d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
90b66aad9f
freebsd-nq/sys/dev/aic7xxx/aicasm/Makefile

32 lines
507 B
Makefile
Raw Normal View History

Add support to aicasm for "downloaded constants". These are immediate operands that are set during seqeuncer program download instead of at assembly time. Convert the sequencer code to use" downloaded constants" for four run time constants that vary depending on the board type. This frees up 4 bytes of sequencer scratch ram space where these constants used to be stored and also removes the additional instructions required to load their values into the accumulator prior to using them. Remove the REJBYTE sram variable. The host driver can just as easly read the accumulator to get this value. The scratch ram savings is important as the old code used to clober the SCSICONF register on 274X cards which sits near the top of scratch ram space. The SCSICONF register controls bus termination, and clobbering it is not a good thing. Now we have 4 bytes to spare. This should fix the reported problems with cards that don't have devices attached to them failing with a stream of "Somone reset bus X" messages. Doug Ledford determined the cause of the problem, fixes by me.
1997-09-27 19:37:31 +00:00
# $Id: Makefile,v 1.3 1997/09/03 03:44:32 gibbs Exp $
Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c: New sequencer assembler for the aic7xxx adapters. This assembler performs some amount of register type checking, allows bit manipulation of symbolic constants, and generates "patch tables" for conditionalized downloading of portions of the program. This makes it easier to take full advantage of the different features of the aic7xxx cards without imposing run time penalies or being bound to the small memory footprints of the low end cards for features like target mode. aic7xxx.reg: New, assembler parsed, register definitions fo the aic7xxx cards. This was done primarily in anticipation of 7810 support which will have a different register layout, but should be able to use the same assembler. The kernel aic7xxx driver consumes a generated file in the compile directory to get the definitions of the register locations. aic7xxx.seq: Convert to the slighly different syntax of the new assembler. Conditionalize SCB_PAGING, ultra, and twin features which shaves quite a bit of space once the program is downloaded. Add code to leave the selection hardware enabled during reconnects that win bus arbitration. This ensures that we will rearbitrate as soon as the bus goes free instead of delaying for a bit. When we expect the bus to go free, perform all of the cleanup associated with that event "up front" and enter a loop awaiting bus free. If we see a REQ first, complain, but attempt to continue. This will hopefully address, or at least help diagnose, the "target didn't send identify" messages that have been reported. Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00
Make the aic7xxx sequencer assembler compile in the kernel's object directory. Rename (via repository copy) some files so that the potential for future conflicts is minimized. PR: conf/4363
1997-09-03 03:44:58 +00:00
PROG= aicasm
Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c: New sequencer assembler for the aic7xxx adapters. This assembler performs some amount of register type checking, allows bit manipulation of symbolic constants, and generates "patch tables" for conditionalized downloading of portions of the program. This makes it easier to take full advantage of the different features of the aic7xxx cards without imposing run time penalies or being bound to the small memory footprints of the low end cards for features like target mode. aic7xxx.reg: New, assembler parsed, register definitions fo the aic7xxx cards. This was done primarily in anticipation of 7810 support which will have a different register layout, but should be able to use the same assembler. The kernel aic7xxx driver consumes a generated file in the compile directory to get the definitions of the register locations. aic7xxx.seq: Convert to the slighly different syntax of the new assembler. Conditionalize SCB_PAGING, ultra, and twin features which shaves quite a bit of space once the program is downloaded. Add code to leave the selection hardware enabled during reconnects that win bus arbitration. This ensures that we will rearbitrate as soon as the bus goes free instead of delaying for a bit. When we expect the bus to go free, perform all of the cleanup associated with that event "up front" and enter a loop awaiting bus free. If we see a REQ first, complain, but attempt to continue. This will hopefully address, or at least help diagnose, the "target didn't send identify" messages that have been reported. Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00
Make the aic7xxx sequencer assembler compile in the kernel's object directory. Rename (via repository copy) some files so that the potential for future conflicts is minimized. PR: conf/4363
1997-09-03 03:44:58 +00:00
CSRCS= aicasm.c aicasm_symbol.c
GENSRCS= aicasm_gram.c aicasm_scan.c
Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c: New sequencer assembler for the aic7xxx adapters. This assembler performs some amount of register type checking, allows bit manipulation of symbolic constants, and generates "patch tables" for conditionalized downloading of portions of the program. This makes it easier to take full advantage of the different features of the aic7xxx cards without imposing run time penalies or being bound to the small memory footprints of the low end cards for features like target mode. aic7xxx.reg: New, assembler parsed, register definitions fo the aic7xxx cards. This was done primarily in anticipation of 7810 support which will have a different register layout, but should be able to use the same assembler. The kernel aic7xxx driver consumes a generated file in the compile directory to get the definitions of the register locations. aic7xxx.seq: Convert to the slighly different syntax of the new assembler. Conditionalize SCB_PAGING, ultra, and twin features which shaves quite a bit of space once the program is downloaded. Add code to leave the selection hardware enabled during reconnects that win bus arbitration. This ensures that we will rearbitrate as soon as the bus goes free instead of delaying for a bit. When we expect the bus to go free, perform all of the cleanup associated with that event "up front" and enter a loop awaiting bus free. If we see a REQ first, complain, but attempt to continue. This will hopefully address, or at least help diagnose, the "target didn't send identify" messages that have been reported. Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00
Make the aic7xxx sequencer assembler compile in the kernel's object directory. Rename (via repository copy) some files so that the potential for future conflicts is minimized. PR: conf/4363
1997-09-03 03:44:58 +00:00
GENHDRS= y.tab.h
Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c: New sequencer assembler for the aic7xxx adapters. This assembler performs some amount of register type checking, allows bit manipulation of symbolic constants, and generates "patch tables" for conditionalized downloading of portions of the program. This makes it easier to take full advantage of the different features of the aic7xxx cards without imposing run time penalies or being bound to the small memory footprints of the low end cards for features like target mode. aic7xxx.reg: New, assembler parsed, register definitions fo the aic7xxx cards. This was done primarily in anticipation of 7810 support which will have a different register layout, but should be able to use the same assembler. The kernel aic7xxx driver consumes a generated file in the compile directory to get the definitions of the register locations. aic7xxx.seq: Convert to the slighly different syntax of the new assembler. Conditionalize SCB_PAGING, ultra, and twin features which shaves quite a bit of space once the program is downloaded. Add code to leave the selection hardware enabled during reconnects that win bus arbitration. This ensures that we will rearbitrate as soon as the bus goes free instead of delaying for a bit. When we expect the bus to go free, perform all of the cleanup associated with that event "up front" and enter a loop awaiting bus free. If we see a REQ first, complain, but attempt to continue. This will hopefully address, or at least help diagnose, the "target didn't send identify" messages that have been reported. Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00
SRCS= ${GENSRCS} ${CSRCS}
Make the aic7xxx sequencer assembler compile in the kernel's object directory. Rename (via repository copy) some files so that the potential for future conflicts is minimized. PR: conf/4363
1997-09-03 03:44:58 +00:00
CLEANFILES+= ${GENSRCS} ${GENHDRS} y.output
Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c: New sequencer assembler for the aic7xxx adapters. This assembler performs some amount of register type checking, allows bit manipulation of symbolic constants, and generates "patch tables" for conditionalized downloading of portions of the program. This makes it easier to take full advantage of the different features of the aic7xxx cards without imposing run time penalies or being bound to the small memory footprints of the low end cards for features like target mode. aic7xxx.reg: New, assembler parsed, register definitions fo the aic7xxx cards. This was done primarily in anticipation of 7810 support which will have a different register layout, but should be able to use the same assembler. The kernel aic7xxx driver consumes a generated file in the compile directory to get the definitions of the register locations. aic7xxx.seq: Convert to the slighly different syntax of the new assembler. Conditionalize SCB_PAGING, ultra, and twin features which shaves quite a bit of space once the program is downloaded. Add code to leave the selection hardware enabled during reconnects that win bus arbitration. This ensures that we will rearbitrate as soon as the bus goes free instead of delaying for a bit. When we expect the bus to go free, perform all of the cleanup associated with that event "up front" and enter a loop awaiting bus free. If we see a REQ first, complain, but attempt to continue. This will hopefully address, or at least help diagnose, the "target didn't send identify" messages that have been reported. Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00
DPADD+= ${LIBL}
LDADD+= -ll
CFLAGS += -I. so that building in an obj directory works.
1997-04-03 05:56:00 +00:00
Make the aic7xxx sequencer assembler compile in the kernel's object directory. Rename (via repository copy) some files so that the potential for future conflicts is minimized. PR: conf/4363
1997-09-03 03:44:58 +00:00
# Correct path for kernel builds
# Don't rely on the kernel's .depend file
.ifdef MAKESRCPATH
.PATH: ${MAKESRCPATH}
DEPENDFILE=
.endif
CFLAGS += -I. so that building in an obj directory works.
1997-04-03 05:56:00 +00:00
CFLAGS+= -I.
Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c: New sequencer assembler for the aic7xxx adapters. This assembler performs some amount of register type checking, allows bit manipulation of symbolic constants, and generates "patch tables" for conditionalized downloading of portions of the program. This makes it easier to take full advantage of the different features of the aic7xxx cards without imposing run time penalies or being bound to the small memory footprints of the low end cards for features like target mode. aic7xxx.reg: New, assembler parsed, register definitions fo the aic7xxx cards. This was done primarily in anticipation of 7810 support which will have a different register layout, but should be able to use the same assembler. The kernel aic7xxx driver consumes a generated file in the compile directory to get the definitions of the register locations. aic7xxx.seq: Convert to the slighly different syntax of the new assembler. Conditionalize SCB_PAGING, ultra, and twin features which shaves quite a bit of space once the program is downloaded. Add code to leave the selection hardware enabled during reconnects that win bus arbitration. This ensures that we will rearbitrate as soon as the bus goes free instead of delaying for a bit. When we expect the bus to go free, perform all of the cleanup associated with that event "up front" and enter a loop awaiting bus free. If we see a REQ first, complain, but attempt to continue. This will hopefully address, or at least help diagnose, the "target didn't send identify" messages that have been reported. Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00
NOMAN= noman
Add support to aicasm for "downloaded constants". These are immediate operands that are set during seqeuncer program download instead of at assembly time. Convert the sequencer code to use" downloaded constants" for four run time constants that vary depending on the board type. This frees up 4 bytes of sequencer scratch ram space where these constants used to be stored and also removes the additional instructions required to load their values into the accumulator prior to using them. Remove the REJBYTE sram variable. The host driver can just as easly read the accumulator to get this value. The scratch ram savings is important as the old code used to clober the SCSICONF register on 274X cards which sits near the top of scratch ram space. The SCSICONF register controls bus termination, and clobbering it is not a good thing. Now we have 4 bytes to spare. This should fix the reported problems with cards that don't have devices attached to them failing with a stream of "Somone reset bus X" messages. Doug Ledford determined the cause of the problem, fixes by me.
1997-09-27 19:37:31 +00:00
.ifdef DEBUG
CFLAGS+= -DDEBUG -g
YFLAGS+= -t
LFLAGS+= -d
.endif
Makefile gram.y scan.l sequencer.h symbol.c symbol.h aic7xxx_asm.c: New sequencer assembler for the aic7xxx adapters. This assembler performs some amount of register type checking, allows bit manipulation of symbolic constants, and generates "patch tables" for conditionalized downloading of portions of the program. This makes it easier to take full advantage of the different features of the aic7xxx cards without imposing run time penalies or being bound to the small memory footprints of the low end cards for features like target mode. aic7xxx.reg: New, assembler parsed, register definitions fo the aic7xxx cards. This was done primarily in anticipation of 7810 support which will have a different register layout, but should be able to use the same assembler. The kernel aic7xxx driver consumes a generated file in the compile directory to get the definitions of the register locations. aic7xxx.seq: Convert to the slighly different syntax of the new assembler. Conditionalize SCB_PAGING, ultra, and twin features which shaves quite a bit of space once the program is downloaded. Add code to leave the selection hardware enabled during reconnects that win bus arbitration. This ensures that we will rearbitrate as soon as the bus goes free instead of delaying for a bit. When we expect the bus to go free, perform all of the cleanup associated with that event "up front" and enter a loop awaiting bus free. If we see a REQ first, complain, but attempt to continue. This will hopefully address, or at least help diagnose, the "target didn't send identify" messages that have been reported. Spelling corrections obtained from NetBSD.
1997-03-16 07:08:19 +00:00
.include <bsd.prog.mk>
Reference in New Issue Copy Permalink