d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
0f822edead
freebsd-nq/sys/dev/puc/pucdata.c

1692 lines
40 KiB
C
Raw Normal View History

Start each of the license/copyright comments with /*-, minor shuffle of lines
2005-01-06 01:43:34 +00:00
/*-
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
* Copyright (c) 2006 Marcel Moolenaar
* All rights reserved.
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
*
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
/*
* PCI "universal" communications card driver configuration data (used to
* match/attach the cards).
*/
#include <sys/param.h>
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/bus.h>
Add MSI support to puc(9) Add support for MSI interrupts in the puc(9) driver. By default the driver will prefer MSI interrupts to legacy interrupts. A tunable, hw.puc.msi_disable, has been added to force the allocation of legacy interrupts. Reviewed by: jhb@ MFC after: 2 weeks Sponsored by: Sandvine Inc.
2014-03-13 15:57:25 +00:00
#include <sys/sysctl.h>
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
#include <machine/resource.h>
Need machine/bus.h here too
2006-06-12 19:22:44 +00:00
#include <machine/bus.h>
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
#include <sys/rman.h>
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
#include <dev/pci/pcivar.h>
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
#include <dev/puc/puc_bus.h>
#include <dev/puc/puc_cfg.h>
Fix building with GCC 4.2: ensure types are defined before refering to them.
2006-06-29 16:27:19 +00:00
#include <dev/puc/puc_bfe.h>
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static puc_config_f puc_config_amc;
static puc_config_f puc_config_diva;
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
static puc_config_f puc_config_exar;
Add support for Exar XR17V358 8-port serial device to puc(4) Reviewed by: marius Sponsored by: Sandvine Inc. MFC after: 1 week
2013-03-15 19:58:44 +00:00
static puc_config_f puc_config_exar_pcie;
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static puc_config_f puc_config_icbook;
- add support for CP-104EL-A and CP-104JU to puc PR: 151365 Submitted by: Joerg Niendorf <f5d10a@internode.on.net> Approved by: jhb
2011-11-11 22:24:16 +00:00
static puc_config_f puc_config_moxa;
All of Oxford/PLX OX16PCI954, OXm16PCI954 and OXu16PCI954 share the exact same (subsystem) device and vendor IDs. However, the reference design for the OXu16PCI954 uses a 14.7456 MHz clock (as does the EXSYS EX-41098-2 equipped with these), while at least the OX16PCI954 defaults to a 1.8432 MHz one. According to the datasheets of these chips, the only difference in PCI configuration space is that OXu16PCI954 have a revision ID of 1 while the other two are at 0. So employ the latter for determining the default clock rates of this family. Note that one might think that the actual clock could be derived from the Clock Prescaler Register (CPR) of these chips. Unfortunately, this is not that case and its use and content are orthogonal to the frequency of the crystal employed. Tested with an EXSYS EX-41098-2, which identifies and attaches as: pcib4@pci0:19:0:0: class=0x060400 card=0x02dd1014 chip=0x10801b21 rev=0x03 hdr=0x01 vendor = 'ASMedia Technology Inc.' device = 'ASM1083/1085 PCIe to PCI Bridge' class = bridge subclass = PCI-PCI puc0@pci0:20:4:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc1@pci0:20:4:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge puc2@pci0:20:8:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc3@pci0:20:8:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge pci20: <ACPI PCI bus> on pcib4 puc0: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5000-0x501f, 0x5020-0x503f mem 0xc6000000-0xc6000fff,0xc6001000-0xc6001fff irq 16 at device 4.0 on pci20 uart1: <16950 or compatible> at port 1 on puc0 uart2: <16950 or compatible> at port 2 on puc0 uart3: <16950 or compatible> at port 3 on puc0 uart4: <16950 or compatible> at port 4 on puc0 puc1: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x5040-0x505f,0x5060-0x507f mem 0xc6002000-0xc6002fff,0xc6003000-0xc6003fff irq 16 at device 4.1 on pci20 puc2: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5080-0x509f, 0x50a0-0x50bf mem 0xc6004000-0xc6004fff,0xc6005000-0xc6005fff irq 16 at device 8.0 on pci20 uart5: <16950 or compatible> at port 1 on puc2 uart6: <16950 or compatible> at port 2 on puc2 uart7: <16950 or compatible> at port 3 on puc2 uart8: <16950 or compatible> at port 4 on puc2 puc3: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x50c0-0x50df,0x50e0-0x50ff mem 0xc6006000-0xc6006fff,0xc6007000-0xc6007fff irq 16 at device 8.1 on pci20 MFC after: 2 weeks
2013-06-13 22:13:41 +00:00
static puc_config_f puc_config_oxford_pci954;
Some style fixes. Submitted by: bde
2011-06-06 15:33:15 +00:00
static puc_config_f puc_config_oxford_pcie;
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static puc_config_f puc_config_quatech;
static puc_config_f puc_config_syba;
static puc_config_f puc_config_siig;
Distinguish between the different variants and configurations of Sunix {MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S. Among others, this fixes the hang seen when trying to probe the none- existent second UART on an actually 1-port chip. Obtained from: NetBSD (BAR layouts) MFC after: 3 days Sponsored by: Bally Wulff Games & Entertainment GmbH
2014-04-08 07:32:32 +00:00
static puc_config_f puc_config_sunix;
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static puc_config_f puc_config_timedia;
static puc_config_f puc_config_titan;
const struct puc_cfg puc_pci_devices[] = {
{ 0x0009, 0x7168, 0xffff, 0,
"Sunix SUN1889",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, 8,
},
{ 0x103c, 0x1048, 0x103c, 0x1049,
"HP Diva Serial [GSP] Multiport UART - Tosca Console",
DEFAULT_RCLK,
PUC_PORT_3S, 0x10, 0, -1,
.config_function = puc_config_diva
},
{ 0x103c, 0x1048, 0x103c, 0x104a,
"HP Diva Serial [GSP] Multiport UART - Tosca Secondary",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 0, -1,
.config_function = puc_config_diva
},
{ 0x103c, 0x1048, 0x103c, 0x104b,
"HP Diva Serial [GSP] Multiport UART - Maestro SP2",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 0, -1,
.config_function = puc_config_diva
},
{ 0x103c, 0x1048, 0x103c, 0x1223,
"HP Diva Serial [GSP] Multiport UART - Superdome Console",
DEFAULT_RCLK,
PUC_PORT_3S, 0x10, 0, -1,
.config_function = puc_config_diva
},
{ 0x103c, 0x1048, 0x103c, 0x1226,
"HP Diva Serial [GSP] Multiport UART - Keystone SP2",
DEFAULT_RCLK,
PUC_PORT_3S, 0x10, 0, -1,
.config_function = puc_config_diva
},
{ 0x103c, 0x1048, 0x103c, 0x1282,
"HP Diva Serial [GSP] Multiport UART - Everest SP2",
DEFAULT_RCLK,
PUC_PORT_3S, 0x10, 0, -1,
.config_function = puc_config_diva
},
{ 0x10b5, 0x1076, 0x10b5, 0x1076,
"VScom PCI-800",
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x18, 0, 8,
},
{ 0x10b5, 0x1077, 0x10b5, 0x1077,
"VScom PCI-400",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x18, 0, 8,
},
{ 0x10b5, 0x1103, 0x10b5, 0x1103,
"VScom PCI-200",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x18, 4, 0,
Support the Comtrol RocketPort 550 PCi 16 (used with RocketPort I/F box). Sponsored by: Feral Software
2002-06-18 02:39:12 +00:00
},
Add support for Comtrol RocketPort 550 PCi models: 4 RJ45, 4 Quadcable, 8 RJ11, 8 Octacable, and 8 (used with RocketPort I/F box). Note: untested due to lack of hardware
2002-06-18 03:05:10 +00:00
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
/*
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
* Boca Research Turbo Serial 658 (8 serial port) card.
* Appears to be the same as Chase Research PLC PCI-FAST8
* and Perle PCI-FAST8 Multi-Port serial cards.
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
*/
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x10b5, 0x9050, 0x12e0, 0x0021,
"Boca Research Turbo Serial 658",
DEFAULT_RCLK * 4,
PUC_PORT_8S, 0x18, 0, 8,
},
{ 0x10b5, 0x9050, 0x12e0, 0x0031,
"Boca Research Turbo Serial 654",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x18, 0, 8,
},
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
/*
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
* Dolphin Peripherals 4035 (dual serial port) card. PLX 9050, with
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
* a seemingly-lame EEPROM setup that puts the Dolphin IDs
* into the subsystem fields, and claims that it's a
* network/misc (0x02/0x80) device.
*/
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x10b5, 0x9050, 0xd84d, 0x6808,
"Dolphin Peripherals 4035",
DEFAULT_RCLK,
PUC_PORT_2S, 0x18, 4, 0,
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
},
/*
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
* Dolphin Peripherals 4014 (dual parallel port) card. PLX 9050, with
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
* a seemingly-lame EEPROM setup that puts the Dolphin IDs
* into the subsystem fields, and claims that it's a
* network/misc (0x02/0x80) device.
*/
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x10b5, 0x9050, 0xd84d, 0x6810,
"Dolphin Peripherals 4014",
0,
PUC_PORT_2P, 0x20, 4, 0,
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x10e8, 0x818e, 0xffff, 0,
"Applied Micro Circuits 8 Port UART",
Add support for the NetMos NM9865 family of Serial/Parallel ports. Obtained from: NetMos MCS9865 v1.0.0.1 driver MFC after: 3 days
2009-12-07 20:05:02 +00:00
DEFAULT_RCLK,
PUC_PORT_8S, 0x14, -1, -1,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
.config_function = puc_config_amc
Add support for the NetMos NM9865 family of Serial/Parallel ports. Obtained from: NetMos MCS9865 v1.0.0.1 driver MFC after: 3 days
2009-12-07 20:05:02 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x11fe, 0x8010, 0xffff, 0,
"Comtrol RocketPort 550/8 RJ11 part A",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x11fe, 0x8011, 0xffff, 0,
"Comtrol RocketPort 550/8 RJ11 part B",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x11fe, 0x8012, 0xffff, 0,
"Comtrol RocketPort 550/8 Octa part A",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x11fe, 0x8013, 0xffff, 0,
"Comtrol RocketPort 550/8 Octa part B",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x11fe, 0x8014, 0xffff, 0,
"Comtrol RocketPort 550/4 RJ45",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x11fe, 0x8015, 0xffff, 0,
"Comtrol RocketPort 550/Quad",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x11fe, 0x8016, 0xffff, 0,
"Comtrol RocketPort 550/16 part A",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x11fe, 0x8017, 0xffff, 0,
"Comtrol RocketPort 550/16 part B",
DEFAULT_RCLK * 4,
PUC_PORT_12S, 0x10, 0, 8,
},
{ 0x11fe, 0x8018, 0xffff, 0,
"Comtrol RocketPort 550/8 part A",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x11fe, 0x8019, 0xffff, 0,
"Comtrol RocketPort 550/8 part B",
DEFAULT_RCLK * 4,
PUC_PORT_4S, 0x10, 0, 8,
},
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
Add support for the four PUC serial interfaces found on IBM SurePOS 300 series POS terminals. MFC after: 3 days Submitted by: Marc Balmer <marc at msys.ch>
2009-06-02 09:58:17 +00:00
/*
* IBM SurePOS 300 Series (481033H) serial ports
* Details can be found on the IBM RSS websites
*/
{ 0x1014, 0x0297, 0xffff, 0,
"IBM SurePOS 300 Series (481033H) serial ports",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0
},
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
/*
* SIIG Boards.
*
* SIIG provides documentation for their boards at:
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
* <URL:http://www.siig.com/downloads.asp>
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
*/
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x131f, 0x1010, 0xffff, 0,
"SIIG Cyber I/O PCI 16C550 (10x family)",
DEFAULT_RCLK,
PUC_PORT_1S1P, 0x18, 4, 0,
},
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x131f, 0x1011, 0xffff, 0,
"SIIG Cyber I/O PCI 16C650 (10x family)",
DEFAULT_RCLK,
PUC_PORT_1S1P, 0x18, 4, 0,
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x131f, 0x1012, 0xffff, 0,
"SIIG Cyber I/O PCI 16C850 (10x family)",
DEFAULT_RCLK,
PUC_PORT_1S1P, 0x18, 4, 0,
},
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x131f, 0x1021, 0xffff, 0,
"SIIG Cyber Parallel Dual PCI (10x family)",
0,
PUC_PORT_2P, 0x18, 8, 0,
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x131f, 0x1030, 0xffff, 0,
"SIIG Cyber Serial Dual PCI 16C550 (10x family)",
DEFAULT_RCLK,
PUC_PORT_2S, 0x18, 4, 0,
Support the Titan VScom PCI-200HV2 2 port serial card. MFC after: 3 days
2003-08-02 13:25:31 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x131f, 0x1031, 0xffff, 0,
"SIIG Cyber Serial Dual PCI 16C650 (10x family)",
DEFAULT_RCLK,
PUC_PORT_2S, 0x18, 4, 0,
Add an entry for the VScom (Titan?) PCI-800L 8-port serial multiport card. Thanks to bde for his help in configuring the undocumented bars in this driver... MFC after: 1 month
2003-09-19 19:55:08 +00:00
},
Support the Titan VScom PCI-200HV2 2 port serial card. MFC after: 3 days
2003-08-02 13:25:31 +00:00
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x131f, 0x1032, 0xffff, 0,
"SIIG Cyber Serial Dual PCI 16C850 (10x family)",
DEFAULT_RCLK,
PUC_PORT_2S, 0x18, 4, 0,
},
{ 0x131f, 0x1034, 0xffff, 0, /* XXX really? */
"SIIG Cyber 2S1P PCI 16C550 (10x family)",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x18, 4, 0,
},
{ 0x131f, 0x1035, 0xffff, 0, /* XXX really? */
"SIIG Cyber 2S1P PCI 16C650 (10x family)",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x18, 4, 0,
},
{ 0x131f, 0x1036, 0xffff, 0, /* XXX really? */
"SIIG Cyber 2S1P PCI 16C850 (10x family)",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x18, 4, 0,
},
{ 0x131f, 0x1050, 0xffff, 0,
"SIIG Cyber 4S PCI 16C550 (10x family)",
DEFAULT_RCLK,
PUC_PORT_4S, 0x18, 4, 0,
},
{ 0x131f, 0x1051, 0xffff, 0,
"SIIG Cyber 4S PCI 16C650 (10x family)",
DEFAULT_RCLK,
PUC_PORT_4S, 0x18, 4, 0,
},
{ 0x131f, 0x1052, 0xffff, 0,
"SIIG Cyber 4S PCI 16C850 (10x family)",
DEFAULT_RCLK,
PUC_PORT_4S, 0x18, 4, 0,
},
{ 0x131f, 0x2010, 0xffff, 0,
"SIIG Cyber I/O PCI 16C550 (20x family)",
DEFAULT_RCLK,
PUC_PORT_1S1P, 0x10, 4, 0,
},
{ 0x131f, 0x2011, 0xffff, 0,
"SIIG Cyber I/O PCI 16C650 (20x family)",
DEFAULT_RCLK,
PUC_PORT_1S1P, 0x10, 4, 0,
},
{ 0x131f, 0x2012, 0xffff, 0,
"SIIG Cyber I/O PCI 16C850 (20x family)",
DEFAULT_RCLK,
PUC_PORT_1S1P, 0x10, 4, 0,
},
{ 0x131f, 0x2021, 0xffff, 0,
"SIIG Cyber Parallel Dual PCI (20x family)",
0,
PUC_PORT_2P, 0x10, 8, 0,
},
{ 0x131f, 0x2030, 0xffff, 0,
"SIIG Cyber Serial Dual PCI 16C550 (20x family)",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x131f, 0x2031, 0xffff, 0,
"SIIG Cyber Serial Dual PCI 16C650 (20x family)",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x131f, 0x2032, 0xffff, 0,
"SIIG Cyber Serial Dual PCI 16C850 (20x family)",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x131f, 0x2040, 0xffff, 0,
"SIIG Cyber 2P1S PCI 16C550 (20x family)",
DEFAULT_RCLK,
PUC_PORT_1S2P, 0x10, -1, 0,
.config_function = puc_config_siig
},
{ 0x131f, 0x2041, 0xffff, 0,
"SIIG Cyber 2P1S PCI 16C650 (20x family)",
DEFAULT_RCLK,
PUC_PORT_1S2P, 0x10, -1, 0,
.config_function = puc_config_siig
},
{ 0x131f, 0x2042, 0xffff, 0,
"SIIG Cyber 2P1S PCI 16C850 (20x family)",
DEFAULT_RCLK,
PUC_PORT_1S2P, 0x10, -1, 0,
.config_function = puc_config_siig
},
{ 0x131f, 0x2050, 0xffff, 0,
"SIIG Cyber 4S PCI 16C550 (20x family)",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
},
{ 0x131f, 0x2051, 0xffff, 0,
"SIIG Cyber 4S PCI 16C650 (20x family)",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
},
{ 0x131f, 0x2052, 0xffff, 0,
"SIIG Cyber 4S PCI 16C850 (20x family)",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
},
{ 0x131f, 0x2060, 0xffff, 0,
"SIIG Cyber 2S1P PCI 16C550 (20x family)",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x10, 4, 0,
},
{ 0x131f, 0x2061, 0xffff, 0,
"SIIG Cyber 2S1P PCI 16C650 (20x family)",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x10, 4, 0,
},
{ 0x131f, 0x2062, 0xffff, 0,
"SIIG Cyber 2S1P PCI 16C850 (20x family)",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x10, 4, 0,
},
{ 0x131f, 0x2081, 0xffff, 0,
"SIIG PS8000 8S PCI 16C650 (20x family)",
DEFAULT_RCLK,
PUC_PORT_8S, 0x10, -1, -1,
.config_function = puc_config_siig
},
{ 0x135c, 0x0010, 0xffff, 0,
"Quatech QSC-100",
-3, /* max 8x clock rate */
PUC_PORT_4S, 0x14, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x0020, 0xffff, 0,
"Quatech DSC-100",
-1, /* max 2x clock rate */
PUC_PORT_2S, 0x14, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x0030, 0xffff, 0,
"Quatech DSC-200/300",
-1, /* max 2x clock rate */
PUC_PORT_2S, 0x14, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x0040, 0xffff, 0,
"Quatech QSC-200/300",
-3, /* max 8x clock rate */
PUC_PORT_4S, 0x14, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x0050, 0xffff, 0,
"Quatech ESC-100D",
-3, /* max 8x clock rate */
PUC_PORT_8S, 0x14, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x0060, 0xffff, 0,
"Quatech ESC-100M",
-3, /* max 8x clock rate */
PUC_PORT_8S, 0x14, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x0170, 0xffff, 0,
"Quatech QSCLP-100",
-1, /* max 2x clock rate */
PUC_PORT_4S, 0x18, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x0180, 0xffff, 0,
"Quatech DSCLP-100",
-1, /* max 3x clock rate */
PUC_PORT_2S, 0x18, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x01b0, 0xffff, 0,
"Quatech DSCLP-200/300",
-1, /* max 2x clock rate */
PUC_PORT_2S, 0x18, 0, 8,
.config_function = puc_config_quatech
},
{ 0x135c, 0x01e0, 0xffff, 0,
"Quatech ESCLP-100",
-3, /* max 8x clock rate */
PUC_PORT_8S, 0x10, 0, 8,
.config_function = puc_config_quatech
},
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
{ 0x1393, 0x1024, 0xffff, 0,
"Moxa Technologies, Smartio CP-102E/PCIe",
DEFAULT_RCLK * 8,
- Change back "d_ofs" to int8_t to not pessimize padding and size of "struct puc_cfg". - Use "puc_config_moxa" for Moxa boards that need d_ofs greater than 0x7f Prodded by: marcel@, gavin@ MFC after: 3 days
2012-07-31 05:23:23 +00:00
PUC_PORT_2S, 0x14, 0, -1,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
.config_function = puc_config_moxa
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
},
{ 0x1393, 0x1025, 0xffff, 0,
"Moxa Technologies, Smartio CP-102EL/PCIe",
DEFAULT_RCLK * 8,
- Change back "d_ofs" to int8_t to not pessimize padding and size of "struct puc_cfg". - Use "puc_config_moxa" for Moxa boards that need d_ofs greater than 0x7f Prodded by: marcel@, gavin@ MFC after: 3 days
2012-07-31 05:23:23 +00:00
PUC_PORT_2S, 0x14, 0, -1,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
.config_function = puc_config_moxa
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1393, 0x1040, 0xffff, 0,
"Moxa Technologies, Smartio C104H/PCI",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x18, 0, 8,
},
{ 0x1393, 0x1041, 0xffff, 0,
"Moxa Technologies, Smartio CP-104UL/PCI",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x18, 0, 8,
},
- add support for CP-104EL-A and CP-104JU to puc PR: 151365 Submitted by: Joerg Niendorf <f5d10a@internode.on.net> Approved by: jhb
2011-11-11 22:24:16 +00:00
{ 0x1393, 0x1042, 0xffff, 0,
"Moxa Technologies, Smartio CP-104JU/PCI",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x18, 0, 8,
},
o Add Moxa Technologies CP-104EL PCI Express 4 port Serial card. PR: kern/119515 Submitted by: Gavin Stone-Tolcher MFC after: 1 month
2008-01-12 19:14:29 +00:00
{ 0x1393, 0x1043, 0xffff, 0,
"Moxa Technologies, Smartio CP-104EL/PCIe",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x18, 0, 8,
},
- add support for CP-104EL-A and CP-104JU to puc PR: 151365 Submitted by: Joerg Niendorf <f5d10a@internode.on.net> Approved by: jhb
2011-11-11 22:24:16 +00:00
{ 0x1393, 0x1045, 0xffff, 0,
"Moxa Technologies, Smartio CP-104EL-A/PCIe",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x14, 0, -1,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
.config_function = puc_config_moxa
- add support for CP-104EL-A and CP-104JU to puc PR: 151365 Submitted by: Joerg Niendorf <f5d10a@internode.on.net> Approved by: jhb
2011-11-11 22:24:16 +00:00
},
Add device id for the Moxa CP-112UL dual-port serial adapters. Submitted by: Jan Mikkelsen janm of transactionware com Approved by: re (kib) MFC after: 1 week
2011-08-15 19:29:25 +00:00
{ 0x1393, 0x1120, 0xffff, 0,
"Moxa Technologies, CP-112UL",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x18, 0, 8,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1393, 0x1141, 0xffff, 0,
"Moxa Technologies, Industio CP-114",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x18, 0, 8,
},
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
{ 0x1393, 0x1144, 0xffff, 0,
"Moxa Technologies, Smartio CP-114EL/PCIe",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x14, 0, -1,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
.config_function = puc_config_moxa
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
},
{ 0x1393, 0x1182, 0xffff, 0,
"Moxa Technologies, Smartio CP-118EL-A/PCIe",
DEFAULT_RCLK * 8,
- Change back "d_ofs" to int8_t to not pessimize padding and size of "struct puc_cfg". - Use "puc_config_moxa" for Moxa boards that need d_ofs greater than 0x7f Prodded by: marcel@, gavin@ MFC after: 3 days
2012-07-31 05:23:23 +00:00
PUC_PORT_8S, 0x14, 0, -1,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
.config_function = puc_config_moxa
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1393, 0x1680, 0xffff, 0,
"Moxa Technologies, C168H/PCI",
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x18, 0, 8,
},
{ 0x1393, 0x1681, 0xffff, 0,
"Moxa Technologies, C168U/PCI",
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x18, 0, 8,
},
- Add support for Moxa Technologies CP-168EL/PCIe card. Submitted by: dmarck MFC after: 1 week
2009-01-27 09:38:44 +00:00
{ 0x1393, 0x1682, 0xffff, 0,
"Moxa Technologies, CP-168EL/PCIe",
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x18, 0, 8,
},
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
{ 0x1393, 0x1683, 0xffff, 0,
"Moxa Technologies, Smartio CP-168EL-A/PCIe",
DEFAULT_RCLK * 8,
- Change back "d_ofs" to int8_t to not pessimize padding and size of "struct puc_cfg". - Use "puc_config_moxa" for Moxa boards that need d_ofs greater than 0x7f Prodded by: marcel@, gavin@ MFC after: 3 days
2012-07-31 05:23:23 +00:00
PUC_PORT_8S, 0x14, 0, -1,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
.config_function = puc_config_moxa
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
},
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
{ 0x13a8, 0x0152, 0xffff, 0,
"Exar XR17C/D152",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, -1,
.config_function = puc_config_exar
},
{ 0x13a8, 0x0154, 0xffff, 0,
"Exar XR17C154",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, -1,
.config_function = puc_config_exar
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x13a8, 0x0158, 0xffff, 0,
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
"Exar XR17C158",
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x10, 0, -1,
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
.config_function = puc_config_exar
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
},
Add Exar octal PCI UART. Submitted by: Mark Johnston Obtained from: Sandvine Incorporated
2010-12-18 02:54:51 +00:00
{ 0x13a8, 0x0258, 0xffff, 0,
"Exar XR17V258IV",
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x10, 0, -1,
Correct the definition for Exar XR17V258IV: we must use a config_function to specify the offset into the PCI memory spare at which each serial port will find its registers. This was already done for other Exar PCI serial devices; it was accidentally omitted for this specific device. Sponsored by: Sandvine Incorporated MFC after: 1 week
2013-03-18 19:22:51 +00:00
.config_function = puc_config_exar
Add Exar octal PCI UART. Submitted by: Mark Johnston Obtained from: Sandvine Incorporated
2010-12-18 02:54:51 +00:00
},
Add support for Exar XR17V358 8-port serial device to puc(4) Reviewed by: marius Sponsored by: Sandvine Inc. MFC after: 1 week
2013-03-15 19:58:44 +00:00
/* The XR17V358 uses the 125MHz PCIe clock as its reference clock. */
{ 0x13a8, 0x0358, 0xffff, 0,
"Exar XR17V358",
125000000,
PUC_PORT_8S, 0x10, 0, -1,
.config_function = puc_config_exar_pcie
},
Add support for Advantech PCI-1602 RS-485/RS-422 serial card PR: kern/169726 Submitted by: Jan Mikkelsen <janm@transactionware.com> Approved by: cperciva (implicit) MFC after: 5 days
2012-11-09 01:51:06 +00:00
{ 0x13fe, 0x1600, 0x1602, 0x0002,
"Advantech PCI-1602",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, 8,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1407, 0x0100, 0xffff, 0,
"Lava Computers Dual Serial",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x1407, 0x0101, 0xffff, 0,
"Lava Computers Quatro A",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x1407, 0x0102, 0xffff, 0,
"Lava Computers Quatro B",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x1407, 0x0120, 0xffff, 0,
"Lava Computers Quattro-PCI A",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x1407, 0x0121, 0xffff, 0,
"Lava Computers Quattro-PCI B",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x1407, 0x0180, 0xffff, 0,
"Lava Computers Octo A",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
},
{ 0x1407, 0x0181, 0xffff, 0,
"Lava Computers Octo B",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
},
Add support for the Sunix SUN1889-based dual parallel port card. PR: kern/128219 Submitted by: Thinker K.F. Li <thinker at branda dot to>
2009-02-12 10:39:19 +00:00
{ 0x1409, 0x7268, 0xffff, 0,
"Sunix SUN1888",
0,
PUC_PORT_2P, 0x10, 0, 8,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1409, 0x7168, 0xffff, 0,
NULL,
DEFAULT_RCLK * 8,
PUC_PORT_NONSTANDARD, 0x10, -1, -1,
.config_function = puc_config_timedia
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
},
/*
* Boards with an Oxford Semiconductor chip.
*
* Oxford Semiconductor provides documentation for their chip at:
Add support for Oxford PCI Express Expresso family devices. For these devices, the number of supported ports is read from a register in BAR 0. PR: kern/134878 Submitted by: David Wood david of wood2 org uk MFC after: 1 week
2011-04-28 19:19:25 +00:00
* <URL:http://www.plxtech.com/products/uart/>
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
*
* As sold by Kouwell <URL:http://www.kouwell.com/>.
* I/O Flex PCI I/O Card Model-223 with 4 serial and 1 parallel ports.
*/
- add support for I-O DATA RSA-PCI2/R PR: kern/142999 Submitted by: Takefu Kenji <takefu@airport.fm> Approved by: jhb Approved by: sahil (mentor) MFC after: 1 week
2011-10-15 21:06:08 +00:00
{
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
0x1415, 0x9501, 0x10fc, 0xc070,
"I-O DATA RSA-PCI2/R",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, 8,
- add support for I-O DATA RSA-PCI2/R PR: kern/142999 Submitted by: Takefu Kenji <takefu@airport.fm> Approved by: jhb Approved by: sahil (mentor) MFC after: 1 week
2011-10-15 21:06:08 +00:00
},
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
Add an entry for the "SIIG Cyber 4 PCI 16550", which is a four-port card based on the OX16PCI954 chip with a non-standard clock. MFC after: 3 days
2008-10-25 10:55:49 +00:00
{ 0x1415, 0x9501, 0x131f, 0x2050,
"SIIG Cyber 4 PCI 16550",
DEFAULT_RCLK * 10,
PUC_PORT_4S, 0x10, 0, 8,
},
Add SIIG 4 port serial card based on the Oxford OX16PCI954.
2006-09-04 18:27:14 +00:00
{ 0x1415, 0x9501, 0x131f, 0x2051,
"SIIG Cyber 4S PCI 16C650 (20x family)",
DEFAULT_RCLK * 10,
PUC_PORT_4S, 0x10, 0, 8,
},
Add an entry for the SIIG Quartet Serial 850 which uses an Oxford chip with a non-default clock. PR: kern/147583 MFC after: 1 week
2011-05-10 12:40:35 +00:00
{ 0x1415, 0x9501, 0x131f, 0x2052,
"SIIG Quartet Serial 850",
DEFAULT_RCLK * 10,
PUC_PORT_4S, 0x10, 0, 8,
},
Add an entry for the Kuroutoshikou SERIAL4P-LPPCI2 which uses an Oxford 4 port chip but with a nonstandard clock. PR: kern/104212 Submitted by: Shuichi KITAGUCHI kit of ysnb net MFC after: 1 week
2011-05-02 14:34:03 +00:00
{ 0x1415, 0x9501, 0x14db, 0x2150,
"Kuroutoshikou SERIAL4P-LPPCI2",
DEFAULT_RCLK * 10,
PUC_PORT_4S, 0x10, 0, 8,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1415, 0x9501, 0xffff, 0,
Revert r179409; it breaks all OX16PCI954-based cards except the SIIG 4. MFC after: 3 days
2008-10-13 12:28:33 +00:00
"Oxford Semiconductor OX16PCI954 UARTs",
All of Oxford/PLX OX16PCI954, OXm16PCI954 and OXu16PCI954 share the exact same (subsystem) device and vendor IDs. However, the reference design for the OXu16PCI954 uses a 14.7456 MHz clock (as does the EXSYS EX-41098-2 equipped with these), while at least the OX16PCI954 defaults to a 1.8432 MHz one. According to the datasheets of these chips, the only difference in PCI configuration space is that OXu16PCI954 have a revision ID of 1 while the other two are at 0. So employ the latter for determining the default clock rates of this family. Note that one might think that the actual clock could be derived from the Clock Prescaler Register (CPR) of these chips. Unfortunately, this is not that case and its use and content are orthogonal to the frequency of the crystal employed. Tested with an EXSYS EX-41098-2, which identifies and attaches as: pcib4@pci0:19:0:0: class=0x060400 card=0x02dd1014 chip=0x10801b21 rev=0x03 hdr=0x01 vendor = 'ASMedia Technology Inc.' device = 'ASM1083/1085 PCIe to PCI Bridge' class = bridge subclass = PCI-PCI puc0@pci0:20:4:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc1@pci0:20:4:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge puc2@pci0:20:8:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc3@pci0:20:8:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge pci20: <ACPI PCI bus> on pcib4 puc0: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5000-0x501f, 0x5020-0x503f mem 0xc6000000-0xc6000fff,0xc6001000-0xc6001fff irq 16 at device 4.0 on pci20 uart1: <16950 or compatible> at port 1 on puc0 uart2: <16950 or compatible> at port 2 on puc0 uart3: <16950 or compatible> at port 3 on puc0 uart4: <16950 or compatible> at port 4 on puc0 puc1: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x5040-0x505f,0x5060-0x507f mem 0xc6002000-0xc6002fff,0xc6003000-0xc6003fff irq 16 at device 4.1 on pci20 puc2: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5080-0x509f, 0x50a0-0x50bf mem 0xc6004000-0xc6004fff,0xc6005000-0xc6005fff irq 16 at device 8.0 on pci20 uart5: <16950 or compatible> at port 1 on puc2 uart6: <16950 or compatible> at port 2 on puc2 uart7: <16950 or compatible> at port 3 on puc2 uart8: <16950 or compatible> at port 4 on puc2 puc3: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x50c0-0x50df,0x50e0-0x50ff mem 0xc6006000-0xc6006fff,0xc6007000-0xc6007fff irq 16 at device 8.1 on pci20 MFC after: 2 weeks
2013-06-13 22:13:41 +00:00
0,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
PUC_PORT_4S, 0x10, 0, 8,
All of Oxford/PLX OX16PCI954, OXm16PCI954 and OXu16PCI954 share the exact same (subsystem) device and vendor IDs. However, the reference design for the OXu16PCI954 uses a 14.7456 MHz clock (as does the EXSYS EX-41098-2 equipped with these), while at least the OX16PCI954 defaults to a 1.8432 MHz one. According to the datasheets of these chips, the only difference in PCI configuration space is that OXu16PCI954 have a revision ID of 1 while the other two are at 0. So employ the latter for determining the default clock rates of this family. Note that one might think that the actual clock could be derived from the Clock Prescaler Register (CPR) of these chips. Unfortunately, this is not that case and its use and content are orthogonal to the frequency of the crystal employed. Tested with an EXSYS EX-41098-2, which identifies and attaches as: pcib4@pci0:19:0:0: class=0x060400 card=0x02dd1014 chip=0x10801b21 rev=0x03 hdr=0x01 vendor = 'ASMedia Technology Inc.' device = 'ASM1083/1085 PCIe to PCI Bridge' class = bridge subclass = PCI-PCI puc0@pci0:20:4:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc1@pci0:20:4:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge puc2@pci0:20:8:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc3@pci0:20:8:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge pci20: <ACPI PCI bus> on pcib4 puc0: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5000-0x501f, 0x5020-0x503f mem 0xc6000000-0xc6000fff,0xc6001000-0xc6001fff irq 16 at device 4.0 on pci20 uart1: <16950 or compatible> at port 1 on puc0 uart2: <16950 or compatible> at port 2 on puc0 uart3: <16950 or compatible> at port 3 on puc0 uart4: <16950 or compatible> at port 4 on puc0 puc1: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x5040-0x505f,0x5060-0x507f mem 0xc6002000-0xc6002fff,0xc6003000-0xc6003fff irq 16 at device 4.1 on pci20 puc2: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5080-0x509f, 0x50a0-0x50bf mem 0xc6004000-0xc6004fff,0xc6005000-0xc6005fff irq 16 at device 8.0 on pci20 uart5: <16950 or compatible> at port 1 on puc2 uart6: <16950 or compatible> at port 2 on puc2 uart7: <16950 or compatible> at port 3 on puc2 uart8: <16950 or compatible> at port 4 on puc2 puc3: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x50c0-0x50df,0x50e0-0x50ff mem 0xc6006000-0xc6006fff,0xc6007000-0xc6007fff irq 16 at device 8.1 on pci20 MFC after: 2 weeks
2013-06-13 22:13:41 +00:00
.config_function = puc_config_oxford_pci954
Add in a missing device entry that I thought was already in there. This is from the same PR. Prompted by the reporter of the PR. PR: 38372
2003-08-21 03:54:20 +00:00
},
Add support for the SIIG Cyber 2S PCIe adapter. It is based on an Oxford Semiconductor OX16PCI954 but uses only two ports with a non-default clock rate. PR: kern/152034 Tested by: Hans Fiedler hans of hermes louisville edu MFC after: 1 week
2011-05-19 11:41:12 +00:00
{ 0x1415, 0x950a, 0x131f, 0x2030,
"SIIG Cyber 2S PCIe",
DEFAULT_RCLK * 10,
PUC_PORT_2S, 0x10, 0, 8,
},
Add support for SIIG Cyber Serial Dual PCI 16C850 Submitted by: David Boyd David.Boyd@insightbb.com Approved by: cperciva MFC after: 3 days
2012-08-05 19:37:18 +00:00
{ 0x1415, 0x950a, 0x131f, 0x2032,
"SIIG Cyber Serial Dual PCI 16C850",
DEFAULT_RCLK * 10,
PUC_PORT_4S, 0x10, 0, 8,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1415, 0x950a, 0xffff, 0,
Revert r179409; it breaks all OX16PCI954-based cards except the SIIG 4. MFC after: 3 days
2008-10-13 12:28:33 +00:00
"Oxford Semiconductor OX16PCI954 UARTs",
DEFAULT_RCLK,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
PUC_PORT_4S, 0x10, 0, 8,
},
add support for NetMos NM9805 1284 Printer port Submitted by: Willy Offermans <W.K.Offermans@TUe.nl> MFC after: 2 weeks
2005-02-09 18:38:28 +00:00
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1415, 0x9511, 0xffff, 0,
"Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x1415, 0x9521, 0xffff, 0,
"Oxford Semiconductor OX16PCI952 UARTs",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
Add support for the Oxford OX16PCI958-based card. Note, that the patch provided with this card for the Linux states that the card uses DEFAULT_RCLK * 2, while in fact it is '* 10'. So probably we should also use the subdevice/subvendord here. For now just ignore that fact. PR: kern/129665 Submitted by: bsam Obtained from: united efforst with bsam
2008-12-27 15:22:22 +00:00
{ 0x1415, 0x9538, 0xffff, 0,
"Oxford Semiconductor OX16PCI958 UARTs",
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
DEFAULT_RCLK,
Add support for the Oxford OX16PCI958-based card. Note, that the patch provided with this card for the Linux states that the card uses DEFAULT_RCLK * 2, while in fact it is '* 10'. So probably we should also use the subdevice/subvendord here. For now just ignore that fact. PR: kern/129665 Submitted by: bsam Obtained from: united efforst with bsam
2008-12-27 15:22:22 +00:00
PUC_PORT_8S, 0x18, 0, 8,
},
Add support for the Perle Speed4 LE. Submitted by: Douglas K. Rand rand of meridian-enviro com MFC after: 3 days
2010-05-20 13:16:42 +00:00
/*
* Perle boards use Oxford Semiconductor chips, but they store the
* Oxford Semiconductor device ID as a subvendor device ID and use
* their own device IDs.
*/
{ 0x155f, 0x0331, 0xffff, 0,
Add additional Perle Speed LE serial cards PR: kern/168816 Submitted by: Dennis Oyama <doyama@perle.com> Approved by: cperciva MFC after: 1 week
2012-08-05 08:10:02 +00:00
"Perle Ultraport4 Express",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x155f, 0xB012, 0xffff, 0,
"Perle Speed2 LE",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, 8,
},
{ 0x155f, 0xB022, 0xffff, 0,
"Perle Speed2 LE",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, 8,
},
{ 0x155f, 0xB004, 0xffff, 0,
Add support for the Perle Speed4 LE. Submitted by: Douglas K. Rand rand of meridian-enviro com MFC after: 3 days
2010-05-20 13:16:42 +00:00
"Perle Speed4 LE",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, 8,
},
Add additional Perle Speed LE serial cards PR: kern/168816 Submitted by: Dennis Oyama <doyama@perle.com> Approved by: cperciva MFC after: 1 week
2012-08-05 08:10:02 +00:00
{ 0x155f, 0xB008, 0xffff, 0,
"Perle Speed8 LE",
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x10, 0, 8,
},
Add support for Oxford PCI Express Expresso family devices. For these devices, the number of supported ports is read from a register in BAR 0. PR: kern/134878 Submitted by: David Wood david of wood2 org uk MFC after: 1 week
2011-04-28 19:19:25 +00:00
/*
* Oxford Semiconductor PCI Express Expresso family
*
* Found in many 'native' PCI Express serial boards such as:
*
* eMegatech MP954ER4 (4 port) and MP958ER8 (8 port)
* <URL:http://www.emegatech.com.tw/pdrs232pcie.html>
*
* Lindy 51189 (4 port)
* <URL:http://www.lindy.com> <URL:http://tinyurl.com/lindy-51189>
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
*
Add support for Oxford PCI Express Expresso family devices. For these devices, the number of supported ports is read from a register in BAR 0. PR: kern/134878 Submitted by: David Wood david of wood2 org uk MFC after: 1 week
2011-04-28 19:19:25 +00:00
* StarTech.com PEX4S952 (4 port) and PEX8S952 (8 port)
* <URL:http://www.startech.com>
*/
Add Oxford Semiconductor OXPCIe952 (0x1c38) 1 port serial card. PR: kern/160895 Submitted by: Konstantin V. Krotov MFC after: 1 week
2011-09-29 15:43:02 +00:00
{ 0x1415, 0xc138, 0xffff, 0,
"Oxford Semiconductor OXPCIe952 UARTs",
DEFAULT_RCLK * 0x22,
PUC_PORT_NONSTANDARD, 0x10, 0, -1,
.config_function = puc_config_oxford_pcie
},
Add support for Oxford PCI Express Expresso family devices. For these devices, the number of supported ports is read from a register in BAR 0. PR: kern/134878 Submitted by: David Wood david of wood2 org uk MFC after: 1 week
2011-04-28 19:19:25 +00:00
{ 0x1415, 0xc158, 0xffff, 0,
"Oxford Semiconductor OXPCIe952 UARTs",
DEFAULT_RCLK * 0x22,
PUC_PORT_NONSTANDARD, 0x10, 0, -1,
.config_function = puc_config_oxford_pcie
},
{ 0x1415, 0xc15d, 0xffff, 0,
"Oxford Semiconductor OXPCIe952 UARTs (function 1)",
DEFAULT_RCLK * 0x22,
PUC_PORT_NONSTANDARD, 0x10, 0, -1,
.config_function = puc_config_oxford_pcie
},
{ 0x1415, 0xc208, 0xffff, 0,
"Oxford Semiconductor OXPCIe954 UARTs",
DEFAULT_RCLK * 0x22,
PUC_PORT_NONSTANDARD, 0x10, 0, -1,
.config_function = puc_config_oxford_pcie
},
{ 0x1415, 0xc20d, 0xffff, 0,
"Oxford Semiconductor OXPCIe954 UARTs (function 1)",
DEFAULT_RCLK * 0x22,
PUC_PORT_NONSTANDARD, 0x10, 0, -1,
.config_function = puc_config_oxford_pcie
},
{ 0x1415, 0xc308, 0xffff, 0,
"Oxford Semiconductor OXPCIe958 UARTs",
DEFAULT_RCLK * 0x22,
PUC_PORT_NONSTANDARD, 0x10, 0, -1,
.config_function = puc_config_oxford_pcie
},
{ 0x1415, 0xc30d, 0xffff, 0,
"Oxford Semiconductor OXPCIe958 UARTs (function 1)",
DEFAULT_RCLK * 0x22,
PUC_PORT_NONSTANDARD, 0x10, 0, -1,
.config_function = puc_config_oxford_pcie
},
Add the VScom PCI-100L card. PR: kern/72352 Submitted by: Thomas Nystrom
2008-08-22 00:12:08 +00:00
{ 0x14d2, 0x8010, 0xffff, 0,
"VScom PCI-100L",
DEFAULT_RCLK * 8,
PUC_PORT_1S, 0x14, 0, 0,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x14d2, 0x8020, 0xffff, 0,
"VScom PCI-200L",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x14, 4, 0,
},
{ 0x14d2, 0x8028, 0xffff, 0,
"VScom 200Li",
DEFAULT_RCLK,
PUC_PORT_2S, 0x20, 0, 8,
Add description of Cronyx Omega2-PCI (8x port serial adapter).
2004-05-17 12:57:30 +00:00
},
Add support for Chase/Perle PCI FAST-4 4 port serial cards which appear to be the same as Boca Research Turbo Serial 654 (4 serial port). While add the 8 port variants as well. Submitted by: sten@blinkenlights.nl PR: kern/75793 MFC after: 1 week
2005-01-05 20:06:04 +00:00
/*
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
* VScom (Titan?) PCI-800L. More modern variant of the
* PCI-800. Uses 6 discrete 16550 UARTs, plus another
* two of them obviously implemented as macro cells in
* the ASIC. This causes the weird port access pattern
* below, where two of the IO port ranges each access
* one of the ASIC UARTs, and a block of IO addresses
* access the external UARTs.
Add support for Chase/Perle PCI FAST-4 4 port serial cards which appear to be the same as Boca Research Turbo Serial 654 (4 serial port). While add the 8 port variants as well. Submitted by: sten@blinkenlights.nl PR: kern/75793 MFC after: 1 week
2005-01-05 20:06:04 +00:00
*/
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x14d2, 0x8080, 0xffff, 0,
"Titan VScom PCI-800L",
DEFAULT_RCLK * 8,
PUC_PORT_8S, 0x14, -1, -1,
.config_function = puc_config_titan
Add support for Chase/Perle PCI FAST-4 4 port serial cards which appear to be the same as Boca Research Turbo Serial 654 (4 serial port). While add the 8 port variants as well. Submitted by: sten@blinkenlights.nl PR: kern/75793 MFC after: 1 week
2005-01-05 20:06:04 +00:00
},
/*
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
* VScom PCI-800H. Uses 8 16950 UART, behind a PCI chips that offers
* 4 com port on PCI device 0 and 4 on PCI device 1. PCI device 0 has
* device ID 3 and PCI device 1 device ID 4.
Add support for Chase/Perle PCI FAST-4 4 port serial cards which appear to be the same as Boca Research Turbo Serial 654 (4 serial port). While add the 8 port variants as well. Submitted by: sten@blinkenlights.nl PR: kern/75793 MFC after: 1 week
2005-01-05 20:06:04 +00:00
*/
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x14d2, 0xa003, 0xffff, 0,
"Titan PCI-800H",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, 8,
},
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x14d2, 0xa004, 0xffff, 0,
"Titan PCI-800H",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x14d2, 0xa005, 0xffff, 0,
"Titan PCI-200H",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, 8,
},
{ 0x14d2, 0xe020, 0xffff, 0,
"Titan VScom PCI-200HV2",
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 4, 0,
},
- add support for Titan VScom PCIex-800H PR: kern/124128 Submitted by: Maxim Frolov <maxim.frolov.07@gmail.com> (original) Approved by: jhb MFC after: 1 week
2011-11-15 17:53:29 +00:00
{ 0x14d2, 0xa007, 0xffff, 0,
"Titan VScom PCIex-800H",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x14d2, 0xa008, 0xffff, 0,
"Titan VScom PCIex-800H",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, 8,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x14db, 0x2130, 0xffff, 0,
"Avlab Technology, PCI IO 2S",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x14db, 0x2150, 0xffff, 0,
"Avlab Low Profile PCI 4 Serial",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
Add yet another entry to the list.
2005-11-05 21:04:26 +00:00
},
Add PCI ID for Dell RAC IV/ERA Virtual UART (PowerEdge 1850). Trim name of existing Dell RAC devices. Trim comments. With help from: dpk at dpk dot net MFC after: 1 week
2005-01-27 01:17:32 +00:00
Add the Avlab Technology PCI IO 4S-850 4 port serial card. PR: kern/110797 Submitted by: Trevor Roydhouse
2008-08-21 23:22:32 +00:00
{ 0x14db, 0x2152, 0xffff, 0,
"Avlab Low Profile PCI 4 Serial",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x1592, 0x0781, 0xffff, 0,
"Syba Tech Ltd. PCI-4S2P-550-ECP",
DEFAULT_RCLK,
PUC_PORT_4S1P, 0x10, 0, -1,
.config_function = puc_config_syba
},
Distinguish between the different variants and configurations of Sunix {MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S. Among others, this fixes the hang seen when trying to probe the none- existent second UART on an actually 1-port chip. Obtained from: NetBSD (BAR layouts) MFC after: 3 days Sponsored by: Bally Wulff Games & Entertainment GmbH
2014-04-08 07:32:32 +00:00
{ 0x1fd4, 0x1999, 0x1fd4, 0x0002,
"Sunix SER5xxxx 2-port serial",
Add support for the Sunix SER5437A dual serial PCI Express card.
2012-06-08 06:07:23 +00:00
DEFAULT_RCLK * 8,
PUC_PORT_2S, 0x10, 0, 8,
},
Distinguish between the different variants and configurations of Sunix {MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S. Among others, this fixes the hang seen when trying to probe the none- existent second UART on an actually 1-port chip. Obtained from: NetBSD (BAR layouts) MFC after: 3 days Sponsored by: Bally Wulff Games & Entertainment GmbH
2014-04-08 07:32:32 +00:00
{ 0x1fd4, 0x1999, 0x1fd4, 0x0004,
"Sunix SER5xxxx 4-port serial",
DEFAULT_RCLK * 8,
PUC_PORT_4S, 0x10, 0, 8,
},
{ 0x1fd4, 0x1999, 0x1fd4, 0x0008,
"Sunix SER5xxxx 8-port serial",
DEFAULT_RCLK * 8,
PUC_PORT_8S, -1, -1, -1,
.config_function = puc_config_sunix
},
{ 0x1fd4, 0x1999, 0x1fd4, 0x0101,
"Sunix MIO5xxxx 1-port serial and 1284 Printer port",
DEFAULT_RCLK * 8,
PUC_PORT_1S1P, -1, -1, -1,
.config_function = puc_config_sunix
},
{ 0x1fd4, 0x1999, 0x1fd4, 0x0102,
Correct a typo in a device description added in r264257.
2014-04-15 19:58:05 +00:00
"Sunix MIO5xxxx 2-port serial and 1284 Printer port",
Distinguish between the different variants and configurations of Sunix {MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S. Among others, this fixes the hang seen when trying to probe the none- existent second UART on an actually 1-port chip. Obtained from: NetBSD (BAR layouts) MFC after: 3 days Sponsored by: Bally Wulff Games & Entertainment GmbH
2014-04-08 07:32:32 +00:00
DEFAULT_RCLK * 8,
PUC_PORT_2S1P, -1, -1, -1,
.config_function = puc_config_sunix
},
{ 0x1fd4, 0x1999, 0x1fd4, 0x0104,
"Sunix MIO5xxxx 4-port serial and 1284 Printer port",
DEFAULT_RCLK * 8,
PUC_PORT_4S1P, -1, -1, -1,
.config_function = puc_config_sunix
},
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
{ 0x5372, 0x6873, 0xffff, 0,
"Sun 1040 PCI Quad Serial",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 4, 0,
Add support for Sun 1040 PCI Quad Serial PR: kern/163450 Submitted by: Anonymous Hardware Hacker <silicium@harmony-p.ath.cx> Approved by: cperciva MFC after: 1 week
2012-05-30 03:47:51 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x6666, 0x0001, 0xffff, 0,
"Decision Computer Inc, PCCOM 4-port serial",
DEFAULT_RCLK,
PUC_PORT_4S, 0x1c, 0, 8,
},
Add the Decision Computer Inc, PCCOM 8-port serial card. PR: kern/69730 Submitted by: Darrin Smith
2008-08-22 00:13:17 +00:00
{ 0x6666, 0x0002, 0xffff, 0,
"Decision Computer Inc, PCCOM 8-port serial",
DEFAULT_RCLK,
PUC_PORT_8S, 0x1c, 0, 8,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x6666, 0x0004, 0xffff, 0,
"PCCOM dual port RS232/422/485",
DEFAULT_RCLK,
PUC_PORT_2S, 0x1c, 0, 8,
},
{ 0x9710, 0x9815, 0xffff, 0,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
"NetMos NM9815 Dual 1284 Printer port",
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
0,
PUC_PORT_2P, 0x10, 8, 0,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
Add support for the single-port NetMos NM9835 serial adapter. The puc(4) entry is a specific entry to override the generic NetMos entry so that puc(4) will leave this device alone and let uart(4) claim it. Submitted by: Navdeep Parhar nparhar @ gmail Reviewed by: marcel MFC after: 1 week
2009-03-05 16:43:33 +00:00
/*
Distinguish between the different variants and configurations of Sunix {MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S. Among others, this fixes the hang seen when trying to probe the none- existent second UART on an actually 1-port chip. Obtained from: NetBSD (BAR layouts) MFC after: 3 days Sponsored by: Bally Wulff Games & Entertainment GmbH
2014-04-08 07:32:32 +00:00
* This is more specific than the generic NM9835 entry, and is placed
* here to _prevent_ puc(4) from claiming this single port card.
Add support for the single-port NetMos NM9835 serial adapter. The puc(4) entry is a specific entry to override the generic NetMos entry so that puc(4) will leave this device alone and let uart(4) claim it. Submitted by: Navdeep Parhar nparhar @ gmail Reviewed by: marcel MFC after: 1 week
2009-03-05 16:43:33 +00:00
*
* uart(4) will claim this device.
*/
{ 0x9710, 0x9835, 0x1000, 1,
"NetMos NM9835 based 1-port serial",
DEFAULT_RCLK,
PUC_PORT_1S, 0x10, 4, 0,
},
Make puc(4) aware of this 2 port serial card based on NetMos 9835: puc0@pci0:4:1:0: class=0x070002 card=0x00021000 chip=0x98359710 rev=0x01 hdr=0x00 Reviewed by: marcel@ Approved by: gnn (mentor)
2009-06-20 00:04:48 +00:00
{ 0x9710, 0x9835, 0x1000, 2,
"NetMos NM9835 based 2-port serial",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0x9710, 0x9835, 0xffff, 0,
"NetMos NM9835 Dual UART and 1284 Printer port",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x10, 4, 0,
},
{ 0x9710, 0x9845, 0x1000, 0x0006,
"NetMos NM9845 6 Port UART",
DEFAULT_RCLK,
PUC_PORT_6S, 0x10, 4, 0,
},
{ 0x9710, 0x9845, 0xffff, 0,
"NetMos NM9845 Quad UART and 1284 Printer port",
DEFAULT_RCLK,
PUC_PORT_4S1P, 0x10, 4, 0,
},
Add support for the NetMos NM9865 family of Serial/Parallel ports. Obtained from: NetMos MCS9865 v1.0.0.1 driver MFC after: 3 days
2009-12-07 20:05:02 +00:00
{ 0x9710, 0x9865, 0xa000, 0x3002,
"NetMos NM9865 Dual UART",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 4, 0,
},
{ 0x9710, 0x9865, 0xa000, 0x3003,
"NetMos NM9865 Triple UART",
DEFAULT_RCLK,
PUC_PORT_3S, 0x10, 4, 0,
},
{ 0x9710, 0x9865, 0xa000, 0x3004,
"NetMos NM9865 Quad UART",
DEFAULT_RCLK,
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
PUC_PORT_4S, 0x10, 4, 0,
Add support for the NetMos NM9865 family of Serial/Parallel ports. Obtained from: NetMos MCS9865 v1.0.0.1 driver MFC after: 3 days
2009-12-07 20:05:02 +00:00
},
{ 0x9710, 0x9865, 0xa000, 0x3011,
"NetMos NM9865 Single UART and 1284 Printer port",
DEFAULT_RCLK,
PUC_PORT_1S1P, 0x10, 4, 0,
},
{ 0x9710, 0x9865, 0xa000, 0x3012,
"NetMos NM9865 Dual UART and 1284 Printer port",
DEFAULT_RCLK,
PUC_PORT_2S1P, 0x10, 4, 0,
},
{ 0x9710, 0x9865, 0xa000, 0x3020,
"NetMos NM9865 Dual 1284 Printer port",
DEFAULT_RCLK,
PUC_PORT_2P, 0x10, 4, 0,
},
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
{ 0xb00c, 0x021c, 0xffff, 0,
"IC Book Labs Gunboat x4 Lite",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 0, 8,
.config_function = puc_config_icbook
},
{ 0xb00c, 0x031c, 0xffff, 0,
"IC Book Labs Gunboat x4 Pro",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 0, 8,
.config_function = puc_config_icbook
},
{ 0xb00c, 0x041c, 0xffff, 0,
"IC Book Labs Ironclad x8 Lite",
DEFAULT_RCLK,
PUC_PORT_8S, 0x10, 0, 8,
.config_function = puc_config_icbook
},
{ 0xb00c, 0x051c, 0xffff, 0,
"IC Book Labs Ironclad x8 Pro",
DEFAULT_RCLK,
PUC_PORT_8S, 0x10, 0, 8,
.config_function = puc_config_icbook
},
{ 0xb00c, 0x081c, 0xffff, 0,
"IC Book Labs Dreadnought x16 Pro",
DEFAULT_RCLK * 8,
PUC_PORT_16S, 0x10, 0, 8,
.config_function = puc_config_icbook
},
{ 0xb00c, 0x091c, 0xffff, 0,
"IC Book Labs Dreadnought x16 Lite",
DEFAULT_RCLK,
PUC_PORT_16S, 0x10, 0, 8,
.config_function = puc_config_icbook
},
{ 0xb00c, 0x0a1c, 0xffff, 0,
"IC Book Labs Gunboat x2 Low Profile",
DEFAULT_RCLK,
PUC_PORT_2S, 0x10, 0, 8,
},
{ 0xb00c, 0x0b1c, 0xffff, 0,
"IC Book Labs Gunboat x4 Low Profile",
DEFAULT_RCLK,
PUC_PORT_4S, 0x10, 0, 8,
.config_function = puc_config_icbook
},
{ 0xffff, 0, 0xffff, 0, NULL, 0 }
Add the puc (PCI "Universal" Communications) driver. The idea and some of the structure definitions come from NetBSD to make it easier to share card definitions. The driver only acts as a shim between the pci bus and the sio driver. Later pci parallel ports could also be supported through this driver. Support for most single and multiport pci serial cards should be as simple as adding its definition to pucdata.c Tested with the following pci cards: Moxa Industio CP-114, 4 port RS-232,RS-422/485 Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports Netmos NM9835 PCI-2S-550, 2 port RS-232
2002-02-16 15:12:14 +00:00
};
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static int
puc_config_amc(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
switch (cmd) {
case PUC_CFG_GET_OFS:
*res = 8 * (port & 1);
return (0);
case PUC_CFG_GET_RID:
*res = 0x14 + (port >> 1) * 4;
return (0);
default:
break;
}
return (ENXIO);
}
static int
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
puc_config_diva(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
intptr_t *res)
{
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
const struct puc_cfg *cfg = sc->sc_cfg;
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
if (cmd == PUC_CFG_GET_OFS) {
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
if (cfg->subdevice == 0x1282) /* Everest SP */
port <<= 1;
else if (cfg->subdevice == 0x104b) /* Maestro SP2 */
port = (port == 3) ? 4 : port;
*res = port * 8 + ((port > 2) ? 0x18 : 0);
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
return (0);
}
return (ENXIO);
}
static int
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
puc_config_exar(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
intptr_t *res)
{
if (cmd == PUC_CFG_GET_OFS) {
- Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the real owner of the device ID. Also rename the associated config function while here. - Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152 and Exar XR17C154. Tested by: Mike Tancsa, Willy Offermans Willy of offermans rompen nl MFC after: 1 week
2011-06-03 20:59:21 +00:00
*res = port * 0x200;
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
return (0);
}
return (ENXIO);
}
Add support for Exar XR17V358 8-port serial device to puc(4) Reviewed by: marius Sponsored by: Sandvine Inc. MFC after: 1 week
2013-03-15 19:58:44 +00:00
static int
puc_config_exar_pcie(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
if (cmd == PUC_CFG_GET_OFS) {
*res = port * 0x400;
return (0);
}
return (ENXIO);
}
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static int
puc_config_icbook(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
if (cmd == PUC_CFG_GET_ILR) {
*res = PUC_ILR_DIGI;
return (0);
}
return (ENXIO);
}
- add support for CP-104EL-A and CP-104JU to puc PR: 151365 Submitted by: Joerg Niendorf <f5d10a@internode.on.net> Approved by: jhb
2011-11-11 22:24:16 +00:00
static int
puc_config_moxa(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
Add support for the following Moxa PCIe multiport serial boards: - CP102E - CP102EL - CP132EL - CP114EL - CP118EL-A - CP168EL-A MFC after: 1 week
2012-06-21 03:10:48 +00:00
if (cmd == PUC_CFG_GET_OFS) {
- Change back "d_ofs" to int8_t to not pessimize padding and size of "struct puc_cfg". - Use "puc_config_moxa" for Moxa boards that need d_ofs greater than 0x7f Prodded by: marcel@, gavin@ MFC after: 3 days
2012-07-31 05:23:23 +00:00
const struct puc_cfg *cfg = sc->sc_cfg;
if (port == 3 && (cfg->device == 0x1045 || cfg->device == 0x1144))
port = 7;
*res = port * 0x200;
- add support for CP-104EL-A and CP-104JU to puc PR: 151365 Submitted by: Joerg Niendorf <f5d10a@internode.on.net> Approved by: jhb
2011-11-11 22:24:16 +00:00
return 0;
}
return (ENXIO);
}
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static int
puc_config_quatech(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
const struct puc_cfg *cfg = sc->sc_cfg;
struct puc_bar *bar;
uint8_t v0, v1;
switch (cmd) {
case PUC_CFG_SETUP:
/*
* Check if the scratchpad register is enabled or if the
* interrupt status and options registers are active.
*/
bar = puc_get_bar(sc, cfg->rid);
if (bar == NULL)
return (ENXIO);
/* Set DLAB in the LCR register of UART 0. */
bus_write_1(bar->b_res, 3, 0x80);
/* Write 0 to the SPR register of UART 0. */
bus_write_1(bar->b_res, 7, 0);
/* Read back the contents of the SPR register of UART 0. */
v0 = bus_read_1(bar->b_res, 7);
/* Write a specific value to the SPR register of UART 0. */
bus_write_1(bar->b_res, 7, 0x80 + -cfg->clock);
/* Read back the contents of the SPR register of UART 0. */
v1 = bus_read_1(bar->b_res, 7);
/* Clear DLAB in the LCR register of UART 0. */
bus_write_1(bar->b_res, 3, 0);
/* Save the two values read-back from the SPR register. */
sc->sc_cfg_data = (v0 << 8) | v1;
if (v0 == 0 && v1 == 0x80 + -cfg->clock) {
/*
* The SPR register echoed the two values written
* by us. This means that the SPAD jumper is set.
*/
device_printf(sc->sc_dev, "warning: extra features "
"not usable -- SPAD compatibility enabled\n");
return (0);
}
if (v0 != 0) {
/*
* The first value doesn't match. This can only mean
* that the SPAD jumper is not set and that a non-
* standard fixed clock multiplier jumper is set.
*/
if (bootverbose)
device_printf(sc->sc_dev, "fixed clock rate "
"multiplier of %d\n", 1 << v0);
if (v0 < -cfg->clock)
device_printf(sc->sc_dev, "warning: "
"suboptimal fixed clock rate multiplier "
"setting\n");
return (0);
}
/*
* The first value matched, but the second didn't. We know
* that the SPAD jumper is not set. We also know that the
* clock rate multiplier is software controlled *and* that
* we just programmed it to the maximum allowed.
*/
if (bootverbose)
device_printf(sc->sc_dev, "clock rate multiplier of "
"%d selected\n", 1 << -cfg->clock);
return (0);
case PUC_CFG_GET_CLOCK:
v0 = (sc->sc_cfg_data >> 8) & 0xff;
v1 = sc->sc_cfg_data & 0xff;
if (v0 == 0 && v1 == 0x80 + -cfg->clock) {
/*
* XXX With the SPAD jumper applied, there's no
* easy way of knowing if there's also a clock
* rate multiplier jumper installed. Let's hope
* not...
*/
*res = DEFAULT_RCLK;
} else if (v0 == 0) {
/*
* No clock rate multiplier jumper installed,
* so we programmed the board with the maximum
* multiplier allowed as given to us in the
* clock field of the config record (negated).
*/
*res = DEFAULT_RCLK << -cfg->clock;
} else
*res = DEFAULT_RCLK << v0;
return (0);
case PUC_CFG_GET_ILR:
v0 = (sc->sc_cfg_data >> 8) & 0xff;
v1 = sc->sc_cfg_data & 0xff;
*res = (v0 == 0 && v1 == 0x80 + -cfg->clock)
? PUC_ILR_NONE : PUC_ILR_QUATECH;
return (0);
default:
break;
}
return (ENXIO);
}
static int
puc_config_syba(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
static int base[] = { 0x251, 0x3f0, 0 };
const struct puc_cfg *cfg = sc->sc_cfg;
struct puc_bar *bar;
int efir, idx, ofs;
uint8_t v;
switch (cmd) {
case PUC_CFG_SETUP:
bar = puc_get_bar(sc, cfg->rid);
if (bar == NULL)
return (ENXIO);
/* configure both W83877TFs */
bus_write_1(bar->b_res, 0x250, 0x89);
bus_write_1(bar->b_res, 0x3f0, 0x87);
bus_write_1(bar->b_res, 0x3f0, 0x87);
idx = 0;
while (base[idx] != 0) {
efir = base[idx];
bus_write_1(bar->b_res, efir, 0x09);
v = bus_read_1(bar->b_res, efir + 1);
if ((v & 0x0f) != 0x0c)
return (ENXIO);
bus_write_1(bar->b_res, efir, 0x16);
v = bus_read_1(bar->b_res, efir + 1);
bus_write_1(bar->b_res, efir, 0x16);
bus_write_1(bar->b_res, efir + 1, v | 0x04);
bus_write_1(bar->b_res, efir, 0x16);
bus_write_1(bar->b_res, efir + 1, v & ~0x04);
ofs = base[idx] & 0x300;
bus_write_1(bar->b_res, efir, 0x23);
bus_write_1(bar->b_res, efir + 1, (ofs + 0x78) >> 2);
bus_write_1(bar->b_res, efir, 0x24);
bus_write_1(bar->b_res, efir + 1, (ofs + 0xf8) >> 2);
bus_write_1(bar->b_res, efir, 0x25);
bus_write_1(bar->b_res, efir + 1, (ofs + 0xe8) >> 2);
bus_write_1(bar->b_res, efir, 0x17);
bus_write_1(bar->b_res, efir + 1, 0x03);
bus_write_1(bar->b_res, efir, 0x28);
bus_write_1(bar->b_res, efir + 1, 0x43);
idx++;
}
bus_write_1(bar->b_res, 0x250, 0xaa);
bus_write_1(bar->b_res, 0x3f0, 0xaa);
return (0);
case PUC_CFG_GET_OFS:
switch (port) {
case 0:
*res = 0x2f8;
return (0);
case 1:
*res = 0x2e8;
return (0);
case 2:
*res = 0x3f8;
return (0);
case 3:
*res = 0x3e8;
return (0);
case 4:
*res = 0x278;
return (0);
}
break;
default:
break;
}
return (ENXIO);
}
static int
puc_config_siig(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
const struct puc_cfg *cfg = sc->sc_cfg;
switch (cmd) {
case PUC_CFG_GET_OFS:
if (cfg->ports == PUC_PORT_8S) {
*res = (port > 4) ? 8 * (port - 4) : 0;
return (0);
}
break;
case PUC_CFG_GET_RID:
if (cfg->ports == PUC_PORT_8S) {
*res = 0x10 + ((port > 4) ? 0x10 : 4 * port);
return (0);
}
if (cfg->ports == PUC_PORT_2S1P) {
switch (port) {
case 0: *res = 0x10; return (0);
case 1: *res = 0x14; return (0);
case 2: *res = 0x1c; return (0);
}
}
break;
default:
break;
}
return (ENXIO);
}
static int
puc_config_timedia(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
static const uint16_t dual[] = {
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
0x0002, 0x4036, 0x4037, 0x4038, 0x4078, 0x4079, 0x4085,
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
0x4088, 0x4089, 0x5037, 0x5078, 0x5079, 0x5085, 0x6079,
0x7079, 0x8079, 0x8137, 0x8138, 0x8237, 0x8238, 0x9079,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
0x9137, 0x9138, 0x9237, 0x9238, 0xA079, 0xB079, 0xC079,
0xD079, 0
};
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
static const uint16_t quad[] = {
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
0x4055, 0x4056, 0x4095, 0x4096, 0x5056, 0x8156, 0x8157,
0x8256, 0x8257, 0x9056, 0x9156, 0x9157, 0x9158, 0x9159,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
0x9256, 0x9257, 0xA056, 0xA157, 0xA158, 0xA159, 0xB056,
0xB157, 0
};
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
static const uint16_t octa[] = {
Fix whitespace and normalize some entries.
2013-06-13 21:47:22 +00:00
0x4065, 0x4066, 0x5065, 0x5066, 0x8166, 0x9066, 0x9166,
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
0x9167, 0x9168, 0xA066, 0xA167, 0xA168, 0
};
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
static const struct {
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
int ports;
- Apparently, r186520 was just wrong and the clock of Oxford OX16PCI958 is neither DEFAULT_RCLK * 2 nor DEFAULT_RCLK * 10 but plain DEFAULT_RCLK and there's no (open) source indicating otherwise. This was tested with an EXSYS EX-41098-2, whose clock is not configurable and identifies as: puc0@pci0:5:1:0: class=0x070200 card=0x06711415 chip=0x95381415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' class = simple comms subclass = multiport serial Note that this exactly matches the card mentioned in PR 129665 so no sub-device/sub-vendor based quirking of the latter is possible. So maybe we should grow some sort of tunable, in case non-default cards such as the latter aren't configurable either (this also wouldn't be the first time an allegedly tested commit turns out to be wrong though). - Make the TiMedia tables const. MFC after: 1 week
2013-03-01 20:16:06 +00:00
const uint16_t *ids;
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
} subdevs[] = {
{ 2, dual },
{ 4, quad },
{ 8, octa },
{ 0, NULL }
};
static char desc[64];
int dev, id;
uint16_t subdev;
switch (cmd) {
For Timedia multiport serial adapters, the first two ports use a SUN1889 which uses a non-standard clock (* 8) while any additional ports use SUN1699 chips which use a standard clock. Tested by: N.J. Mann njm of njm me uk MFC after: 1 week
2011-05-26 20:54:45 +00:00
case PUC_CFG_GET_CLOCK:
if (port < 2)
*res = DEFAULT_RCLK * 8;
else
*res = DEFAULT_RCLK;
return (0);
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
case PUC_CFG_GET_DESC:
snprintf(desc, sizeof(desc),
"Timedia technology %d Port Serial", (int)sc->sc_cfg_data);
*res = (intptr_t)desc;
return (0);
case PUC_CFG_GET_NPORTS:
subdev = pci_get_subdevice(sc->sc_dev);
dev = 0;
while (subdevs[dev].ports != 0) {
id = 0;
while (subdevs[dev].ids[id] != 0) {
if (subdev == subdevs[dev].ids[id]) {
sc->sc_cfg_data = subdevs[dev].ports;
*res = sc->sc_cfg_data;
return (0);
}
id++;
}
dev++;
}
return (ENXIO);
case PUC_CFG_GET_OFS:
*res = (port == 1 || port == 3) ? 8 : 0;
return (0);
case PUC_CFG_GET_RID:
Fix RID calculation. The RID is really the BAR for PCI cards, so the index needs to be translated into an offset. While we did add the offset (0x10), we forgot to account for the width. Tested by: Thomas Vogt MFC after: 3 days
2008-05-16 14:57:48 +00:00
*res = 0x10 + ((port > 3) ? port - 2 : port >> 1) * 4;
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
return (0);
case PUC_CFG_GET_TYPE:
*res = PUC_TYPE_SERIAL;
return (0);
default:
break;
}
return (ENXIO);
}
All of Oxford/PLX OX16PCI954, OXm16PCI954 and OXu16PCI954 share the exact same (subsystem) device and vendor IDs. However, the reference design for the OXu16PCI954 uses a 14.7456 MHz clock (as does the EXSYS EX-41098-2 equipped with these), while at least the OX16PCI954 defaults to a 1.8432 MHz one. According to the datasheets of these chips, the only difference in PCI configuration space is that OXu16PCI954 have a revision ID of 1 while the other two are at 0. So employ the latter for determining the default clock rates of this family. Note that one might think that the actual clock could be derived from the Clock Prescaler Register (CPR) of these chips. Unfortunately, this is not that case and its use and content are orthogonal to the frequency of the crystal employed. Tested with an EXSYS EX-41098-2, which identifies and attaches as: pcib4@pci0:19:0:0: class=0x060400 card=0x02dd1014 chip=0x10801b21 rev=0x03 hdr=0x01 vendor = 'ASMedia Technology Inc.' device = 'ASM1083/1085 PCIe to PCI Bridge' class = bridge subclass = PCI-PCI puc0@pci0:20:4:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc1@pci0:20:4:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge puc2@pci0:20:8:0: class=0x070006 card=0x00001415 chip=0x95011415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 0 (Uart)' class = simple comms subclass = UART puc3@pci0:20:8:1: class=0x068000 card=0x00001415 chip=0x95111415 rev=0x01 hdr=0x00 vendor = 'Oxford Semiconductor Ltd' device = 'OX16PCI954 (Quad 16950 UART) function 1 (8bit bus)' class = bridge pci20: <ACPI PCI bus> on pcib4 puc0: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5000-0x501f, 0x5020-0x503f mem 0xc6000000-0xc6000fff,0xc6001000-0xc6001fff irq 16 at device 4.0 on pci20 uart1: <16950 or compatible> at port 1 on puc0 uart2: <16950 or compatible> at port 2 on puc0 uart3: <16950 or compatible> at port 3 on puc0 uart4: <16950 or compatible> at port 4 on puc0 puc1: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x5040-0x505f,0x5060-0x507f mem 0xc6002000-0xc6002fff,0xc6003000-0xc6003fff irq 16 at device 4.1 on pci20 puc2: <Oxford Semiconductor OX16PCI954 UARTs> port 0x5080-0x509f, 0x50a0-0x50bf mem 0xc6004000-0xc6004fff,0xc6005000-0xc6005fff irq 16 at device 8.0 on pci20 uart5: <16950 or compatible> at port 1 on puc2 uart6: <16950 or compatible> at port 2 on puc2 uart7: <16950 or compatible> at port 3 on puc2 uart8: <16950 or compatible> at port 4 on puc2 puc3: <Oxford Semiconductor OX9160/OX16PCI954 UARTs (function 1)> port 0x50c0-0x50df,0x50e0-0x50ff mem 0xc6006000-0xc6006fff,0xc6007000-0xc6007fff irq 16 at device 8.1 on pci20 MFC after: 2 weeks
2013-06-13 22:13:41 +00:00
static int
puc_config_oxford_pci954(struct puc_softc *sc, enum puc_cfg_cmd cmd,
int port __unused, intptr_t *res)
{
switch (cmd) {
case PUC_CFG_GET_CLOCK:
/*
* OXu16PCI954 use a 14.7456 MHz clock by default while
* OX16PCI954 and OXm16PCI954 employ a 1.8432 MHz one.
*/
if (pci_get_revid(sc->sc_dev) == 1)
*res = DEFAULT_RCLK * 8;
else
*res = DEFAULT_RCLK;
return (0);
default:
break;
}
return (ENXIO);
}
Add support for Oxford PCI Express Expresso family devices. For these devices, the number of supported ports is read from a register in BAR 0. PR: kern/134878 Submitted by: David Wood david of wood2 org uk MFC after: 1 week
2011-04-28 19:19:25 +00:00
static int
puc_config_oxford_pcie(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
const struct puc_cfg *cfg = sc->sc_cfg;
int idx;
struct puc_bar *bar;
uint8_t value;
switch (cmd) {
case PUC_CFG_SETUP:
device_printf(sc->sc_dev, "%d UARTs detected\n",
sc->sc_nports);
/* Set UARTs to enhanced mode */
bar = puc_get_bar(sc, cfg->rid);
if (bar == NULL)
return (ENXIO);
for (idx = 0; idx < sc->sc_nports; idx++) {
Some style fixes. Submitted by: bde
2011-06-06 15:33:15 +00:00
value = bus_read_1(bar->b_res, 0x1000 + (idx << 9) +
0x92);
Add support for Oxford PCI Express Expresso family devices. For these devices, the number of supported ports is read from a register in BAR 0. PR: kern/134878 Submitted by: David Wood david of wood2 org uk MFC after: 1 week
2011-04-28 19:19:25 +00:00
bus_write_1(bar->b_res, 0x1000 + (idx << 9) + 0x92,
Some style fixes. Submitted by: bde
2011-06-06 15:33:15 +00:00
value | 0x10);
Add support for Oxford PCI Express Expresso family devices. For these devices, the number of supported ports is read from a register in BAR 0. PR: kern/134878 Submitted by: David Wood david of wood2 org uk MFC after: 1 week
2011-04-28 19:19:25 +00:00
}
return (0);
case PUC_CFG_GET_LEN:
*res = 0x200;
return (0);
case PUC_CFG_GET_NPORTS:
/*
* Check if we are being called from puc_bfe_attach()
* or puc_bfe_probe(). If puc_bfe_probe(), we cannot
* puc_get_bar(), so we return a value of 16. This has cosmetic
* side-effects at worst; in PUC_CFG_GET_DESC,
* (int)sc->sc_cfg_data will not contain the true number of
* ports in PUC_CFG_GET_DESC, but we are not implementing that
* call for this device family anyway.
*
* The check is for initialisation of sc->sc_bar[idx], which is
* only done in puc_bfe_attach().
*/
idx = 0;
do {
if (sc->sc_bar[idx++].b_rid != -1) {
sc->sc_cfg_data = 16;
*res = sc->sc_cfg_data;
return (0);
}
} while (idx < PUC_PCI_BARS);
bar = puc_get_bar(sc, cfg->rid);
if (bar == NULL)
return (ENXIO);
value = bus_read_1(bar->b_res, 0x04);
if (value == 0)
return (ENXIO);
sc->sc_cfg_data = value;
*res = sc->sc_cfg_data;
return (0);
case PUC_CFG_GET_OFS:
*res = 0x1000 + (port << 9);
return (0);
case PUC_CFG_GET_TYPE:
*res = PUC_TYPE_SERIAL;
return (0);
default:
break;
}
return (ENXIO);
}
Distinguish between the different variants and configurations of Sunix {MIO,SER}5xxxx chips instead of treating all of them as PUC_PORT_2S. Among others, this fixes the hang seen when trying to probe the none- existent second UART on an actually 1-port chip. Obtained from: NetBSD (BAR layouts) MFC after: 3 days Sponsored by: Bally Wulff Games & Entertainment GmbH
2014-04-08 07:32:32 +00:00
static int
puc_config_sunix(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
int error;
switch (cmd) {
case PUC_CFG_GET_OFS:
error = puc_config(sc, PUC_CFG_GET_TYPE, port, res);
if (error != 0)
return (error);
*res = (*res == PUC_TYPE_SERIAL) ? (port & 3) * 8 : 0;
return (0);
case PUC_CFG_GET_RID:
error = puc_config(sc, PUC_CFG_GET_TYPE, port, res);
if (error != 0)
return (error);
*res = (*res == PUC_TYPE_SERIAL && port <= 3) ? 0x10 : 0x14;
return (0);
default:
break;
}
return (ENXIO);
}
Rewrite of puc(4). Significant changes are: o Properly use rman(9) to manage resources. This eliminates the need to puc-specific hacks to rman. It also allows devinfo(8) to be used to find out the specific assignment of resources to serial/parallel ports. o Compress the PCI device "database" by optimizing for the common case and to use a procedural interface to handle the exceptions. The procedural interface also generalizes the need to setup the hardware (program chipsets, program clock frequencies). o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by default and non-serdev devices are handled by the bus. o Use the serdev I/F to collect interrupt status and to handle interrupts across ports in priority order. o Sync the PCI device configuration to include devices found in NetBSD and not yet merged to FreeBSD. o Add support for Quatech 2, 4 and 8 port UARTs. o Add support for a couple dozen Timedia serial cards as found in Linux.
2006-04-28 21:21:53 +00:00
static int
puc_config_titan(struct puc_softc *sc, enum puc_cfg_cmd cmd, int port,
intptr_t *res)
{
switch (cmd) {
case PUC_CFG_GET_OFS:
*res = (port < 3) ? 0 : (port - 2) << 3;
return (0);
case PUC_CFG_GET_RID:
*res = 0x14 + ((port >= 2) ? 0x0c : port << 2);
return (0);
default:
break;
}
return (ENXIO);
}
Reference in New Issue Copy Permalink