d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
1ce07411fa
freebsd-nq/sys/dev/mii/nsphy.c

328 lines
9.2 KiB
C
Raw Normal View History

This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/* $NetBSD: nsphy.c,v 1.18 1999/07/14 23:57:36 thorpej Exp $ */
/*-
sys/dev: further adoption of SPDX licensing ID tags. Mainly focus on files that use BSD 2-Clause license, however the tool I was using misidentified many licenses so this was mostly a manual - error prone - task. The Software Package Data Exchange (SPDX) group provides a specification to make it easier for automated tools to detect and summarize well known opensource licenses. We are gradually adopting the specification, noting that the tags are considered only advisory and do not, in any way, superceed or replace the license texts.
2017-11-27 14:52:40 +00:00
* SPDX-License-Identifier: BSD-2-Clause-NetBSD AND BSD-2-Clause
*
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
* Copyright (c) 1998, 1999 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
* NASA Ames Research Center.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
Start each of the license/copyright comments with /*-, minor shuffle of lines
2005-01-06 01:43:34 +00:00
/*-
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
* Copyright (c) 1997 Manuel Bouyer. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
Remove double __FBSDID and move the remaining one into a common place after the license(s) and before the driver comment (the latter only in drivers not having __FBSDID at that location).
2004-05-29 18:09:10 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/*
* driver for National Semiconductor's DP83840A ethernet 10/100 PHY
* Data Sheet available from www.national.com
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/errno.h>
#include <sys/module.h>
#include <sys/bus.h>
#include <net/if.h>
The MII layer shouldn't care about administrative status of an interface. Make MII drivers forget about 'struct ifnet'. Later plan is to provide an administrative downcall from ifnet layer into drivers, to inform them about administrative status change. If someone thinks that processing MII events for an administratively down interface is a big problem, then drivers would turn MII processing off. The following MII drivers do evil things, like strcmp() on driver name, so they still need knowledge of ifnet and thus include if_var.h. They all need to be fixed: sys/dev/mii/brgphy.c sys/dev/mii/e1000phy.c sys/dev/mii/ip1000phy.c sys/dev/mii/jmphy.c sys/dev/mii/nsphy.c sys/dev/mii/rgephy.c sys/dev/mii/truephy.c Sponsored by: Netflix Sponsored by: Nginx, Inc.
2013-10-26 18:40:17 +00:00
#include <net/if_var.h>
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
Remove miidevs.h and generate it from miidevs at compile time. The devlist2h.awk tool to do this has been repocopied to sys/tools/.
2003-01-19 02:59:34 +00:00
#include "miidevs.h"
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#include <dev/mii/nsphyreg.h>
#include "miibus_if.h"
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int nsphy_probe(device_t);
static int nsphy_attach(device_t);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
static device_method_t nsphy_methods[] = {
/* device interface */
DEVMETHOD(device_probe, nsphy_probe),
DEVMETHOD(device_attach, nsphy_attach),
Make one generic mii_phy_detach() to replace 19 slightly different ones. Rename mii_phy_auto_stop() mii_phy_down(). Introduce mii_down(), use it from nge. Do not indirect it to 19 identical case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
DEVMETHOD(device_detach, mii_phy_detach),
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
DEVMETHOD(device_shutdown, bus_generic_shutdown),
Use DEVMETHOD_END.
2011-11-23 20:27:26 +00:00
DEVMETHOD_END
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
};
static devclass_t nsphy_devclass;
static driver_t nsphy_driver = {
"nsphy",
nsphy_methods,
sizeof(struct mii_softc)
};
DRIVER_MODULE(nsphy, miibus, nsphy_driver, nsphy_devclass, 0, 0);
Remove __P.
2002-03-20 02:08:01 +00:00
static int nsphy_service(struct mii_softc *, struct mii_data *, int);
static void nsphy_status(struct mii_softc *);
- Don't add IFM_NONE when used in combination with pcn(4) as for MII loopback to work PCnet chips additionally need to be placed into external loopback mode which pcn(4) doesn't do so far. - In nsphy_service() just use if_dname instead of determining the name of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)). - Don't set MIIF_NOISOLATE, except for when used in combination with a NIC that wedges when isolating the PHYs, so nsphy(4) can be used in configurations with multiple PHYs. - Use mii_phy_add_media() instead of mii_add_media() so the latter can be eventually retired. - Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19). - Implement a separate nsphy_reset(). There are two reasons for this: 1) This PHY can take an inordinate amount of time to reset if media is attached; under fairly normal circumstances up to nearly one second. This is because it appears to go through an implicit auto- negotiation cycle as part of the reset. 2) During reset and auto-negotiation, the BMCR will clear the reset bit before the process is complete. It will return 0 until the process is complete and it's safe to access the PHY again. This is the first of two changes required to make the combination of Am79c971 and DP83840A found on certain HP cards and on-board in IBM machines work. - Fix some whitespace nits. Based on: NetBSD (except for the first and second item) MFC after: 2 weeks
2006-11-28 01:01:02 +00:00
static void nsphy_reset(struct mii_softc *);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
Add a helper function mii_phy_dev_probe(), which wraps around the mii_phy_match() API and takes care of the PHY device probe based on the struct mii_phydesc array and the match return value provided. Convert PHY drivers to take advantage of mii_phy_dev_probe(), converting drivers to provide a mii_phydesc table in the first place where necessary. Reviewed by: yongari MFC after: 2 weeks
2006-12-02 15:32:34 +00:00
static const struct mii_phydesc nsphys[] = {
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MII_PHY_DESC(xxNATSEMI, DP83840),
Add a helper function mii_phy_dev_probe(), which wraps around the mii_phy_match() API and takes care of the PHY device probe based on the struct mii_phydesc array and the match return value provided. Convert PHY drivers to take advantage of mii_phy_dev_probe(), converting drivers to provide a mii_phydesc table in the first place where necessary. Reviewed by: yongari MFC after: 2 weeks
2006-12-02 15:32:34 +00:00
MII_PHY_END
};
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
static const struct mii_phy_funcs nsphy_funcs = {
nsphy_service,
nsphy_status,
nsphy_reset
};
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
nsphy_probe(device_t dev)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
Add a helper function mii_phy_dev_probe(), which wraps around the mii_phy_match() API and takes care of the PHY device probe based on the struct mii_phydesc array and the match return value provided. Convert PHY drivers to take advantage of mii_phy_dev_probe(), converting drivers to provide a mii_phydesc table in the first place where necessary. Reviewed by: yongari MFC after: 2 weeks
2006-12-02 15:32:34 +00:00
return (mii_phy_dev_probe(dev, nsphys, BUS_PROBE_DEFAULT));
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
}
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
nsphy_attach(device_t dev)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
u_int flags;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
flags = MIIF_NOMANPAUSE;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/*
Convert the PHY drivers to honor the mii_flags passed down and convert the NIC drivers as well as the PHY drivers to take advantage of the mii_attach() introduced in r213878 to get rid of certain hacks. For the most part these were: - Artificially limiting miibus_{read,write}reg methods to certain PHY addresses; we now let mii_attach() only probe the PHY at the desired address(es) instead. - PHY drivers setting MIIF_* flags based on the NIC driver they hang off from, partly even based on grabbing and using the softc of the parent; we now pass these flags down from the NIC to the PHY drivers via mii_attach(). This got us rid of all such hacks except those of brgphy() in combination with bce(4) and bge(4), which is way beyond what can be expressed with simple flags. While at it, I took the opportunity to change the NIC drivers to pass up the error returned by mii_attach() (previously by mii_phy_probe()) and unify the error message used in this case where and as appropriate as mii_attach() actually can fail for a number of reasons, not just because of no PHY(s) being present at the expected address(es). Reviewed by: jhb, yongari
2010-10-15 14:52:11 +00:00
* Am79C971 wedge when isolating all of their external PHYs.
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
*/
In miibus(4) drivers provide functions that allow to get NIC driver name and NIC driver softc via the device(9) tree, instead of going dirty through the ifnet(9) layer. Differential Revision: D1506 Reviewed by: imp, jhb
2015-01-12 22:27:38 +00:00
if (mii_dev_mac_match(dev,"pcn"))
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
flags |= MIIF_NOISOLATE;
mii_phy_dev_attach(dev, flags, &nsphy_funcs, 1);
- Don't add IFM_NONE when used in combination with pcn(4) as for MII loopback to work PCnet chips additionally need to be placed into external loopback mode which pcn(4) doesn't do so far. - In nsphy_service() just use if_dname instead of determining the name of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)). - Don't set MIIF_NOISOLATE, except for when used in combination with a NIC that wedges when isolating the PHYs, so nsphy(4) can be used in configurations with multiple PHYs. - Use mii_phy_add_media() instead of mii_add_media() so the latter can be eventually retired. - Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19). - Implement a separate nsphy_reset(). There are two reasons for this: 1) This PHY can take an inordinate amount of time to reset if media is attached; under fairly normal circumstances up to nearly one second. This is because it appears to go through an implicit auto- negotiation cycle as part of the reset. 2) During reset and auto-negotiation, the BMCR will clear the reset bit before the process is complete. It will return 0 until the process is complete and it's safe to access the PHY again. This is the first of two changes required to make the combination of Am79c971 and DP83840A found on certain HP cards and on-board in IBM machines work. - Fix some whitespace nits. Based on: NetBSD (except for the first and second item) MFC after: 2 weeks
2006-11-28 01:01:02 +00:00
return (0);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static int
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
nsphy_service(struct mii_softc *sc, struct mii_data *mii, int cmd)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
int reg;
switch (cmd) {
case MII_POLLSTAT:
break;
case MII_MEDIACHG:
reg = PHY_READ(sc, MII_NSPHY_PCR);
/*
* Set up the PCR to use LED4 to indicate full-duplex
* in both 10baseT and 100baseTX modes.
*/
reg |= PCR_LED4MODE;
/*
Spelling fix in a comment.
2004-05-29 16:54:59 +00:00
* Make sure Carrier Integrity Monitor function is
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
* disabled (normal for Node operation, but sometimes
* it's not set?!)
*/
reg |= PCR_CIMDIS;
/*
* Make sure "force link good" is set to normal mode.
* It's only intended for debugging.
*/
reg |= PCR_FLINK100;
/*
* Mystery bits which are supposedly `reserved',
* but we seem to need to set them when the PHY
Enable some undocumented bits in the DP83840 PHY, which is needed when using it with the Intel fxp driver. Tested by: peter, Ollivier Robert <roberto@eurocontrol.fr>, Peter Schultz <pete@jocose.org>
2001-03-16 14:17:02 +00:00
* is connected to some interfaces:
*
* 0x0400 is needed for fxp
* (Intel EtherExpress Pro 10+/100B, 82557 chip)
* (nsphy with a DP83840 chip)
* 0x0100 may be needed for some other card
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
*/
reg |= 0x0100 | 0x0400;
Enable some undocumented bits in the DP83840 PHY, which is needed when using it with the Intel fxp driver. Tested by: peter, Ollivier Robert <roberto@eurocontrol.fr>, Peter Schultz <pete@jocose.org>
2001-03-16 14:17:02 +00:00
In miibus(4) drivers provide functions that allow to get NIC driver name and NIC driver softc via the device(9) tree, instead of going dirty through the ifnet(9) layer. Differential Revision: D1506 Reviewed by: imp, jhb
2015-01-12 22:27:38 +00:00
if (mii_phy_mac_match(sc, "fxp"))
Only touch the PCR register in order to set bits for the fxp driver. The 3C509-TX card apparently had a slightly different version of the chip, and has problems when this register is set. The problem does not appear on the 3C509{BC} cards, but since only the fxp driver needs specific bits set, conditionalize on that.
2001-06-02 19:51:02 +00:00
PHY_WRITE(sc, MII_NSPHY_PCR, reg);
Enable some undocumented bits in the DP83840 PHY, which is needed when using it with the Intel fxp driver. Tested by: peter, Ollivier Robert <roberto@eurocontrol.fr>, Peter Schultz <pete@jocose.org>
2001-03-16 14:17:02 +00:00
- Don't add IFM_NONE when used in combination with pcn(4) as for MII loopback to work PCnet chips additionally need to be placed into external loopback mode which pcn(4) doesn't do so far. - In nsphy_service() just use if_dname instead of determining the name of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)). - Don't set MIIF_NOISOLATE, except for when used in combination with a NIC that wedges when isolating the PHYs, so nsphy(4) can be used in configurations with multiple PHYs. - Use mii_phy_add_media() instead of mii_add_media() so the latter can be eventually retired. - Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19). - Implement a separate nsphy_reset(). There are two reasons for this: 1) This PHY can take an inordinate amount of time to reset if media is attached; under fairly normal circumstances up to nearly one second. This is because it appears to go through an implicit auto- negotiation cycle as part of the reset. 2) During reset and auto-negotiation, the BMCR will clear the reset bit before the process is complete. It will return 0 until the process is complete and it's safe to access the PHY again. This is the first of two changes required to make the combination of Am79c971 and DP83840A found on certain HP cards and on-board in IBM machines work. - Fix some whitespace nits. Based on: NetBSD (except for the first and second item) MFC after: 2 weeks
2006-11-28 01:01:02 +00:00
mii_phy_setmedia(sc);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
break;
case MII_TICK:
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
if (mii_phy_tick(sc) == EJUSTRETURN)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
break;
}
/* Update the media status. */
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
PHY_STATUS(sc);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/* Callback if something changed. */
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
mii_phy_update(sc, cmd);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static void
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
nsphy_status(struct mii_softc *sc)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
{
struct mii_data *mii = sc->mii_pdata;
- Don't add IFM_NONE when used in combination with pcn(4) as for MII loopback to work PCnet chips additionally need to be placed into external loopback mode which pcn(4) doesn't do so far. - In nsphy_service() just use if_dname instead of determining the name of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)). - Don't set MIIF_NOISOLATE, except for when used in combination with a NIC that wedges when isolating the PHYs, so nsphy(4) can be used in configurations with multiple PHYs. - Use mii_phy_add_media() instead of mii_add_media() so the latter can be eventually retired. - Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19). - Implement a separate nsphy_reset(). There are two reasons for this: 1) This PHY can take an inordinate amount of time to reset if media is attached; under fairly normal circumstances up to nearly one second. This is because it appears to go through an implicit auto- negotiation cycle as part of the reset. 2) During reset and auto-negotiation, the BMCR will clear the reset bit before the process is complete. It will return 0 until the process is complete and it's safe to access the PHY again. This is the first of two changes required to make the combination of Am79c971 and DP83840A found on certain HP cards and on-board in IBM machines work. - Fix some whitespace nits. Based on: NetBSD (except for the first and second item) MFC after: 2 weeks
2006-11-28 01:01:02 +00:00
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
int bmsr, bmcr, par, anlpar;
mii->mii_media_status = IFM_AVALID;
mii->mii_media_active = IFM_ETHER;
bmsr = PHY_READ(sc, MII_BMSR) |
PHY_READ(sc, MII_BMSR);
if (bmsr & BMSR_LINK)
mii->mii_media_status |= IFM_ACTIVE;
bmcr = PHY_READ(sc, MII_BMCR);
if (bmcr & BMCR_ISO) {
mii->mii_media_active |= IFM_NONE;
mii->mii_media_status = 0;
return;
}
if (bmcr & BMCR_LOOP)
mii->mii_media_active |= IFM_LOOP;
if (bmcr & BMCR_AUTOEN) {
/*
- Fix a typo in a comment. - Fix whitespace according to style(9). - Sync the comment describing why we have to wait in nsphy_reset() with nsphyter_reset(). It's true that the manual tells to not do a reset within 500us of applying power but that's unlikely the cause of problems seen here. Generally having to wait 500us after a reset however is.
2008-01-27 01:30:02 +00:00
* The PAR status bits are only valid if autonegotiation
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
* has completed (or it's disabled).
*/
if ((bmsr & BMSR_ACOMP) == 0) {
/* Erg, still trying, I guess... */
mii->mii_media_active |= IFM_NONE;
return;
}
/*
* Argh. The PAR doesn't seem to indicate duplex mode
* properly! Determine media based on link partner's
* advertised capabilities.
*/
if (PHY_READ(sc, MII_ANER) & ANER_LPAN) {
anlpar = PHY_READ(sc, MII_ANAR) &
PHY_READ(sc, MII_ANLPAR);
IEEE 802.3 Annex 28B.3 explicitly specifies the following relative priorities of the technologies supported by 802.3 Selector Field value. 1000BASE-T full duplex 1000BASE-T 100BASE-T2 full duplex 100BASE-TX full duplex 100BASE-T2 100BASE-T4 100BASE-TX 10BASE-T full duplex 10BAST-T However PHY drivers didn't honor the order such that 100BASE-T4 had higher priority than 100BASE-TX full duplex. Fix that long standing bugs such that have PHY drivers choose the highest common denominator ability. Fix a bug in dcphy which inadvertently aceepts 100BASE-T4. PR: 92599
2007-11-16 10:25:36 +00:00
if (anlpar & ANLPAR_TX_FD)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
mii->mii_media_active |= IFM_100_TX|IFM_FDX;
IEEE 802.3 Annex 28B.3 explicitly specifies the following relative priorities of the technologies supported by 802.3 Selector Field value. 1000BASE-T full duplex 1000BASE-T 100BASE-T2 full duplex 100BASE-TX full duplex 100BASE-T2 100BASE-T4 100BASE-TX 10BASE-T full duplex 10BAST-T However PHY drivers didn't honor the order such that 100BASE-T4 had higher priority than 100BASE-TX full duplex. Fix that long standing bugs such that have PHY drivers choose the highest common denominator ability. Fix a bug in dcphy which inadvertently aceepts 100BASE-T4. PR: 92599
2007-11-16 10:25:36 +00:00
else if (anlpar & ANLPAR_T4)
Consistently always explicitly set IFM_HDX for half-duplex. Obtained from: OpenBSD (mostly)
2010-10-03 17:00:57 +00:00
mii->mii_media_active |= IFM_100_T4|IFM_HDX;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
else if (anlpar & ANLPAR_TX)
Consistently always explicitly set IFM_HDX for half-duplex. Obtained from: OpenBSD (mostly)
2010-10-03 17:00:57 +00:00
mii->mii_media_active |= IFM_100_TX|IFM_HDX;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
else if (anlpar & ANLPAR_10_FD)
mii->mii_media_active |= IFM_10_T|IFM_FDX;
else if (anlpar & ANLPAR_10)
Consistently always explicitly set IFM_HDX for half-duplex. Obtained from: OpenBSD (mostly)
2010-10-03 17:00:57 +00:00
mii->mii_media_active |= IFM_10_T|IFM_HDX;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
else
mii->mii_media_active |= IFM_NONE;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if ((mii->mii_media_active & IFM_FDX) != 0)
mii->mii_media_active |=
mii_phy_flowstatus(sc);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return;
}
/*
* Link partner is not capable of autonegotiation.
* We will never be in full-duplex mode if this is
* the case, so reading the PAR is OK.
*/
par = PHY_READ(sc, MII_NSPHY_PAR);
if (par & PAR_10)
mii->mii_media_active |= IFM_10_T;
else
mii->mii_media_active |= IFM_100_TX;
Consistently always explicitly set IFM_HDX for half-duplex. Obtained from: OpenBSD (mostly)
2010-10-03 17:00:57 +00:00
mii->mii_media_active |= IFM_HDX;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
} else
- Don't add IFM_NONE when used in combination with pcn(4) as for MII loopback to work PCnet chips additionally need to be placed into external loopback mode which pcn(4) doesn't do so far. - In nsphy_service() just use if_dname instead of determining the name of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)). - Don't set MIIF_NOISOLATE, except for when used in combination with a NIC that wedges when isolating the PHYs, so nsphy(4) can be used in configurations with multiple PHYs. - Use mii_phy_add_media() instead of mii_add_media() so the latter can be eventually retired. - Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19). - Implement a separate nsphy_reset(). There are two reasons for this: 1) This PHY can take an inordinate amount of time to reset if media is attached; under fairly normal circumstances up to nearly one second. This is because it appears to go through an implicit auto- negotiation cycle as part of the reset. 2) During reset and auto-negotiation, the BMCR will clear the reset bit before the process is complete. It will return 0 until the process is complete and it's safe to access the PHY again. This is the first of two changes required to make the combination of Am79c971 and DP83840A found on certain HP cards and on-board in IBM machines work. - Fix some whitespace nits. Based on: NetBSD (except for the first and second item) MFC after: 2 weeks
2006-11-28 01:01:02 +00:00
mii->mii_media_active = ife->ifm_media;
}
static void
nsphy_reset(struct mii_softc *sc)
{
struct ifmedia_entry *ife = sc->mii_pdata->mii_media.ifm_cur;
int reg, i;
if (sc->mii_flags & MIIF_NOISOLATE)
reg = BMCR_RESET;
else
reg = BMCR_RESET | BMCR_ISO;
PHY_WRITE(sc, MII_BMCR, reg);
/*
- Fix a typo in a comment. - Fix whitespace according to style(9). - Sync the comment describing why we have to wait in nsphy_reset() with nsphyter_reset(). It's true that the manual tells to not do a reset within 500us of applying power but that's unlikely the cause of problems seen here. Generally having to wait 500us after a reset however is.
2008-01-27 01:30:02 +00:00
* It is best to allow a little time for the reset to settle
* in before we start polling the BMCR again. Notably, the
* DP83840A manuals state that there should be a 500us delay
* between asserting software reset and attempting MII serial
* operations. Be conservative.
- Don't add IFM_NONE when used in combination with pcn(4) as for MII loopback to work PCnet chips additionally need to be placed into external loopback mode which pcn(4) doesn't do so far. - In nsphy_service() just use if_dname instead of determining the name of the parent NIC via device_get_name(device_get_parent(sc->mii_dev)). - Don't set MIIF_NOISOLATE, except for when used in combination with a NIC that wedges when isolating the PHYs, so nsphy(4) can be used in configurations with multiple PHYs. - Use mii_phy_add_media() instead of mii_add_media() so the latter can be eventually retired. - Take advantage of mii_phy_setmedia() (requires the MIIF_FORCEANEG added in sys/dev/mii/mii_physubr.c 1.26, sys/dev/mii/miivar.h 1.19). - Implement a separate nsphy_reset(). There are two reasons for this: 1) This PHY can take an inordinate amount of time to reset if media is attached; under fairly normal circumstances up to nearly one second. This is because it appears to go through an implicit auto- negotiation cycle as part of the reset. 2) During reset and auto-negotiation, the BMCR will clear the reset bit before the process is complete. It will return 0 until the process is complete and it's safe to access the PHY again. This is the first of two changes required to make the combination of Am79c971 and DP83840A found on certain HP cards and on-board in IBM machines work. - Fix some whitespace nits. Based on: NetBSD (except for the first and second item) MFC after: 2 weeks
2006-11-28 01:01:02 +00:00
*/
DELAY(1000);
/*
* Wait another 2s for it to complete.
* This is only a little overkill as under normal circumstances
* the PHY can take up to 1s to complete reset.
* This is also a bit odd because after a reset, the BMCR will
* clear the reset bit and simply reports 0 even though the reset
* is not yet complete.
*/
for (i = 0; i < 1000; i++) {
reg = PHY_READ(sc, MII_BMCR);
if (reg != 0 && (reg & BMCR_RESET) == 0)
break;
DELAY(2000);
}
if ((sc->mii_flags & MIIF_NOISOLATE) == 0) {
if ((ife == NULL && sc->mii_inst != 0) ||
(ife != NULL && IFM_INST(ife->ifm_media) != sc->mii_inst))
PHY_WRITE(sc, MII_BMCR, reg | BMCR_ISO);
}
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
}
Reference in New Issue Copy Permalink