freebsd-dev/sys/dev/mii/nsphyreg.h
2010-03-03 17:55:51 +00:00

109 lines
4.3 KiB
C

/* $NetBSD: nsphyreg.h,v 1.1 1998/08/10 23:58:39 thorpej Exp $ */
/*-
* Copyright (c) 1998 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
* NASA Ames Research Center.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*
* $FreeBSD$
*/
#ifndef _DEV_MII_NSPHYREG_H_
#define _DEV_MII_NSPHYREG_H_
/*
* DP83840 registers.
*/
#define MII_NSPHY_DCR 0x12 /* Disconnect counter */
#define MII_NSPHY_FCSCR 0x13 /* False carrier sense counter */
#define MII_NSPHY_RECR 0x15 /* Receive error counter */
#define MII_NSPHY_SRR 0x16 /* Silicon revision */
#define MII_NSPHY_PCR 0x17 /* PCS sub-layer configuration */
#define PCR_NRZI 0x8000 /* NRZI encoding enabled for 100TX */
#define PCR_DESCRTOSEL 0x4000 /* descrambler t/o select (2ms) */
#define PCR_DESCRTODIS 0x2000 /* descrambler t/o disable */
#define PCR_REPEATER 0x1000 /* repeater mode */
#define PCR_ENCSEL 0x0800 /* encoder mode select */
#define PCR_CLK25MDIS 0x0080 /* CLK25M disable */
#define PCR_FLINK100 0x0040 /* force good link in 100mbps */
#define PCR_CIMDIS 0x0020 /* carrier integrity monitor disable */
#define PCR_TXOFF 0x0010 /* force transmit off */
#define PCR_LED1MODE 0x0004 /* LED1 mode: see below */
#define PCR_LED4MODE 0x0002 /* LED4 mode: see below */
/*
* LED1 Mode:
*
* 1 LED1 output configured to PAR's CON_STATUS, useful for
* network management in 100baseTX mode.
*
* 0 Normal LED1 operation - 10baseTX and 100baseTX transmission
* activity.
*
* LED4 Mode:
*
* 1 LED4 output configured to indicate full-duplex in both
* 10baseT and 100baseTX modes.
*
* 0 LED4 output configured to indicate polarity in 10baseT
* mode and full-duplex in 100baseTX mode.
*/
#define MII_NSPHY_LBREMR 0x18 /* Loopback, bypass, error mask */
#define LBREMR_BADSSDEN 0x8000 /* enable bad SSD detection */
#define LBREMR_BP4B5B 0x4000 /* bypass 4b/5b encoding */
#define LBREMR_BPSCR 0x2000 /* bypass scrambler */
#define LBREMR_BPALIGN 0x1000 /* bypass alignment function */
#define LBREMR_10LOOP 0x0800 /* 10baseT loopback */
#define LBREMR_LB1 0x0200 /* loopback ctl 1 */
#define LBREMR_LB0 0x0100 /* loopback ctl 0 */
#define LBREMR_ALTCRS 0x0040 /* alt crs operation */
#define LBREMR_LOOPXMTDIS 0x0020 /* disable transmit in 100TX loopbk */
#define LBREMR_CODEERR 0x0010 /* code errors */
#define LBREMR_PEERR 0x0008 /* premature end errors */
#define LBREMR_LINKERR 0x0004 /* link errors */
#define LBREMR_PKTERR 0x0002 /* packet errors */
#define MII_NSPHY_PAR 0x19 /* Physical address and status */
#define PAR_DISCRSJAB 0x0800 /* disable car sense during jab */
#define PAR_ANENSTAT 0x0400 /* autoneg mode status */
#define PAR_FEFIEN 0x0100 /* far end fault enable */
#define PAR_FDX 0x0080 /* full duplex status */
#define PAR_10 0x0040 /* 10mbps mode */
#define PAR_CON 0x0020 /* connect status */
#define PAR_AMASK 0x001f /* PHY address bits */
#define MII_NSPHY_10BTSR 0x1b /* 10baseT status */
#define MII_NSPHY_10BTCR 0x1c /* 10baseT configuration */
#endif /* _DEV_MII_NSPHYREG_H_ */