freebsd-nq/share/misc/scsi_modes

359 lines
8.3 KiB
Plaintext
Raw Normal View History

1995-04-28 19:25:17 +00:00
# SCSI mode page data base.
# Copyright (c) 1995 HD Associates
# Copyright (c) 2001 The FreeBSD Project
1995-04-28 19:25:17 +00:00
# (contact: dufault@hda.com)
# All rights reserved.
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions
# are met:
# 1. Redistributions of source code must retain the above copyright
# notice, this list of conditions and the following disclaimer.
# 2. Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in the
# documentation and/or other materials provided with the distribution.
# 3. The name of HD Associates
# may not be used to endorse or promote products derived from this software
# without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY HD ASSOCIATES ``AS IS'' AND
# ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
# ARE DISCLAIMED. IN NO EVENT SHALL HD ASSOCIATES BE LIABLE
# FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
# DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
# OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
# HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
# OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
# SUCH DAMAGE.
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
#
# $FreeBSD$
#
1995-04-28 19:25:17 +00:00
# The ordering is alphabetical by page name, as it appears in the SCSI spec.
# 'i' is a byte-sized integral types, followed by a field width of
# 1 through 4 (1 to 4 bytes).
#
# 'b' is a bit-sized integral type
# 't' is a bitfield type- followed by a bit field width
#
# 'c' values are character arrays
# 'z' values are null-padded strings
#
#
# '*' suppresses assignment (for 'seeking').
# Bitfields are MSB to LSB.
1995-04-28 19:25:17 +00:00
# ALL DEVICE TYPES
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x0a "Control Mode Page" {
{Reserved} *t7
{RLEC} t1
{Queue Algorithm Modifier} t4
{Reserved} *t2
{QErr} t1
{DQue} t1
{EECA} t1
{Reserved} *t4
{RAENP} t1
{UAAENP} t1
{EAENP} t1
1995-04-28 19:25:17 +00:00
{Reserved} *i1
{Ready AEN Holdoff Period} i2
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x02 "Disconnect-Reconnect Page" {
1995-04-28 19:25:17 +00:00
{Buffer Full Ratio} i1
{Buffer Empty Ratio} i1
{Bus Inactivity Limit} i2
{Disconnect Time Limit} i2
{Connect Time Limit} i2
{Maximum Burst Size} i2
{Reserved} *t6
{DTDC} t2
1995-04-28 19:25:17 +00:00
{Reserved} *i1
{Reserved} *i1
{Reserved} *i1
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x09 "Peripheral Device Page" {
1995-04-28 19:25:17 +00:00
{Interface Identifier} i2
{Reserved} *i1
{Reserved} *i1
{Reserved} *i1
{Reserved} *i1
}
0x1a "Power Control" {
{Reserved} *i1
{Reserved} *t6
{Idle} t1
{Standby} t1
{Idle Condition Timer} i4
{Standby Condition Timer} i4
}
1995-04-28 19:25:17 +00:00
# DIRECT ACCESS DEVICES
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x08 "Caching Page" {
{IC} t1
{ABPF} t1
{CAP} t1
{DISC} t1
{SIZE} t1
{WCE} t1
{MF} t1
{RCD} t1
{Demand Retention Priority} t4
{Write Retention Priority} t4
1995-04-28 19:25:17 +00:00
{Disable Pre-fetch Transfer Length} i2
1996-08-21 22:38:20 +00:00
{Minimum Pre-fetch} i2
1995-04-28 19:25:17 +00:00
{Maximum Pre-fetch} i2
{Maximum Pre-fetch Ceiling} i2
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x05 "Flexible Disk Page" {
1995-04-28 19:25:17 +00:00
{Transfer rate} i2
{Number of heads} i1
{Sectors per track} i1
{Data bytes per sector} i2
{Number of cylinders} i2
{Starting cylinder-write precompensation} i2
{Starting cylinder-reduced write current} i2
{Drive step rate} i2
{Drive step pulse width} i1
{Head settle delay} i2
{Motor on delay} i1
{Motor off delay} i1
{TRDY} t1
{SSN} t1
{MO} t1
{Reserved} *t5
{Reserved} *t4
{SPC} t4
1995-04-28 19:25:17 +00:00
{Write Compensation} i1
{Head load delay} i1
{Head unload delay} i1
{Pin 34} t4
{Pin 2} t4
{Pin 4} t4
{Pin 1} t4
1995-04-28 19:25:17 +00:00
{Medium rotation rate} i2
{Reserved} *i1
{Reserved} *i1
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x03 "Format Device Page" {
1995-04-28 19:25:17 +00:00
{Tracks per Zone} i2
{Alternate Sectors per Zone} i2
{Alternate Tracks per Zone} i2
{Alternate Tracks per Logical Unit} i2
{Sectors per Track} i2
{Data Bytes per Physical Sector} i2
{Interleave} i2
{Track Skew Factor} i2
{Cylinder Skew Factor} i2
{SSEC} t1
{HSEC} t1
{RMB} t1
{SURF} t1
{Reserved} *t4
1995-04-28 19:25:17 +00:00
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x0b "Medium Types Supported Page" {
1995-04-28 19:25:17 +00:00
{Reserved} *i1
{Reserved} *i1
{Medium type one supported} i1
{Medium type two supported} i1
{Medium type three supported} i1
{Medium type four supported} i1
}
# Notch page (0x0c)
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x0c "Notch and Partition Page";
1995-04-28 19:25:17 +00:00
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x01 "Read-Write Error Recovery Page" {
{AWRE (Auto Write Reallocation Enbld)} t1
{ARRE (Auto Read Reallocation Enbld)} t1
{TB (Transfer Block)} t1
{RC (Read Continuous)} t1
{EER (Enable Early Recovery)} t1
{PER (Post Error)} t1
{DTE (Disable Transfer on Error)} t1
{DCR (Disable Correction)} t1
1995-04-28 19:25:17 +00:00
{Read Retry Count} i1
{Correction Span} i1
{Head Offset Count} i1
{Data Strobe Offset Count} i1
{Reserved} *i1
{Write Retry Count} i1
{Reserved} *i1
{Recovery Time Limit} i2
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x04 "Rigid Disk Drive Geometry Page" {
1995-04-28 19:25:17 +00:00
{Number of Cylinders} i3
{Number of Heads} i1
{Starting Cylinder-Write Precompensation} i3
{Starting Cylinder-Reduced Write Current} i3
{Drive Step Rate} i2
{Landing Zone Cylinder} i3
{Reserved} *t6
{RPL} t2
1995-04-28 19:25:17 +00:00
{Rotational Offset} i1
{Reserved} *i1
{Medium Rotation Rate} i2
{Reserved} *i1
{Reserved} *i1
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x07 "Verify Error Recovery Page" {
{Reserved} *t4
{EER} t1
{PER} t1
{DTE} t1
{DCR} t1
1995-04-28 19:25:17 +00:00
{Verify Retry Count} i1
{Verify Correction Span} i1
{Reserved} *i1
{Reserved} *i1
{Reserved} *i1
{Reserved} *i1
{Reserved} *i1
{Verify Recovery Time Limit} i2
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x0E "CD-ROM Audio Control Parameters Page" {
{Reserved} *t5
{Immed} t1
{SOTC} t1
{Reserved} *t1
{Reserved} *i2
{APRVal} t1
{Reserved} *t3
{Format of LBAs / sec.} t4
{Logical Blocks per Second of Audio Playback} i2
{Reserved} *t4
{Output Port 0 Channel Selection} t4
{Output Port 0 Volume} i1
{Reserved} *t4
{Output Port 1 Channel Selection} t4
{Output Port 1 Volume} i1
{Reserved} *t4
{Output Port 2 Channel Selection} t4
{Output Port 2 Volume} i1
{Reserved} *t4
{Output Port 3 Channel Selection} t4
{Output Port 3 Volume} i1
}
# SEQUENTIAL ACCESS DEVICES
0x10 "Device Configuration Page" {
{Reserved} *t1
{Change Active Partition} t1
{Change Active Format} t1
{Active Format} t5
{Active Partition} i1
{Write Buffer Full Ratio} i1
{Write Buffer Empty Ratio} i1
{Write Delay Time} i2
{Data Buffer Recovery} t1
{Block Identifiers Support} t1
{Report Setmarks} t1
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
{Automatic Velocity Control} t1
{Stop on Consecutive Filemarks} t2
{Recover Buffer Order} t1
{Report Early-Warning} t1
{Gap Size} i1
{EOD Defined} t3
{Enable EOD Generation} t1
{Synchronize at Early-Warning} t1
{Reserved} *t3
{Buffer Size at Early-Warning} i3
{Select Data Compression Algorithm} i1
{Reserved} *t5
{SCSI-3 Associated Write Protect} t1
{SCSI-3 Persistent Write Protect} t1
{SCSI-3 Permanent Write Protect} t1
}
0x0f "Data Compression Page" {
{Data Compression Enabled} t1
{Date Compression Capable} t1
{Reserved} *t6
{Data Decompression Capable} t1
{Data Decompression Report on Exception} t2
{Reserved} *t5
{Compression Algorithm} i4
{Decompression Algorithm} i4
{Reserved} *i4
}
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
# Removable devices
0x1b "Removable Block Access Capacities Page" {
{System Floppy Type Device} t1
{Supports Reporting Format Progress} t1
{Reserved} *t6
{Non CD Optical Device} t1
{Single or Multiple LUN Supported} t1
{Reserved} *t3
{Total Logical Units Supported} t3
{Reserved} *i8
}
# CD-ROM (and CD-R[W]) devices
0x2a "CD capabilities and mechanical status page" {
{Reserved} *t4
{Method 2} t1
{CD-RW Read} t1
{CD-R Read} t1
{Reserved} *t4
{Test Write} t1
{CD-RW Write} t1
{CD-R Write} t1
{Reserved} *t1
{Multi Session} t1
{Mode 2 Form 2} t1
{Mode 2 Form 1} t1
{Digital Port (2)} t1
{Digital Port (1)} t1
{Composite} t1
{Audio Play} t1
{Read Bar Code} t1
{UPC} t1
{ISRC} t1
{C2 Pointers are supported} t1
{R-W De-interleaved & corrected} t1
{R-W Supported} t1
{CD-DA Stream is Accurate} t1
{CD-DA Commands Supported} t1
{Loading Mechanism Type} t3
{Reserved} *t1
{Eject} t1
{Prevent Jumper} t1
{Lock State} t1
{Lock} t1
{Reserved} *t4
{S/W Slot Selection} t1
{Changer Supports Disc Present reporting} t1
{Separate Channel Mute Supported} t1
{Separate volume levels per channel} t1
{Maximum Read Speed Supported (kBps)} i2
{Number of Volume Leves Supported} i2
{Buffer Size supported by Drive (KB)} i2
{Current Read Speed Selected (kBps)} i2
{Reserved} *i1
{Reserved} *t2
{Length} t2
{LSBF} t1
{RCK} t1
{BCK} t1
{Reserved} *t1
{Maximum Write Speed Supported (kBps)} i2
{Current Write Speed Supported (kBps)} i2
};
This is an overhaul of the mode page handling in camcontrol as well as related patches. These include: * Mode page editting can be scripted. This involves two things: first, if stdin is not a tty, changes are read from stdin rather than invoking $EDITOR. Second, and more importantly, not all modepage entries must be included in the change set. This means that camcontrol can now gracefully handle more intrusive editting from the $EDITOR, including removal or rearrangement of lines. It also means that you can do stuff like: # echo "WCE: 1" | camcontrol modepage da3 -m 8 -e # newfs /dev/da3 # echo "WCE: 0" | camcontrol modepage da3 -m 8 -e * Range-checking on user-supplied input values. modeedit.c now uses the field width specifiers to determine the maximum allowable value for a field. If the user enters a value larger than the maximum, it clips the value to the max and warns the user. This also involved patching cam_cmdparse.c to be more consistent with regards to the "count" parameter to arg_put (previously is was the length of strings and 1 for all integral types). The cam_cdbparse(3) man page was also updated to reflect the revised semantics. * In the process, I removed the 64 entry limit on mode pages (not that we were even close to hitting that limit). This was a nice side-effect of the other changes. * Technically, the new mode editting functionality allows editting of character array entries in mode pages (type 'c' or 'z'), however since buff_encode doesn't grok them it is currently useless. * Camcontrol gained two new options related to mode pages: -l and -b. The former lists all available mode pages for a given device. The latter forces mode page display in binary format (the default when no mode page definition was found in scsi_modes). * Added support for mode page names to scsi_modes. Allows names to be displayed alongside mode numbers in the mode page listing. Updated scsi_modes to use the new functionality. This also adds the semicolon into the scsi_modes syntax as an optional mode page definition terminator. This is needed to name pages without providing a page format definition. * Updated scsi_all.h to include a structure describing mode page headers. * Added $FreeBSD$ line to scsi_modes. Inspired by: dwhite Reviewed by: ken
2000-08-08 06:24:17 +00:00
0x00 "Vendor-Specific";