freebsd-nq/sys/dev/mii/exphy.c

314 lines
8.7 KiB
C
Raw Normal View History

This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/* $NetBSD: exphy.c,v 1.16 1999/04/23 04:24:32 thorpej Exp $ */
/*-
* Copyright (c) 1998, 1999 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
* NASA Ames Research Center, and by Frank van der Linden.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by the NetBSD
* Foundation, Inc. and its contributors.
* 4. Neither the name of The NetBSD Foundation nor the names of its
* contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
/*
* Copyright (c) 1997 Manuel Bouyer. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Manuel Bouyer.
* 4. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
* driver for 3Com internal PHYs
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/module.h>
#include <sys/bus.h>
#include <net/if.h>
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
#include <dev/mii/miidevs.h>
#include "miibus_if.h"
#if !defined(lint)
static const char rcsid[] =
"$FreeBSD$";
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
#endif
2002-03-20 02:08:01 +00:00
static int exphy_probe (device_t);
static int exphy_attach (device_t);
static int exphy_detach (device_t);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
static device_method_t exphy_methods[] = {
/* device interface */
DEVMETHOD(device_probe, exphy_probe),
DEVMETHOD(device_attach, exphy_attach),
DEVMETHOD(device_detach, exphy_detach),
DEVMETHOD(device_shutdown, bus_generic_shutdown),
{ 0, 0 }
};
static devclass_t exphy_devclass;
static driver_t exphy_driver = {
"xlphy",
exphy_methods,
sizeof(struct mii_softc)
};
DRIVER_MODULE(xlphy, miibus, exphy_driver, exphy_devclass, 0, 0);
2002-03-20 02:08:01 +00:00
static int exphy_service(struct mii_softc *, struct mii_data *, int);
static void exphy_reset(struct mii_softc *);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
static int exphy_probe(dev)
device_t dev;
{
struct mii_attach_args *ma;
device_t parent;
ma = device_get_ivars(dev);
parent = device_get_parent(device_get_parent(dev));
/*
* Argh, 3Com PHY reports oui == 0 model == 0!
*/
if ((MII_OUI(ma->mii_id1, ma->mii_id2) != 0 ||
MII_MODEL(ma->mii_id2) != 0) &&
(MII_OUI(ma->mii_id1, ma->mii_id2) != MII_OUI_BROADCOM ||
MII_MODEL(ma->mii_id2) != MII_MODEL_BROADCOM_3c905Cphy))
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (ENXIO);
/*
* Make sure the parent is an `ex'.
*/
if (strcmp(device_get_name(parent), "xl") != 0)
return (ENXIO);
if (MII_OUI(ma->mii_id1, ma->mii_id2) == 0)
device_set_desc(dev, "3Com internal media interface");
else
device_set_desc(dev, MII_STR_BROADCOM_3c905Cphy);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
}
static int exphy_attach(dev)
device_t dev;
{
struct mii_softc *sc;
struct mii_attach_args *ma;
struct mii_data *mii;
sc = device_get_softc(dev);
ma = device_get_ivars(dev);
sc->mii_dev = device_get_parent(dev);
mii = device_get_softc(sc->mii_dev);
/*
* The 3Com PHY can never be isolated, so never allow non-zero
* instances!
*/
if (mii->mii_instance != 0) {
device_printf(dev, "ignoring this PHY, non-zero instance\n");
return(ENXIO);
}
LIST_INSERT_HEAD(&mii->mii_phys, sc, mii_list);
sc->mii_inst = mii->mii_instance;
sc->mii_phy = ma->mii_phyno;
sc->mii_service = exphy_service;
sc->mii_pdata = mii;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
mii->mii_instance++;
sc->mii_flags |= MIIF_NOISOLATE;
#define ADD(m, c) ifmedia_add(&mii->mii_media, (m), (c), NULL)
#if 0 /* See above. */
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_NONE, 0, sc->mii_inst),
BMCR_ISO);
#endif
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_100_TX, IFM_LOOP, sc->mii_inst),
BMCR_LOOP|BMCR_S100);
exphy_reset(sc);
sc->mii_capabilities =
PHY_READ(sc, MII_BMSR) & ma->mii_capmask;
device_printf(dev, " ");
if ((sc->mii_capabilities & BMSR_MEDIAMASK) == 0)
printf("no media present");
else
mii_add_media(mii, sc->mii_capabilities,
sc->mii_inst);
printf("\n");
#undef ADD
MIIBUS_MEDIAINIT(sc->mii_dev);
return(0);
}
static int exphy_detach(dev)
device_t dev;
{
struct mii_softc *sc;
struct mii_data *mii;
sc = device_get_softc(dev);
mii = device_get_softc(device_get_parent(dev));
mii_phy_auto_stop(sc);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
sc->mii_dev = NULL;
LIST_REMOVE(sc, mii_list);
return(0);
}
static int
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
exphy_service(sc, mii, cmd)
struct mii_softc *sc;
struct mii_data *mii;
int cmd;
{
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
/*
* We can't isolate the 3Com PHY, so it has to be the only one!
*/
if (IFM_INST(ife->ifm_media) != sc->mii_inst)
panic("exphy_service: can't isolate 3Com PHY");
switch (cmd) {
case MII_POLLSTAT:
break;
case MII_MEDIACHG:
/*
* If the interface is not up, don't do anything.
*/
if ((mii->mii_ifp->if_flags & IFF_UP) == 0)
break;
switch (IFM_SUBTYPE(ife->ifm_media)) {
case IFM_AUTO:
/*
* If we're already in auto mode, just return.
*/
if (PHY_READ(sc, MII_BMCR) & BMCR_AUTOEN)
return (0);
(void) mii_phy_auto(sc, 1);
break;
case IFM_100_T4:
/*
* XXX Not supported as a manual setting right now.
*/
return (EINVAL);
default:
/*
* BMCR data is stored in the ifmedia entry.
*/
PHY_WRITE(sc, MII_ANAR,
mii_anar(ife->ifm_media));
PHY_WRITE(sc, MII_BMCR, ife->ifm_data);
}
break;
case MII_TICK:
/*
* Is the interface even up?
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
*/
if ((mii->mii_ifp->if_flags & IFF_UP) == 0)
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
/*
* Only used for autonegotiation.
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
*/
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO)
break;
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
/*
* The 3Com PHY's autonegotiation doesn't need to be
* kicked; it continues in the background.
*/
break;
}
/* Update the media status. */
ukphy_status(sc);
/* Callback if something changed. */
mii_phy_update(sc, cmd);
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
return (0);
}
static void
This commit adds support for the NetBSD MII abstraction layer and MII-compliant PHY drivers. Many 10/100 ethernet NICs available today either use an MII transceiver or have built-in transceivers that can be programmed using an MII interface. It makes sense then to separate this support out into common code instead of duplicating it in all of the NIC drivers. The mii code also handles all of the media detection, selection and reporting via the ifmedia interface. This is basically the same code from NetBSD's /sys/dev/mii, except it's been adapted to FreeBSD's bus architecture. The advantage to this is that it automatically allows everything to be turned into a loadable module. There are some common functions for use in drivers once an miibus has been attached (mii_mediachg(), mii_pollstat(), mii_tick()) as well as individual PHY drivers. There is also a generic driver for all PHYs that aren't handled by a specific driver. It's possible to do this because all 10/100 PHYs implement the same general register set in addition to their vendor-specific register sets, so for the most part you can use one driver for pretty much any PHY. There are a couple of oddball exceptions though, hence the need to have specific drivers. There are two layers: the generic "miibus" layer and the PHY driver layer. The drivers are child devices of "miibus" and the "miibus" is a child of a given NIC driver. The "miibus" code and the PHY drivers can actually be compiled and kldoaded as completely separate modules or compiled together into one module. For the moment I'm using the latter approach since the code is relatively small. Currently there are only three PHY drivers here: the generic driver, the built-in 3Com XL driver and the NS DP83840 driver. I'll be adding others later as I convert various NIC drivers to use this code. I realize that I'm cvs adding this stuff instead of importing it onto a separate vendor branch, but in my opinion the import approach doesn't really offer any significant advantage: I'm going to be maintaining this stuff and writing my own PHY drivers one way or the other.
1999-08-21 17:40:53 +00:00
exphy_reset(sc)
struct mii_softc *sc;
{
mii_phy_reset(sc);
/*
* XXX 3Com PHY doesn't set the BMCR properly after
* XXX reset, which breaks autonegotiation.
*/
PHY_WRITE(sc, MII_BMCR, BMCR_S100|BMCR_AUTOEN|BMCR_FDX);
}