1000_CR_LOOPBACK 0x4000
#define E1000_CR_RESET 0x8000
#define E1000_CR_SPEED_1000 0x0040
#define E1000_CR_SPEED_100 0x2000
#define E1000_CR_SPEED_10 0x0000
#define E1000_SR 0x01 /* status register */
#define E1000_SR_EXTENDED 0x0001
#define E1000_SR_JABBER_DETECT 0x0002
#define E1000_SR_LINK_STATUS 0x0004
#define E1000_SR_AUTO_NEG 0x0008
#define E1000_SR_REMOTE_FAULT 0x0010
#define E1000_SR_AUTO_NEG_COMPLETE 0x0020
#define E1000_SR_PREAMBLE_SUPPRESS 0x0040
#define E1000_SR_EXTENDED_STATUS 0x0100
#define E1000_SR_100T2 0x0200
#define E1000_SR_100T2_FD 0x0400
#define E1000_SR_10T 0x0800
#define E1000_SR_10T_FD 0x1000
#define E1000_SR_100TX 0x2000
#define E1000_SR_100TX_FD 0x4000
#define E1000_SR_100T4 0x8000
#define E1000_ID1 0x02 /* ID register 1 */
#define E1000_ID2 0x03 /* ID register 2 */
#define E1000_ID_88E1000 0x01410C50
#define E1000_ID_88E1000S 0x01410C40
#define E1000_ID_88E1011 0x01410C20
#define E1000_ID_MASK 0xFFFFFFF0
#define E1000_AR 0x04 /* autonegotiation advertise reg */
#define E1000_AR_SELECTOR_FIELD 0x0001
#define E1000_AR_10T 0x0020
#define E1000_AR_10T_FD 0x0040
#define E1000_AR_100TX 0x0080
#define E1000_AR_100TX_FD 0x0100
#define E1000_AR_100T4 0x0200
#define E1000_AR_PAUSE 0x0400
#define E1000_AR_ASM_DIR 0x0800
#define E1000_AR_REMOTE_FAULT 0x2000
#define E1000_AR_NEXT_PAGE 0x8000
#define E1000_AR_SPEED_MASK 0x01E0
/* Autonegotiation register bits for fiber cards (Alaska Only!) */
#define E1000_FA_1000X_FD 0x0020
#define E1000_FA_1000X 0x0040
#define E1000_FA_SYM_PAUSE 0x0080
#define E1000_FA_ASYM_PAUSE 0x0100
#define E1000_FA_FAULT1 0x1000
#define E1000_FA_FAULT2 0x2000
#define E1000_FA_NEXT_PAGE 0x8000
#define E1000_LPAR 0x05 /* autoneg link partner abilities reg */
#define E1000_LPAR_SELECTOR_FIELD 0x0001
#define E1000_LPAR_10T 0x0020
#define E1000_LPAR_10T_FD 0x0040
#define E1000_LPAR_100TX 0x0080
#define E1000_LPAR_100TX_FD 0x0100
#define E1000_LPAR_100T4 0x0200
#define E1000_LPAR_PAUSE 0x0400
#define E1000_LPAR_ASM_DIR 0x0800
#define E1000_LPAR_REMOTE_FAULT 0x2000
#define E1000_LPAR_ACKNOWLEDGE 0x4000
#define E1000_LPAR_NEXT_PAGE 0x8000
/* autoneg link partner ability register bits for fiber cards (Alaska Only!) */
#define E1000_FPAR_1000X_FD 0x0020
#define E1000_FPAR_1000X 0x0040
#define E1000_FPAR_SYM_PAUSE 0x0080
#define E1000_FPAR_ASYM_PAUSE 0x0100
#define E1000_FPAR_FAULT1 0x1000
#define E1000_FPAR_FAULT2 0x2000
#define E1000_FPAR_ACK 0x4000
#define E1000_FPAR_NEXT_PAGE 0x8000
#define E1000_ER 0x06 /* autoneg expansion reg */
#define E1000_ER_LP_NWAY 0x0001
#define E1000_ER_PAGE_RXD 0x0002
#define E1000_ER_NEXT_PAGE 0x0004
#define E1000_ER_LP_NEXT_PAGE 0x0008
#define E1000_ER_PAR_DETECT_FAULT 0x0100
#define E1000_NPTX 0x07 /* autoneg next page TX */
#define E1000_NPTX_MSG_CODE_FIELD 0x0001
#define E1000_NPTX_TOGGLE 0x0800
#define E1000_NPTX_ACKNOWLDGE2 0x1000
#define E1000_NPTX_MSG_PAGE 0x2000
#define E1000_NPTX_NEXT_PAGE 0x8000
#define E1000_RNPR 0x08 /* autoneg link-partner (?) next page */
#define E1000_RNPR_MSG_CODE_FIELD 0x0001
#define E1000_RNPR_TOGGLE 0x0800
#define E1000_RNPR_ACKNOWLDGE2 0x1000
#define E1000_RNPR_MSG_PAGE 0x2000
#define E1000_RNPR_ACKNOWLDGE 0x4000
#define E1000_RNPR_NEXT_PAGE 0x8000
#define E1000_1GCR 0x09 /* 1000T (1G) control reg */
#define E1000_1GCR_ASYM_PAUSE 0x0080
#define E1000_1GCR_1000T 0x0100
#define E1000_1GCR_1000T_FD 0x0200
#define E1000_1GCR_REPEATER_DTE 0x0400
#define E1000_1GCR_MS_VALUE 0x0800
#define E1000_1GCR_MS_ENABLE 0x1000
#define E1000_1GCR_TEST_MODE_NORMAL 0x0000
#define E1000_1GCR_TEST_MODE_1 0x2000
#define E1000_1GCR_TEST_MODE_2 0x4000
#define E1000_1GCR_TEST_MODE_3 0x6000
#define E1000_1GCR_TEST_MODE_4 0x8000
#define E1000_1GCR_SPEED_MASK 0x0300
#define E1000_1GSR 0x0A /* 1000T (1G) status reg */
#define E1000_1GSR_IDLE_ERROR_CNT 0x0000
#define E1000_1GSR_ASYM_PAUSE_DIR 0x0100
#define E1000_1GSR_LP 0x0400
#define E1000_1GSR_LP_FD 0x0800
#define E1000_1GSR_REMOTE_RX_STATUS 0x1000
#define E1000_1GSR_LOCAL_RX_STATUS 0x2000
#define E1000_1GSR_MS_CONFIG_RES 0x4000
#define E1000_1GSR_MS_CONFIG_FAULT 0x8000
#define E1000_ESR 0x0F /* IEEE extended status reg */
#define E1000_ESR_1000T 0x1000
#define E1000_ESR_1000T_FD 0x2000
#define E1000_ESR_1000X 0x4000
#define E1000_ESR_1000X_FD 0x8000
#define E1000_TX_POLARITY_MASK 0x0100
#define E1000_TX_NORMAL_POLARITY 0
#define E1000_AUTO_POLARITY_DISABLE 0x0010
#define E1000_SCR 0x10 /* special control register */
#define E1000_SCR_JABBER_DISABLE 0x0001
#define E1000_SCR_POLARITY_REVERSAL 0x0002
#define E1000_SCR_SQE_TEST 0x0004
#define E1000_SCR_INT_FIFO_DISABLE 0x0008
#define E1000_SCR_CLK125_DISABLE 0x0010
#define E1000_SCR_MDI_MANUAL_MODE 0x0000
#define E1000_SCR_MDIX_MANUAL_MODE 0x0020
#define E1000_SCR_AUTO_X_1000T 0x0040
#define E1000_SCR_AUTO_X_MODE 0x0060
#define E1000_SCR_10BT_EXT_ENABLE 0x0080
#define E1000_SCR_MII_5BIT_ENABLE 0x0100
#define E1000_SCR_SCRAMBLER_DISABLE 0x0200
#define E1000_SCR_FORCE_LINK_GOOD 0x0400
#define E1000_SCR_ASSERT_CRS_ON_TX 0x0800
#define E1000_SCR_RX_FIFO_DEPTH_6 0x0000
#define E1000_SCR_RX_FIFO_DEPTH_8 0x1000
#define E1000_SCR_RX_FIFO_DEPTH_10 0x2000
#define E1000_SCR_RX_FIFO_DEPTH_12 0x3000
#define E1000_SCR_TX_FIFO_DEPTH_6 0x0000
#define E1000_SCR_TX_FIFO_DEPTH_8 0x4000
#define E1000_SCR_TX_FIFO_DEPTH_10 0x8000
#define E1000_SCR_TX_FIFO_DEPTH_12 0xC000
/* 88E3016 only */
#define E1000_SCR_AUTO_MDIX 0x0030
#define E1000_SCR_SIGDET_POLARITY 0x0040
#define E1000_SCR_EXT_DISTANCE 0x0080
#define E1000_SCR_FEFI_DISABLE 0x0100
#define E1000_SCR_NLP_GEN_DISABLE 0x0800
#define E1000_SCR_LPNP 0x1000
#define E1000_SCR_NLP_CHK_DISABLE 0x2000
#define E1000_SCR_EN_DETECT 0x4000
#define E1000_SCR_EN_DETECT_MASK 0x0300
/* 88E1112 page 1 fiber specific control */
#define E1000_SCR_FIB_TX_DIS 0x0008
#define E1000_SCR_FIB_SIGDET_POLARITY 0x0200
#define E1000_SCR_FIB_FORCE_LINK 0x0400
/* 88E1112 page 2 */
#define E1000_SCR_MODE_MASK 0x0380
#define E1000_SCR_MODE_AUTO 0x0180
#define E1000_SCR_MODE_COPPER 0x0280
#define E1000_SCR_MODE_1000BX 0x0380
/* 88E1116 page 0 */
#define E1000_SCR_POWER_DOWN 0x0004
/* 88E1116, 88E1149 page 2 */
#define E1000_SCR_RGMII_POWER_UP 0x0008
/* 88E1116, 88E1149 page 3 */
#define E1000_SCR_LED_STAT0_MASK 0x000F
#define E1000_SCR_LED_STAT1_MASK 0x00F0
#define E1000_SCR_LED_INIT_MASK 0x0F00
#define E1000_SCR_LED_LOS_MASK 0xF000
#define E1000_SCR_LED_STAT0(x) ((x) & E1000_SCR_LED_STAT0_MASK)
#define E1000_SCR_LED_STAT1(x) ((x) & E1000_SCR_LED_STAT1_MASK)
#define E1000_SCR_LED_INIT(x) ((x) & E1000_SCR_LED_INIT_MASK)
#define E1000_SCR_LED_LOS(x) ((x) & E1000_SCR_LED_LOS_MASK)
#define E1000_SSR 0x11 /* special status register */
#define E1000_SSR_JABBER 0x0001
#define E1000_SSR_REV_POLARITY 0x0002
#define E1000_SSR_MDIX 0x0020
#define E1000_SSR_LINK 0x0400
#define E1000_SSR_SPD_DPLX_RESOLVED 0x0800
#define E1000_SSR_PAGE_RCVD 0x1000
#define E1000_SSR_DUPLEX 0x2000
#define E1000_SSR_SPEED 0xC000
#define E1000_SSR_10MBS 0x0000
#define E1000_SSR_100MBS 0x4000
#define E1000_SSR_1000MBS 0x8000
#define E1000_IER 0x12 /* interrupt enable reg */
#define E1000_IER_JABBER 0x0001
#define E1000_IER_POLARITY_CHANGE 0x0002
#define E1000_IER_MDIX_CHANGE 0x0040
#define E1000_IER_FIFO_OVER_UNDERUN 0x0080
#define E1000_IER_FALSE_CARRIER 0x0100
#define E1000_IER_SYMBOL_ERROR 0x0200
#define E1000_IER_LINK_STAT_CHANGE 0x0400
#define E1000_IER_AUTO_NEG_COMPLETE 0x0800
#define E1000_IER_PAGE_RECEIVED 0x1000
#define E1000_IER_DUPLEX_CHANGED 0x2000
#define E1000_IER_SPEED_CHANGED 0x4000
#define E1000_IER_AUTO_NEG_ERR 0x8000
/* 88E1116, 88E1149 page 3, LED timer control. */
#define E1000_PULSE_MASK 0x7000
#define E1000_PULSE_NO_STR 0 /* no pulse stretching */
#define E1000_PULSE_21MS 1 /* 21 ms to 42 ms */
#define E1000_PULSE_42MS 2 /* 42 ms to 84 ms */
#define E1000_PULSE_84MS 3 /* 84 ms to 170 ms */
#define E1000_PULSE_170MS 4 /* 170 ms to 340 ms */
#define E1000_PULSE_340MS 5 /* 340 ms to 670 ms */
#define E1000_PULSE_670MS 6 /* 670 ms to 1300 ms */
#define E1000_PULSE_1300MS 7 /* 1300 ms to 2700 ms */
#define E1000_PULSE_DUR(x) ((x) & E1000_PULSE_MASK)
#define E1000_BLINK_MASK 0x0700
#define E1000_BLINK_42MS 0 /* 42 ms */
#define E1000_BLINK_84MS 1 /* 84 ms */
#define E1000_BLINK_170MS 2 /* 170 ms */
#define E1000_BLINK_340MS 3 /* 340 ms */
#define E1000_BLINK_670MS 4 /* 670 ms */
#define E1000_BLINK_RATE(x) ((x) & E1000_BLINK_MASK)
#define E1000_ISR 0x13 /* interrupt status reg */
#define E1000_ISR_JABBER 0x0001
#define E1000_ISR_POLARITY_CHANGE 0x0002
#define E1000_ISR_MDIX_CHANGE 0x0040
#define E1000_ISR_FIFO_OVER_UNDERUN 0x0080
#define E1000_ISR_FALSE_CARRIER 0x0100
#define E1000_ISR_SYMBOL_ERROR 0x0200
#define E1000_ISR_LINK_STAT_CHANGE 0x0400
#define E1000_ISR_AUTO_NEG_COMPLETE 0x0800
#define E1000_ISR_PAGE_RECEIVED 0x1000
#define E1000_ISR_DUPLEX_CHANGED 0x2000
#define E1000_ISR_SPEED_CHANGED 0x4000
#define E1000_ISR_AUTO_NEG_ERR 0x8000
#define E1000_ESCR 0x14 /* extended special control reg */
#define E1000_ESCR_FIBER_LOOPBACK 0x4000
#define E1000_ESCR_DOWN_NO_IDLE 0x8000
#define E1000_ESCR_TX_CLK_2_5 0x0060
#define E1000_ESCR_TX_CLK_25 0x0070
#define E1000_ESCR_TX_CLK_0 0x0000
#define E1000_RECR 0x15 /* RX error counter reg */
#define E1000_EADR 0x16 /* extended address reg */
#define E1000_LCR 0x18 /* LED control reg */
#define E1000_LCR_LED_TX 0x0001
#define E1000_LCR_LED_RX 0x0002
#define E1000_LCR_LED_DUPLEX 0x0004
#define E1000_LCR_LINK 0x0008
#define E1000_LCR_BLINK_42MS 0x0000
#define E1000_LCR_BLINK_84MS 0x0100
#define E1000_LCR_BLINK_170MS 0x0200
#define E1000_LCR_BLINK_340MS 0x0300
#define E1000_LCR_BLINK_670MS 0x0400
#define E1000_LCR_PULSE_OFF 0x0000
#define E1000_LCR_PULSE_21_42MS 0x1000
#define E1000_LCR_PULSE_42_84MS 0x2000
#define E1000_LCR_PULSE_84_170MS 0x3000
#define E1000_LCR_PULSE_170_340MS 0x4000
#define E1000_LCR_PULSE_340_670MS 0x5000
#define E1000_LCR_PULSE_670_13S 0x6000
#define E1000_LCR_PULSE_13_26S 0x7000
/* The following register is found only on the 88E1011 Alaska PHY */
#define E1000_ESSR 0x1B /* Extended PHY specific sts */
#define E1000_ESSR_FIBER_LINK 0x2000
#define E1000_ESSR_GMII_COPPER 0x000f
#define E1000_ESSR_GMII_FIBER 0x0007
#define E1000_ESSR_TBI_COPPER 0x000d
#define E1000_ESSR_TBI_FIBER 0x0005