freebsd-nq/sys/dev/e1000/e1000_ich8lan.h

/******************************************************************************

  Copyright (c) 2001-2010, Intel Corporation 
  All rights reserved.
  
  Redistribution and use in source and binary forms, with or without 
  modification, are permitted provided that the following conditions are met:
  
   1. Redistributions of source code must retain the above copyright notice, 
      this list of conditions and the following disclaimer.
  
   2. Redistributions in binary form must reproduce the above copyright 
      notice, this list of conditions and the following disclaimer in the 
      documentation and/or other materials provided with the distribution.
  
   3. Neither the name of the Intel Corporation nor the names of its 
      contributors may be used to endorse or promote products derived from 
      this software without specific prior written permission.
  
  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 
  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 
  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 
  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 
  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 
  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 
  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 
  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 
  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
  POSSIBILITY OF SUCH DAMAGE.

******************************************************************************/
/*$FreeBSD$*/

#ifndef _E1000_ICH8LAN_H_
#define _E1000_ICH8LAN_H_

#define ICH_FLASH_GFPREG                 0x0000
#define ICH_FLASH_HSFSTS                 0x0004
#define ICH_FLASH_HSFCTL                 0x0006
#define ICH_FLASH_FADDR                  0x0008
#define ICH_FLASH_FDATA0                 0x0010

/* Requires up to 10 seconds when MNG might be accessing part. */
#define ICH_FLASH_READ_COMMAND_TIMEOUT   10000000
#define ICH_FLASH_WRITE_COMMAND_TIMEOUT  10000000
#define ICH_FLASH_ERASE_COMMAND_TIMEOUT  10000000
#define ICH_FLASH_LINEAR_ADDR_MASK       0x00FFFFFF
#define ICH_FLASH_CYCLE_REPEAT_COUNT     10

#define ICH_CYCLE_READ                   0
#define ICH_CYCLE_WRITE                  2
#define ICH_CYCLE_ERASE                  3

#define FLASH_GFPREG_BASE_MASK           0x1FFF
#define FLASH_SECTOR_ADDR_SHIFT          12

#define ICH_FLASH_SEG_SIZE_256           256
#define ICH_FLASH_SEG_SIZE_4K            4096
#define ICH_FLASH_SEG_SIZE_8K            8192
#define ICH_FLASH_SEG_SIZE_64K           65536
#define ICH_FLASH_SECTOR_SIZE            4096

#define ICH_FLASH_REG_MAPSIZE            0x00A0

#define E1000_ICH_FWSM_RSPCIPHY          0x00000040 /* Reset PHY on PCI Reset */
#define E1000_ICH_FWSM_DISSW             0x10000000 /* FW Disables SW Writes */
/* FW established a valid mode */
#define E1000_ICH_FWSM_FW_VALID          0x00008000

#define E1000_ICH_MNG_IAMT_MODE          0x2

#define E1000_FWSM_PROXY_MODE            0x00000008 /* FW is in proxy mode */

/* Shared Receive Address Registers */
#define E1000_SHRAL(_i)  (0x05438 + ((_i) * 8))
#define E1000_SHRAH(_i)  (0x0543C + ((_i) * 8))
#define E1000_SHRAH_AV   0x80000000 /* Addr Valid bit */
#define E1000_SHRAH_MAV  0x40000000 /* Multicast Addr Valid bit */

#define E1000_H2ME             0x05B50    /* Host to ME */
#define E1000_H2ME_LSECREQ     0x00000001 /* Linksec Request */
#define E1000_H2ME_LSECA       0x00000002 /* Linksec Active */
#define E1000_H2ME_LSECSF      0x00000004 /* Linksec Failed */
#define E1000_H2ME_LSECD       0x00000008 /* Linksec Disabled */
#define E1000_H2ME_SLCAPD      0x00000010 /* Start LCAPD */
#define E1000_H2ME_IPV4_ARP_EN 0x00000020 /* Arp Offload enable bit */
#define E1000_H2ME_IPV6_NS_EN  0x00000040 /* NS Offload enable bit */

#define ID_LED_DEFAULT_ICH8LAN  ((ID_LED_DEF1_DEF2 << 12) | \
                                 (ID_LED_OFF1_OFF2 <<  8) | \
                                 (ID_LED_OFF1_ON2  <<  4) | \
                                 (ID_LED_DEF1_DEF2))

#define E1000_ICH_NVM_SIG_WORD           0x13
#define E1000_ICH_NVM_SIG_MASK           0xC000
#define E1000_ICH_NVM_VALID_SIG_MASK     0xC0
#define E1000_ICH_NVM_SIG_VALUE          0x80

#define E1000_ICH8_LAN_INIT_TIMEOUT      1500

#define E1000_FEXTNVM_SW_CONFIG        1
#define E1000_FEXTNVM_SW_CONFIG_ICH8M (1 << 27) /* Bit redefined for ICH8M */

#define E1000_FEXTNVM4_BEACON_DURATION_MASK    0x7
#define E1000_FEXTNVM4_BEACON_DURATION_8USEC   0x7
#define E1000_FEXTNVM4_BEACON_DURATION_16USEC  0x3

#define PCIE_ICH8_SNOOP_ALL   PCIE_NO_SNOOP_ALL

#define E1000_ICH_RAR_ENTRIES            7
#define E1000_PCH2_RAR_ENTRIES           5 /* RAR[0], SHRA[0-3] */

#define PHY_PAGE_SHIFT 5
#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \
                           ((reg) & MAX_PHY_REG_ADDRESS))
#define IGP3_KMRN_DIAG  PHY_REG(770, 19) /* KMRN Diagnostic */
#define IGP3_VR_CTRL    PHY_REG(776, 18) /* Voltage Regulator Control */
#define IGP3_CAPABILITY PHY_REG(776, 19) /* Capability */
#define IGP3_PM_CTRL    PHY_REG(769, 20) /* Power Management Control */

#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS         0x0002
#define IGP3_VR_CTRL_DEV_POWERDOWN_MODE_MASK 0x0300
#define IGP3_VR_CTRL_MODE_SHUTDOWN           0x0200
#define IGP3_PM_CTRL_FORCE_PWR_DOWN          0x0020

/* PHY Wakeup Registers and defines */
#define BM_RCTL         PHY_REG(BM_WUC_PAGE, 0)
#define BM_WUC          PHY_REG(BM_WUC_PAGE, 1)
#define BM_WUFC         PHY_REG(BM_WUC_PAGE, 2)
#define BM_WUS          PHY_REG(BM_WUC_PAGE, 3)
#define BM_RAR_L(_i)    (BM_PHY_REG(BM_WUC_PAGE, 16 + ((_i) << 2)))
#define BM_RAR_M(_i)    (BM_PHY_REG(BM_WUC_PAGE, 17 + ((_i) << 2)))
#define BM_RAR_H(_i)    (BM_PHY_REG(BM_WUC_PAGE, 18 + ((_i) << 2)))
#define BM_RAR_CTRL(_i) (BM_PHY_REG(BM_WUC_PAGE, 19 + ((_i) << 2)))
#define BM_MTA(_i)      (BM_PHY_REG(BM_WUC_PAGE, 128 + ((_i) << 1)))
#define BM_IPAV         (BM_PHY_REG(BM_WUC_PAGE, 64))
#define BM_IP4AT_L(_i)  (BM_PHY_REG(BM_WUC_PAGE, 82 + ((_i) * 2)))
#define BM_IP4AT_H(_i)  (BM_PHY_REG(BM_WUC_PAGE, 83 + ((_i) * 2)))

#define BM_SHRAL_LOWER(_i) (BM_PHY_REG(BM_WUC_PAGE, 44 + ((_i) * 4)))
#define BM_SHRAL_UPPER(_i) (BM_PHY_REG(BM_WUC_PAGE, 45 + ((_i) * 4)))
#define BM_SHRAH_LOWER(_i) (BM_PHY_REG(BM_WUC_PAGE, 46 + ((_i) * 4)))
#define BM_SHRAH_UPPER(_i) (BM_PHY_REG(BM_WUC_PAGE, 47 + ((_i) * 4)))

#define BM_RCTL_UPE           0x0001          /* Unicast Promiscuous Mode */
#define BM_RCTL_MPE           0x0002          /* Multicast Promiscuous Mode */
#define BM_RCTL_MO_SHIFT      3               /* Multicast Offset Shift */
#define BM_RCTL_MO_MASK       (3 << 3)        /* Multicast Offset Mask */
#define BM_RCTL_BAM           0x0020          /* Broadcast Accept Mode */
#define BM_RCTL_PMCF          0x0040          /* Pass MAC Control Frames */
#define BM_RCTL_RFCE          0x0080          /* Rx Flow Control Enable */

#define HV_LED_CONFIG		PHY_REG(768, 30) /* LED Configuration */
#define HV_MUX_DATA_CTRL               PHY_REG(776, 16)
#define HV_MUX_DATA_CTRL_GEN_TO_MAC    0x0400
#define HV_MUX_DATA_CTRL_FORCE_SPEED   0x0004
#define HV_SCC_UPPER		PHY_REG(778, 16) /* Single Collision Count */
#define HV_SCC_LOWER		PHY_REG(778, 17)
#define HV_ECOL_UPPER		PHY_REG(778, 18) /* Excessive Collision Count */
#define HV_ECOL_LOWER		PHY_REG(778, 19)
#define HV_MCC_UPPER		PHY_REG(778, 20) /* Multiple Collision Count */
#define HV_MCC_LOWER		PHY_REG(778, 21)
#define HV_LATECOL_UPPER	PHY_REG(778, 23) /* Late Collision Count */
#define HV_LATECOL_LOWER	PHY_REG(778, 24)
#define HV_COLC_UPPER		PHY_REG(778, 25) /* Collision Count */
#define HV_COLC_LOWER		PHY_REG(778, 26)
#define HV_DC_UPPER		PHY_REG(778, 27) /* Defer Count */
#define HV_DC_LOWER		PHY_REG(778, 28)
#define HV_TNCRS_UPPER		PHY_REG(778, 29) /* Transmit with no CRS */
#define HV_TNCRS_LOWER		PHY_REG(778, 30)

#define E1000_FCRTV_PCH     0x05F40 /* PCH Flow Control Refresh Timer Value */

#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
#define E1000_NVM_K1_ENABLE 0x1  /* NVM Enable K1 bit */

/* SMBus Address Phy Register */
#define HV_SMB_ADDR            PHY_REG(768, 26)
#define HV_SMB_ADDR_MASK       0x007F
#define HV_SMB_ADDR_PEC_EN     0x0200
#define HV_SMB_ADDR_VALID      0x0080

/* Strapping Option Register - RO */
#define E1000_STRAP                     0x0000C
#define E1000_STRAP_SMBUS_ADDRESS_MASK  0x00FE0000
#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17

/* OEM Bits Phy Register */
#define HV_OEM_BITS            PHY_REG(768, 25)
#define HV_OEM_BITS_LPLU       0x0004 /* Low Power Link Up */
#define HV_OEM_BITS_GBE_DIS    0x0040 /* Gigabit Disable */
#define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */

#define LCD_CFG_PHY_ADDR_BIT   0x0020 /* Phy address bit from LCD Config word */

/* KMRN Mode Control */
#define HV_KMRN_MODE_CTRL	PHY_REG(769, 16)
#define HV_KMRN_MDIO_SLOW	0x0400

/* PHY Power Management Control */
#define HV_PM_CTRL		PHY_REG(770, 17)

#define SW_FLAG_TIMEOUT    1000 /* SW Semaphore flag timeout in milliseconds */

/* PHY Low Power Idle Control */
#define I82579_LPI_CTRL			PHY_REG(772, 20)
#define I82579_LPI_CTRL_ENABLE_MASK	0x6000

/*
 * Additional interrupts need to be handled for ICH family:
 *  DSW = The FW changed the status of the DISSW bit in FWSM
 *  PHYINT = The LAN connected device generates an interrupt
 *  EPRST = Manageability reset event
 */
#define IMS_ICH_ENABLE_MASK (\
    E1000_IMS_DSW   | \
    E1000_IMS_PHYINT | \
    E1000_IMS_EPRST)

/* Additional interrupt register bit definitions */
#define E1000_ICR_LSECPNC       0x00004000          /* PN threshold - client */
#define E1000_IMS_LSECPNC       E1000_ICR_LSECPNC   /* PN threshold - client */
#define E1000_ICS_LSECPNC       E1000_ICR_LSECPNC   /* PN threshold - client */

/* Security Processing bit Indication */
#define E1000_RXDEXT_LINKSEC_STATUS_LSECH       0x01000000
#define E1000_RXDEXT_LINKSEC_ERROR_BIT_MASK     0x60000000
#define E1000_RXDEXT_LINKSEC_ERROR_NO_SA_MATCH  0x20000000
#define E1000_RXDEXT_LINKSEC_ERROR_REPLAY_ERROR 0x40000000
#define E1000_RXDEXT_LINKSEC_ERROR_BAD_SIG      0x60000000

/* Receive Address Initial CRC Calculation */
#define E1000_PCH_RAICC(_n)	(0x05F50 + ((_n) * 4))

void e1000_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
                                                 bool state);
void e1000_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
void e1000_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
void e1000_disable_gig_wol_ich8lan(struct e1000_hw *hw);
s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_config);
s32 e1000_hv_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
#endif