freebsd-nq/sys/netinet/ip_fastfwd.c

618 lines
16 KiB
C
Raw Normal View History

/*-
* Copyright (c) 2003 Andre Oppermann, Internet Business Solutions AG
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote
* products derived from this software without specific prior written
* permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*/
/*
* ip_fastforward gets its speed from processing the forwarded packet to
* completion (if_output on the other side) without any queues or netisr's.
* The receiving interface DMAs the packet into memory, the upper half of
* driver calls ip_fastforward, we do our routing table lookup and directly
* send it off to the outgoing interface, which DMAs the packet to the
* network card. The only part of the packet we touch with the CPU is the
* IP header (unless there are complex firewall rules touching other parts
* of the packet, but that is up to you). We are essentially limited by bus
* bandwidth and how fast the network card/driver can set up receives and
* transmits.
*
* We handle basic errors, IP header errors, checksum errors,
* destination unreachable, fragmentation and fragmentation needed and
* report them via ICMP to the sender.
*
* Else if something is not pure IPv4 unicast forwarding we fall back to
* the normal ip_input processing path. We should only be called from
* interfaces connected to the outside world.
*
* Firewalling is fully supported including divert, ipfw fwd and ipfilter
* ipnat and address rewrite.
*
* IPSEC is not supported if this host is a tunnel broker. IPSEC is
* supported for connections to/from local host.
*
* We try to do the least expensive (in CPU ops) checks and operations
* first to catch junk with as little overhead as possible.
*
* We take full advantage of hardware support for IP checksum and
* fragmentation offloading.
*
* We don't do ICMP redirect in the fast forwarding path. I have had my own
* cases where two core routers with Zebra routing suite would send millions
* ICMP redirects to connected hosts if the destination router was not the
* default gateway. In one case it was filling the routing table of a host
* with approximately 300.000 cloned redirect entries until it ran out of
* kernel memory. However the networking code proved very robust and it didn't
* crash or fail in other ways.
*/
/*
* Many thanks to Matt Thomas of NetBSD for basic structure of ip_flow.c which
* is being followed here.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
#include "opt_ipfw.h"
#include "opt_ipstealth.h"
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/malloc.h>
#include <sys/mbuf.h>
#include <sys/protosw.h>
#include <sys/socket.h>
#include <sys/sysctl.h>
#include <net/pfil.h>
#include <net/if.h>
#include <net/if_types.h>
#include <net/if_var.h>
#include <net/if_dl.h>
#include <net/route.h>
#include <net/vnet.h>
#include <netinet/in.h>
#include <netinet/in_systm.h>
#include <netinet/in_var.h>
#include <netinet/ip.h>
#include <netinet/ip_var.h>
#include <netinet/ip_icmp.h>
#include <netinet/ip_options.h>
#include <machine/in_cksum.h>
static VNET_DEFINE(int, ipfastforward_active);
#define V_ipfastforward_active VNET(ipfastforward_active)
Build on Jeff Roberson's linker-set based dynamic per-CPU allocator (DPCPU), as suggested by Peter Wemm, and implement a new per-virtual network stack memory allocator. Modify vnet to use the allocator instead of monolithic global container structures (vinet, ...). This change solves many binary compatibility problems associated with VIMAGE, and restores ELF symbols for virtualized global variables. Each virtualized global variable exists as a "reference copy", and also once per virtual network stack. Virtualized global variables are tagged at compile-time, placing the in a special linker set, which is loaded into a contiguous region of kernel memory. Virtualized global variables in the base kernel are linked as normal, but those in modules are copied and relocated to a reserved portion of the kernel's vnet region with the help of a the kernel linker. Virtualized global variables exist in per-vnet memory set up when the network stack instance is created, and are initialized statically from the reference copy. Run-time access occurs via an accessor macro, which converts from the current vnet and requested symbol to a per-vnet address. When "options VIMAGE" is not compiled into the kernel, normal global ELF symbols will be used instead and indirection is avoided. This change restores static initialization for network stack global variables, restores support for non-global symbols and types, eliminates the need for many subsystem constructors, eliminates large per-subsystem structures that caused many binary compatibility issues both for monitoring applications (netstat) and kernel modules, removes the per-function INIT_VNET_*() macros throughout the stack, eliminates the need for vnet_symmap ksym(2) munging, and eliminates duplicate definitions of virtualized globals under VIMAGE_GLOBALS. Bump __FreeBSD_version and update UPDATING. Portions submitted by: bz Reviewed by: bz, zec Discussed with: gnn, jamie, jeff, jhb, julian, sam Suggested by: peter Approved by: re (kensmith)
2009-07-14 22:48:30 +00:00
SYSCTL_VNET_INT(_net_inet_ip, OID_AUTO, fastforwarding, CTLFLAG_RW,
&VNET_NAME(ipfastforward_active), 0, "Enable fast IP forwarding");
static struct sockaddr_in *
ip_findroute(struct route *ro, struct in_addr dest, struct mbuf *m)
{
struct sockaddr_in *dst;
struct rtentry *rt;
/*
* Find route to destination.
*/
bzero(ro, sizeof(*ro));
dst = (struct sockaddr_in *)&ro->ro_dst;
dst->sin_family = AF_INET;
dst->sin_len = sizeof(*dst);
dst->sin_addr.s_addr = dest.s_addr;
in_rtalloc_ign(ro, 0, M_GETFIB(m));
/*
* Route there and interface still up?
*/
rt = ro->ro_rt;
if (rt && (rt->rt_flags & RTF_UP) &&
(rt->rt_ifp->if_flags & IFF_UP) &&
(rt->rt_ifp->if_drv_flags & IFF_DRV_RUNNING)) {
if (rt->rt_flags & RTF_GATEWAY)
dst = (struct sockaddr_in *)rt->rt_gateway;
} else {
IPSTAT_INC(ips_noroute);
IPSTAT_INC(ips_cantforward);
if (rt)
RTFREE(rt);
icmp_error(m, ICMP_UNREACH, ICMP_UNREACH_HOST, 0, 0);
return NULL;
}
return dst;
}
/*
* Try to forward a packet based on the destination address.
* This is a fast path optimized for the plain forwarding case.
2009-09-06 07:29:22 +00:00
* If the packet is handled (and consumed) here then we return NULL;
* otherwise mbuf is returned and the packet should be delivered
* to ip_input for full processing.
*/
struct mbuf *
ip_fastforward(struct mbuf *m)
{
struct ip *ip;
struct mbuf *m0 = NULL;
struct route ro;
struct sockaddr_in *dst = NULL;
struct ifnet *ifp;
struct in_addr odest, dest;
u_short sum, ip_len;
int error = 0;
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
int hlen, mtu;
#ifdef IPFIREWALL_FORWARD
struct m_tag *fwd_tag;
#endif
/*
* Are we active and forwarding packets?
*/
if (!V_ipfastforward_active || !V_ipforwarding)
return m;
M_ASSERTVALID(m);
M_ASSERTPKTHDR(m);
bzero(&ro, sizeof(ro));
/*
* Step 1: check for packet drop conditions (and sanity checks)
*/
/*
* Is entire packet big enough?
*/
if (m->m_pkthdr.len < sizeof(struct ip)) {
IPSTAT_INC(ips_tooshort);
goto drop;
}
/*
* Is first mbuf large enough for ip header and is header present?
*/
if (m->m_len < sizeof (struct ip) &&
(m = m_pullup(m, sizeof (struct ip))) == NULL) {
IPSTAT_INC(ips_toosmall);
return NULL; /* mbuf already free'd */
}
ip = mtod(m, struct ip *);
/*
* Is it IPv4?
*/
if (ip->ip_v != IPVERSION) {
IPSTAT_INC(ips_badvers);
goto drop;
}
/*
* Is IP header length correct and is it in first mbuf?
*/
hlen = ip->ip_hl << 2;
if (hlen < sizeof(struct ip)) { /* minimum header length */
IPSTAT_INC(ips_badhlen);
goto drop;
}
if (hlen > m->m_len) {
if ((m = m_pullup(m, hlen)) == NULL) {
IPSTAT_INC(ips_badhlen);
return NULL; /* mbuf already free'd */
}
ip = mtod(m, struct ip *);
}
/*
* Checksum correct?
*/
if (m->m_pkthdr.csum_flags & CSUM_IP_CHECKED)
sum = !(m->m_pkthdr.csum_flags & CSUM_IP_VALID);
else {
if (hlen == sizeof(struct ip))
sum = in_cksum_hdr(ip);
else
sum = in_cksum(m, hlen);
}
if (sum) {
IPSTAT_INC(ips_badsum);
goto drop;
}
/*
* Remember that we have checked the IP header and found it valid.
*/
m->m_pkthdr.csum_flags |= (CSUM_IP_CHECKED | CSUM_IP_VALID);
ip_len = ntohs(ip->ip_len);
/*
* Is IP length longer than packet we have got?
*/
if (m->m_pkthdr.len < ip_len) {
IPSTAT_INC(ips_tooshort);
goto drop;
}
/*
* Is packet longer than IP header tells us? If yes, truncate packet.
*/
if (m->m_pkthdr.len > ip_len) {
if (m->m_len == m->m_pkthdr.len) {
m->m_len = ip_len;
m->m_pkthdr.len = ip_len;
} else
m_adj(m, ip_len - m->m_pkthdr.len);
}
/*
* Is packet from or to 127/8?
*/
if ((ntohl(ip->ip_dst.s_addr) >> IN_CLASSA_NSHIFT) == IN_LOOPBACKNET ||
(ntohl(ip->ip_src.s_addr) >> IN_CLASSA_NSHIFT) == IN_LOOPBACKNET) {
IPSTAT_INC(ips_badaddr);
goto drop;
}
#ifdef ALTQ
/*
* Is packet dropped by traffic conditioner?
*/
if (altq_input != NULL && (*altq_input)(m, AF_INET) == 0)
goto drop;
#endif
/*
* Step 2: fallback conditions to normal ip_input path processing
*/
/*
* Only IP packets without options
*/
if (ip->ip_hl != (sizeof(struct ip) >> 2)) {
if (ip_doopts == 1)
return m;
else if (ip_doopts == 2) {
icmp_error(m, ICMP_UNREACH, ICMP_UNREACH_FILTER_PROHIB,
0, 0);
return NULL; /* mbuf already free'd */
}
/* else ignore IP options and continue */
}
/*
* Only unicast IP, not from loopback, no L2 or IP broadcast,
* no multicast, no INADDR_ANY
*
* XXX: Probably some of these checks could be direct drop
* conditions. However it is not clear whether there are some
* hacks or obscure behaviours which make it neccessary to
* let ip_input handle it. We play safe here and let ip_input
* deal with it until it is proven that we can directly drop it.
*/
if ((m->m_flags & (M_BCAST|M_MCAST)) ||
(m->m_pkthdr.rcvif->if_flags & IFF_LOOPBACK) ||
ntohl(ip->ip_src.s_addr) == (u_long)INADDR_BROADCAST ||
ntohl(ip->ip_dst.s_addr) == (u_long)INADDR_BROADCAST ||
IN_MULTICAST(ntohl(ip->ip_src.s_addr)) ||
IN_MULTICAST(ntohl(ip->ip_dst.s_addr)) ||
IN_LINKLOCAL(ntohl(ip->ip_src.s_addr)) ||
IN_LINKLOCAL(ntohl(ip->ip_dst.s_addr)) ||
ip->ip_src.s_addr == INADDR_ANY ||
ip->ip_dst.s_addr == INADDR_ANY )
return m;
/*
* Is it for a local address on this host?
*/
if (in_localip(ip->ip_dst))
return m;
IPSTAT_INC(ips_total);
/*
* Step 3: incoming packet firewall processing
*/
/*
* Convert to host representation
*/
ip->ip_len = ntohs(ip->ip_len);
ip->ip_off = ntohs(ip->ip_off);
odest.s_addr = dest.s_addr = ip->ip_dst.s_addr;
/*
* Run through list of ipfilter hooks for input packets
*/
if (!PFIL_HOOKED(&V_inet_pfil_hook))
goto passin;
if (pfil_run_hooks(
&V_inet_pfil_hook, &m, m->m_pkthdr.rcvif, PFIL_IN, NULL) ||
m == NULL)
goto drop;
M_ASSERTVALID(m);
M_ASSERTPKTHDR(m);
ip = mtod(m, struct ip *); /* m may have changed by pfil hook */
dest.s_addr = ip->ip_dst.s_addr;
/*
* Destination address changed?
*/
if (odest.s_addr != dest.s_addr) {
/*
* Is it now for a local address on this host?
*/
if (in_localip(dest))
goto forwardlocal;
/*
* Go on with new destination address
*/
}
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
#ifdef IPFIREWALL_FORWARD
if (m->m_flags & M_FASTFWD_OURS) {
/*
* ipfw changed it for a local address on this host.
*/
goto forwardlocal;
}
#endif /* IPFIREWALL_FORWARD */
passin:
/*
* Step 4: decrement TTL and look up route
*/
/*
* Check TTL
*/
#ifdef IPSTEALTH
if (!V_ipstealth) {
#endif
if (ip->ip_ttl <= IPTTLDEC) {
icmp_error(m, ICMP_TIMXCEED, ICMP_TIMXCEED_INTRANS, 0, 0);
return NULL; /* mbuf already free'd */
}
/*
* Decrement the TTL and incrementally change the IP header checksum.
* Don't bother doing this with hw checksum offloading, it's faster
* doing it right here.
*/
ip->ip_ttl -= IPTTLDEC;
if (ip->ip_sum >= (u_int16_t) ~htons(IPTTLDEC << 8))
ip->ip_sum -= ~htons(IPTTLDEC << 8);
else
ip->ip_sum += htons(IPTTLDEC << 8);
#ifdef IPSTEALTH
}
#endif
/*
* Find route to destination.
*/
if ((dst = ip_findroute(&ro, dest, m)) == NULL)
return NULL; /* icmp unreach already sent */
ifp = ro.ro_rt->rt_ifp;
/*
* Immediately drop blackholed traffic, and directed broadcasts
* for either the all-ones or all-zero subnet addresses on
* locally attached networks.
*/
if ((ro.ro_rt->rt_flags & (RTF_BLACKHOLE|RTF_BROADCAST)) != 0)
goto drop;
/*
* Step 5: outgoing firewall packet processing
*/
/*
* Run through list of hooks for output packets.
*/
if (!PFIL_HOOKED(&V_inet_pfil_hook))
goto passout;
if (pfil_run_hooks(&V_inet_pfil_hook, &m, ifp, PFIL_OUT, NULL) || m == NULL) {
goto drop;
}
M_ASSERTVALID(m);
M_ASSERTPKTHDR(m);
ip = mtod(m, struct ip *);
dest.s_addr = ip->ip_dst.s_addr;
/*
* Destination address changed?
*/
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
#ifndef IPFIREWALL_FORWARD
if (odest.s_addr != dest.s_addr) {
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
#else
fwd_tag = m_tag_find(m, PACKET_TAG_IPFORWARD, NULL);
if (odest.s_addr != dest.s_addr || fwd_tag != NULL) {
#endif /* IPFIREWALL_FORWARD */
/*
* Is it now for a local address on this host?
*/
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
#ifndef IPFIREWALL_FORWARD
if (in_localip(dest)) {
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
#else
if (m->m_flags & M_FASTFWD_OURS || in_localip(dest)) {
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
#endif /* IPFIREWALL_FORWARD */
forwardlocal:
/*
* Return packet for processing by ip_input().
* Keep host byte order as expected at ip_input's
* "ours"-label.
*/
m->m_flags |= M_FASTFWD_OURS;
if (ro.ro_rt)
RTFREE(ro.ro_rt);
return m;
}
/*
* Redo route lookup with new destination address
*/
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
#ifdef IPFIREWALL_FORWARD
if (fwd_tag) {
dest.s_addr = ((struct sockaddr_in *)
(fwd_tag + 1))->sin_addr.s_addr;
Convert ipfw to use PFIL_HOOKS. This is change is transparent to userland and preserves the ipfw ABI. The ipfw core packet inspection and filtering functions have not been changed, only how ipfw is invoked is different. However there are many changes how ipfw is and its add-on's are handled: In general ipfw is now called through the PFIL_HOOKS and most associated magic, that was in ip_input() or ip_output() previously, is now done in ipfw_check_[in|out]() in the ipfw PFIL handler. IPDIVERT is entirely handled within the ipfw PFIL handlers. A packet to be diverted is checked if it is fragmented, if yes, ip_reass() gets in for reassembly. If not, or all fragments arrived and the packet is complete, divert_packet is called directly. For 'tee' no reassembly attempt is made and a copy of the packet is sent to the divert socket unmodified. The original packet continues its way through ip_input/output(). ipfw 'forward' is done via m_tag's. The ipfw PFIL handlers tag the packet with the new destination sockaddr_in. A check if the new destination is a local IP address is made and the m_flags are set appropriately. ip_input() and ip_output() have some more work to do here. For ip_input() the m_flags are checked and a packet for us is directly sent to the 'ours' section for further processing. Destination changes on the input path are only tagged and the 'srcrt' flag to ip_forward() is set to disable destination checks and ICMP replies at this stage. The tag is going to be handled on output. ip_output() again checks for m_flags and the 'ours' tag. If found, the packet will be dropped back to the IP netisr where it is going to be picked up by ip_input() again and the directly sent to the 'ours' section. When only the destination changes, the route's 'dst' is overwritten with the new destination from the forward m_tag. Then it jumps back at the route lookup again and skips the firewall check because it has been marked with M_SKIP_FIREWALL. ipfw 'forward' has to be compiled into the kernel with 'option IPFIREWALL_FORWARD' to enable it. DUMMYNET is entirely handled within the ipfw PFIL handlers. A packet for a dummynet pipe or queue is directly sent to dummynet_io(). Dummynet will then inject it back into ip_input/ip_output() after it has served its time. Dummynet packets are tagged and will continue from the next rule when they hit the ipfw PFIL handlers again after re-injection. BRIDGING and IPFW_ETHER are not changed yet and use ipfw_chk() directly as they did before. Later this will be changed to dedicated ETHER PFIL_HOOKS. More detailed changes to the code: conf/files Add netinet/ip_fw_pfil.c. conf/options Add IPFIREWALL_FORWARD option. modules/ipfw/Makefile Add ip_fw_pfil.c. net/bridge.c Disable PFIL_HOOKS if ipfw for bridging is active. Bridging ipfw is still directly invoked to handle layer2 headers and packets would get a double ipfw when run through PFIL_HOOKS as well. netinet/ip_divert.c Removed divert_clone() function. It is no longer used. netinet/ip_dummynet.[ch] Neither the route 'ro' nor the destination 'dst' need to be stored while in dummynet transit. Structure members and associated macros are removed. netinet/ip_fastfwd.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_fw.h Removed 'ro' and 'dst' from struct ip_fw_args. netinet/ip_fw2.c (Re)moved some global variables and the module handling. netinet/ip_fw_pfil.c New file containing the ipfw PFIL handlers and module initialization. netinet/ip_input.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. ip_forward() does not longer require the 'next_hop' struct sockaddr_in argument. Disable early checks if 'srcrt' is set. netinet/ip_output.c Removed all direct ipfw handling code and replace it with the new 'ipfw forward' handling code. netinet/ip_var.h Add ip_reass() as general function. (Used from ipfw PFIL handlers for IPDIVERT.) netinet/raw_ip.c Directly check if ipfw and dummynet control pointers are active. netinet/tcp_input.c Rework the 'ipfw forward' to local code to work with the new way of forward tags. netinet/tcp_sack.c Remove include 'opt_ipfw.h' which is not needed here. sys/mbuf.h Remove m_claim_next() macro which was exclusively for ipfw 'forward' and is no longer needed. Approved by: re (scottl)
2004-08-17 22:05:54 +00:00
m_tag_delete(m, fwd_tag);
}
#endif /* IPFIREWALL_FORWARD */
RTFREE(ro.ro_rt);
if ((dst = ip_findroute(&ro, dest, m)) == NULL)
return NULL; /* icmp unreach already sent */
ifp = ro.ro_rt->rt_ifp;
}
passout:
/*
* Step 6: send off the packet
*/
/*
* Check if route is dampned (when ARP is unable to resolve)
*/
if ((ro.ro_rt->rt_flags & RTF_REJECT) &&
(ro.ro_rt->rt_rmx.rmx_expire == 0 ||
time_uptime < ro.ro_rt->rt_rmx.rmx_expire)) {
icmp_error(m, ICMP_UNREACH, ICMP_UNREACH_HOST, 0, 0);
goto consumed;
}
#ifndef ALTQ
/*
* Check if there is enough space in the interface queue
*/
if ((ifp->if_snd.ifq_len + ip->ip_len / ifp->if_mtu + 1) >=
ifp->if_snd.ifq_maxlen) {
IPSTAT_INC(ips_odropped);
/* would send source quench here but that is depreciated */
goto drop;
}
#endif
/*
* Check if media link state of interface is not down
*/
if (ifp->if_link_state == LINK_STATE_DOWN) {
icmp_error(m, ICMP_UNREACH, ICMP_UNREACH_HOST, 0, 0);
goto consumed;
}
/*
* Check if packet fits MTU or if hardware will fragment for us
*/
if (ro.ro_rt->rt_rmx.rmx_mtu)
mtu = min(ro.ro_rt->rt_rmx.rmx_mtu, ifp->if_mtu);
else
mtu = ifp->if_mtu;
if (ip->ip_len <= mtu ||
(ifp->if_hwassist & CSUM_FRAGMENT && (ip->ip_off & IP_DF) == 0)) {
/*
* Restore packet header fields to original values
*/
ip->ip_len = htons(ip->ip_len);
ip->ip_off = htons(ip->ip_off);
/*
* Send off the packet via outgoing interface
*/
error = (*ifp->if_output)(ifp, m,
(struct sockaddr *)dst, &ro);
} else {
/*
* Handle EMSGSIZE with icmp reply needfrag for TCP MTU discovery
*/
if (ip->ip_off & IP_DF) {
IPSTAT_INC(ips_cantfrag);
icmp_error(m, ICMP_UNREACH, ICMP_UNREACH_NEEDFRAG,
0, mtu);
goto consumed;
} else {
/*
* We have to fragment the packet
*/
m->m_pkthdr.csum_flags |= CSUM_IP;
/*
* ip_fragment expects ip_len and ip_off in host byte
* order but returns all packets in network byte order
*/
if (ip_fragment(ip, &m, mtu, ifp->if_hwassist,
(~ifp->if_hwassist & CSUM_DELAY_IP))) {
goto drop;
}
KASSERT(m != NULL, ("null mbuf and no error"));
/*
* Send off the fragments via outgoing interface
*/
error = 0;
do {
m0 = m->m_nextpkt;
m->m_nextpkt = NULL;
error = (*ifp->if_output)(ifp, m,
(struct sockaddr *)dst, &ro);
if (error)
break;
} while ((m = m0) != NULL);
if (error) {
/* Reclaim remaining fragments */
for (m = m0; m; m = m0) {
m0 = m->m_nextpkt;
m_freem(m);
}
} else
IPSTAT_INC(ips_fragmented);
}
}
if (error != 0)
IPSTAT_INC(ips_odropped);
else {
ro.ro_rt->rt_rmx.rmx_pksent++;
IPSTAT_INC(ips_forward);
IPSTAT_INC(ips_fastforward);
}
consumed:
RTFREE(ro.ro_rt);
return NULL;
drop:
if (m)
m_freem(m);
if (ro.ro_rt)
RTFREE(ro.ro_rt);
return NULL;
}