c1f3e4bf21
cd src/share; find man[1-9] -type f|xargs perl -pi -e 's/[ \t]+$//' BTW, what editors are the culprits? I'm using vim and it shows me whitespace at EOL in troff files with a thick blue block... Reviewed by: Silence from cvs diff -b MFC after: 7 days
92 lines
3.1 KiB
Groff
92 lines
3.1 KiB
Groff
.\"
|
|
.\" Copyright (c) 1994, Wilko Bulte
|
|
.\" All rights reserved.
|
|
.\"
|
|
.\" $FreeBSD$
|
|
.\"
|
|
.Dd September 23, 1994
|
|
.Dt IE 4 i386
|
|
.Os
|
|
.Sh NAME
|
|
.Nm ie
|
|
.Nd ethernet device driver
|
|
.Sh SYNOPSIS
|
|
.Cd "device ie0 at isa? port 0x360 irq 7 iomem 0xd0000"
|
|
.Sh DESCRIPTION
|
|
The
|
|
.Nm
|
|
driver provides support for 8 and 16bit ISA ethernet cards that are based on
|
|
the Intel i82586 chip.
|
|
It supports the AT&T Starlan 10 and Starlan Fiber,
|
|
the EN100, the Intel EtherExpress 16, the 3COM 3C507 and the RACAL Interlan
|
|
NI5210.
|
|
.Sh DIAGNOSTICS
|
|
.Bl -diag
|
|
.It "ie%d: unknown board type code %d"
|
|
An i82586 chip was found, but the driver was unable to determine the actual
|
|
board type during the probe.
|
|
.It "ie%d: kernel configured maddr %x doesn't match board configured maddr %x"
|
|
The device probe detected a different maddr than the one specified in the
|
|
kernel configuration file.
|
|
.It "ie%d: can't find shared memory"
|
|
The device probe could not access the shared memory to determine its size.
|
|
.It "ie%d: kernel configured msize %d doesn't match board configured msize %d"
|
|
The device probe found a different size for the shared memory than the one
|
|
specified in the kernel configuration file.
|
|
.It "ie%d: kernel configured irq %d doesn't match board configured irq %d"
|
|
The device probe detected that the board is configured for a different
|
|
interrupt than the one specified in the kernel configuration file.
|
|
.It "ie%d: reset"
|
|
The Intel i82586 had to be reset by the driver.
|
|
.It "ie%d: transceiver problem"
|
|
The driver has detected a problem with the ethernet transceiver.
|
|
This is
|
|
usually due to a loose or broken transceiver cable when using an external
|
|
transceiver.
|
|
When you experience this problem with an on-card transceiver
|
|
your card may be incorrectly jumpered for to use an external transceiver.
|
|
Worst case your on-board transceiver may be broken.
|
|
.It "ie%d: TDR detected an open %d clocks away"
|
|
The driver detected an open circuit in the ethernet cable.
|
|
Check your
|
|
coax cable and terminator resistors.
|
|
.It "ie%d: TDR detected a short %d clocks away"
|
|
The driver detected a short circuit in the ethernet cable.
|
|
Check your
|
|
coax cable and terminator resistors.
|
|
.It "ie%d: TDR returned unknown status %x"
|
|
The driver got an unknown status from the card during the ethernet cable
|
|
test.
|
|
.It "ie%d: multicast address setup command failed"
|
|
The card could not be put into multicast mode.
|
|
.It "ie%d: configure command failed"
|
|
The card refused to respond correctly during configuration.
|
|
.It "ie%d: individual address setup command failed"
|
|
The programming of the Ethernet (MAC) address failed.
|
|
.El
|
|
.Sh CAVEATS
|
|
The Racal Interlan NI5210 comes in variants with 8 and 16 kbytes of
|
|
shared memory.
|
|
It is strongly advisable to use the 16 kbyte variant.
|
|
You can upgrade your 8 kbyte card to 16 kbyte by adding an additional
|
|
RAM chip.
|
|
.Sh SEE ALSO
|
|
.Xr arp 4 ,
|
|
.Xr netintro 4 ,
|
|
.Xr ng_ether 4 ,
|
|
.Xr ifconfig 8
|
|
.Sh AUTHORS
|
|
.An -nosplit
|
|
The
|
|
.Nm
|
|
device driver was written by
|
|
.An Garrett A. Wollman ,
|
|
based on code by
|
|
.An William F. Jolitz
|
|
and Lawrence Berkeley Laboratories.
|
|
.Tn 3C507
|
|
support was written by
|
|
.An Charles M. Hannum .
|
|
This manual page was written by
|
|
.An Wilko C. Bulte .
|