freebsd-nq/sys/mips/conf/TL-WR1043NDv2.hints

# The TP-Link 1043NDv2 is based on the AP135 with a couple of minor
# differences - well, besides having no 11ac.

# $FreeBSD$

# QCA955X_ETH_CFG_RGMII_EN (1 << 0)
hint.qca955x_gmac.0.gmac_cfg=0x1

# Use base mac address for wifi; +1 and +2 for arge0/arge1.
hint.ar71xx.0.eeprom_mac_addr=0x1f01fc00
hint.ar71xx.0.eeprom_mac_isascii=0

hint.ar71xx_mac_map.0.devid=ath
hint.ar71xx_mac_map.0.unitid=0
hint.ar71xx_mac_map.0.offset=0
hint.ar71xx_mac_map.0.is_local=0

hint.ar71xx_mac_map.1.devid=arge
hint.ar71xx_mac_map.1.unitid=0
hint.ar71xx_mac_map.1.offset=1
hint.ar71xx_mac_map.1.is_local=0

hint.ar71xx_mac_map.2.devid=arge
hint.ar71xx_mac_map.2.unitid=1
hint.ar71xx_mac_map.2.offset=2
hint.ar71xx_mac_map.2.is_local=0

# mdiobus0 on arge0
hint.argemdio.0.at="nexus0"
hint.argemdio.0.maddr=0x19000000
hint.argemdio.0.msize=0x1000
hint.argemdio.0.order=0

# mdiobus1 on arge1 - required to bring up arge1?
hint.argemdio.1.at="nexus0"
hint.argemdio.1.maddr=0x1a000000
hint.argemdio.1.msize=0x1000
hint.argemdio.1.order=0

# AR8327 - connected via mdiobus0 on arge0
hint.arswitch.0.at="mdio0"
hint.arswitch.0.is_7240=0	# definitely not the internal switch!
hint.arswitch.0.is_9340=0	# not the internal switch!
hint.arswitch.0.numphys=5	# all ports are PHYs
hint.arswitch.0.phy4cpu=0
hint.arswitch.0.is_rgmii=0	# not needed
hint.arswitch.0.is_gmii=0	# not needed

# This is where it gets a bit odd. port 0 and port 6 are CPU ports.
# The current code only supports one CPU port.  So hm, what should
# we do to hook PAD6 up to be RGMII but a PHY, not a MAC?

# The other trick - how do we get arge1 (hooked up to GMAC0) to work?
# That's currently supposed to be hooked up to CPU port 0.

# Other AR8327 configuration parameters

# AP136-020 parameters

# GMAC0 AR8327 -> GMAC1 (arge1) SoC, SGMII

# AR8327_PAD_MAC_SGMII
hint.arswitch.0.pad.0.mode=3
#hint.arswitch.0.pad.0.rxclk_delay_sel=0
hint.arswitch.0.pad.0.sgmii_delay_en=1

# GMAC6 AR8327 -> GMAC0 (arge0) SoC, RGMII

# AR8327_PAD_MAC_RGMII
hint.arswitch.0.pad.6.mode=6
hint.arswitch.0.pad.6.txclk_delay_en=1
hint.arswitch.0.pad.6.rxclk_delay_en=1
# AR8327_CLK_DELAY_SEL1
hint.arswitch.0.pad.6.txclk_delay_sel=1
# AR8327_CLK_DELAY_SEL2
hint.arswitch.0.pad.6.rxclk_delay_sel=2

hint.arswitch.0.led.ctrl0=0xcc35cc35
hint.arswitch.0.led.ctrl1=0xca35ca35
hint.arswitch.0.led.ctrl2=0xc935c935
hint.arswitch.0.led.ctrl3=0x03ffff00
int.arswitch.0.led.open_drain=1

# force_link=1 is required for the rest of the parameters
# to be configured.
hint.arswitch.0.port.0.force_link=1
hint.arswitch.0.port.0.speed=1000
hint.arswitch.0.port.0.duplex=1
hint.arswitch.0.port.0.txpause=1
hint.arswitch.0.port.0.rxpause=1

# force_link=1 is required for the rest of the parameters
# to be configured.
hint.arswitch.0.port.6.force_link=1
hint.arswitch.0.port.6.speed=1000
hint.arswitch.0.port.6.duplex=1
hint.arswitch.0.port.6.txpause=1
hint.arswitch.0.port.6.rxpause=1

# arge0 - hooked up to AR8327 GMAC6, RGMII
# set at 1000/full to the switch.
# so, lock both sides of this connect up to 1000/full;
# if_arge thus wont change the PLL configuration
# upon a link status change.
hint.arge.0.phymask=0x0
hint.arge.0.miimode=3           # RGMII
hint.arge.0.media=1000
hint.arge.0.fduplex=1
hint.arge.0.pll_1000=0x56000000

# arge1 - lock up to 1000/full
hint.arge.1.phymask=0x0
hint.arge.1.media=1000
hint.arge.1.fduplex=1
hint.arge.1.miimode=5		# SGMII
hint.arge.1.pll_1000=0x03000101

# hint.arge.1.eeprommac=0x1f01fc06

# ath0: Where the ART is - last 64k in the flash
hint.ath.0.eepromaddr=0x1fff0000
hint.ath.0.eepromsize=16384

# 128 KiB u-boot
hint.map.0.at="flash/spi0"
hint.map.0.start=0x00000000
hint.map.0.end=0x00020000	# 128k u-boot
hint.map.0.name="u-boot"
hint.map.0.readonly=1

# The TP-Link firmware will put the kernel first (variable size);
# then the rootfs will be placed hopefully at a 64KiB alignment
# by whatever calls mktplinkfw.

hint.map.1.at="flash/spi0"
hint.map.1.start=0x00020000
hint.map.1.end="search:0x00020000:0x10000:.!/bin/sh"
hint.map.1.name="kernel"
hint.map.1.readonly=1

hint.map.2.at="flash/spi0"
hint.map.2.start="search:0x00020000:0x10000:.!/bin/sh"
hint.map.2.end=0x007d0000
hint.map.2.name="rootfs"
hint.map.2.readonly=1

# 64KiB cfg
hint.map.3.at="flash/spi0"
hint.map.3.start=0x007d0000
hint.map.3.end=0x007e0000
hint.map.3.name="cfg"
hint.map.3.readonly=0

# 64KiB mib0
hint.map.4.at="flash/spi0"
hint.map.4.start=0x007e0000
hint.map.4.end=0x007f0000
hint.map.4.name="mib0"
hint.map.4.readonly=1

# 64KiB ART
hint.map.5.at="flash/spi0"
hint.map.5.start=0x007f0000
hint.map.5.end=0x00800000	# 64k ART
hint.map.5.name="ART"
hint.map.5.readonly=1