d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
9c3fd40489
freebsd-nq/sys/dev/wi/if_wi.c

3237 lines
85 KiB
C
Raw Normal View History

new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* $NetBSD: wi.c,v 1.109 2003/01/09 08:52:19 dyoung Exp $ */
Start each of the license/copyright comments with /*-, minor shuffle of lines
2005-01-06 01:43:34 +00:00
/*-
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
* Copyright (c) 1997, 1998, 1999
* Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
* Lucent WaveLAN/IEEE 802.11 PCMCIA driver.
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
*
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
* Original FreeBSD driver written by Bill Paul <wpaul@ctr.columbia.edu>
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
* Electrical Engineering Department
* Columbia University, New York City
*/
/*
- Fix up some comments in if_wi.c (no code changes) - Mention that the 6Mbps turbo adapters are supported in HARDWARE.TXT and RELNOTES.TXT and the wi.4 man page - Mention turbo adapters in the wicontrol.8 man page and provide a complete table of available transmit speed settings
1999-05-22 16:12:54 +00:00
* The WaveLAN/IEEE adapter is the second generation of the WaveLAN
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
* from Lucent. Unlike the older cards, the new ones are programmed
* entirely via a firmware-driven controller called the Hermes.
* Unfortunately, Lucent will not release the Hermes programming manual
* without an NDA (if at all). What they do release is an API library
* called the HCF (Hardware Control Functions) which is supposed to
* do the device-specific operations of a device driver for you. The
* publically available version of the HCF library (the 'HCF Light') is
- Fix up some comments in if_wi.c (no code changes) - Mention that the 6Mbps turbo adapters are supported in HARDWARE.TXT and RELNOTES.TXT and the wi.4 man page - Mention turbo adapters in the wicontrol.8 man page and provide a complete table of available transmit speed settings
1999-05-22 16:12:54 +00:00
* a) extremely gross, b) lacks certain features, particularly support
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
* for 802.11 frames, and c) is contaminated by the GNU Public License.
*
* This driver does not use the HCF or HCF Light at all. Instead, it
* programs the Hermes controller directly, using information gleaned
* from the HCF Light code and corresponding documentation.
*
Make this driver compile for -stable also to prep for MFC
2002-04-26 23:11:23 +00:00
* This driver supports the ISA, PCMCIA and PCI versions of the Lucent
* WaveLan cards (based on the Hermes chipset), as well as the newer
* Prism 2 chipsets with firmware from Intersil and Symbol.
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
*/
Use __FBSDID rather than rcsid[].
2003-04-03 21:36:33 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#define WI_HERMES_AUTOINC_WAR /* Work around data write autoinc bug. */
#define WI_HERMES_STATS_WAR /* Work around stats counter bug. */
#define NBPFILTER 1
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
#include <sys/param.h>
#include <sys/systm.h>
Untimeout before calling timeout. I think that I have caught all the cases where we were scheduling a timeout multiple times, but am not positive.
2002-04-29 06:55:46 +00:00
#if __FreeBSD_version >= 500033
Move the new byte order function prototypes from <sys/param.h> to <sys/endian.h>. This puts us in line with NetBSD and OpenBSD.
2002-04-26 22:48:23 +00:00
#include <sys/endian.h>
Untimeout before calling timeout. I think that I have caught all the cases where we were scheduling a timeout multiple times, but am not positive.
2002-04-29 06:55:46 +00:00
#endif
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
#include <sys/sockio.h>
#include <sys/mbuf.h>
KSE Milestone 2 Note ALL MODULES MUST BE RECOMPILED make the kernel aware that there are smaller units of scheduling than the process. (but only allow one thread per process at this time). This is functionally equivalent to teh previousl -current except that there is a thread associated with each process. Sorry john! (your next MFC will be a doosie!) Reviewed by: peter@freebsd.org, dillon@freebsd.org X-MFC after: ha ha ha ha
2001-09-12 08:38:13 +00:00
#include <sys/proc.h>
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
#include <sys/kernel.h>
#include <sys/socket.h>
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
#include <sys/module.h>
#include <sys/bus.h>
unifdef -DWI_HOSTAP, like OpenBSD does
2002-04-12 06:01:28 +00:00
#include <sys/random.h>
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
#include <sys/syslog.h>
#include <sys/sysctl.h>
#include <machine/bus.h>
#include <machine/resource.h>
Make this driver compile for -stable also to prep for MFC
2002-04-26 23:11:23 +00:00
#include <machine/clock.h>
update for new 802.11 support
2003-06-28 06:17:26 +00:00
#include <machine/atomic.h>
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
#include <sys/rman.h>
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
#include <net/if.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/if_types.h>
update for new 802.11 support
2003-06-28 06:17:26 +00:00
#include <net80211/ieee80211_var.h>
#include <net80211/ieee80211_ioctl.h>
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
#include <net80211/ieee80211_radiotap.h>
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
#include <netinet/in.h>
#include <netinet/in_systm.h>
#include <netinet/in_var.h>
#include <netinet/ip.h>
#include <netinet/if_ether.h>
#include <net/bpf.h>
Move if_wl.c from sys/i386/isa to dev/wi - it is not i386 (or even isa) specific.
2001-01-09 00:44:33 +00:00
#include <dev/wi/if_wavelan_ieee.h>
#include <dev/wi/if_wireg.h>
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
#include <dev/wi/if_wivar.h>
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Remove __P to reduce diffs with NetBSD and my private tree.
2002-03-05 16:12:41 +00:00
static void wi_start(struct ifnet *);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int wi_reset(struct wi_softc *);
Remove __P to reduce diffs with NetBSD and my private tree.
2002-03-05 16:12:41 +00:00
static void wi_watchdog(struct ifnet *);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int wi_ioctl(struct ifnet *, u_long, caddr_t);
static int wi_media_change(struct ifnet *);
Remove __P to reduce diffs with NetBSD and my private tree.
2002-03-05 16:12:41 +00:00
static void wi_media_status(struct ifnet *, struct ifmediareq *);
Currently, each wireless networking driver has it's own control program despite the fact that most people want to set exactly the same settings regardless of which card they have. It has been repeatidly suggested that this configuration should be done via ifconfig. This patch implements the required functionality in ifconfig and add support to the wi and an drivers. It also provides partial, untested support for the awi driver. PR: 25577 Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
2001-05-26 09:27:08 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void wi_rx_intr(struct wi_softc *);
static void wi_tx_intr(struct wi_softc *);
static void wi_tx_ex_intr(struct wi_softc *);
static void wi_info_intr(struct wi_softc *);
static int wi_get_cfg(struct ifnet *, u_long, caddr_t);
static int wi_set_cfg(struct ifnet *, u_long, caddr_t);
static int wi_write_txrate(struct wi_softc *);
static int wi_write_wep(struct wi_softc *);
static int wi_write_multi(struct wi_softc *);
static int wi_alloc_fid(struct wi_softc *, int, int *);
static void wi_read_nicid(struct wi_softc *);
static int wi_write_ssid(struct wi_softc *, int, u_int8_t *, int);
static int wi_cmd(struct wi_softc *, int, int, int, int);
static int wi_seek_bap(struct wi_softc *, int, int);
static int wi_read_bap(struct wi_softc *, int, int, void *, int);
static int wi_write_bap(struct wi_softc *, int, int, void *, int);
static int wi_mwrite_bap(struct wi_softc *, int, int, struct mbuf *, int);
static int wi_read_rid(struct wi_softc *, int, void *, int *);
static int wi_write_rid(struct wi_softc *, int, void *, int);
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
static int wi_newstate(struct ieee80211com *, enum ieee80211_state, int);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
static int wi_scan_ap(struct wi_softc *, u_int16_t, u_int16_t);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void wi_scan_result(struct wi_softc *, int, int);
static void wi_dump_pkt(struct wi_frame *, struct ieee80211_node *, int rssi);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
static int wi_get_debug(struct wi_softc *, struct wi_req *);
static int wi_set_debug(struct wi_softc *, struct wi_req *);
o Comment out the symbol download code for 4.x. o Add hooks for doing power management of the output signal. o Minor hacks to make flexlint happy wrt staticness of functions.
2002-10-14 01:59:57 +00:00
#if __FreeBSD_version >= 500000
Move the symbol firmware loading routines into if_wi. Define some basic firmware downloading commands.
2002-08-15 07:13:17 +00:00
/* support to download firmware for symbol CF card */
static int wi_symbol_write_firm(struct wi_softc *, const void *, int,
const void *, int);
static int wi_symbol_set_hcr(struct wi_softc *, int);
o Comment out the symbol download code for 4.x. o Add hooks for doing power management of the output signal. o Minor hacks to make flexlint happy wrt staticness of functions.
2002-10-14 01:59:57 +00:00
#endif
Move the symbol firmware loading routines into if_wi. Define some basic firmware downloading commands.
2002-08-15 07:13:17 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static __inline int
wi_write_val(struct wi_softc *sc, int rid, u_int16_t val)
{
val = htole16(val);
return wi_write_rid(sc, rid, &val, sizeof(val));
}
correct sysctl names and move them to hw.wi: hw.wi.txerate controls the rate at which tx errors are printed (default to 0); hw.wi.debug control the debug msgs and is only present when WI_DEBUG is defined at compile time (the default for the moment) Requested by: imp
2003-01-20 20:55:37 +00:00
SYSCTL_NODE(_hw, OID_AUTO, wi, CTLFLAG_RD, 0, "Wireless driver parameters");
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static struct timeval lasttxerror; /* time of last tx error msg */
static int curtxeps; /* current tx error msgs/sec */
Change default setting of hw.wi.txerate to zero so that tx error msgs are ignored (as before). This was the original setting but a bug in ppsratecheck made me do stupid things.
2003-02-26 17:18:35 +00:00
static int wi_txerate = 0; /* tx error rate: max msgs/sec */
correct sysctl names and move them to hw.wi: hw.wi.txerate controls the rate at which tx errors are printed (default to 0); hw.wi.debug control the debug msgs and is only present when WI_DEBUG is defined at compile time (the default for the moment) Requested by: imp
2003-01-20 20:55:37 +00:00
SYSCTL_INT(_hw_wi, OID_AUTO, txerate, CTLFLAG_RW, &wi_txerate,
Change default setting of hw.wi.txerate to zero so that tx error msgs are ignored (as before). This was the original setting but a bug in ppsratecheck made me do stupid things.
2003-02-26 17:18:35 +00:00
0, "max tx error msgs/sec; 0 to disable msgs");
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#define WI_DEBUG
#ifdef WI_DEBUG
static int wi_debug = 0;
correct sysctl names and move them to hw.wi: hw.wi.txerate controls the rate at which tx errors are printed (default to 0); hw.wi.debug control the debug msgs and is only present when WI_DEBUG is defined at compile time (the default for the moment) Requested by: imp
2003-01-20 20:55:37 +00:00
SYSCTL_INT(_hw_wi, OID_AUTO, debug, CTLFLAG_RW, &wi_debug,
0, "control debugging printfs");
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#define DPRINTF(X) if (wi_debug) printf X
#define DPRINTF2(X) if (wi_debug > 1) printf X
#define IFF_DUMPPKTS(_ifp) \
(((_ifp)->if_flags & (IFF_DEBUG|IFF_LINK2)) == (IFF_DEBUG|IFF_LINK2))
#else
#define DPRINTF(X)
#define DPRINTF2(X)
#define IFF_DUMPPKTS(_ifp) 0
#endif
#define WI_INTRS (WI_EV_RX | WI_EV_ALLOC | WI_EV_INFO)
Add support for the Addtron AWA100 PCI wireless card. The AWA100 is a PCI board with a PLX 9052 chip that's used to talk to the pccard inserted into the board. Remove a redundant $FreeBSD while I'm here.
2001-03-28 05:05:05 +00:00
MFNetBSD: wi.c 1.64: Table driven IDs (ichiro) 1.59: Don't use magic numbers (ichiro) Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent cards (and submit those changes back to ichiro-san) Obtained from: NetBSD
2002-04-04 21:40:37 +00:00
struct wi_card_ident wi_card_ident[] = {
/* CARD_ID CARD_NAME FIRM_TYPE */
{ WI_NIC_LUCENT_ID, WI_NIC_LUCENT_STR, WI_LUCENT },
{ WI_NIC_SONY_ID, WI_NIC_SONY_STR, WI_LUCENT },
{ WI_NIC_LUCENT_EMB_ID, WI_NIC_LUCENT_EMB_STR, WI_LUCENT },
{ WI_NIC_EVB2_ID, WI_NIC_EVB2_STR, WI_INTERSIL },
{ WI_NIC_HWB3763_ID, WI_NIC_HWB3763_STR, WI_INTERSIL },
{ WI_NIC_HWB3163_ID, WI_NIC_HWB3163_STR, WI_INTERSIL },
{ WI_NIC_HWB3163B_ID, WI_NIC_HWB3163B_STR, WI_INTERSIL },
{ WI_NIC_EVB3_ID, WI_NIC_EVB3_STR, WI_INTERSIL },
{ WI_NIC_HWB1153_ID, WI_NIC_HWB1153_STR, WI_INTERSIL },
{ WI_NIC_P2_SST_ID, WI_NIC_P2_SST_STR, WI_INTERSIL },
{ WI_NIC_EVB2_SST_ID, WI_NIC_EVB2_SST_STR, WI_INTERSIL },
{ WI_NIC_3842_EVA_ID, WI_NIC_3842_EVA_STR, WI_INTERSIL },
{ WI_NIC_3842_PCMCIA_AMD_ID, WI_NIC_3842_PCMCIA_STR, WI_INTERSIL },
{ WI_NIC_3842_PCMCIA_SST_ID, WI_NIC_3842_PCMCIA_STR, WI_INTERSIL },
Differentiate between AT45DB011 compatible large serial flash parts and the AT24C08 small serial flash parts. We still report these as the same part (since we group things already), but now we recognize the small serial versions as well.
2002-08-05 07:24:02 +00:00
{ WI_NIC_3842_PCMCIA_ATL_ID, WI_NIC_3842_PCMCIA_STR, WI_INTERSIL },
{ WI_NIC_3842_PCMCIA_ATS_ID, WI_NIC_3842_PCMCIA_STR, WI_INTERSIL },
MFNetBSD: wi.c 1.64: Table driven IDs (ichiro) 1.59: Don't use magic numbers (ichiro) Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent cards (and submit those changes back to ichiro-san) Obtained from: NetBSD
2002-04-04 21:40:37 +00:00
{ WI_NIC_3842_MINI_AMD_ID, WI_NIC_3842_MINI_STR, WI_INTERSIL },
{ WI_NIC_3842_MINI_SST_ID, WI_NIC_3842_MINI_STR, WI_INTERSIL },
Differentiate between AT45DB011 compatible large serial flash parts and the AT24C08 small serial flash parts. We still report these as the same part (since we group things already), but now we recognize the small serial versions as well.
2002-08-05 07:24:02 +00:00
{ WI_NIC_3842_MINI_ATL_ID, WI_NIC_3842_MINI_STR, WI_INTERSIL },
{ WI_NIC_3842_MINI_ATS_ID, WI_NIC_3842_MINI_STR, WI_INTERSIL },
MFNetBSD: wi.c 1.64: Table driven IDs (ichiro) 1.59: Don't use magic numbers (ichiro) Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent cards (and submit those changes back to ichiro-san) Obtained from: NetBSD
2002-04-04 21:40:37 +00:00
{ WI_NIC_3842_PCI_AMD_ID, WI_NIC_3842_PCI_STR, WI_INTERSIL },
{ WI_NIC_3842_PCI_SST_ID, WI_NIC_3842_PCI_STR, WI_INTERSIL },
Differentiate between AT45DB011 compatible large serial flash parts and the AT24C08 small serial flash parts. We still report these as the same part (since we group things already), but now we recognize the small serial versions as well.
2002-08-05 07:24:02 +00:00
{ WI_NIC_3842_PCI_ATS_ID, WI_NIC_3842_PCI_STR, WI_INTERSIL },
{ WI_NIC_3842_PCI_ATL_ID, WI_NIC_3842_PCI_STR, WI_INTERSIL },
MFNetBSD: wi.c 1.64: Table driven IDs (ichiro) 1.59: Don't use magic numbers (ichiro) Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent cards (and submit those changes back to ichiro-san) Obtained from: NetBSD
2002-04-04 21:40:37 +00:00
{ WI_NIC_P3_PCMCIA_AMD_ID, WI_NIC_P3_PCMCIA_STR, WI_INTERSIL },
{ WI_NIC_P3_PCMCIA_SST_ID, WI_NIC_P3_PCMCIA_STR, WI_INTERSIL },
Differentiate between AT45DB011 compatible large serial flash parts and the AT24C08 small serial flash parts. We still report these as the same part (since we group things already), but now we recognize the small serial versions as well.
2002-08-05 07:24:02 +00:00
{ WI_NIC_P3_PCMCIA_ATL_ID, WI_NIC_P3_PCMCIA_STR, WI_INTERSIL },
{ WI_NIC_P3_PCMCIA_ATS_ID, WI_NIC_P3_PCMCIA_STR, WI_INTERSIL },
MFNetBSD: wi.c 1.64: Table driven IDs (ichiro) 1.59: Don't use magic numbers (ichiro) Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent cards (and submit those changes back to ichiro-san) Obtained from: NetBSD
2002-04-04 21:40:37 +00:00
{ WI_NIC_P3_MINI_AMD_ID, WI_NIC_P3_MINI_STR, WI_INTERSIL },
{ WI_NIC_P3_MINI_SST_ID, WI_NIC_P3_MINI_STR, WI_INTERSIL },
Differentiate between AT45DB011 compatible large serial flash parts and the AT24C08 small serial flash parts. We still report these as the same part (since we group things already), but now we recognize the small serial versions as well.
2002-08-05 07:24:02 +00:00
{ WI_NIC_P3_MINI_ATL_ID, WI_NIC_P3_MINI_STR, WI_INTERSIL },
{ WI_NIC_P3_MINI_ATS_ID, WI_NIC_P3_MINI_STR, WI_INTERSIL },
MFNetBSD: wi.c 1.64: Table driven IDs (ichiro) 1.59: Don't use magic numbers (ichiro) Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent cards (and submit those changes back to ichiro-san) Obtained from: NetBSD
2002-04-04 21:40:37 +00:00
{ 0, NULL, 0 },
};
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
devclass_t wi_devclass;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
First cut at breaking out the bus attachment from the bus independent part of the driver. Also, move the softc and some other stuff to if_wivar.h from if_wireg.h to make future merging activities easier.
2002-04-02 02:38:35 +00:00
int
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_attach(device_t dev)
Add support for the Addtron AWA100 PCI wireless card. The AWA100 is a PCI board with a PLX 9052 chip that's used to talk to the pccard inserted into the board. Remove a redundant $FreeBSD while I'm here.
2001-03-28 05:05:05 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = device_get_softc(dev);
struct ieee80211com *ic = &sc->sc_ic;
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp;
update for new 802.11 support
2003-06-28 06:17:26 +00:00
int i, nrates, buflen;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
u_int16_t val;
u_int8_t ratebuf[2 + IEEE80211_RATE_SIZE];
update for new 802.11 support
2003-06-28 06:17:26 +00:00
struct ieee80211_rateset *rs;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static const u_int8_t empty_macaddr[IEEE80211_ADDR_LEN] = {
0x00, 0x00, 0x00, 0x00, 0x00, 0x00
};
int error;
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
ifp = sc->sc_ifp = if_alloc(IFT_ETHER);
if (ifp == NULL) {
device_printf(dev, "can not if_alloc\n");
wi_free(dev);
return (ENOSPC);
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/*
* NB: no locking is needed here; don't put it here
* unless you can prove it!
*/
mark interrupt handlers MPSAFE
2003-10-29 18:32:14 +00:00
error = bus_setup_intr(dev, sc->irq, INTR_TYPE_NET | INTR_MPSAFE,
Fix a couple style nits, no code changes. Turn one magic number into a #defined constant, wrap a few long lines, etc... Also remove stupid 'all your base are belong to us' joke from comment that I don't really care to see immortalized in the source tree.
2001-03-29 19:11:45 +00:00
wi_intr, sc, &sc->wi_intrhand);
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
if (error) {
device_printf(dev, "bus_setup_intr() failed! (%d)\n", error);
wi_free(dev);
return (error);
}
Make this driver compile for -stable also to prep for MFC
2002-04-26 23:11:23 +00:00
#if __FreeBSD_version >= 500000
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
mtx_init(&sc->sc_mtx, device_get_nameunit(dev), MTX_NETWORK_LOCK,
Change callers of mtx_init() to pass in an appropriate lock type name. In most cases NULL is passed, but in some cases such as network driver locks (which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used. Tested on: i386, alpha, sparc64
2002-04-04 21:03:38 +00:00
MTX_DEF | MTX_RECURSE);
Make this driver compile for -stable also to prep for MFC
2002-04-26 23:11:23 +00:00
#endif
Update the wi driver to use mutexes instead of spls.
2000-10-13 20:33:24 +00:00
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
sc->sc_firmware_type = WI_NOTYPE;
Older versions of the intersil firmware is a lot slower than newer versions of the firmware. It responds more slowly to commands, and we bogusly failed them. We assume that all versions of the intersil firmware before 1.0 are 10 times slower and will give it 10x the time to finish. # for 5.2 we should always just assume 5s.
2003-12-09 07:41:07 +00:00
sc->wi_cmd_count = 500;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
/* Reset the NIC. */
Remove bogus UNLOCK in if_wi.c. Since we no longer WILOCK() in the attach routine, calling WIUNLOCK in the error case of one of the ifs for that routine is now bogus. This should have been removed when the WILOCK() was removed, but wasn't. Submitted by: "Harti Brandt" <brandt@fokus.fraunhofer.de>
2003-03-11 17:13:33 +00:00
if (wi_reset(sc) != 0)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return ENXIO; /* XXX */
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Try to read the station address twice during the probe. I've seen a LinkSys card here in the office where reading the station address fails the first time, but works find afterwards. Without this, the probe fails. I don't think this will negatively impact any existing cards, but I want to confirm this before MFC'ing.
2001-05-10 17:17:24 +00:00
/*
* Read the station address.
* And do it twice. I've seen PRISM-based cards that return
* an error when trying to read it the first time, which causes
* the probe to fail.
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
buflen = IEEE80211_ADDR_LEN;
error = wi_read_rid(sc, WI_RID_MAC_NODE, ic->ic_myaddr, &buflen);
if (error != 0) {
buflen = IEEE80211_ADDR_LEN;
error = wi_read_rid(sc, WI_RID_MAC_NODE, ic->ic_myaddr, &buflen);
}
if (error || IEEE80211_ADDR_EQ(ic->ic_myaddr, empty_macaddr)) {
if (error != 0)
device_printf(dev, "mac read failed %d\n", error);
When the MAC address is reported all zeros, then error is necessarily 0. This means that we 'succeed' the attach, even after we've freed the internal data bits. This leads to a panic when you eject the card with this problem. Set error = ENXIO in the mac read zeros case.
2005-08-05 04:56:14 +00:00
else {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
device_printf(dev, "mac read failed (all zeros)\n");
When the MAC address is reported all zeros, then error is necessarily 0. This means that we 'succeed' the attach, even after we've freed the internal data bits. This leads to a panic when you eject the card with this problem. Set error = ENXIO in the mac read zeros case.
2005-08-05 04:56:14 +00:00
error = ENXIO;
}
Try to INIT the cards up to 5 times in a row rather than just once. It appears that some of the new PRISM2 cards need it. Fail the probe if we fail to read the MAC address. Fix a comment. Delete the unload printf. The bus system now prints this message.
2001-04-04 06:03:39 +00:00
wi_free(dev);
return (error);
}
Implement prism2 detection from NetBSD. This mostly obsoletes the prism2 flag in pccard.conf, but I'm leaving it place for the moment in case the small sample of PrismII cards that I've tried is not representative. MFC After: 30 days Obtained from: NetBSD
2001-12-05 08:57:36 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Read NIC identification */
wi_read_nicid(sc);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
ifp->if_softc = sc;
Replace the if_name and if_unit members of struct ifnet with new members if_xname, if_dname, and if_dunit. if_xname is the name of the interface and if_dname/unit are the driver name and instance. This change paves the way for interface renaming and enhanced pseudo device creation and configuration symantics. Approved By: re (in principle) Reviewed By: njl, imp Tested On: i386, amd64, sparc64 Obtained From: NetBSD (if_xname)
2003-10-31 18:32:15 +00:00
if_initname(ifp, device_get_name(dev), device_get_unit(dev));
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
ifp->if_ioctl = wi_ioctl;
ifp->if_start = wi_start;
ifp->if_watchdog = wi_watchdog;
ifp->if_init = wi_init;
Second part of ALTQ driver modifications, covering: an(4), ath(4), hme(4), ndis(4), vr(4) and wi(4) Please help testing: http://people.freebsd.org/~mlaier/ALTQ_driver/ Tested by: Vaidas Damosevicius (an, ath, wi) Roman Divacky (vr) Submitted by: yongari (hme)
2004-08-01 23:58:04 +00:00
IFQ_SET_MAXLEN(&ifp->if_snd, IFQ_MAXLEN);
ifp->if_snd.ifq_drv_maxlen = IFQ_MAXLEN;
IFQ_SET_READY(&ifp->if_snd);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ic->ic_ifp = ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ic->ic_phytype = IEEE80211_T_DS;
ic->ic_opmode = IEEE80211_M_STA;
ic->ic_state = IEEE80211_S_INIT;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ic->ic_caps = IEEE80211_C_PMGT
| IEEE80211_C_WEP /* everyone supports WEP */
;
ic->ic_max_aid = WI_MAX_AID;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
update for new 802.11 support
2003-06-28 06:17:26 +00:00
/*
* Query the card for available channels and setup the
* channel table. We assume these are all 11b channels.
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
buflen = sizeof(val);
if (wi_read_rid(sc, WI_RID_CHANNEL_LIST, &val, &buflen) != 0)
val = htole16(0x1fff); /* assume 1-11 */
update for new 802.11 support
2003-06-28 06:17:26 +00:00
KASSERT(val != 0, ("wi_attach: no available channels listed!"));
val <<= 1; /* shift for base 1 indices */
for (i = 1; i < 16; i++) {
Invert conditional and use continue to reduce nesting.
2005-04-13 03:36:24 +00:00
if (!isset((u_int8_t*)&val, i))
continue;
ic->ic_channels[i].ic_freq =
ieee80211_ieee2mhz(i, IEEE80211_CHAN_B);
ic->ic_channels[i].ic_flags = IEEE80211_CHAN_B;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Modify wicontrol(8) and wi(4) to allow setting the frequency of the WaveLAN's radio modem. The default is whatever the NIC uses since NICs sold in different countries may default to different frequencies. (The Lose95/LoseNT software doesn't let you select the channel so it's probably not really meant to be changed.)
1999-05-06 16:32:45 +00:00
/*
* Read the default channel from the NIC. This may vary
* depending on the country where the NIC was purchased, so
* we can't hard-code a default and expect it to work for
* everyone.
update for new 802.11 support
2003-06-28 06:17:26 +00:00
*
* If no channel is specified, let the 802.11 code select.
Modify wicontrol(8) and wi(4) to allow setting the frequency of the WaveLAN's radio modem. The default is whatever the NIC uses since NICs sold in different countries may default to different frequencies. (The Lose95/LoseNT software doesn't let you select the channel so it's probably not really meant to be changed.)
1999-05-06 16:32:45 +00:00
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
buflen = sizeof(val);
update for new 802.11 support
2003-06-28 06:17:26 +00:00
if (wi_read_rid(sc, WI_RID_OWN_CHNL, &val, &buflen) == 0) {
val = le16toh(val);
KASSERT(val < IEEE80211_CHAN_MAX &&
ic->ic_channels[val].ic_flags != 0,
("wi_attach: invalid own channel %u!", val));
ic->ic_ibss_chan = &ic->ic_channels[val];
catch failure to fetch the card's "own channel"; this should not happen
2003-06-29 20:14:35 +00:00
} else {
device_printf(dev,
"WI_RID_OWN_CHNL failed, using first channel!\n");
ic->ic_ibss_chan = &ic->ic_channels[0];
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Modify wicontrol(8) and wi(4) to allow setting the frequency of the WaveLAN's radio modem. The default is whatever the NIC uses since NICs sold in different countries may default to different frequencies. (The Lose95/LoseNT software doesn't let you select the channel so it's probably not really meant to be changed.)
1999-05-06 16:32:45 +00:00
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
/*
* Set flags based on firmware version.
*/
switch (sc->sc_firmware_type) {
case WI_LUCENT:
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
sc->sc_ntxbuf = 1;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_flags |= WI_FLAGS_HAS_SYSSCALE;
#ifdef WI_HERMES_AUTOINC_WAR
/* XXX: not confirmed, but never seen for recent firmware */
if (sc->sc_sta_firmware_ver < 40000) {
sc->sc_flags |= WI_FLAGS_BUG_AUTOINC;
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#endif
if (sc->sc_sta_firmware_ver >= 60000)
sc->sc_flags |= WI_FLAGS_HAS_MOR;
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
if (sc->sc_sta_firmware_ver >= 60006) {
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_caps |= IEEE80211_C_IBSS;
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
ic->ic_caps |= IEEE80211_C_MONITOR;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_ibss_port = htole16(1);
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
sc->sc_min_rssi = WI_LUCENT_MIN_RSSI;
sc->sc_max_rssi = WI_LUCENT_MAX_RSSI;
sc->sc_dbm_offset = WI_LUCENT_DBM_OFFSET;
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
case WI_INTERSIL:
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
sc->sc_ntxbuf = WI_NTXBUF;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_flags |= WI_FLAGS_HAS_FRAGTHR;
sc->sc_flags |= WI_FLAGS_HAS_ROAMING;
sc->sc_flags |= WI_FLAGS_HAS_SYSSCALE;
Older versions of the intersil firmware is a lot slower than newer versions of the firmware. It responds more slowly to commands, and we bogusly failed them. We assume that all versions of the intersil firmware before 1.0 are 10 times slower and will give it 10x the time to finish. # for 5.2 we should always just assume 5s.
2003-12-09 07:41:07 +00:00
/*
* Old firmware are slow, so give peace a chance.
*/
if (sc->sc_sta_firmware_ver < 10000)
sc->wi_cmd_count = 5000;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_sta_firmware_ver > 10101)
sc->sc_flags |= WI_FLAGS_HAS_DBMADJUST;
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
if (sc->sc_sta_firmware_ver >= 800) {
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_caps |= IEEE80211_C_IBSS;
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
ic->ic_caps |= IEEE80211_C_MONITOR;
}
Restore a comment that was lost in the shuffle.
2003-01-16 23:38:08 +00:00
/*
* version 0.8.3 and newer are the only ones that are known
* to currently work. Earlier versions can be made to work,
* at least according to the Linux driver.
*/
Only INTERSIL 0.8.3 and newer firmware is supported with hostap mode. While earlier versions can be made to work, they require various work arounds not in the driver right now.
2002-07-26 22:54:30 +00:00
if (sc->sc_sta_firmware_ver >= 803)
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_caps |= IEEE80211_C_HOSTAP;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_ibss_port = htole16(0);
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
sc->sc_min_rssi = WI_PRISM_MIN_RSSI;
sc->sc_max_rssi = WI_PRISM_MAX_RSSI;
sc->sc_dbm_offset = WI_PRISM_DBM_OFFSET;
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
case WI_SYMBOL:
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
sc->sc_ntxbuf = 1;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_flags |= WI_FLAGS_HAS_DIVERSITY;
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
if (sc->sc_sta_firmware_ver >= 25000)
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_caps |= IEEE80211_C_IBSS;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_ibss_port = htole16(4);
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
sc->sc_min_rssi = WI_PRISM_MIN_RSSI;
sc->sc_max_rssi = WI_PRISM_MAX_RSSI;
sc->sc_dbm_offset = WI_PRISM_DBM_OFFSET;
Add better mediaopt support for ibss and friends. Now the driver is closer to matching the wi man page. Submitted by: jhay (who obtained it from OpenBSD).
2002-06-19 17:37:34 +00:00
break;
}
Add support for WEP (encryption) for silver and gold WaveLAN/IEEE turbo cards. Also update wicontrol to enable/disable encryption, set WEP keys and set the TX key index. Silver cards only have 40-bit keys. This is something of a quick hack, but it works well enough for me to commit this from the LinuxWorld exhibit floor. The WEP support only shows up if you have a card that supports it. Would have been approved by: jkh, if he hadn't wandered off somewhere Approved in his place by: msmith, who's standing right here
2000-02-02 17:59:13 +00:00
/*
* Find out if we support WEP on this card.
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
buflen = sizeof(val);
if (wi_read_rid(sc, WI_RID_WEP_AVAIL, &val, &buflen) == 0 &&
val != htole16(0))
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_caps |= IEEE80211_C_WEP;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Find supported rates. */
buflen = sizeof(ratebuf);
update for new 802.11 support
2003-06-28 06:17:26 +00:00
rs = &ic->ic_sup_rates[IEEE80211_MODE_11B];
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (wi_read_rid(sc, WI_RID_DATA_RATES, ratebuf, &buflen) == 0) {
update for new 802.11 support
2003-06-28 06:17:26 +00:00
nrates = le16toh(*(u_int16_t *)ratebuf);
if (nrates > IEEE80211_RATE_MAXSIZE)
nrates = IEEE80211_RATE_MAXSIZE;
rs->rs_nrates = 0;
for (i = 0; i < nrates; i++)
if (ratebuf[2+i])
rs->rs_rates[rs->rs_nrates++] = ratebuf[2+i];
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
} else {
/* XXX fallback on error? */
update for new 802.11 support
2003-06-28 06:17:26 +00:00
rs->rs_nrates = 0;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Add support for WEP (encryption) for silver and gold WaveLAN/IEEE turbo cards. Also update wicontrol to enable/disable encryption, set WEP keys and set the TX key index. Silver cards only have 40-bit keys. This is something of a quick hack, but it works well enough for me to commit this from the LinuxWorld exhibit floor. The WEP support only shows up if you have a card that supports it. Would have been approved by: jkh, if he hadn't wandered off somewhere Approved in his place by: msmith, who's standing right here
2000-02-02 17:59:13 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
buflen = sizeof(val);
if ((sc->sc_flags & WI_FLAGS_HAS_DBMADJUST) &&
wi_read_rid(sc, WI_RID_DBM_ADJUST, &val, &buflen) == 0) {
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
sc->sc_dbm_offset = le16toh(val);
}
Apply some contributed patches to reduce number of tx buffer allocation failures and add some support for WEP on Prism II chip. Submitted by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
2000-12-15 23:34:13 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_max_datalen = 2304;
sc->sc_system_scale = 1;
sc->sc_cnfauthmode = IEEE80211_AUTH_OPEN;
sc->sc_roaming_mode = 1;
sc->sc_portnum = WI_DEFAULT_PORT;
sc->sc_authtype = WI_DEFAULT_AUTHTYPE;
bzero(sc->sc_nodename, sizeof(sc->sc_nodename));
sc->sc_nodelen = sizeof(WI_DEFAULT_NODENAME) - 1;
bcopy(WI_DEFAULT_NODENAME, sc->sc_nodename, sc->sc_nodelen);
bzero(sc->sc_net_name, sizeof(sc->sc_net_name));
bcopy(WI_DEFAULT_NETNAME, sc->sc_net_name,
sizeof(WI_DEFAULT_NETNAME) - 1);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
/*
Make all Ethernet drivers attach using ether_ifattach() and detach using ether_ifdetach(). The former consolidates the operations of if_attach(), ng_ether_attach(), and bpfattach(). The latter consolidates the corresponding detach operations. Reviewed by: julian, freebsd-net
2000-07-13 22:54:34 +00:00
* Call MI attach routine.
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
*/
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ieee80211_ifattach(ic);
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
/* override state transition method */
sc->sc_newstate = ic->ic_newstate;
ic->ic_newstate = wi_newstate;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ieee80211_media_init(ic, wi_media_change, wi_media_status);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
#if NBPFILTER > 0
bpfattach2(ifp, DLT_IEEE802_11_RADIO,
sizeof(struct ieee80211_frame) + sizeof(sc->sc_tx_th),
&sc->sc_drvbpf);
/*
* Initialize constant fields.
radiotap updates: o force little-endian byte order for header o pad header to 32-bit boundary to guard against applications that assume packet data alignment
2004-04-01 00:38:45 +00:00
* XXX make header lengths a multiple of 32-bits so subsequent
* headers are properly aligned; this is a kludge to keep
* certain applications happy.
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
*
* NB: the channel is setup each time we transition to the
* RUN state to avoid filling it in for each frame.
*/
radiotap updates: o force little-endian byte order for header o pad header to 32-bit boundary to guard against applications that assume packet data alignment
2004-04-01 00:38:45 +00:00
sc->sc_tx_th_len = roundup(sizeof(sc->sc_tx_th), sizeof(u_int32_t));
sc->sc_tx_th.wt_ihdr.it_len = htole16(sc->sc_tx_th_len);
sc->sc_tx_th.wt_ihdr.it_present = htole32(WI_TX_RADIOTAP_PRESENT);
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
radiotap updates: o force little-endian byte order for header o pad header to 32-bit boundary to guard against applications that assume packet data alignment
2004-04-01 00:38:45 +00:00
sc->sc_rx_th_len = roundup(sizeof(sc->sc_rx_th), sizeof(u_int32_t));
sc->sc_rx_th.wr_ihdr.it_len = htole16(sc->sc_rx_th_len);
sc->sc_rx_th.wr_ihdr.it_present = htole32(WI_RX_RADIOTAP_PRESENT);
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
#endif
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (bootverbose)
ieee80211_announce(ic);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return (0);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int
wi_detach(device_t dev)
Implement prism2 detection from NetBSD. This mostly obsoletes the prism2 flag in pccard.conf, but I'm leaving it place for the moment in case the small sample of PrismII cards that I've tried is not representative. MFC After: 30 days Obtained from: NetBSD
2001-12-05 08:57:36 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = device_get_softc(dev);
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK_DECL();
Implement prism2 detection from NetBSD. This mostly obsoletes the prism2 flag in pccard.conf, but I'm leaving it place for the moment in case the small sample of PrismII cards that I've tried is not representative. MFC After: 30 days Obtained from: NetBSD
2001-12-05 08:57:36 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK(sc);
Four fixes from NetBSD: 1) Properly detect the Symbol based cards (The 3Com Airconnect and their ilk) and only reset them *ONCE* ever. This appears to make them work, but more testing is needed. The tests that would wedge up my machine completely now appear to work, but I have not real access points handy. 2) Report both the Station firmware and the Primary firmware on Prism based cards. On Lucent based cards, only report the station firmware since that's all it supports. On symbol cards, report the symbol specific firmware name as its station firmware. 3) Better Prism 2.5 and 3 family names. We really need to go table driven for this. 4) Workaround for bugs in Intersil's firmware is only needed for at most 0.8.2 and earlier, since 0.8.3 and later appear to work. Obtained from: NetBSD
2002-04-03 19:44:17 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* check if device was removed */
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
sc->wi_gone |= !bus_child_present(dev);
Implement prism2 detection from NetBSD. This mostly obsoletes the prism2 flag in pccard.conf, but I'm leaving it place for the moment in case the small sample of PrismII cards that I've tried is not representative. MFC After: 30 days Obtained from: NetBSD
2001-12-05 08:57:36 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_stop(ifp, 0);
Four fixes from NetBSD: 1) Properly detect the Symbol based cards (The 3Com Airconnect and their ilk) and only reset them *ONCE* ever. This appears to make them work, but more testing is needed. The tests that would wedge up my machine completely now appear to work, but I have not real access points handy. 2) Report both the Station firmware and the Primary firmware on Prism based cards. On Lucent based cards, only report the station firmware since that's all it supports. On symbol cards, report the symbol specific firmware name as its station firmware. 3) Better Prism 2.5 and 3 family names. We really need to go table driven for this. 4) Workaround for bugs in Intersil's firmware is only needed for at most 0.8.2 and earlier, since 0.8.3 and later appear to work. Obtained from: NetBSD
2002-04-03 19:44:17 +00:00
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
#if NBPFILTER > 0
bpfdetach(ifp);
#endif
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ieee80211_ifdetach(&sc->sc_ic);
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
if_free(sc->sc_ifp);
Don't hold a driver lock across bus_teardown_intr. Jhb points out that one cannot generally hold a lock and call bus_teardown_intr. This is race free with wi_intr because bus_teardown_intr won't allow wi_intr to be called after it returns. # jeff hsu points out that there might be a race between this unlock # and wi_start. While that may be true also, it won't impact this commit. Submitted by: jhb
2003-04-29 03:22:39 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
bus_teardown_intr(dev, sc->irq, sc->wi_intrhand);
wi_free(dev);
#if __FreeBSD_version >= 500000
mtx_destroy(&sc->sc_mtx);
#endif
return (0);
Implement prism2 detection from NetBSD. This mostly obsoletes the prism2 flag in pccard.conf, but I'm leaving it place for the moment in case the small sample of PrismII cards that I've tried is not representative. MFC After: 30 days Obtained from: NetBSD
2001-12-05 08:57:36 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#ifdef __NetBSD__
int
wi_activate(struct device *self, enum devact act)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = (struct wi_softc *)self;
int rv = 0, s;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
s = splnet();
switch (act) {
case DVACT_ACTIVATE:
rv = EOPNOTSUPP;
break;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case DVACT_DEACTIVATE:
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
if_deactivate(sc->sc_ifp);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
}
splx(s);
return rv;
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
void
wi_power(struct wi_softc *sc, int why)
{
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int s;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
s = splnet();
switch (why) {
case PWR_SUSPEND:
case PWR_STANDBY:
wi_stop(ifp, 1);
break;
case PWR_RESUME:
if (ifp->if_flags & IFF_UP) {
wi_init(ifp);
(void)wi_intr(sc);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
case PWR_SOFTSUSPEND:
case PWR_SOFTSTANDBY:
case PWR_SOFTRESUME:
break;
}
splx(s);
}
#endif /* __NetBSD__ */
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
void
wi_shutdown(device_t dev)
{
struct wi_softc *sc = device_get_softc(dev);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
wi_stop(sc->sc_ifp, 1);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
void
wi_intr(void *arg)
{
struct wi_softc *sc = arg;
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
u_int16_t status;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK_DECL();
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK(sc);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
if (sc->wi_gone || !sc->sc_enabled || (ifp->if_flags & IFF_UP) == 0) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
CSR_WRITE_2(sc, WI_INT_EN, 0);
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
CSR_WRITE_2(sc, WI_EVENT_ACK, 0xFFFF);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_UNLOCK(sc);
return;
}
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
/* Disable interrupts. */
CSR_WRITE_2(sc, WI_INT_EN, 0);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
status = CSR_READ_2(sc, WI_EVENT_STAT);
if (status & WI_EV_RX)
wi_rx_intr(sc);
if (status & WI_EV_ALLOC)
wi_tx_intr(sc);
if (status & WI_EV_TX_EXC)
wi_tx_ex_intr(sc);
if (status & WI_EV_INFO)
wi_info_intr(sc);
if ((ifp->if_flags & IFF_OACTIVE) == 0 &&
(sc->sc_flags & WI_FLAGS_OUTRANGE) == 0 &&
Second part of ALTQ driver modifications, covering: an(4), ath(4), hme(4), ndis(4), vr(4) and wi(4) Please help testing: http://people.freebsd.org/~mlaier/ALTQ_driver/ Tested by: Vaidas Damosevicius (an, ath, wi) Roman Divacky (vr) Submitted by: yongari (hme)
2004-08-01 23:58:04 +00:00
!IFQ_DRV_IS_EMPTY(&ifp->if_snd))
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
wi_start(ifp);
/* Re-enable interrupts. */
CSR_WRITE_2(sc, WI_INT_EN, WI_INTRS);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_UNLOCK(sc);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return;
}
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
void
wi_init(void *arg)
{
struct wi_softc *sc = arg;
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct ieee80211com *ic = &sc->sc_ic;
struct wi_joinreq join;
int i;
int error = 0, wasenabled;
struct ifaddr *ifa;
struct sockaddr_dl *sdl;
WI_LOCK_DECL();
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK(sc);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->wi_gone) {
WI_UNLOCK(sc);
return;
}
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
Move symbol reset detection code back into wi_reset. This is a more reliable way to detect if the symbol cards have been reset or not. This makes symbol cards work better. Submitted by: deischen
2003-03-18 02:54:39 +00:00
if ((wasenabled = sc->sc_enabled))
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
wi_stop(ifp, 1);
Move symbol reset detection code back into wi_reset. This is a more reliable way to detect if the symbol cards have been reset or not. This makes symbol cards work better. Submitted by: deischen
2003-03-18 02:54:39 +00:00
wi_reset(sc);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* common 802.11 configuration */
ic->ic_flags &= ~IEEE80211_F_IBSSON;
sc->sc_flags &= ~WI_FLAGS_OUTRANGE;
switch (ic->ic_opmode) {
case IEEE80211_M_STA:
wi_write_val(sc, WI_RID_PORTTYPE, WI_PORTTYPE_BSS);
break;
case IEEE80211_M_IBSS:
wi_write_val(sc, WI_RID_PORTTYPE, sc->sc_ibss_port);
ic->ic_flags |= IEEE80211_F_IBSSON;
break;
case IEEE80211_M_AHDEMO:
wi_write_val(sc, WI_RID_PORTTYPE, WI_PORTTYPE_ADHOC);
break;
case IEEE80211_M_HOSTAP:
Truly fix the lockup mentioned in 1.153. The PRISM hardware is not capable of functioning in HostAP mode with a zero-length SSID, so use " " if one is not set.
2003-11-04 23:47:19 +00:00
/*
* For PRISM cards, override the empty SSID, because in
* HostAP mode the controller will lock up otherwise.
*/
if (sc->sc_firmware_type == WI_INTERSIL &&
ic->ic_des_esslen == 0) {
ic->ic_des_essid[0] = ' ';
ic->ic_des_esslen = 1;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_write_val(sc, WI_RID_PORTTYPE, WI_PORTTYPE_HOSTAP);
break;
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
case IEEE80211_M_MONITOR:
if (sc->sc_firmware_type == WI_LUCENT)
wi_write_val(sc, WI_RID_PORTTYPE, WI_PORTTYPE_ADHOC);
wi_cmd(sc, WI_CMD_DEBUG | (WI_TEST_MONITOR << 8), 0, 0, 0);
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Intersil interprets this RID as joining ESS even in IBSS mode */
if (sc->sc_firmware_type == WI_LUCENT &&
(ic->ic_flags & IEEE80211_F_IBSSON) && ic->ic_des_esslen > 0)
wi_write_val(sc, WI_RID_CREATE_IBSS, 1);
else
wi_write_val(sc, WI_RID_CREATE_IBSS, 0);
wi_write_val(sc, WI_RID_MAX_SLEEP, ic->ic_lintval);
wi_write_ssid(sc, WI_RID_DESIRED_SSID, ic->ic_des_essid,
ic->ic_des_esslen);
update for new 802.11 support
2003-06-28 06:17:26 +00:00
wi_write_val(sc, WI_RID_OWN_CHNL,
ieee80211_chan2ieee(ic, ic->ic_ibss_chan));
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_write_ssid(sc, WI_RID_OWN_SSID, ic->ic_des_essid, ic->ic_des_esslen);
ifa = ifaddr_byindex(ifp->if_index);
sdl = (struct sockaddr_dl *) ifa->ifa_addr;
IEEE80211_ADDR_COPY(ic->ic_myaddr, LLADDR(sdl));
wi_write_rid(sc, WI_RID_MAC_NODE, ic->ic_myaddr, IEEE80211_ADDR_LEN);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (ic->ic_caps & IEEE80211_C_PMGT)
wi_write_val(sc, WI_RID_PM_ENABLED,
(ic->ic_flags & IEEE80211_F_PMGTON) ? 1 : 0);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* not yet common 802.11 configuration */
wi_write_val(sc, WI_RID_MAX_DATALEN, sc->sc_max_datalen);
update for new 802.11 support
2003-06-28 06:17:26 +00:00
wi_write_val(sc, WI_RID_RTS_THRESH, ic->ic_rtsthreshold);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_flags & WI_FLAGS_HAS_FRAGTHR)
update for new 802.11 support
2003-06-28 06:17:26 +00:00
wi_write_val(sc, WI_RID_FRAG_THRESH, ic->ic_fragthreshold);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* driver specific 802.11 configuration */
if (sc->sc_flags & WI_FLAGS_HAS_SYSSCALE)
wi_write_val(sc, WI_RID_SYSTEM_SCALE, sc->sc_system_scale);
if (sc->sc_flags & WI_FLAGS_HAS_ROAMING)
wi_write_val(sc, WI_RID_ROAMING_MODE, sc->sc_roaming_mode);
if (sc->sc_flags & WI_FLAGS_HAS_MOR)
wi_write_val(sc, WI_RID_MICROWAVE_OVEN, sc->sc_microwave_oven);
wi_write_txrate(sc);
wi_write_ssid(sc, WI_RID_NODENAME, sc->sc_nodename, sc->sc_nodelen);
if (ic->ic_opmode == IEEE80211_M_HOSTAP &&
sc->sc_firmware_type == WI_INTERSIL) {
wi_write_val(sc, WI_RID_OWN_BEACON_INT, ic->ic_lintval);
wi_write_val(sc, WI_RID_BASIC_RATE, 0x03); /* 1, 2 */
wi_write_val(sc, WI_RID_SUPPORT_RATE, 0x0f); /* 1, 2, 5.5, 11 */
wi_write_val(sc, WI_RID_DTIM_PERIOD, 1);
}
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/*
* Initialize promisc mode.
* Being in the Host-AP mode causes a great
* deal of pain if primisc mode is set.
* Therefore we avoid confusing the firmware
* and always reset promisc mode in Host-AP
* mode. Host-AP sees all the packets anyway.
*/
if (ic->ic_opmode != IEEE80211_M_HOSTAP &&
(ifp->if_flags & IFF_PROMISC) != 0) {
wi_write_val(sc, WI_RID_PROMISC, 1);
} else {
wi_write_val(sc, WI_RID_PROMISC, 0);
}
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Configure WEP. */
Honouring current authmode setting. With this patch, my wi card can now associate to an AP which uses shared WEP key authentication. Tested with: "ifconfig wi0 authmode shared" Reviewed by: imp, sam
2005-06-02 01:51:16 +00:00
if (ic->ic_caps & IEEE80211_C_WEP) {
sc->sc_cnfauthmode = ic->ic_bss->ni_authmode;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_write_wep(sc);
Honouring current authmode setting. With this patch, my wi card can now associate to an AP which uses shared WEP key authentication. Tested with: "ifconfig wi0 authmode shared" Reviewed by: imp, sam
2005-06-02 01:51:16 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Set multicast filter. */
wi_write_multi(sc);
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
/* Allocate fids for the card */
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_firmware_type != WI_SYMBOL || !wasenabled) {
sc->sc_buflen = IEEE80211_MAX_LEN + sizeof(struct wi_frame);
if (sc->sc_firmware_type == WI_SYMBOL)
sc->sc_buflen = 1585; /* XXX */
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
for (i = 0; i < sc->sc_ntxbuf; i++) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_alloc_fid(sc, sc->sc_buflen,
&sc->sc_txd[i].d_fid);
if (error) {
device_printf(sc->sc_dev,
"tx buffer allocation failed (error %u)\n",
error);
goto out;
}
sc->sc_txd[i].d_len = 0;
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
}
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_txcur = sc->sc_txnext = 0;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Enable desired port */
wi_cmd(sc, WI_CMD_ENABLE | sc->sc_portnum, 0, 0, 0);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
sc->sc_enabled = 1;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ifp->if_flags |= IFF_RUNNING;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
ifp->if_flags &= ~IFF_OACTIVE;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (ic->ic_opmode == IEEE80211_M_AHDEMO ||
Eliminate some of the egregious bypass of the 802.11 state machine; instead use the intended entry points. There's still too much incestuous knowledge about the internals of the 802.11 layer but this at least fixes adhoc mode.
2005-01-01 17:45:11 +00:00
ic->ic_opmode == IEEE80211_M_IBSS ||
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
ic->ic_opmode == IEEE80211_M_MONITOR ||
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ic->ic_opmode == IEEE80211_M_HOSTAP)
Eliminate some of the egregious bypass of the 802.11 state machine; instead use the intended entry points. There's still too much incestuous knowledge about the internals of the 802.11 layer but this at least fixes adhoc mode.
2005-01-01 17:45:11 +00:00
ieee80211_create_ibss(ic, ic->ic_ibss_chan);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Enable interrupts */
CSR_WRITE_2(sc, WI_INT_EN, WI_INTRS);
if (!wasenabled &&
ic->ic_opmode == IEEE80211_M_HOSTAP &&
sc->sc_firmware_type == WI_INTERSIL) {
/* XXX: some card need to be re-enabled for hostap */
wi_cmd(sc, WI_CMD_DISABLE | WI_PORT0, 0, 0, 0);
wi_cmd(sc, WI_CMD_ENABLE | WI_PORT0, 0, 0, 0);
}
if (ic->ic_opmode == IEEE80211_M_STA &&
((ic->ic_flags & IEEE80211_F_DESBSSID) ||
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_des_chan != IEEE80211_CHAN_ANYC)) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
memset(&join, 0, sizeof(join));
if (ic->ic_flags & IEEE80211_F_DESBSSID)
IEEE80211_ADDR_COPY(&join.wi_bssid, ic->ic_des_bssid);
update for new 802.11 support
2003-06-28 06:17:26 +00:00
if (ic->ic_des_chan != IEEE80211_CHAN_ANYC)
join.wi_chan = htole16(
ieee80211_chan2ieee(ic, ic->ic_des_chan));
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Lucent firmware does not support the JOIN RID. */
if (sc->sc_firmware_type != WI_LUCENT)
wi_write_rid(sc, WI_RID_JOIN_REQ, &join, sizeof(join));
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_UNLOCK(sc);
return;
out:
if (error) {
if_printf(ifp, "interface not running\n");
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
wi_stop(ifp, 1);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Unlock the mutex in the error case in wi_init. Otherwise we can return from an ioctl with the lock held. Submitted by: iedowse (by way of sam)
2003-02-02 06:35:46 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
DPRINTF(("wi_init: return %d\n", error));
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
return;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
void
wi_stop(struct ifnet *ifp, int disable)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = ifp->if_softc;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
struct ieee80211com *ic = &sc->sc_ic;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK_DECL();
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK(sc);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
DELAY(100000);
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
ieee80211_new_state(ic, IEEE80211_S_INIT, -1);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_enabled && !sc->wi_gone) {
CSR_WRITE_2(sc, WI_INT_EN, 0);
wi_cmd(sc, WI_CMD_DISABLE | sc->sc_portnum, 0, 0, 0);
if (disable) {
#ifdef __NetBSD__
if (sc->sc_disable)
(*sc->sc_disable)(sc);
#endif
update for new 802.11 support
2003-06-28 06:17:26 +00:00
sc->sc_enabled = 0;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
} else if (sc->wi_gone && disable) /* gone --> not enabled */
sc->sc_enabled = 0;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_tx_timer = 0;
sc->sc_scan_timer = 0;
sc->sc_false_syns = 0;
sc->sc_naps = 0;
ifp->if_flags &= ~(IFF_OACTIVE | IFF_RUNNING);
ifp->if_timer = 0;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_UNLOCK(sc);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
o Comment out the symbol download code for 4.x. o Add hooks for doing power management of the output signal. o Minor hacks to make flexlint happy wrt staticness of functions.
2002-10-14 01:59:57 +00:00
static void
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_start(struct ifnet *ifp)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = ifp->if_softc;
struct ieee80211com *ic = &sc->sc_ic;
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
struct ieee80211_node *ni;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct ieee80211_frame *wh;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
struct ether_header *eh;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct mbuf *m0;
struct wi_frame frmhdr;
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
int cur, fid, off, error;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK_DECL();
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_LOCK(sc);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->wi_gone) {
WI_UNLOCK(sc);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
return;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_flags & WI_FLAGS_OUTRANGE) {
WI_UNLOCK(sc);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
return;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
memset(&frmhdr, 0, sizeof(frmhdr));
cur = sc->sc_txnext;
for (;;) {
IF_POLL(&ic->ic_mgtq, m0);
if (m0 != NULL) {
if (sc->sc_txd[cur].d_len != 0) {
ifp->if_flags |= IFF_OACTIVE;
break;
}
IF_DEQUEUE(&ic->ic_mgtq, m0);
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
/*
* Hack! The referenced node pointer is in the
* rcvif field of the packet header. This is
* placed there by ieee80211_mgmt_output because
* we need to hold the reference with the frame
* and there's no other way (other than packet
* tags which we consider too expensive to use)
* to pass it along.
*/
ni = (struct ieee80211_node *) m0->m_pkthdr.rcvif;
m0->m_pkthdr.rcvif = NULL;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
m_copydata(m0, 4, ETHER_ADDR_LEN * 2,
(caddr_t)&frmhdr.wi_ehdr);
frmhdr.wi_ehdr.ether_type = 0;
wh = mtod(m0, struct ieee80211_frame *);
} else {
if (ic->ic_state != IEEE80211_S_RUN)
break;
Second part of ALTQ driver modifications, covering: an(4), ath(4), hme(4), ndis(4), vr(4) and wi(4) Please help testing: http://people.freebsd.org/~mlaier/ALTQ_driver/ Tested by: Vaidas Damosevicius (an, ath, wi) Roman Divacky (vr) Submitted by: yongari (hme)
2004-08-01 23:58:04 +00:00
IFQ_DRV_DEQUEUE(&ifp->if_snd, m0);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (m0 == NULL)
break;
if (sc->sc_txd[cur].d_len != 0) {
Second part of ALTQ driver modifications, covering: an(4), ath(4), hme(4), ndis(4), vr(4) and wi(4) Please help testing: http://people.freebsd.org/~mlaier/ALTQ_driver/ Tested by: Vaidas Damosevicius (an, ath, wi) Roman Divacky (vr) Submitted by: yongari (hme)
2004-08-01 23:58:04 +00:00
IFQ_DRV_PREPEND(&ifp->if_snd, m0);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ifp->if_flags |= IFF_OACTIVE;
break;
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (m0->m_len < sizeof(struct ether_header) &&
(m0 = m_pullup(m0, sizeof(struct ether_header))) == NULL) {
ifp->if_oerrors++;
continue;
}
eh = mtod(m0, struct ether_header *);
ni = ieee80211_find_txnode(ic, eh->ether_dhost);
if (ni == NULL) {
m_freem(m0);
continue;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ifp->if_opackets++;
m_copydata(m0, 0, ETHER_HDR_LEN,
(caddr_t)&frmhdr.wi_ehdr);
#if NBPFILTER > 0
BPF_MTAP(ifp, m0);
#endif
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
m0 = ieee80211_encap(ic, m0, ni);
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
if (m0 == NULL) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ifp->if_oerrors++;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ieee80211_free_node(ni);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
continue;
}
wh = mtod(m0, struct ieee80211_frame *);
}
#if NBPFILTER > 0
if (ic->ic_rawbpf)
bpf_mtap(ic->ic_rawbpf, m0);
#endif
frmhdr.wi_tx_ctl = htole16(WI_ENC_TX_802_11|WI_TXCNTL_TX_EX);
Fix wep operation for station mode: o don't encapsulate on tx; the chip expect a raw frame w/o the crypto header o clear the WEP bit in the 802.11 header on rx so the 802.11 layer doesn't try to strip the crypto header o clobber the "drop unencoded frames" state bit when privacy is enabled so rx'd frames we pass up to the 802.11 layer are not discarded as unencrypted This stuff will need to be redone if anyone decides to add WPA support.
2004-12-17 03:57:16 +00:00
/* XXX check key for SWCRYPT instead of using operating mode */
if (ic->ic_opmode == IEEE80211_M_HOSTAP &&
(wh->i_fc[1] & IEEE80211_FC1_WEP)) {
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
struct ieee80211_key *k;
k = ieee80211_crypto_encap(ic, ni, m0);
if (k == NULL) {
if (ni != NULL)
ieee80211_free_node(ni);
reclaim mbuf chain when ieee80211_crypto_encap fails Noticed by: David Young
2005-03-08 17:01:03 +00:00
m_freem(m0);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
continue;
}
Fix wep operation for station mode: o don't encapsulate on tx; the chip expect a raw frame w/o the crypto header o clear the WEP bit in the 802.11 header on rx so the 802.11 layer doesn't try to strip the crypto header o clobber the "drop unencoded frames" state bit when privacy is enabled so rx'd frames we pass up to the 802.11 layer are not discarded as unencrypted This stuff will need to be redone if anyone decides to add WPA support.
2004-12-17 03:57:16 +00:00
frmhdr.wi_tx_ctl |= htole16(WI_TXCNTL_NOCRYPT);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
#if NBPFILTER > 0
if (sc->sc_drvbpf) {
update radiotap support to reflect recent changes: o add xmit rate o drop rx time o add rx flags
2003-12-28 06:58:52 +00:00
sc->sc_tx_th.wt_rate =
ni->ni_rates.rs_rates[ni->ni_txrate];
o eliminate widespread on-stack mbuf use for bpf by introducing a new bpf_mtap2 routine that does the right thing for an mbuf and a variable-length chunk of data that should be prepended. o while we're sweeping the drivers, use u_int32_t uniformly when when prepending the address family (several places were assuming sizeof(int) was 4) o return M_ASSERTVALID to BPF_MTAP* now that all stack-allocated mbufs have been eliminated; this may better be moved to the bpf routines Reviewed by: arch@ and several others
2003-12-28 03:56:00 +00:00
bpf_mtap2(sc->sc_drvbpf,
radiotap updates: o force little-endian byte order for header o pad header to 32-bit boundary to guard against applications that assume packet data alignment
2004-04-01 00:38:45 +00:00
&sc->sc_tx_th, sc->sc_tx_th_len, m0);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
#endif
correct xmit-side radiotap collection by tap'ing the frame before prepending the h/w header
2004-04-01 00:33:33 +00:00
m_copydata(m0, 0, sizeof(struct ieee80211_frame),
(caddr_t)&frmhdr.wi_whdr);
m_adj(m0, sizeof(struct ieee80211_frame));
frmhdr.wi_dat_len = htole16(m0->m_pkthdr.len);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (IFF_DUMPPKTS(ifp))
update for new 802.11 support
2003-06-28 06:17:26 +00:00
wi_dump_pkt(&frmhdr, NULL, -1);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
fid = sc->sc_txd[cur].d_fid;
off = sizeof(frmhdr);
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
error = wi_write_bap(sc, fid, 0, &frmhdr, sizeof(frmhdr)) != 0
|| wi_mwrite_bap(sc, fid, off, m0, m0->m_pkthdr.len) != 0;
m_freem(m0);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (ni != NULL)
ieee80211_free_node(ni);
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
if (error) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ifp->if_oerrors++;
continue;
}
sc->sc_txd[cur].d_len = off;
if (sc->sc_txcur == cur) {
if (wi_cmd(sc, WI_CMD_TX | WI_RECLAIM, fid, 0, 0)) {
if_printf(ifp, "xmit failed\n");
sc->sc_txd[cur].d_len = 0;
continue;
}
sc->sc_tx_timer = 5;
ifp->if_timer = 1;
}
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
sc->sc_txnext = cur = (cur + 1) % sc->sc_ntxbuf;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
WI_UNLOCK(sc);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_reset(struct wi_softc *sc)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
#define WI_INIT_TRIES 3
int i;
Initialize error.
2003-04-27 23:44:05 +00:00
int error = 0;
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
int tries;
/* Symbol firmware cannot be initialized more than once */
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
if (sc->sc_firmware_type == WI_SYMBOL && sc->sc_reset)
Move symbol reset detection code back into wi_reset. This is a more reliable way to detect if the symbol cards have been reset or not. This makes symbol cards work better. Submitted by: deischen
2003-03-18 02:54:39 +00:00
return (0);
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
if (sc->sc_firmware_type == WI_SYMBOL)
tries = 1;
else
tries = WI_INIT_TRIES;
Move symbol reset detection code back into wi_reset. This is a more reliable way to detect if the symbol cards have been reset or not. This makes symbol cards work better. Submitted by: deischen
2003-03-18 02:54:39 +00:00
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
for (i = 0; i < tries; i++) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if ((error = wi_cmd(sc, WI_CMD_INI, 0, 0, 0)) == 0)
break;
DELAY(WI_DELAY * 1000);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
sc->sc_reset = 1;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
if (i == tries) {
if_printf(ifp, "init failed\n");
return (error);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
CSR_WRITE_2(sc, WI_INT_EN, 0);
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
CSR_WRITE_2(sc, WI_EVENT_ACK, 0xFFFF);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Calibrate timer. */
Make 2/3 of my symbol cards work again. The 3rd symbol card card has firmware 1.50.12, but 2.20.1 and 3.10.4 work. The 1.50.12 card gets past doing dhclient, but hangs on transmit a little after the ip address is set. The 1.50.12 card has always been 'cranky' and Bill Paul's tearing it apart at FreeBSD '99 hasn't helped. sc_reset and sc_enable are subtlely different things. sc_reset means exactly "WI_CMD_INI has happened." sc_enabled means "WI_CMD_ENABLE has been sent to the card without a WI_CMD_DISABLE following." This is a little different than what they mean on NetBSD (where both of these concepts are comingled). NetBSD will try to only enable symbol cards once, while FreeBSD only sends the WI_CMD_INI once. Also, only try once to reset the card on a symbol. This makes the lucent cards no worse than before, but apparently not much better either. I got fewer hangs in my testing than I have in the past, but I don't know if it is statistically significant or not.
2003-04-27 15:56:05 +00:00
wi_write_val(sc, WI_RID_TICK_TIME, 8);
return (0);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#undef WI_INIT_TRIES
}
Add more diagnostic output for failure. s/1518/ETHER_MAX_LEN Some style changes, add some braces, mostly residual from having a lot of debug hooks added while working on this driver. Bring in a plethora of changes from NetBSD: revision 1.58 date: 2001/03/08 11:07:08; author: ichiro; state: Exp; lines: +17 -1 it wait until busy flag disappears. it was able to prevent some cards with late initializing faling in wi_reset(). revision 1.41 date: 2000/10/13 19:15:08; author: jonathan; state: Exp; lines: +4 -2 Fix wi_intr() to avoid touching card registers during insert/remove events, when sharing an interrupt with other devices: check sc->sc_enabled, and drop the interrupt if its' off. revision 1.30 date: 2000/08/18 04:11:48; author: jhawk; state: Exp; lines: +4 -4 Copy wi_{dst,src}_addr from struct wi_frame into faked-up ether_header instead of addr1 and addr2. THis means that tcpdump -e will show the correct MAC address for communications with access points instead of showing the BSSID. In the future there should be 802.11 support for bpf/libpcap/tcpdump, but that is aways down the road.
2001-04-10 05:29:26 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void
wi_watchdog(struct ifnet *ifp)
{
struct wi_softc *sc = ifp->if_softc;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ifp->if_timer = 0;
if (!sc->sc_enabled)
return;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_tx_timer) {
if (--sc->sc_tx_timer == 0) {
if_printf(ifp, "device timeout\n");
ifp->if_oerrors++;
wi_init(ifp->if_softc);
return;
}
ifp->if_timer = 1;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_scan_timer) {
if (--sc->sc_scan_timer <= WI_SCAN_WAIT - WI_SCAN_INQWAIT &&
sc->sc_firmware_type == WI_INTERSIL) {
DPRINTF(("wi_watchdog: inquire scan\n"));
wi_cmd(sc, WI_CMD_INQUIRE, WI_INFO_SCAN_RESULTS, 0, 0);
}
if (sc->sc_scan_timer)
ifp->if_timer = 1;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* TODO: rate control */
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ieee80211_watchdog(&sc->sc_ic);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
put function return types on a line by themselves as per style(9)
2001-12-27 20:12:03 +00:00
static int
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_ioctl(struct ifnet *ifp, u_long cmd, caddr_t data)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = ifp->if_softc;
struct ieee80211com *ic = &sc->sc_ic;
struct ifreq *ifr = (struct ifreq *)data;
struct ieee80211req *ireq;
u_int8_t nodename[IEEE80211_NWID_LEN];
int error = 0;
#if __FreeBSD_version >= 500000
struct thread *td = curthread;
#else
struct proc *td = curproc; /* Little white lie */
#endif
struct wi_req wreq;
WI_LOCK_DECL();
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (sc->wi_gone)
return (ENODEV);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (cmd) {
case SIOCSIFFLAGS:
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
/*
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
* Can't do promisc and hostap at the same time. If all that's
* changing is the promisc flag, try to short-circuit a call to
* wi_init() by just setting PROMISC in the hardware.
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
*/
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (ifp->if_flags & IFF_UP) {
if (ic->ic_opmode != IEEE80211_M_HOSTAP &&
ifp->if_flags & IFF_RUNNING) {
if (ifp->if_flags & IFF_PROMISC &&
!(sc->sc_if_flags & IFF_PROMISC)) {
wi_write_val(sc, WI_RID_PROMISC, 1);
} else if (!(ifp->if_flags & IFF_PROMISC) &&
sc->sc_if_flags & IFF_PROMISC) {
wi_write_val(sc, WI_RID_PROMISC, 0);
} else {
wi_init(sc);
}
} else {
wi_init(sc);
}
} else {
if (ifp->if_flags & IFF_RUNNING) {
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
wi_stop(ifp, 1);
Make this driver compile for -stable also to prep for MFC
2002-04-26 23:11:23 +00:00
}
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
sc->wi_gone = 0;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
sc->sc_if_flags = ifp->if_flags;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = 0;
break;
case SIOCADDMULTI:
case SIOCDELMULTI:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_write_multi(sc);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
case SIOCGIFGENERIC:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_get_cfg(ifp, cmd, data);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
case SIOCSIFGENERIC:
error = suser(td);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (error == 0)
error = wi_set_cfg(ifp, cmd, data);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
case SIOCGPRISM2DEBUG:
error = copyin(ifr->ifr_data, &wreq, sizeof(wreq));
if (error)
break;
if (!(ifp->if_flags & IFF_RUNNING) ||
sc->sc_firmware_type == WI_LUCENT) {
error = EIO;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_get_debug(sc, &wreq);
if (error == 0)
error = copyout(&wreq, ifr->ifr_data, sizeof(wreq));
break;
case SIOCSPRISM2DEBUG:
if ((error = suser(td)))
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
return (error);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = copyin(ifr->ifr_data, &wreq, sizeof(wreq));
if (error)
break;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_set_debug(sc, &wreq);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
case SIOCG80211:
ireq = (struct ieee80211req *) data;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (ireq->i_type == IEEE80211_IOC_STATIONNAME) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ireq->i_len = sc->sc_nodelen + 1;
error = copyout(sc->sc_nodename, ireq->i_data,
ireq->i_len);
break;
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
goto ioctl_common;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case SIOCS80211:
ireq = (struct ieee80211req *) data;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (ireq->i_type == IEEE80211_IOC_STATIONNAME) {
error = suser(td);
if (error)
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (ireq->i_val != 0 ||
ireq->i_len > IEEE80211_NWID_LEN) {
error = EINVAL;
break;
}
memset(nodename, 0, IEEE80211_NWID_LEN);
error = copyin(ireq->i_data, nodename, ireq->i_len);
if (error)
break;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_enabled) {
error = wi_write_ssid(sc, WI_RID_NODENAME,
nodename, ireq->i_len);
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (error == 0) {
memcpy(sc->sc_nodename, nodename,
IEEE80211_NWID_LEN);
sc->sc_nodelen = ireq->i_len;
}
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
goto ioctl_common;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
default:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ioctl_common:
WI_LOCK(sc);
error = ieee80211_ioctl(ic, cmd, data);
if (error == ENETRESET) {
if (sc->sc_enabled)
wi_init(sc); /* XXX no error return */
error = 0;
}
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
}
return (error);
}
static int
wi_media_change(struct ifnet *ifp)
{
struct wi_softc *sc = ifp->if_softc;
update for new 802.11 support
2003-06-28 06:17:26 +00:00
int error;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
update for new 802.11 support
2003-06-28 06:17:26 +00:00
error = ieee80211_media_change(ifp);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (error == ENETRESET) {
if (sc->sc_enabled)
update for new 802.11 support
2003-06-28 06:17:26 +00:00
wi_init(sc); /* XXX no error return */
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = 0;
Add support for the Linksys WMP-11, Prism 2.5, PCI adaptor. Submitted by: Thomas Skibo <skibo@pacbell.net> MFC after: 2 weeks
2002-02-12 17:52:11 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return error;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
put function return types on a line by themselves as per style(9)
2001-12-27 20:12:03 +00:00
static void
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_media_status(struct ifnet *ifp, struct ifmediareq *imr)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = ifp->if_softc;
struct ieee80211com *ic = &sc->sc_ic;
u_int16_t val;
int rate, len;
if (sc->wi_gone || !sc->sc_enabled) {
imr->ifm_active = IFM_IEEE80211 | IFM_NONE;
imr->ifm_status = 0;
Four fixes from NetBSD: 1) Properly detect the Symbol based cards (The 3Com Airconnect and their ilk) and only reset them *ONCE* ever. This appears to make them work, but more testing is needed. The tests that would wedge up my machine completely now appear to work, but I have not real access points handy. 2) Report both the Station firmware and the Primary firmware on Prism based cards. On Lucent based cards, only report the station firmware since that's all it supports. On symbol cards, report the symbol specific firmware name as its station firmware. 3) Better Prism 2.5 and 3 family names. We really need to go table driven for this. 4) Workaround for bugs in Intersil's firmware is only needed for at most 0.8.2 and earlier, since 0.8.3 and later appear to work. Obtained from: NetBSD
2002-04-03 19:44:17 +00:00
return;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Four fixes from NetBSD: 1) Properly detect the Symbol based cards (The 3Com Airconnect and their ilk) and only reset them *ONCE* ever. This appears to make them work, but more testing is needed. The tests that would wedge up my machine completely now appear to work, but I have not real access points handy. 2) Report both the Station firmware and the Primary firmware on Prism based cards. On Lucent based cards, only report the station firmware since that's all it supports. On symbol cards, report the symbol specific firmware name as its station firmware. 3) Better Prism 2.5 and 3 family names. We really need to go table driven for this. 4) Workaround for bugs in Intersil's firmware is only needed for at most 0.8.2 and earlier, since 0.8.3 and later appear to work. Obtained from: NetBSD
2002-04-03 19:44:17 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
imr->ifm_status = IFM_AVALID;
imr->ifm_active = IFM_IEEE80211;
if (ic->ic_state == IEEE80211_S_RUN &&
(sc->sc_flags & WI_FLAGS_OUTRANGE) == 0)
imr->ifm_status |= IFM_ACTIVE;
len = sizeof(val);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (wi_read_rid(sc, WI_RID_CUR_TX_RATE, &val, &len) == 0 &&
len == sizeof(val)) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* convert to 802.11 rate */
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
val = le16toh(val);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
rate = val * 2;
if (sc->sc_firmware_type == WI_LUCENT) {
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (rate == 10)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
rate = 11; /* 5.5Mbps */
} else {
if (rate == 4*2)
rate = 11; /* 5.5Mbps */
else if (rate == 8*2)
rate = 22; /* 11Mbps */
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
} else
rate = 0;
update for new 802.11 support
2003-06-28 06:17:26 +00:00
imr->ifm_active |= ieee80211_rate2media(ic, rate, IEEE80211_MODE_11B);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (ic->ic_opmode) {
case IEEE80211_M_STA:
break;
case IEEE80211_M_IBSS:
imr->ifm_active |= IFM_IEEE80211_ADHOC;
break;
case IEEE80211_M_AHDEMO:
imr->ifm_active |= IFM_IEEE80211_ADHOC | IFM_FLAG0;
break;
case IEEE80211_M_HOSTAP:
imr->ifm_active |= IFM_IEEE80211_HOSTAP;
break;
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
case IEEE80211_M_MONITOR:
imr->ifm_active |= IFM_IEEE80211_MONITOR;
break;
Try to INIT the cards up to 5 times in a row rather than just once. It appears that some of the new PRISM2 cards need it. Fail the probe if we fail to read the MAC address. Fix a comment. Delete the unload printf. The bus system now prints this message.
2001-04-04 06:03:39 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
static void
wi_sync_bssid(struct wi_softc *sc, u_int8_t new_bssid[IEEE80211_ADDR_LEN])
{
struct ieee80211com *ic = &sc->sc_ic;
update for new 802.11 support
2003-06-28 06:17:26 +00:00
struct ieee80211_node *ni = ic->ic_bss;
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
better init
2002-04-11 03:31:45 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (IEEE80211_ADDR_EQ(new_bssid, ni->ni_bssid))
better init
2002-04-11 03:31:45 +00:00
return;
Add more diagnostic output for failure. s/1518/ETHER_MAX_LEN Some style changes, add some braces, mostly residual from having a lot of debug hooks added while working on this driver. Bring in a plethora of changes from NetBSD: revision 1.58 date: 2001/03/08 11:07:08; author: ichiro; state: Exp; lines: +17 -1 it wait until busy flag disappears. it was able to prevent some cards with late initializing faling in wi_reset(). revision 1.41 date: 2000/10/13 19:15:08; author: jonathan; state: Exp; lines: +4 -2 Fix wi_intr() to avoid touching card registers during insert/remove events, when sharing an interrupt with other devices: check sc->sc_enabled, and drop the interrupt if its' off. revision 1.30 date: 2000/08/18 04:11:48; author: jhawk; state: Exp; lines: +4 -4 Copy wi_{dst,src}_addr from struct wi_frame into faked-up ether_header instead of addr1 and addr2. THis means that tcpdump -e will show the correct MAC address for communications with access points instead of showing the BSSID. In the future there should be 802.11 support for bpf/libpcap/tcpdump, but that is aways down the road.
2001-04-10 05:29:26 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
DPRINTF(("wi_sync_bssid: bssid %s -> ", ether_sprintf(ni->ni_bssid)));
DPRINTF(("%s ?\n", ether_sprintf(new_bssid)));
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* In promiscuous mode, the BSSID field is not a reliable
* indicator of the firmware's BSSID. Damp spurious
* change-of-BSSID indications.
*/
if ((ifp->if_flags & IFF_PROMISC) != 0 &&
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
!ppsratecheck(&sc->sc_last_syn, &sc->sc_false_syns,
WI_MAX_FALSE_SYNS))
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return;
Apply some contributed patches to reduce number of tx buffer allocation failures and add some support for WEP on Prism II chip. Submitted by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
2000-12-15 23:34:13 +00:00
Eliminate some of the egregious bypass of the 802.11 state machine; instead use the intended entry points. There's still too much incestuous knowledge about the internals of the 802.11 layer but this at least fixes adhoc mode.
2005-01-01 17:45:11 +00:00
sc->sc_false_syns = MAX(0, sc->sc_false_syns - 1);
/*
* XXX hack; we should create a new node with the new bssid
* and replace the existing ic_bss with it but since we don't
* process management frames to collect state we cheat by
* reusing the existing node as we know wi_newstate will be
* called and it will overwrite the node state.
*/
ieee80211_sta_join(ic, ieee80211_ref_node(ni));
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
static void
wi_rx_monitor(struct wi_softc *sc, int fid)
{
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
struct wi_frame *rx_frame;
struct mbuf *m;
int datlen, hdrlen;
/* first allocate mbuf for packet storage */
m = m_getcl(M_DONTWAIT, MT_DATA, 0);
if (m == NULL) {
ifp->if_ierrors++;
return;
}
m->m_pkthdr.rcvif = ifp;
/* now read wi_frame first so we know how much data to read */
if (wi_read_bap(sc, fid, 0, mtod(m, caddr_t), sizeof(*rx_frame))) {
ifp->if_ierrors++;
goto done;
}
rx_frame = mtod(m, struct wi_frame *);
switch ((rx_frame->wi_status & WI_STAT_MAC_PORT) >> 8) {
case 7:
switch (rx_frame->wi_whdr.i_fc[0] & IEEE80211_FC0_TYPE_MASK) {
case IEEE80211_FC0_TYPE_DATA:
hdrlen = WI_DATA_HDRLEN;
datlen = rx_frame->wi_dat_len + WI_FCS_LEN;
break;
case IEEE80211_FC0_TYPE_MGT:
hdrlen = WI_MGMT_HDRLEN;
datlen = rx_frame->wi_dat_len + WI_FCS_LEN;
break;
case IEEE80211_FC0_TYPE_CTL:
/*
* prism2 cards don't pass control packets
* down properly or consistently, so we'll only
* pass down the header.
*/
hdrlen = WI_CTL_HDRLEN;
datlen = 0;
break;
default:
if_printf(ifp, "received packet of unknown type "
"on port 7\n");
ifp->if_ierrors++;
goto done;
}
break;
case 0:
hdrlen = WI_DATA_HDRLEN;
datlen = rx_frame->wi_dat_len + WI_FCS_LEN;
break;
default:
if_printf(ifp, "received packet on invalid "
"port (wi_status=0x%x)\n", rx_frame->wi_status);
ifp->if_ierrors++;
goto done;
}
if (hdrlen + datlen + 2 > MCLBYTES) {
if_printf(ifp, "oversized packet received "
"(wi_dat_len=%d, wi_status=0x%x)\n",
datlen, rx_frame->wi_status);
ifp->if_ierrors++;
goto done;
}
if (wi_read_bap(sc, fid, hdrlen, mtod(m, caddr_t) + hdrlen,
datlen + 2) == 0) {
m->m_pkthdr.len = m->m_len = hdrlen + datlen;
ifp->if_ipackets++;
BPF_MTAP(ifp, m); /* Handle BPF listeners. */
} else
ifp->if_ierrors++;
done:
m_freem(m);
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void
wi_rx_intr(struct wi_softc *sc)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct ieee80211com *ic = &sc->sc_ic;
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_frame frmhdr;
struct mbuf *m;
struct ieee80211_frame *wh;
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
struct ieee80211_node *ni;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int fid, len, off, rssi;
u_int8_t dir;
u_int16_t status;
u_int32_t rstamp;
fid = CSR_READ_2(sc, WI_RX_FID);
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
if (sc->wi_debug.wi_monitor) {
/*
* If we are in monitor mode just
* read the data from the device.
*/
wi_rx_monitor(sc, fid);
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_RX);
return;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* First read in the frame header */
if (wi_read_bap(sc, fid, 0, &frmhdr, sizeof(frmhdr))) {
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_RX);
ifp->if_ierrors++;
DPRINTF(("wi_rx_intr: read fid %x failed\n", fid));
return;
Apply some contributed patches to reduce number of tx buffer allocation failures and add some support for WEP on Prism II chip. Submitted by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
2000-12-15 23:34:13 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (IFF_DUMPPKTS(ifp))
wi_dump_pkt(&frmhdr, NULL, frmhdr.wi_rx_signal);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
/*
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
* Drop undecryptable or packets with receive errors here
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
status = le16toh(frmhdr.wi_status);
if (status & WI_STAT_ERRSTAT) {
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_RX);
ifp->if_ierrors++;
DPRINTF(("wi_rx_intr: fid %x error status %x\n", fid, status));
return;
Apply some contributed patches to reduce number of tx buffer allocation failures and add some support for WEP on Prism II chip. Submitted by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
2000-12-15 23:34:13 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
rssi = frmhdr.wi_rx_signal;
rstamp = (le16toh(frmhdr.wi_rx_tstamp0) << 16) |
le16toh(frmhdr.wi_rx_tstamp1);
Apply some contributed patches to reduce number of tx buffer allocation failures and add some support for WEP on Prism II chip. Submitted by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
2000-12-15 23:34:13 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
len = le16toh(frmhdr.wi_dat_len);
off = ALIGN(sizeof(struct ieee80211_frame));
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
o Add monitor mode support. This tested fine with prism cards but may require newer lucent/hermes firmware than indicated (investigating). I'm committing this now since it shouldn't hurt anything. o Vaguely related, add bogus frame length check from netbsd. Obtained from: netbsd
2003-07-21 23:20:40 +00:00
/*
* Sometimes the PRISM2.x returns bogusly large frames. Except
* in monitor mode, just throw them away.
*/
if (off + len > MCLBYTES) {
if (ic->ic_opmode != IEEE80211_M_MONITOR) {
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_RX);
ifp->if_ierrors++;
DPRINTF(("wi_rx_intr: oversized packet\n"));
return;
} else
len = 0;
}
Back out M_* changes, per decision of the TRB. Approved by: trb
2003-02-19 05:47:46 +00:00
MGETHDR(m, M_DONTWAIT, MT_DATA);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (m == NULL) {
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_RX);
ifp->if_ierrors++;
DPRINTF(("wi_rx_intr: MGET failed\n"));
return;
}
if (off + len > MHLEN) {
Back out M_* changes, per decision of the TRB. Approved by: trb
2003-02-19 05:47:46 +00:00
MCLGET(m, M_DONTWAIT);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if ((m->m_flags & M_EXT) == 0) {
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_RX);
m_freem(m);
ifp->if_ierrors++;
DPRINTF(("wi_rx_intr: MCLGET failed\n"));
return;
Fix tx-rate setting for Lucent cards. Submitted by: Eugene Perevyazko <john@pcs.dp.ua>
2002-04-14 23:18:40 +00:00
}
Apply some contributed patches to reduce number of tx buffer allocation failures and add some support for WEP on Prism II chip. Submitted by: YAMAMOTO Shigeru <shigeru@iij.ad.jp>
2000-12-15 23:34:13 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
m->m_data += off - sizeof(struct ieee80211_frame);
memcpy(m->m_data, &frmhdr.wi_whdr, sizeof(struct ieee80211_frame));
wi_read_bap(sc, fid, sizeof(frmhdr),
m->m_data + sizeof(struct ieee80211_frame), len);
m->m_pkthdr.len = m->m_len = sizeof(struct ieee80211_frame) + len;
m->m_pkthdr.rcvif = ifp;
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_RX);
Fix wep operation for station mode: o don't encapsulate on tx; the chip expect a raw frame w/o the crypto header o clear the WEP bit in the 802.11 header on rx so the 802.11 layer doesn't try to strip the crypto header o clobber the "drop unencoded frames" state bit when privacy is enabled so rx'd frames we pass up to the 802.11 layer are not discarded as unencrypted This stuff will need to be redone if anyone decides to add WPA support.
2004-12-17 03:57:16 +00:00
wh = mtod(m, struct ieee80211_frame *);
if (wh->i_fc[1] & IEEE80211_FC1_WEP) {
/*
* WEP is decrypted by hardware and the IV
* is stripped. Clear WEP bit so we don't
* try to process it in ieee80211_input.
* XXX fix for TKIP, et. al.
*/
wh->i_fc[1] &= ~IEEE80211_FC1_WEP;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#if NBPFILTER > 0
if (sc->sc_drvbpf) {
update radiotap support to reflect recent changes: o add xmit rate o drop rx time o add rx flags
2003-12-28 06:58:52 +00:00
/* XXX replace divide by table */
o eliminate widespread on-stack mbuf use for bpf by introducing a new bpf_mtap2 routine that does the right thing for an mbuf and a variable-length chunk of data that should be prepended. o while we're sweeping the drivers, use u_int32_t uniformly when when prepending the address family (several places were assuming sizeof(int) was 4) o return M_ASSERTVALID to BPF_MTAP* now that all stack-allocated mbufs have been eliminated; this may better be moved to the bpf routines Reviewed by: arch@ and several others
2003-12-28 03:56:00 +00:00
sc->sc_rx_th.wr_rate = frmhdr.wi_rx_rate / 5;
Eliminate bogus usage of WI_RSSI_TO_DBM(). Not only does it bogusly clip/destroy the dB value contained in the wi(4)'s receive frames, it doesn't match with the flag set in the radiotap header (unperturbed dB versus dBm).
2004-03-17 21:54:52 +00:00
sc->sc_rx_th.wr_antsignal = frmhdr.wi_rx_signal;
sc->sc_rx_th.wr_antnoise = frmhdr.wi_rx_silence;
update radiotap support to reflect recent changes: o add xmit rate o drop rx time o add rx flags
2003-12-28 06:58:52 +00:00
sc->sc_rx_th.wr_flags = 0;
if (frmhdr.wi_status & WI_STAT_PCF)
sc->sc_rx_th.wr_flags |= IEEE80211_RADIOTAP_F_CFP;
Fix wep operation for station mode: o don't encapsulate on tx; the chip expect a raw frame w/o the crypto header o clear the WEP bit in the 802.11 header on rx so the 802.11 layer doesn't try to strip the crypto header o clobber the "drop unencoded frames" state bit when privacy is enabled so rx'd frames we pass up to the 802.11 layer are not discarded as unencrypted This stuff will need to be redone if anyone decides to add WPA support.
2004-12-17 03:57:16 +00:00
/* XXX IEEE80211_RADIOTAP_F_WEP */
o eliminate widespread on-stack mbuf use for bpf by introducing a new bpf_mtap2 routine that does the right thing for an mbuf and a variable-length chunk of data that should be prepended. o while we're sweeping the drivers, use u_int32_t uniformly when when prepending the address family (several places were assuming sizeof(int) was 4) o return M_ASSERTVALID to BPF_MTAP* now that all stack-allocated mbufs have been eliminated; this may better be moved to the bpf routines Reviewed by: arch@ and several others
2003-12-28 03:56:00 +00:00
bpf_mtap2(sc->sc_drvbpf,
radiotap updates: o force little-endian byte order for header o pad header to 32-bit boundary to guard against applications that assume packet data alignment
2004-04-01 00:38:45 +00:00
&sc->sc_rx_th, sc->sc_rx_th_len, m);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#endif
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* synchronize driver's BSSID with firmware's BSSID */
dir = wh->i_fc[1] & IEEE80211_FC1_DIR_MASK;
if (ic->ic_opmode == IEEE80211_M_IBSS && dir == IEEE80211_FC1_DIR_NODS)
wi_sync_bssid(sc, wh->i_addr3);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
/*
* Locate the node for sender, track state, and
* then pass this node (referenced) up to the 802.11
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
* layer for its use.
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
*/
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ni = ieee80211_find_rxnode(ic, (struct ieee80211_frame_min *) wh);
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
/*
* Send frame up for processing.
*/
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ieee80211_input(ic, m, ni, rssi, rstamp);
MFp4 changes to fix locking issues and correct reference count handling of station entries in hostap mode: Input path: o driver is now expected to find the node associated with the sender of a received frame; use ic_bss if none is located o driver passes the (referenced) node into ieee80211_input for use within the wlan module and is responsible for cleaning up on return o the antenna state is no longer passed up with each frame; this is now considered driver-private state and drivers are responsible for keeping it in the driver-private part of a node Output path: Revamp output path for management frames to eliminate redundant locking that causes problems and to correct reference counting bogosity that occurs when stations are timed out due to inactivity (in AP mode). On output the refcnt'd node is stashed in the pkthdr's recvif field (yech) and retrieved by the driver. This eliminates an unref/ref scenario and related node table unlock/lock due to the driver looking up the node. This is particularly important when stations are timed out as this causes a lock order reversal that can result in a deadlock. As a byproduct we also reduce the overhead for sending management frames (minimal). Additional fallout from this is a change to ieee80211_encap to return a refcn't node for tieing to the outbound frame. Node refcnts are not reclaimed until after a frame is completely processed (e.g. in the tx interrupt handler). This is especially important for timed out stations as this deref will be the final one causing the node entry to be reclaimed. Additional semi-related changes: o replace m_copym use with m_copypacket (optimization) o add assert to verify ic_bss is never free'd during normal operation o add comments explaining calling conventions by drivers for frames going in each direction o remove extraneous code that "cannot be executed" (e.g. because pointers may never be null)
2003-08-19 22:17:04 +00:00
/*
* The frame may have caused the node to be marked for
* reclamation (e.g. in response to a DEAUTH message)
* so use free_node here instead of unref_node.
*/
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
ieee80211_free_node(ni);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void
wi_tx_ex_intr(struct wi_softc *sc)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_frame frmhdr;
int fid;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
fid = CSR_READ_2(sc, WI_TX_CMP_FID);
/* Read in the frame header */
if (wi_read_bap(sc, fid, 0, &frmhdr, sizeof(frmhdr)) == 0) {
u_int16_t status = le16toh(frmhdr.wi_status);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/*
* Spontaneous station disconnects appear as xmit
* errors. Don't announce them and/or count them
* as an output error.
*/
if ((status & WI_TXSTAT_DISCONNECT) == 0) {
if (ppsratecheck(&lasttxerror, &curtxeps, wi_txerate)) {
if_printf(ifp, "tx failed");
if (status & WI_TXSTAT_RET_ERR)
printf(", retry limit exceeded");
if (status & WI_TXSTAT_AGED_ERR)
printf(", max transmit lifetime exceeded");
if (status & WI_TXSTAT_DISCONNECT)
printf(", port disconnected");
if (status & WI_TXSTAT_FORM_ERR)
printf(", invalid format (data len %u src %6D)",
le16toh(frmhdr.wi_dat_len),
frmhdr.wi_ehdr.ether_shost, ":");
if (status & ~0xf)
printf(", status=0x%x", status);
printf("\n");
}
ifp->if_oerrors++;
} else {
DPRINTF(("port disconnected\n"));
ifp->if_collisions++; /* XXX */
}
} else
DPRINTF(("wi_tx_ex_intr: read fid %x failed\n", fid));
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_TX_EXC);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void
wi_tx_intr(struct wi_softc *sc)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int fid, cur;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
if (sc->wi_gone)
return;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
fid = CSR_READ_2(sc, WI_ALLOC_FID);
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_ALLOC);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
cur = sc->sc_txcur;
if (sc->sc_txd[cur].d_fid != fid) {
if_printf(ifp, "bad alloc %x != %x, cur %d nxt %d\n",
fid, sc->sc_txd[cur].d_fid, cur, sc->sc_txnext);
return;
}
sc->sc_tx_timer = 0;
sc->sc_txd[cur].d_len = 0;
o Lucent cards don't seem to like multiple buffers for tx. Use only one tx buffer for these cards. The old driver only used one. We use 1 for symbol, and 3 for prism cards. o Don't do the maximum loops thing in the ISR. In fact, revert to the old interrupt handler. Lucent cards don't seem to work too well if you don't disable/enable interrupts from the card in the ISR. Between these two changes, Lucent cards suck less. They work in autoselect mode only. And seem to get 1Mbps or 2Mbps only. Setting a specific media speed doesn't work, and I've had a few issues even with these patches. They turn a former brick into a nearly useful card. These patches work on the prism 2 and 2.5 PC Card cards that I have. I've not tested this on PCI cards. I suspect, but couldn't find proof, that they were the reason that the ISR was changed so radically from its FreeBSD roots in NetBSD. We might need to have a variant ISR if so.
2003-03-18 04:22:42 +00:00
sc->sc_txcur = cur = (cur + 1) % sc->sc_ntxbuf;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_txd[cur].d_len == 0)
ifp->if_flags &= ~IFF_OACTIVE;
else {
if (wi_cmd(sc, WI_CMD_TX | WI_RECLAIM, sc->sc_txd[cur].d_fid,
0, 0)) {
if_printf(ifp, "xmit failed\n");
sc->sc_txd[cur].d_len = 0;
} else {
sc->sc_tx_timer = 5;
ifp->if_timer = 1;
}
limit the amount of retries when sending data to prevent lockups.
2001-03-27 05:03:49 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void
wi_info_intr(struct wi_softc *sc)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct ieee80211com *ic = &sc->sc_ic;
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int i, fid, len, off;
u_int16_t ltbuf[2];
u_int16_t stat;
u_int32_t *ptr;
fid = CSR_READ_2(sc, WI_INFO_FID);
wi_read_bap(sc, fid, 0, ltbuf, sizeof(ltbuf));
switch (le16toh(ltbuf[1])) {
case WI_INFO_LINK_STAT:
wi_read_bap(sc, fid, sizeof(ltbuf), &stat, sizeof(stat));
DPRINTF(("wi_info_intr: LINK_STAT 0x%x\n", le16toh(stat)));
switch (le16toh(stat)) {
case WI_INFO_LINK_STAT_CONNECTED:
sc->sc_flags &= ~WI_FLAGS_OUTRANGE;
if (ic->ic_state == IEEE80211_S_RUN &&
ic->ic_opmode != IEEE80211_M_IBSS)
break;
/* FALLTHROUGH */
case WI_INFO_LINK_STAT_AP_CHG:
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
ieee80211_new_state(ic, IEEE80211_S_RUN, -1);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_INFO_LINK_STAT_AP_INR:
sc->sc_flags &= ~WI_FLAGS_OUTRANGE;
break;
case WI_INFO_LINK_STAT_AP_OOR:
if (sc->sc_firmware_type == WI_SYMBOL &&
sc->sc_scan_timer > 0) {
if (wi_cmd(sc, WI_CMD_INQUIRE,
WI_INFO_HOST_SCAN_RESULTS, 0, 0) != 0)
sc->sc_scan_timer = 0;
break;
}
if (ic->ic_opmode == IEEE80211_M_STA)
sc->sc_flags |= WI_FLAGS_OUTRANGE;
break;
case WI_INFO_LINK_STAT_DISCONNECTED:
case WI_INFO_LINK_STAT_ASSOC_FAILED:
if (ic->ic_opmode == IEEE80211_M_STA)
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
ieee80211_new_state(ic, IEEE80211_S_INIT, -1);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
}
break;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_INFO_COUNTERS:
/* some card versions have a larger stats structure */
len = min(le16toh(ltbuf[0]) - 1, sizeof(sc->sc_stats) / 4);
ptr = (u_int32_t *)&sc->sc_stats;
off = sizeof(ltbuf);
for (i = 0; i < len; i++, off += 2, ptr++) {
wi_read_bap(sc, fid, off, &stat, sizeof(stat));
#ifdef WI_HERMES_STATS_WAR
if (stat & 0xf000)
stat = ~stat;
#endif
*ptr += stat;
}
ifp->if_collisions = sc->sc_stats.wi_tx_single_retries +
sc->sc_stats.wi_tx_multi_retries +
sc->sc_stats.wi_tx_retry_limit;
break;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_INFO_SCAN_RESULTS:
case WI_INFO_HOST_SCAN_RESULTS:
wi_scan_result(sc, fid, le16toh(ltbuf[0]));
break;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
default:
DPRINTF(("wi_info_intr: got fid %x type %x len %d\n", fid,
le16toh(ltbuf[1]), le16toh(ltbuf[0])));
break;
Add more diagnostic output for failure. s/1518/ETHER_MAX_LEN Some style changes, add some braces, mostly residual from having a lot of debug hooks added while working on this driver. Bring in a plethora of changes from NetBSD: revision 1.58 date: 2001/03/08 11:07:08; author: ichiro; state: Exp; lines: +17 -1 it wait until busy flag disappears. it was able to prevent some cards with late initializing faling in wi_reset(). revision 1.41 date: 2000/10/13 19:15:08; author: jonathan; state: Exp; lines: +4 -2 Fix wi_intr() to avoid touching card registers during insert/remove events, when sharing an interrupt with other devices: check sc->sc_enabled, and drop the interrupt if its' off. revision 1.30 date: 2000/08/18 04:11:48; author: jhawk; state: Exp; lines: +4 -4 Copy wi_{dst,src}_addr from struct wi_frame into faked-up ether_header instead of addr1 and addr2. THis means that tcpdump -e will show the correct MAC address for communications with access points instead of showing the BSSID. In the future there should be 802.11 support for bpf/libpcap/tcpdump, but that is aways down the road.
2001-04-10 05:29:26 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_INFO);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_write_multi(struct wi_softc *sc)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
struct ifnet *ifp = sc->sc_ifp;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int n;
struct ifmultiaddr *ifma;
struct wi_mcast mlist;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) {
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
allmulti:
memset(&mlist, 0, sizeof(mlist));
return wi_write_rid(sc, WI_RID_MCAST_LIST, &mlist,
sizeof(mlist));
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
n = 0;
Modify device drivers supporting multicast addresses to lock if_addr_mtx over iteration of their multicast address lists when synchronizing the hardware address filter with the network stack-maintained list. Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca> MFC after: 1 week
2005-08-03 00:18:35 +00:00
IF_ADDR_LOCK(ifp);
Make this driver compile for -stable also to prep for MFC
2002-04-26 23:11:23 +00:00
#if __FreeBSD_version < 500000
LIST_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
#else
Convert if_multiaddrs from LIST to TAILQ so that it can be traversed backwards in the three drivers which want to do that. Reviewed by: mikeh
2001-02-06 10:12:15 +00:00
TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
Make this driver compile for -stable also to prep for MFC
2002-04-26 23:11:23 +00:00
#endif
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
if (ifma->ifma_addr->sa_family != AF_LINK)
continue;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (n >= 16)
goto allmulti;
IEEE80211_ADDR_COPY(&mlist.wi_mcast[n],
(LLADDR((struct sockaddr_dl *)ifma->ifma_addr)));
n++;
}
Modify device drivers supporting multicast addresses to lock if_addr_mtx over iteration of their multicast address lists when synchronizing the hardware address filter with the network stack-maintained list. Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca> MFC after: 1 week
2005-08-03 00:18:35 +00:00
IF_ADDR_UNLOCK(ifp);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return wi_write_rid(sc, WI_RID_MCAST_LIST, &mlist,
IEEE80211_ADDR_LEN * n);
}
static void
wi_read_nicid(struct wi_softc *sc)
{
struct wi_card_ident *id;
char *p;
int len;
u_int16_t ver[4];
/* getting chip identity */
memset(ver, 0, sizeof(ver));
len = sizeof(ver);
wi_read_rid(sc, WI_RID_CARD_ID, ver, &len);
device_printf(sc->sc_dev, "using ");
sc->sc_firmware_type = WI_NOTYPE;
for (id = wi_card_ident; id->card_name != NULL; id++) {
if (le16toh(ver[0]) == id->card_id) {
printf("%s", id->card_name);
sc->sc_firmware_type = id->firm_type;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
}
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_firmware_type == WI_NOTYPE) {
if (le16toh(ver[0]) & 0x8000) {
printf("Unknown PRISM2 chip");
sc->sc_firmware_type = WI_INTERSIL;
} else {
printf("Unknown Lucent chip");
sc->sc_firmware_type = WI_LUCENT;
}
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* get primary firmware version (Only Prism chips) */
if (sc->sc_firmware_type != WI_LUCENT) {
memset(ver, 0, sizeof(ver));
len = sizeof(ver);
wi_read_rid(sc, WI_RID_PRI_IDENTITY, ver, &len);
sc->sc_pri_firmware_ver = le16toh(ver[2]) * 10000 +
le16toh(ver[3]) * 100 + le16toh(ver[1]);
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* get station firmware version */
memset(ver, 0, sizeof(ver));
len = sizeof(ver);
wi_read_rid(sc, WI_RID_STA_IDENTITY, ver, &len);
sc->sc_sta_firmware_ver = le16toh(ver[2]) * 10000 +
le16toh(ver[3]) * 100 + le16toh(ver[1]);
if (sc->sc_firmware_type == WI_INTERSIL &&
(sc->sc_sta_firmware_ver == 10102 ||
sc->sc_sta_firmware_ver == 20102)) {
char ident[12];
memset(ident, 0, sizeof(ident));
len = sizeof(ident);
/* value should be the format like "V2.00-11" */
if (wi_read_rid(sc, WI_RID_SYMBOL_IDENTITY, ident, &len) == 0 &&
*(p = (char *)ident) >= 'A' &&
p[2] == '.' && p[5] == '-' && p[8] == '\0') {
sc->sc_firmware_type = WI_SYMBOL;
sc->sc_sta_firmware_ver = (p[1] - '0') * 10000 +
(p[3] - '0') * 1000 + (p[4] - '0') * 100 +
(p[6] - '0') * 10 + (p[7] - '0');
}
}
printf("\n");
device_printf(sc->sc_dev, "%s Firmware: ",
sc->sc_firmware_type == WI_LUCENT ? "Lucent" :
(sc->sc_firmware_type == WI_SYMBOL ? "Symbol" : "Intersil"));
if (sc->sc_firmware_type != WI_LUCENT) /* XXX */
printf("Primary (%u.%u.%u), ",
sc->sc_pri_firmware_ver / 10000,
(sc->sc_pri_firmware_ver % 10000) / 100,
sc->sc_pri_firmware_ver % 100);
printf("Station (%u.%u.%u)\n",
sc->sc_sta_firmware_ver / 10000,
(sc->sc_sta_firmware_ver % 10000) / 100,
sc->sc_sta_firmware_ver % 100);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_write_ssid(struct wi_softc *sc, int rid, u_int8_t *buf, int buflen)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_ssid ssid;
if (buflen > IEEE80211_NWID_LEN)
return ENOBUFS;
memset(&ssid, 0, sizeof(ssid));
ssid.wi_len = htole16(buflen);
memcpy(ssid.wi_ssid, buf, buflen);
return wi_write_rid(sc, rid, &ssid, sizeof(ssid));
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_get_cfg(struct ifnet *ifp, u_long cmd, caddr_t data)
{
struct wi_softc *sc = ifp->if_softc;
struct ieee80211com *ic = &sc->sc_ic;
struct ifreq *ifr = (struct ifreq *)data;
struct wi_req wreq;
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
struct wi_scan_res *res;
Fix wi(4)'s WI_RID_SCAN_RES ioctl (wicontrol -L). The wrong length is computed, so the user thinks that for non-PRISM cards there are more APs represented than exist.
2003-11-04 00:31:58 +00:00
size_t reslen;
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
int len, n, error, mif, val, off, i;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = copyin(ifr->ifr_data, &wreq, sizeof(wreq));
if (error)
return error;
len = (wreq.wi_len - 1) * 2;
if (len < sizeof(u_int16_t))
return ENOSPC;
if (len > sizeof(wreq.wi_val))
len = sizeof(wreq.wi_val);
switch (wreq.wi_type) {
case WI_RID_IFACE_STATS:
memcpy(wreq.wi_val, &sc->sc_stats, sizeof(sc->sc_stats));
if (len < sizeof(sc->sc_stats))
error = ENOSPC;
else
len = sizeof(sc->sc_stats);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_ENCRYPTION:
case WI_RID_TX_CRYPT_KEY:
case WI_RID_DEFLT_CRYPT_KEYS:
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
case WI_RID_TX_RATE:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
return ieee80211_cfgget(ic, cmd, data);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_MICROWAVE_OVEN:
if (sc->sc_enabled && (sc->sc_flags & WI_FLAGS_HAS_MOR)) {
error = wi_read_rid(sc, wreq.wi_type, wreq.wi_val,
&len);
break;
}
wreq.wi_val[0] = htole16(sc->sc_microwave_oven);
len = sizeof(u_int16_t);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_DBM_ADJUST:
if (sc->sc_enabled && (sc->sc_flags & WI_FLAGS_HAS_DBMADJUST)) {
error = wi_read_rid(sc, wreq.wi_type, wreq.wi_val,
&len);
break;
}
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
wreq.wi_val[0] = htole16(sc->sc_dbm_offset);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
len = sizeof(u_int16_t);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_ROAMING_MODE:
if (sc->sc_enabled && (sc->sc_flags & WI_FLAGS_HAS_ROAMING)) {
error = wi_read_rid(sc, wreq.wi_type, wreq.wi_val,
&len);
break;
}
wreq.wi_val[0] = htole16(sc->sc_roaming_mode);
len = sizeof(u_int16_t);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
case WI_RID_SYSTEM_SCALE:
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_enabled && (sc->sc_flags & WI_FLAGS_HAS_SYSSCALE)) {
error = wi_read_rid(sc, wreq.wi_type, wreq.wi_val,
&len);
break;
}
wreq.wi_val[0] = htole16(sc->sc_system_scale);
len = sizeof(u_int16_t);
Add roaming and microwave oven support. Some minor formatting nits. Some buggy firmware workarounds. Fix some endian bugs. These reduce the diffs from NetBSD, but NetBSD does have more changes since my last manual merge.
2002-03-05 16:18:14 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_FRAG_THRESH:
if (sc->sc_enabled && (sc->sc_flags & WI_FLAGS_HAS_FRAGTHR)) {
error = wi_read_rid(sc, wreq.wi_type, wreq.wi_val,
&len);
break;
}
update for new 802.11 support
2003-06-28 06:17:26 +00:00
wreq.wi_val[0] = htole16(ic->ic_fragthreshold);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
len = sizeof(u_int16_t);
Add roaming and microwave oven support. Some minor formatting nits. Some buggy firmware workarounds. Fix some endian bugs. These reduce the diffs from NetBSD, but NetBSD does have more changes since my last manual merge.
2002-03-05 16:18:14 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_READ_APS:
if (ic->ic_opmode == IEEE80211_M_HOSTAP)
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
return ieee80211_cfgget(ic, cmd, data);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_scan_timer > 0) {
error = EINPROGRESS;
break;
}
n = sc->sc_naps;
if (len < sizeof(n)) {
error = ENOSPC;
break;
}
if (len < sizeof(n) + sizeof(struct wi_apinfo) * n)
n = (len - sizeof(n)) / sizeof(struct wi_apinfo);
len = sizeof(n) + sizeof(struct wi_apinfo) * n;
memcpy(wreq.wi_val, &n, sizeof(n));
memcpy((caddr_t)wreq.wi_val + sizeof(n), sc->sc_aps,
sizeof(struct wi_apinfo) * n);
Add support to wicontrol(8) and wi(4) for enabling and configuring power management. This will only work on newer firmware revisions; older firmware will silently ignore the attempts to turn power management on. Patches supplied by: Brad Karp <karp@eecs.harvard.edu>
1999-05-07 03:28:54 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_PRISM2:
wreq.wi_val[0] = sc->sc_firmware_type != WI_LUCENT;
len = sizeof(u_int16_t);
Add support for WEP (encryption) for silver and gold WaveLAN/IEEE turbo cards. Also update wicontrol to enable/disable encryption, set WEP keys and set the TX key index. Silver cards only have 40-bit keys. This is something of a quick hack, but it works well enough for me to commit this from the LinuxWorld exhibit floor. The WEP support only shows up if you have a card that supports it. Would have been approved by: jkh, if he hadn't wandered off somewhere Approved in his place by: msmith, who's standing right here
2000-02-02 17:59:13 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_MIF:
mif = wreq.wi_val[0];
error = wi_cmd(sc, WI_CMD_READMIF, mif, 0, 0);
val = CSR_READ_2(sc, WI_RESP0);
wreq.wi_val[0] = val;
len = sizeof(u_int16_t);
Add support for WEP (encryption) for silver and gold WaveLAN/IEEE turbo cards. Also update wicontrol to enable/disable encryption, set WEP keys and set the TX key index. Silver cards only have 40-bit keys. This is something of a quick hack, but it works well enough for me to commit this from the LinuxWorld exhibit floor. The WEP support only shows up if you have a card that supports it. Would have been approved by: jkh, if he hadn't wandered off somewhere Approved in his place by: msmith, who's standing right here
2000-02-02 17:59:13 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_ZERO_CACHE:
case WI_RID_PROCFRAME: /* ignore for compatibility */
/* XXX ??? */
Add support for WEP (encryption) for silver and gold WaveLAN/IEEE turbo cards. Also update wicontrol to enable/disable encryption, set WEP keys and set the TX key index. Silver cards only have 40-bit keys. This is something of a quick hack, but it works well enough for me to commit this from the LinuxWorld exhibit floor. The WEP support only shows up if you have a card that supports it. Would have been approved by: jkh, if he hadn't wandered off somewhere Approved in his place by: msmith, who's standing right here
2000-02-02 17:59:13 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_READ_CACHE:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
return ieee80211_cfgget(ic, cmd, data);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
case WI_RID_SCAN_RES: /* compatibility interface */
if (ic->ic_opmode == IEEE80211_M_HOSTAP)
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
return ieee80211_cfgget(ic, cmd, data);
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
if (sc->sc_scan_timer > 0) {
error = EINPROGRESS;
break;
}
n = sc->sc_naps;
Fix wi(4)'s WI_RID_SCAN_RES ioctl (wicontrol -L). The wrong length is computed, so the user thinks that for non-PRISM cards there are more APs represented than exist.
2003-11-04 00:31:58 +00:00
if (sc->sc_firmware_type == WI_LUCENT) {
off = 0;
reslen = WI_WAVELAN_RES_SIZE;
} else {
off = sizeof(struct wi_scan_p2_hdr);
reslen = WI_PRISM2_RES_SIZE;
}
if (len < off + reslen * n)
n = (len - off) / reslen;
len = off + reslen * n;
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
if (off != 0) {
struct wi_scan_p2_hdr *p2 = (struct wi_scan_p2_hdr *)wreq.wi_val;
/*
* Prepend Prism-specific header.
*/
if (len < sizeof(struct wi_scan_p2_hdr)) {
error = ENOSPC;
break;
}
p2 = (struct wi_scan_p2_hdr *)wreq.wi_val;
p2->wi_rsvd = 0;
p2->wi_reason = n; /* XXX */
}
Fix wi(4)'s WI_RID_SCAN_RES ioctl (wicontrol -L). The wrong length is computed, so the user thinks that for non-PRISM cards there are more APs represented than exist.
2003-11-04 00:31:58 +00:00
for (i = 0; i < n; i++, off += reslen) {
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
const struct wi_apinfo *ap = &sc->sc_aps[i];
res = (struct wi_scan_res *)((char *)wreq.wi_val + off);
res->wi_chan = ap->channel;
res->wi_noise = ap->noise;
res->wi_signal = ap->signal;
IEEE80211_ADDR_COPY(res->wi_bssid, ap->bssid);
res->wi_interval = ap->interval;
res->wi_capinfo = ap->capinfo;
res->wi_ssid_len = ap->namelen;
memcpy(res->wi_ssid, ap->name,
IEEE80211_NWID_LEN);
if (sc->sc_firmware_type != WI_LUCENT) {
/* XXX not saved from Prism cards */
memset(res->wi_srates, 0,
sizeof(res->wi_srates));
res->wi_rate = ap->rate;
res->wi_rsvd = 0;
Fix wi(4)'s WI_RID_SCAN_RES ioctl (wicontrol -L). The wrong length is computed, so the user thinks that for non-PRISM cards there are more APs represented than exist.
2003-11-04 00:31:58 +00:00
}
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
}
break;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
default:
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_enabled) {
error = wi_read_rid(sc, wreq.wi_type, wreq.wi_val,
&len);
break;
}
switch (wreq.wi_type) {
case WI_RID_MAX_DATALEN:
wreq.wi_val[0] = htole16(sc->sc_max_datalen);
len = sizeof(u_int16_t);
break;
case WI_RID_RTS_THRESH:
update for new 802.11 support
2003-06-28 06:17:26 +00:00
wreq.wi_val[0] = htole16(ic->ic_rtsthreshold);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
len = sizeof(u_int16_t);
break;
case WI_RID_CNFAUTHMODE:
wreq.wi_val[0] = htole16(sc->sc_cnfauthmode);
len = sizeof(u_int16_t);
break;
case WI_RID_NODENAME:
if (len < sc->sc_nodelen + sizeof(u_int16_t)) {
error = ENOSPC;
break;
}
len = sc->sc_nodelen + sizeof(u_int16_t);
wreq.wi_val[0] = htole16((sc->sc_nodelen + 1) / 2);
memcpy(&wreq.wi_val[1], sc->sc_nodename,
sc->sc_nodelen);
break;
default:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
return ieee80211_cfgget(ic, cmd, data);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (error)
return error;
wreq.wi_len = (len + 1) / 2 + 1;
return copyout(&wreq, ifr->ifr_data, (wreq.wi_len + 1) * 2);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
put function return types on a line by themselves as per style(9)
2001-12-27 20:12:03 +00:00
static int
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_set_cfg(struct ifnet *ifp, u_long cmd, caddr_t data)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = ifp->if_softc;
struct ieee80211com *ic = &sc->sc_ic;
struct ifreq *ifr = (struct ifreq *)data;
struct wi_req wreq;
struct mbuf *m;
int i, len, error, mif, val;
update for new 802.11 support
2003-06-28 06:17:26 +00:00
struct ieee80211_rateset *rs;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK_DECL();
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = copyin(ifr->ifr_data, &wreq, sizeof(wreq));
if (error)
return error;
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
len = wreq.wi_len ? (wreq.wi_len - 1) * 2 : 0;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (wreq.wi_type) {
case WI_RID_DBM_ADJUST:
return ENODEV;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_NODENAME:
if (le16toh(wreq.wi_val[0]) * 2 > len ||
le16toh(wreq.wi_val[0]) > sizeof(sc->sc_nodename)) {
error = ENOSPC;
break;
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
if (sc->sc_enabled)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_write_rid(sc, wreq.wi_type, wreq.wi_val,
len);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (error == 0) {
sc->sc_nodelen = le16toh(wreq.wi_val[0]) * 2;
memcpy(sc->sc_nodename, &wreq.wi_val[1],
sc->sc_nodelen);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_MICROWAVE_OVEN:
case WI_RID_ROAMING_MODE:
case WI_RID_SYSTEM_SCALE:
case WI_RID_FRAG_THRESH:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
/* XXX unlocked reads */
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (wreq.wi_type == WI_RID_MICROWAVE_OVEN &&
(sc->sc_flags & WI_FLAGS_HAS_MOR) == 0)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (wreq.wi_type == WI_RID_ROAMING_MODE &&
(sc->sc_flags & WI_FLAGS_HAS_ROAMING) == 0)
MFNetBSD: 1.60: Add range checking, but put it higher up in the food chain than NetBSD (this should be fixed there as well). Obtained From: NetBSD
2002-04-04 22:22:31 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (wreq.wi_type == WI_RID_SYSTEM_SCALE &&
(sc->sc_flags & WI_FLAGS_HAS_SYSSCALE) == 0)
Close PR #20963. Do not pass encryption keys back to the caller via wi_ioctl() unless they're the superuser.
2000-09-07 17:05:12 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (wreq.wi_type == WI_RID_FRAG_THRESH &&
(sc->sc_flags & WI_FLAGS_HAS_FRAGTHR) == 0)
break;
/* FALLTHROUGH */
case WI_RID_RTS_THRESH:
case WI_RID_CNFAUTHMODE:
case WI_RID_MAX_DATALEN:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_enabled) {
error = wi_write_rid(sc, wreq.wi_type, wreq.wi_val,
sizeof(u_int16_t));
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (error != 0) {
WI_UNLOCK(sc);
Require privilege to flush the signal cache on if_an and if_wi 802.11 cards. Reviewed by: imp (if_wi)
2002-12-24 14:46:01 +00:00
break;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (wreq.wi_type) {
case WI_RID_FRAG_THRESH:
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_fragthreshold = le16toh(wreq.wi_val[0]);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_RTS_THRESH:
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ic->ic_rtsthreshold = le16toh(wreq.wi_val[0]);
MFNetBSD: 1.60: Add range checking, but put it higher up in the food chain than NetBSD (this should be fixed there as well). Obtained From: NetBSD
2002-04-04 22:22:31 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_MICROWAVE_OVEN:
sc->sc_microwave_oven = le16toh(wreq.wi_val[0]);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_ROAMING_MODE:
sc->sc_roaming_mode = le16toh(wreq.wi_val[0]);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_SYSTEM_SCALE:
sc->sc_system_scale = le16toh(wreq.wi_val[0]);
break;
case WI_RID_CNFAUTHMODE:
sc->sc_cnfauthmode = le16toh(wreq.wi_val[0]);
break;
case WI_RID_MAX_DATALEN:
sc->sc_max_datalen = le16toh(wreq.wi_val[0]);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
break;
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_TX_RATE:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (le16toh(wreq.wi_val[0])) {
case 3:
diff reduction against p4: define IEEE80211_FIXED_RATE_NONE and use it instead of -1
2005-07-22 16:50:18 +00:00
ic->ic_fixed_rate = IEEE80211_FIXED_RATE_NONE;
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
default:
update for new 802.11 support
2003-06-28 06:17:26 +00:00
rs = &ic->ic_sup_rates[IEEE80211_MODE_11B];
for (i = 0; i < rs->rs_nrates; i++) {
if ((rs->rs_rates[i] & IEEE80211_RATE_VAL)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/ 2 == le16toh(wreq.wi_val[0]))
Currently, each wireless networking driver has it's own control program despite the fact that most people want to set exactly the same settings regardless of which card they have. It has been repeatidly suggested that this configuration should be done via ifconfig. This patch implements the required functionality in ifconfig and add support to the wi and an drivers. It also provides partial, untested support for the awi driver. PR: 25577 Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
2001-05-26 09:27:08 +00:00
break;
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (i == rs->rs_nrates) {
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return EINVAL;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ic->ic_fixed_rate = i;
}
if (sc->sc_enabled)
error = wi_write_txrate(sc);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
Currently, each wireless networking driver has it's own control program despite the fact that most people want to set exactly the same settings regardless of which card they have. It has been repeatidly suggested that this configuration should be done via ifconfig. This patch implements the required functionality in ifconfig and add support to the wi and an drivers. It also provides partial, untested support for the awi driver. PR: 25577 Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
2001-05-26 09:27:08 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_SCAN_APS:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_enabled && ic->ic_opmode != IEEE80211_M_HOSTAP)
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
error = wi_scan_ap(sc, 0x3fff, 0x000f);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
break;
case WI_RID_SCAN_REQ: /* compatibility interface */
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
if (sc->sc_enabled && ic->ic_opmode != IEEE80211_M_HOSTAP)
error = wi_scan_ap(sc, wreq.wi_val[0], wreq.wi_val[1]);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
Currently, each wireless networking driver has it's own control program despite the fact that most people want to set exactly the same settings regardless of which card they have. It has been repeatidly suggested that this configuration should be done via ifconfig. This patch implements the required functionality in ifconfig and add support to the wi and an drivers. It also provides partial, untested support for the awi driver. PR: 25577 Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
2001-05-26 09:27:08 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_MGMT_XMIT:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
if (!sc->sc_enabled)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = ENETDOWN;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
else if (ic->ic_mgtq.ifq_len > 5)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = EAGAIN;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
else {
/* NB: m_devget uses M_DONTWAIT so can hold the lock */
/* XXX wi_len looks in u_int8_t, not in u_int16_t */
m = m_devget((char *)&wreq.wi_val, wreq.wi_len, 0,
ifp, NULL);
if (m != NULL)
IF_ENQUEUE(&ic->ic_mgtq, m);
else
error = ENOMEM;
Currently, each wireless networking driver has it's own control program despite the fact that most people want to set exactly the same settings regardless of which card they have. It has been repeatidly suggested that this configuration should be done via ifconfig. This patch implements the required functionality in ifconfig and add support to the wi and an drivers. It also provides partial, untested support for the awi driver. PR: 25577 Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
2001-05-26 09:27:08 +00:00
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
Currently, each wireless networking driver has it's own control program despite the fact that most people want to set exactly the same settings regardless of which card they have. It has been repeatidly suggested that this configuration should be done via ifconfig. This patch implements the required functionality in ifconfig and add support to the wi and an drivers. It also provides partial, untested support for the awi driver. PR: 25577 Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
2001-05-26 09:27:08 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_MIF:
mif = wreq.wi_val[0];
val = wreq.wi_val[1];
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_cmd(sc, WI_CMD_WRITEMIF, mif, val, 0);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
Currently, each wireless networking driver has it's own control program despite the fact that most people want to set exactly the same settings regardless of which card they have. It has been repeatidly suggested that this configuration should be done via ifconfig. This patch implements the required functionality in ifconfig and add support to the wi and an drivers. It also provides partial, untested support for the awi driver. PR: 25577 Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
2001-05-26 09:27:08 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_RID_PROCFRAME: /* ignore for compatibility */
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
case WI_RID_OWN_SSID:
if (le16toh(wreq.wi_val[0]) * 2 > len ||
le16toh(wreq.wi_val[0]) > IEEE80211_NWID_LEN) {
error = ENOSPC;
break;
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
memset(ic->ic_des_essid, 0, IEEE80211_NWID_LEN);
ic->ic_des_esslen = le16toh(wreq.wi_val[0]) * 2;
memcpy(ic->ic_des_essid, &wreq.wi_val[1], ic->ic_des_esslen);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (sc->sc_enabled)
wi_init(sc); /* XXX no error return */
WI_UNLOCK(sc);
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
break;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
default:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_LOCK(sc);
if (sc->sc_enabled)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_write_rid(sc, wreq.wi_type, wreq.wi_val,
len);
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (error == 0) {
/* XXX ieee80211_cfgset does a copyin */
error = ieee80211_cfgset(ic, cmd, data);
if (error == ENETRESET) {
if (sc->sc_enabled)
wi_init(sc);
error = 0;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
WI_UNLOCK(sc);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
break;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return error;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_write_txrate(struct wi_softc *sc)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct ieee80211com *ic = &sc->sc_ic;
int i;
u_int16_t rate;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
diff reduction against p4: define IEEE80211_FIXED_RATE_NONE and use it instead of -1
2005-07-22 16:50:18 +00:00
if (ic->ic_fixed_rate == IEEE80211_FIXED_RATE_NONE)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
rate = 0; /* auto */
else
update for new 802.11 support
2003-06-28 06:17:26 +00:00
rate = (ic->ic_sup_rates[IEEE80211_MODE_11B].rs_rates[ic->ic_fixed_rate] &
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
IEEE80211_RATE_VAL) / 2;
Modify wicontrol(8) and wi(4) to allow setting the frequency of the WaveLAN's radio modem. The default is whatever the NIC uses since NICs sold in different countries may default to different frequencies. (The Lose95/LoseNT software doesn't let you select the channel so it's probably not really meant to be changed.)
1999-05-06 16:32:45 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* rate: 0, 1, 2, 5, 11 */
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (sc->sc_firmware_type) {
case WI_LUCENT:
MFP4 27224 and 27225: Change 27224 by imp@imp_hammer on 2003/03/22 00:16:22 Put what I think are the correct TX RATE translation tables in place for LUCENT firmware. This is based on the 4.x driver. Maybe it should be table driven? ifconfig wi0 media DS/11Mbps still fails, but it fails before we even get to the txrate stuff, so other things are wrong. Change 27225 by imp@imp_hammer on 2003/03/22 00:45:11 Default ic_fixed_rate to -1. This is the same thing as autoselect. There really should be a #define for this...
2003-03-22 15:39:38 +00:00
switch (rate) {
case 0: /* auto == 11mbps auto */
rate = 3;
break;
/* case 1, 2 map to 1, 2*/
case 5: /* 5.5Mbps -> 4 */
rate = 4;
break;
case 11: /* 11mbps -> 5 */
rate = 5;
break;
default:
break;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
default:
/* Choose a bit according to this table.
*
* bit | data rate
* ----+-------------------
* 0 | 1Mbps
* 1 | 2Mbps
* 2 | 5.5Mbps
* 3 | 11Mbps
*/
for (i = 8; i > 0; i >>= 1) {
if (rate >= i)
break;
}
if (i == 0)
rate = 0xf; /* auto */
else
rate = i;
break;
}
return wi_write_val(sc, WI_RID_TX_RATE, rate);
}
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_write_wep(struct wi_softc *sc)
{
struct ieee80211com *ic = &sc->sc_ic;
int error = 0;
int i, keylen;
u_int16_t val;
struct wi_key wkey[IEEE80211_WEP_NKID];
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (sc->sc_firmware_type) {
case WI_LUCENT:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
val = (ic->ic_flags & IEEE80211_F_PRIVACY) ? 1 : 0;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_write_val(sc, WI_RID_ENCRYPTION, val);
if (error)
break;
Diff reduce wi_write_wep() relative to revision 1.168
2004-12-17 20:48:13 +00:00
if ((ic->ic_flags & IEEE80211_F_PRIVACY) == 0)
break;
error = wi_write_val(sc, WI_RID_TX_CRYPT_KEY, ic->ic_def_txkey);
if (error)
break;
memset(wkey, 0, sizeof(wkey));
for (i = 0; i < IEEE80211_WEP_NKID; i++) {
keylen = ic->ic_nw_keys[i].wk_keylen;
wkey[i].wi_keylen = htole16(keylen);
memcpy(wkey[i].wi_keydat, ic->ic_nw_keys[i].wk_key,
keylen);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Diff reduce wi_write_wep() relative to revision 1.168
2004-12-17 20:48:13 +00:00
error = wi_write_rid(sc, WI_RID_DEFLT_CRYPT_KEYS,
wkey, sizeof(wkey));
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
If we are in hostap mode, do not go into promisc mode. This causes problems with the firmware and will result in a) poor performance and b) the inability to associate certain types of cards (most notibly cisco). Idea obtained from OpenBSD, but I implemented it by clearing the IFF_PROMISC flag rather than the refusing to honor it downstream.
2002-07-29 15:36:22 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case WI_INTERSIL:
case WI_SYMBOL:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
if (ic->ic_flags & IEEE80211_F_PRIVACY) {
Add roaming and microwave oven support. Some minor formatting nits. Some buggy firmware workarounds. Fix some endian bugs. These reduce the diffs from NetBSD, but NetBSD does have more changes since my last manual merge.
2002-03-05 16:18:14 +00:00
/*
* ONLY HWB3163 EVAL-CARD Firmware version
Four fixes from NetBSD: 1) Properly detect the Symbol based cards (The 3Com Airconnect and their ilk) and only reset them *ONCE* ever. This appears to make them work, but more testing is needed. The tests that would wedge up my machine completely now appear to work, but I have not real access points handy. 2) Report both the Station firmware and the Primary firmware on Prism based cards. On Lucent based cards, only report the station firmware since that's all it supports. On symbol cards, report the symbol specific firmware name as its station firmware. 3) Better Prism 2.5 and 3 family names. We really need to go table driven for this. 4) Workaround for bugs in Intersil's firmware is only needed for at most 0.8.2 and earlier, since 0.8.3 and later appear to work. Obtained from: NetBSD
2002-04-03 19:44:17 +00:00
* less than 0.8 variant2
Add roaming and microwave oven support. Some minor formatting nits. Some buggy firmware workarounds. Fix some endian bugs. These reduce the diffs from NetBSD, but NetBSD does have more changes since my last manual merge.
2002-03-05 16:18:14 +00:00
*
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
* If promiscuous mode disable, Prism2 chip
* does not work with WEP .
Add roaming and microwave oven support. Some minor formatting nits. Some buggy firmware workarounds. Fix some endian bugs. These reduce the diffs from NetBSD, but NetBSD does have more changes since my last manual merge.
2002-03-05 16:18:14 +00:00
* It is under investigation for details.
* (ichiro@netbsd.org)
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (sc->sc_firmware_type == WI_INTERSIL &&
Four fixes from NetBSD: 1) Properly detect the Symbol based cards (The 3Com Airconnect and their ilk) and only reset them *ONCE* ever. This appears to make them work, but more testing is needed. The tests that would wedge up my machine completely now appear to work, but I have not real access points handy. 2) Report both the Station firmware and the Primary firmware on Prism based cards. On Lucent based cards, only report the station firmware since that's all it supports. On symbol cards, report the symbol specific firmware name as its station firmware. 3) Better Prism 2.5 and 3 family names. We really need to go table driven for this. 4) Workaround for bugs in Intersil's firmware is only needed for at most 0.8.2 and earlier, since 0.8.3 and later appear to work. Obtained from: NetBSD
2002-04-03 19:44:17 +00:00
sc->sc_sta_firmware_ver < 802 ) {
/* firm ver < 0.8 variant 2 */
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_write_val(sc, WI_RID_PROMISC, 1);
Add roaming and microwave oven support. Some minor formatting nits. Some buggy firmware workarounds. Fix some endian bugs. These reduce the diffs from NetBSD, but NetBSD does have more changes since my last manual merge.
2002-03-05 16:18:14 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_write_val(sc, WI_RID_CNFAUTHMODE,
sc->sc_cnfauthmode);
val = PRIVACY_INVOKED | EXCLUDE_UNENCRYPTED;
/*
* Encryption firmware has a bug for HostAP mode.
*/
if (sc->sc_firmware_type == WI_INTERSIL &&
ic->ic_opmode == IEEE80211_M_HOSTAP)
val |= HOST_ENCRYPT;
} else {
wi_write_val(sc, WI_RID_CNFAUTHMODE,
IEEE80211_AUTH_OPEN);
val = HOST_ENCRYPT | HOST_DECRYPT;
Add roaming and microwave oven support. Some minor formatting nits. Some buggy firmware workarounds. Fix some endian bugs. These reduce the diffs from NetBSD, but NetBSD does have more changes since my last manual merge.
2002-03-05 16:18:14 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_write_val(sc, WI_RID_P2_ENCRYPTION, val);
if (error)
break;
Diff reduce wi_write_wep() relative to revision 1.168
2004-12-17 20:48:13 +00:00
if ((val & PRIVACY_INVOKED) == 0)
break;
error = wi_write_val(sc, WI_RID_P2_TX_CRYPT_KEY,
ic->ic_def_txkey);
if (error)
break;
if (val & HOST_DECRYPT)
break;
/*
* It seems that the firmware accept 104bit key only if
* all the keys have 104bit length. We get the length of
* the transmit key and use it for all other keys.
* Perhaps we should use software WEP for such situation.
*/
if (ic->ic_def_txkey != IEEE80211_KEYIX_NONE)
keylen = ic->ic_nw_keys[ic->ic_def_txkey].wk_keylen;
else /* XXX should not hapen */
keylen = IEEE80211_WEP_KEYLEN;
if (keylen > IEEE80211_WEP_KEYLEN)
keylen = 13; /* 104bit keys */
else
keylen = IEEE80211_WEP_KEYLEN;
for (i = 0; i < IEEE80211_WEP_NKID; i++) {
error = wi_write_rid(sc, WI_RID_P2_CRYPT_KEY0 + i,
ic->ic_nw_keys[i].wk_key, keylen);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (error)
break;
}
break;
Add support for WEP (encryption) for silver and gold WaveLAN/IEEE turbo cards. Also update wicontrol to enable/disable encryption, set WEP keys and set the TX key index. Silver cards only have 40-bit keys. This is something of a quick hack, but it works well enough for me to commit this from the LinuxWorld exhibit floor. The WEP support only shows up if you have a card that supports it. Would have been approved by: jkh, if he hadn't wandered off somewhere Approved in his place by: msmith, who's standing right here
2000-02-02 17:59:13 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return error;
}
Add support for WEP (encryption) for silver and gold WaveLAN/IEEE turbo cards. Also update wicontrol to enable/disable encryption, set WEP keys and set the TX key index. Silver cards only have 40-bit keys. This is something of a quick hack, but it works well enough for me to commit this from the LinuxWorld exhibit floor. The WEP support only shows up if you have a card that supports it. Would have been approved by: jkh, if he hadn't wandered off somewhere Approved in his place by: msmith, who's standing right here
2000-02-02 17:59:13 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_cmd(struct wi_softc *sc, int cmd, int val0, int val1, int val2)
{
int i, s = 0;
static volatile int count = 0;
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
if (sc->wi_gone)
return (ENODEV);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (count > 0)
panic("Hey partner, hold on there!");
count++;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* wait for the busy bit to clear */
Older versions of the intersil firmware is a lot slower than newer versions of the firmware. It responds more slowly to commands, and we bogusly failed them. We assume that all versions of the intersil firmware before 1.0 are 10 times slower and will give it 10x the time to finish. # for 5.2 we should always just assume 5s.
2003-12-09 07:41:07 +00:00
for (i = sc->wi_cmd_count; i > 0; i--) { /* 500ms */
Minor tweaks that are effectively all style tweaks.
2003-06-11 16:51:27 +00:00
if (!(CSR_READ_2(sc, WI_COMMAND) & WI_CMD_BUSY))
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
break;
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
DELAY(1*1000); /* 1ms */
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
if (i == 0) {
device_printf(sc->sc_dev, "wi_cmd: busy bit won't clear.\n" );
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
sc->wi_gone = 1;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
count--;
return(ETIMEDOUT);
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
CSR_WRITE_2(sc, WI_PARAM0, val0);
CSR_WRITE_2(sc, WI_PARAM1, val1);
CSR_WRITE_2(sc, WI_PARAM2, val2);
CSR_WRITE_2(sc, WI_COMMAND, cmd);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (cmd == WI_CMD_INI) {
/* XXX: should sleep here. */
Minor tweaks that are effectively all style tweaks.
2003-06-11 16:51:27 +00:00
DELAY(100*1000); /* 100ms delay for init */
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
for (i = 0; i < WI_TIMEOUT; i++) {
/*
* Wait for 'command complete' bit to be
* set in the event status register.
*/
s = CSR_READ_2(sc, WI_EVENT_STAT);
if (s & WI_EV_CMD) {
/* Ack the event and read result code. */
s = CSR_READ_2(sc, WI_STATUS);
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_CMD);
if (s & WI_STAT_CMD_RESULT) {
count--;
return(EIO);
}
break;
}
DELAY(WI_DELAY);
}
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
count--;
if (i == WI_TIMEOUT) {
device_printf(sc->sc_dev,
"timeout in wi_cmd 0x%04x; event status 0x%04x\n", cmd, s);
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
if (s == 0xffff)
sc->wi_gone = 1;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return(ETIMEDOUT);
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return (0);
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_seek_bap(struct wi_softc *sc, int id, int off)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int i, status;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
CSR_WRITE_2(sc, WI_SEL0, id);
CSR_WRITE_2(sc, WI_OFF0, off);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
for (i = 0; ; i++) {
status = CSR_READ_2(sc, WI_OFF0);
if ((status & WI_OFF_BUSY) == 0)
break;
if (i == WI_TIMEOUT) {
device_printf(sc->sc_dev, "timeout in wi_seek to %x/%x\n",
id, off);
sc->sc_bap_off = WI_OFF_ERR; /* invalidate */
Fix Lucent cards. o Back out workaround for not resetting lucent cards more than once. With these fixes, it appaers they are no longer necessary. o Set wi_gone when the card goes awol: typically when we get 0xffff back from the card. Also, don't interact with a card that's gone, so we fail in seconds rather than minutes. Also reduce amount of time we wait to .5s in wi_cmd. o clear wi_gone on ifconfig down to give some cards a chance after they wedge (this appears to unwedge one of my prism cards with old firmware). ifconfig up will fail quickly enough if the card really is out to lunch. o Add delay in wi_init of 100ms. o wi_stop(ifp, 0->1) changes so that we clear sc_enabled so that we exit out of the interrupt routine by just acking the interrupt Submitted by: iedowse Approved by: re@ (scottl) # after the freeze I'll fix some of the minor style issues that reviewers # of this patch have told me about.
2003-12-02 04:59:59 +00:00
if (status == 0xffff)
sc->wi_gone = 1;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return ETIMEDOUT;
}
DELAY(1);
Update the wi driver to use mutexes instead of spls.
2000-10-13 20:33:24 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (status & WI_OFF_ERR) {
device_printf(sc->sc_dev, "failed in wi_seek to %x/%x\n", id, off);
sc->sc_bap_off = WI_OFF_ERR; /* invalidate */
return EIO;
Update the wi driver to use mutexes instead of spls.
2000-10-13 20:33:24 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_bap_id = id;
sc->sc_bap_off = off;
return 0;
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_read_bap(struct wi_softc *sc, int id, int off, void *buf, int buflen)
{
u_int16_t *ptr;
int i, error, cnt;
if (buflen == 0)
return 0;
if (id != sc->sc_bap_id || off != sc->sc_bap_off) {
if ((error = wi_seek_bap(sc, id, off)) != 0)
return error;
Update the wi driver to use mutexes instead of spls.
2000-10-13 20:33:24 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
cnt = (buflen + 1) / 2;
ptr = (u_int16_t *)buf;
for (i = 0; i < cnt; i++)
*ptr++ = CSR_READ_2(sc, WI_DATA0);
sc->sc_bap_off += cnt * 2;
return 0;
}
static int
wi_write_bap(struct wi_softc *sc, int id, int off, void *buf, int buflen)
{
u_int16_t *ptr;
int i, error, cnt;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (buflen == 0)
return 0;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#ifdef WI_HERMES_AUTOINC_WAR
again:
#endif
if (id != sc->sc_bap_id || off != sc->sc_bap_off) {
if ((error = wi_seek_bap(sc, id, off)) != 0)
return error;
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
cnt = (buflen + 1) / 2;
ptr = (u_int16_t *)buf;
for (i = 0; i < cnt; i++)
CSR_WRITE_2(sc, WI_DATA0, ptr[i]);
sc->sc_bap_off += cnt * 2;
#ifdef WI_HERMES_AUTOINC_WAR
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
/*
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
* According to the comments in the HCF Light code, there is a bug
* in the Hermes (or possibly in certain Hermes firmware revisions)
* where the chip's internal autoincrement counter gets thrown off
* during data writes: the autoincrement is missed, causing one
* data word to be overwritten and subsequent words to be written to
* the wrong memory locations. The end result is that we could end
* up transmitting bogus frames without realizing it. The workaround
* for this is to write a couple of extra guard words after the end
* of the transfer, then attempt to read then back. If we fail to
* locate the guard words where we expect them, we preform the
* transfer over again.
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if ((sc->sc_flags & WI_FLAGS_BUG_AUTOINC) && (id & 0xf000) == 0) {
CSR_WRITE_2(sc, WI_DATA0, 0x1234);
CSR_WRITE_2(sc, WI_DATA0, 0x5678);
wi_seek_bap(sc, id, sc->sc_bap_off);
sc->sc_bap_off = WI_OFF_ERR; /* invalidate */
if (CSR_READ_2(sc, WI_DATA0) != 0x1234 ||
CSR_READ_2(sc, WI_DATA0) != 0x5678) {
device_printf(sc->sc_dev,
"detect auto increment bug, try again\n");
goto again;
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#endif
return 0;
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_mwrite_bap(struct wi_softc *sc, int id, int off, struct mbuf *m0, int totlen)
{
int error, len;
struct mbuf *m;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
for (m = m0; m != NULL && totlen > 0; m = m->m_next) {
if (m->m_len == 0)
continue;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
len = min(m->m_len, totlen);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (((u_long)m->m_data) % 2 != 0 || len % 2 != 0) {
m_copydata(m, 0, totlen, (caddr_t)&sc->sc_txbuf);
return wi_write_bap(sc, id, off, (caddr_t)&sc->sc_txbuf,
totlen);
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if ((error = wi_write_bap(sc, id, off, m->m_data, len)) != 0)
return error;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
off += m->m_len;
totlen -= len;
}
return 0;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_alloc_fid(struct wi_softc *sc, int len, int *idp)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int i;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (wi_cmd(sc, WI_CMD_ALLOC_MEM, len, 0, 0)) {
device_printf(sc->sc_dev, "failed to allocate %d bytes on NIC\n",
len);
return ENOMEM;
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
for (i = 0; i < WI_TIMEOUT; i++) {
if (CSR_READ_2(sc, WI_EVENT_STAT) & WI_EV_ALLOC)
break;
DELAY(1);
}
correct logic so we recognize timeout on alloc Noticed by: Coverity Prevent analysis tool
2005-03-26 23:43:54 +00:00
if (i == WI_TIMEOUT) {
device_printf(sc->sc_dev, "timeout in alloc\n");
return ETIMEDOUT;
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
*idp = CSR_READ_2(sc, WI_ALLOC_FID);
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_ALLOC);
return 0;
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_read_rid(struct wi_softc *sc, int rid, void *buf, int *buflenp)
{
int error, len;
u_int16_t ltbuf[2];
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* Tell the NIC to enter record read mode. */
error = wi_cmd(sc, WI_CMD_ACCESS | WI_ACCESS_READ, rid, 0, 0);
if (error)
return error;
error = wi_read_bap(sc, rid, 0, ltbuf, sizeof(ltbuf));
if (error)
return error;
if (le16toh(ltbuf[1]) != rid) {
device_printf(sc->sc_dev, "record read mismatch, rid=%x, got=%x\n",
rid, le16toh(ltbuf[1]));
return EIO;
}
len = (le16toh(ltbuf[0]) - 1) * 2; /* already got rid */
if (*buflenp < len) {
device_printf(sc->sc_dev, "record buffer is too small, "
"rid=%x, size=%d, len=%d\n",
rid, *buflenp, len);
return ENOSPC;
}
*buflenp = len;
return wi_read_bap(sc, rid, sizeof(ltbuf), buf, len);
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
wi_write_rid(struct wi_softc *sc, int rid, void *buf, int buflen)
{
int error;
u_int16_t ltbuf[2];
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
ltbuf[0] = htole16((buflen + 1) / 2 + 1); /* includes rid */
ltbuf[1] = htole16(rid);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_write_bap(sc, rid, 0, ltbuf, sizeof(ltbuf));
if (error)
return error;
error = wi_write_bap(sc, rid, sizeof(ltbuf), buf, buflen);
if (error)
return error;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
return wi_cmd(sc, WI_CMD_ACCESS | WI_ACCESS_WRITE, rid, 0, 0);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
wi_newstate(struct ieee80211com *ic, enum ieee80211_state nstate, int arg)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
struct ifnet *ifp = ic->ic_ifp;
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
struct wi_softc *sc = ifp->if_softc;
Eliminate some of the egregious bypass of the 802.11 state machine; instead use the intended entry points. There's still too much incestuous knowledge about the internals of the 802.11 layer but this at least fixes adhoc mode.
2005-01-01 17:45:11 +00:00
struct ieee80211_node *ni;
update for new 802.11 support
2003-06-28 06:17:26 +00:00
int buflen;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
u_int16_t val;
struct wi_ssid ssid;
u_int8_t old_bssid[IEEE80211_ADDR_LEN];
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
DPRINTF(("%s: %s -> %s\n", __func__,
ieee80211_state_name[ic->ic_state],
ieee80211_state_name[nstate]));
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
Eliminate some of the egregious bypass of the 802.11 state machine; instead use the intended entry points. There's still too much incestuous knowledge about the internals of the 802.11 layer but this at least fixes adhoc mode.
2005-01-01 17:45:11 +00:00
/*
* Internal to the driver the INIT and RUN states are used
* so bypass the net80211 state machine for other states.
* Beware however that this requires use to net80211 state
* management that otherwise would be handled for us.
*/
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
switch (nstate) {
case IEEE80211_S_INIT:
sc->sc_flags &= ~WI_FLAGS_OUTRANGE;
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
return (*sc->sc_newstate)(ic, nstate, arg);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
case IEEE80211_S_SCAN:
case IEEE80211_S_AUTH:
case IEEE80211_S_ASSOC:
ic->ic_state = nstate; /* NB: skip normal ieee80211 handling */
break;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
case IEEE80211_S_RUN:
Eliminate some of the egregious bypass of the 802.11 state machine; instead use the intended entry points. There's still too much incestuous knowledge about the internals of the 802.11 layer but this at least fixes adhoc mode.
2005-01-01 17:45:11 +00:00
ni = ic->ic_bss;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_flags &= ~WI_FLAGS_OUTRANGE;
buflen = IEEE80211_ADDR_LEN;
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
IEEE80211_ADDR_COPY(old_bssid, ni->ni_bssid);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_read_rid(sc, WI_RID_CURRENT_BSSID, ni->ni_bssid, &buflen);
IEEE80211_ADDR_COPY(ni->ni_macaddr, ni->ni_bssid);
buflen = sizeof(val);
wi_read_rid(sc, WI_RID_CURRENT_CHAN, &val, &buflen);
update for new 802.11 support
2003-06-28 06:17:26 +00:00
/* XXX validate channel */
ni->ni_chan = &ic->ic_channels[le16toh(val)];
set ic_ibss_chan when entering RUN state to match ic_bss so the channel reported when associated to an AP is correct
2004-12-17 03:36:24 +00:00
ic->ic_ibss_chan = ni->ni_chan;
o add experimental radiotap capture format o add netbsd logic to convert rssi to device-independent values Obtained from: NetBSD (rssi conversion code)
2003-09-05 22:29:30 +00:00
#if NBPFILTER > 0
sc->sc_tx_th.wt_chan_freq = sc->sc_rx_th.wr_chan_freq =
htole16(ni->ni_chan->ic_freq);
sc->sc_tx_th.wt_chan_flags = sc->sc_rx_th.wr_chan_flags =
htole16(ni->ni_chan->ic_flags);
#endif
Eliminate some of the egregious bypass of the 802.11 state machine; instead use the intended entry points. There's still too much incestuous knowledge about the internals of the 802.11 layer but this at least fixes adhoc mode.
2005-01-01 17:45:11 +00:00
if (ic->ic_opmode != IEEE80211_M_HOSTAP) {
Fix wep operation for station mode: o don't encapsulate on tx; the chip expect a raw frame w/o the crypto header o clear the WEP bit in the 802.11 header on rx so the 802.11 layer doesn't try to strip the crypto header o clobber the "drop unencoded frames" state bit when privacy is enabled so rx'd frames we pass up to the 802.11 layer are not discarded as unencrypted This stuff will need to be redone if anyone decides to add WPA support.
2004-12-17 03:57:16 +00:00
/*
* XXX hack; unceremoniously clear
* IEEE80211_F_DROPUNENC when operating with
* wep enabled so we don't drop unencoded frames
* at the 802.11 layer. This is necessary because
* we must strip the WEP bit from the 802.11 header
* before passing frames to ieee80211_input because
* the card has already stripped the WEP crypto
* header from the packet.
*/
if (ic->ic_flags & IEEE80211_F_PRIVACY)
ic->ic_flags &= ~IEEE80211_F_DROPUNENC;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
/* XXX check return value */
buflen = sizeof(ssid);
wi_read_rid(sc, WI_RID_CURRENT_SSID, &ssid, &buflen);
ni->ni_esslen = le16toh(ssid.wi_len);
if (ni->ni_esslen > IEEE80211_NWID_LEN)
ni->ni_esslen = IEEE80211_NWID_LEN; /*XXX*/
memcpy(ni->ni_essid, ssid.wi_ssid, ni->ni_esslen);
}
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
return (*sc->sc_newstate)(ic, nstate, arg);
Update the wi driver to use mutexes instead of spls.
2000-10-13 20:33:24 +00:00
}
track changes to 802.11 code: o override new_state method per new model o use ieee80211_state_name instead of private copy
2003-07-20 21:38:20 +00:00
return 0;
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
Integrate the hostap stuff that Thomas Skibo <skibo@packbell.net> wrote. This code was for 4.5-release, so I've ported it to -current and made a few minor tweaks. The biggest non-style tweak was to not make access point the default. More changes will be needed to get this actually working, but I wanted to get a relatively pure baseline. This doesn't seem to break what works now.
2002-04-11 07:21:16 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static int
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
wi_scan_ap(struct wi_softc *sc, u_int16_t chanmask, u_int16_t txrate)
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
{
int error = 0;
u_int16_t val[2];
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (!sc->sc_enabled)
return ENXIO;
switch (sc->sc_firmware_type) {
case WI_LUCENT:
(void)wi_cmd(sc, WI_CMD_INQUIRE, WI_INFO_SCAN_RESULTS, 0, 0);
break;
case WI_INTERSIL:
o Update for net80211 changes o Import some minor fixes from netbsd
2004-12-08 17:36:28 +00:00
val[0] = htole16(chanmask); /* channel */
val[1] = htole16(txrate); /* tx rate */
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
error = wi_write_rid(sc, WI_RID_SCAN_REQ, val, sizeof(val));
break;
case WI_SYMBOL:
/*
* XXX only supported on 3.x ?
*/
val[0] = BSCAN_BCAST | BSCAN_ONETIME;
error = wi_write_rid(sc, WI_RID_BCAST_SCAN_REQ,
val, sizeof(val[0]));
break;
Attempt to read and verify the card's status in wi_stop() before sending it the disable command. On some systems, writing to the card after it has been ejected causes the machine to hang. Reviewed by: wpaul
2000-12-18 23:49:56 +00:00
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
if (error == 0) {
sc->sc_scan_timer = WI_SCAN_WAIT;
Stop embedding struct ifnet at the top of driver softcs. Instead the struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
2005-06-10 16:49:24 +00:00
sc->sc_ifp->if_timer = 1;
Return support needed by dstumbler: o add back rx monitor support o make WI_RID_SCAN_RES DTRT o fix a bug handling zero-length RID requests (used by dstumbler to set a zero-length SSID) o make RID_SCAN_REQ DTRT o add back WI_RID_OWN_SSID o fix wi_scan_ap to take a channel mask and txrate (for prism cards) These changes fix dstumbler -o (monitor mode). A minor change to dstumbler is needed to get normal AP scanning mode to work right; this is preferred to modifying the driver. PR: kern/53187 Reviewed by: Bruce M Simpson <bms@spc.org>
2003-06-27 00:49:04 +00:00
DPRINTF(("wi_scan_ap: start scanning, "
"chamask 0x%x txrate 0x%x\n", chanmask, txrate));
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
}
return error;
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
put function return types on a line by themselves as per style(9)
2001-12-27 20:12:03 +00:00
static void
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_scan_result(struct wi_softc *sc, int fid, int cnt)
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
#define N(a) (sizeof (a) / sizeof (a[0]))
int i, naps, off, szbuf;
struct wi_scan_header ws_hdr; /* Prism2 header */
struct wi_scan_data_p2 ws_dat; /* Prism2 scantable*/
struct wi_apinfo *ap;
off = sizeof(u_int16_t) * 2;
memset(&ws_hdr, 0, sizeof(ws_hdr));
switch (sc->sc_firmware_type) {
case WI_INTERSIL:
wi_read_bap(sc, fid, off, &ws_hdr, sizeof(ws_hdr));
off += sizeof(ws_hdr);
szbuf = sizeof(struct wi_scan_data_p2);
break;
case WI_SYMBOL:
szbuf = sizeof(struct wi_scan_data_p2) + 6;
break;
case WI_LUCENT:
szbuf = sizeof(struct wi_scan_data);
break;
default:
device_printf(sc->sc_dev,
"wi_scan_result: unknown firmware type %u\n",
sc->sc_firmware_type);
naps = 0;
goto done;
}
naps = (cnt * 2 + 2 - off) / szbuf;
if (naps > N(sc->sc_aps))
naps = N(sc->sc_aps);
sc->sc_naps = naps;
/* Read Data */
ap = sc->sc_aps;
memset(&ws_dat, 0, sizeof(ws_dat));
for (i = 0; i < naps; i++, ap++) {
wi_read_bap(sc, fid, off, &ws_dat,
(sizeof(ws_dat) < szbuf ? sizeof(ws_dat) : szbuf));
DPRINTF2(("wi_scan_result: #%d: off %d bssid %s\n", i, off,
ether_sprintf(ws_dat.wi_bssid)));
off += szbuf;
ap->scanreason = le16toh(ws_hdr.wi_reason);
memcpy(ap->bssid, ws_dat.wi_bssid, sizeof(ap->bssid));
ap->channel = le16toh(ws_dat.wi_chid);
ap->signal = le16toh(ws_dat.wi_signal);
ap->noise = le16toh(ws_dat.wi_noise);
ap->quality = ap->signal - ap->noise;
ap->capinfo = le16toh(ws_dat.wi_capinfo);
ap->interval = le16toh(ws_dat.wi_interval);
ap->rate = le16toh(ws_dat.wi_rate);
ap->namelen = le16toh(ws_dat.wi_namelen);
if (ap->namelen > sizeof(ap->name))
ap->namelen = sizeof(ap->name);
memcpy(ap->name, ws_dat.wi_name, ap->namelen);
}
done:
/* Done scanning */
sc->sc_scan_timer = 0;
DPRINTF(("wi_scan_result: scan complete: ap %d\n", naps));
#undef N
}
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
static void
wi_dump_pkt(struct wi_frame *wh, struct ieee80211_node *ni, int rssi)
{
ieee80211_dump_pkt((u_int8_t *) &wh->wi_whdr, sizeof(wh->wi_whdr),
update for new 802.11 support
2003-06-28 06:17:26 +00:00
ni ? ni->ni_rates.rs_rates[ni->ni_txrate] & IEEE80211_RATE_VAL : -1, rssi);
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
printf(" status 0x%x rx_tstamp1 %u rx_tstamp0 0x%u rx_silence %u\n",
le16toh(wh->wi_status), le16toh(wh->wi_rx_tstamp1),
le16toh(wh->wi_rx_tstamp0), wh->wi_rx_silence);
printf(" rx_signal %u rx_rate %u rx_flow %u\n",
wh->wi_rx_signal, wh->wi_rx_rate, wh->wi_rx_flow);
printf(" tx_rtry %u tx_rate %u tx_ctl 0x%x dat_len %u\n",
wh->wi_tx_rtry, wh->wi_tx_rate,
le16toh(wh->wi_tx_ctl), le16toh(wh->wi_dat_len));
printf(" ehdr dst %6D src %6D type 0x%x\n",
wh->wi_ehdr.ether_dhost, ":", wh->wi_ehdr.ether_shost, ":",
wh->wi_ehdr.ether_type);
Add device driver support for the Lucent WaveLAN/IEEE 802.11 wireless network adapters. These are all PCMCIA devices (the ISA version is a PCMCIA to ISA bridge with a PCMCIA card plugged into it). Also add a wicontrol utility to read and write some of the card's parameters. Note: I do not have access to a WavePOINT access point, so I have only been able to test this driver in ad-hoc (point to point) mode. The wicontrol utility allows programming the desired service set name (SSID) and enabling BSS mode, but I can't tell for sure if it works (I know the card switches modes, but I can't verify that it joins a service set correctly). This driver was written using information gleaned from the Lucent HCF Light library, which is an API library designed to simplify driver development for devices based on the Lucent Hermes chip. Unfortunately, the HCF Light is missing certain features (like 802.11 frame encapsulation!) which are available only in the proprietary complete HCF code, which is not available to the public. This driver uses none of the HCF Light code: it's very ugly and contaminated by the GPL. IP and ARP packets are encapsulated as 802.11 frames, everything else is encapsulated as 802.3. (It would be easier to just get the Hermes programming manual, but that's not publically available either. For those who are wondering, the Linux WaveLAN/IEEE driver uses the proprietary HCF code, which is provided in object code form only. So much for supporting open source sofware.) Multicast filter support is implemented, however it appears that the filter doesn't work: programming in one IP mutlicast group enables them all.
1999-05-05 07:11:38 +00:00
}
First cut at breaking out the bus attachment from the bus independent part of the driver. Also, move the softc and some other stuff to if_wivar.h from if_wireg.h to make future merging activities easier.
2002-04-02 02:38:35 +00:00
int
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_alloc(device_t dev, int rid)
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = device_get_softc(dev);
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
Add support for the Linksys WMP-11, Prism 2.5, PCI adaptor. Submitted by: Thomas Skibo <skibo@pacbell.net> MFC after: 2 weeks
2002-02-12 17:52:11 +00:00
if (sc->wi_bus_type != WI_BUS_PCI_NATIVE) {
sc->iobase_rid = rid;
sc->iobase = bus_alloc_resource(dev, SYS_RES_IOPORT,
&sc->iobase_rid, 0, ~0, (1 << 6),
rman_make_alignment_flags(1 << 6) | RF_ACTIVE);
if (!sc->iobase) {
device_printf(dev, "No I/O space?!\n");
return (ENXIO);
}
sc->wi_io_addr = rman_get_start(sc->iobase);
sc->wi_btag = rman_get_bustag(sc->iobase);
sc->wi_bhandle = rman_get_bushandle(sc->iobase);
} else {
sc->mem_rid = rid;
Convert callers to the new bus_alloc_resource_any(9) API. Submitted by: Mark Santcroos <marks@ripe.net> Reviewed by: imp, dfr, bde
2004-03-17 17:50:55 +00:00
sc->mem = bus_alloc_resource_any(dev, SYS_RES_MEMORY,
&sc->mem_rid, RF_ACTIVE);
Add support for the Linksys WMP-11, Prism 2.5, PCI adaptor. Submitted by: Thomas Skibo <skibo@pacbell.net> MFC after: 2 weeks
2002-02-12 17:52:11 +00:00
if (!sc->mem) {
device_printf(dev, "No Mem space on prism2.5?\n");
return (ENXIO);
}
sc->wi_btag = rman_get_bustag(sc->mem);
sc->wi_bhandle = rman_get_bushandle(sc->mem);
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
}
Add support for the Linksys WMP-11, Prism 2.5, PCI adaptor. Submitted by: Thomas Skibo <skibo@pacbell.net> MFC after: 2 weeks
2002-02-12 17:52:11 +00:00
Add support for the Addtron AWA100 PCI wireless card. The AWA100 is a PCI board with a PLX 9052 chip that's used to talk to the pccard inserted into the board. Remove a redundant $FreeBSD while I'm here.
2001-03-28 05:05:05 +00:00
sc->irq_rid = 0;
Convert callers to the new bus_alloc_resource_any(9) API. Submitted by: Mark Santcroos <marks@ripe.net> Reviewed by: imp, dfr, bde
2004-03-17 17:50:55 +00:00
sc->irq = bus_alloc_resource_any(dev, SYS_RES_IRQ, &sc->irq_rid,
RF_ACTIVE |
Add support for the Linksys WMP-11, Prism 2.5, PCI adaptor. Submitted by: Thomas Skibo <skibo@pacbell.net> MFC after: 2 weeks
2002-02-12 17:52:11 +00:00
((sc->wi_bus_type == WI_BUS_PCCARD) ? 0 : RF_SHAREABLE));
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
if (!sc->irq) {
Don't leak resources: Don't leak iospace when irq allocation fails. (call wi_free()) Call bus_release_resource() with the correct "rid" obtained from bus_alloc_resource() that's saved in the softc instead of a hardcoded 0.
2001-04-05 06:56:10 +00:00
wi_free(dev);
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
device_printf(dev, "No irq?!\n");
return (ENXIO);
}
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
sc->sc_dev = dev;
sc->sc_unit = device_get_unit(dev);
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
return (0);
}
First cut at breaking out the bus attachment from the bus independent part of the driver. Also, move the softc and some other stuff to if_wivar.h from if_wireg.h to make future merging activities easier.
2002-04-02 02:38:35 +00:00
void
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_free(device_t dev)
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
struct wi_softc *sc = device_get_softc(dev);
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
Don't leak resources: Don't leak iospace when irq allocation fails. (call wi_free()) Call bus_release_resource() with the correct "rid" obtained from bus_alloc_resource() that's saved in the softc instead of a hardcoded 0.
2001-04-05 06:56:10 +00:00
if (sc->iobase != NULL) {
bus_release_resource(dev, SYS_RES_IOPORT, sc->iobase_rid, sc->iobase);
sc->iobase = NULL;
}
if (sc->irq != NULL) {
bus_release_resource(dev, SYS_RES_IRQ, sc->irq_rid, sc->irq);
sc->irq = NULL;
}
if (sc->mem != NULL) {
Add support for the Addtron AWA100 PCI wireless card. The AWA100 is a PCI board with a PLX 9052 chip that's used to talk to the pccard inserted into the board. Remove a redundant $FreeBSD while I'm here.
2001-03-28 05:05:05 +00:00
bus_release_resource(dev, SYS_RES_MEMORY, sc->mem_rid, sc->mem);
Don't leak resources: Don't leak iospace when irq allocation fails. (call wi_free()) Call bus_release_resource() with the correct "rid" obtained from bus_alloc_resource() that's saved in the softc instead of a hardcoded 0.
2001-04-05 06:56:10 +00:00
sc->mem = NULL;
}
Update the WaveLAN/IEEE driver: - Convert to new bus attachment scheme. Thanks to Blaz Zupan for doing the initial work here. One thing I changed was to have the attach and detach routines work like the PCI drivers, which means that in theory you should be able to load and unload the driver like the PCI NIC drivers, however the pccard support for this hasn't settled down yet so it doesn't quite work. Once the pccard work is done, I'll have to revisit this. - Add device wi0 to PCCARD. If we're lucky, people should be able to install via their WaveLAN cards now. - Add support for signal strength caching. The wicontrol utility has also been updated to allow zeroing and displaying the signal strength cache. - Add a /sys/modules/wi directory and fix a Makefile to builf if_wi.ko. Currently this module is only built for the i386 platform, though once the pccard stuff is done it should be able to work on the alpha too. (Theoretically you should be able to plug one of the WaveLAN/IEEE ISA cards into an alpha with an ISA slot, but we'll see how that turns out. - Update LINT to use only device wi0. There is no true ISA version of the WaveLAN/IEEE so we'll never use an ISA attachment. - Update files.i386 so that if_wi is dependent on card.
1999-11-25 20:45:49 +00:00
return;
}
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
static int
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_get_debug(struct wi_softc *sc, struct wi_req *wreq)
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int error = 0;
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
wreq->wi_len = 1;
switch (wreq->wi_type) {
case WI_DEBUG_SLEEP:
wreq->wi_len++;
wreq->wi_val[0] = sc->wi_debug.wi_sleep;
break;
case WI_DEBUG_DELAYSUPP:
wreq->wi_len++;
wreq->wi_val[0] = sc->wi_debug.wi_delaysupp;
break;
case WI_DEBUG_TXSUPP:
wreq->wi_len++;
wreq->wi_val[0] = sc->wi_debug.wi_txsupp;
break;
case WI_DEBUG_MONITOR:
wreq->wi_len++;
wreq->wi_val[0] = sc->wi_debug.wi_monitor;
break;
case WI_DEBUG_LEDTEST:
wreq->wi_len += 3;
wreq->wi_val[0] = sc->wi_debug.wi_ledtest;
wreq->wi_val[1] = sc->wi_debug.wi_ledtest_param0;
wreq->wi_val[2] = sc->wi_debug.wi_ledtest_param1;
break;
case WI_DEBUG_CONTTX:
wreq->wi_len += 2;
wreq->wi_val[0] = sc->wi_debug.wi_conttx;
wreq->wi_val[1] = sc->wi_debug.wi_conttx_param0;
break;
case WI_DEBUG_CONTRX:
wreq->wi_len++;
wreq->wi_val[0] = sc->wi_debug.wi_contrx;
break;
case WI_DEBUG_SIGSTATE:
wreq->wi_len += 2;
wreq->wi_val[0] = sc->wi_debug.wi_sigstate;
wreq->wi_val[1] = sc->wi_debug.wi_sigstate_param0;
break;
case WI_DEBUG_CONFBITS:
wreq->wi_len += 2;
wreq->wi_val[0] = sc->wi_debug.wi_confbits;
wreq->wi_val[1] = sc->wi_debug.wi_confbits_param0;
break;
default:
error = EIO;
break;
}
return (error);
}
static int
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
wi_set_debug(struct wi_softc *sc, struct wi_req *wreq)
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
{
new wi driver that uses the 802.11 link layer code Reviewed by: imp Obtained from: NetBSD (originally)
2003-01-15 20:11:31 +00:00
int error = 0;
Integrate the air-tools 0.2 from dachb0den labs. o This moves the common.h file into if_wavelan_ieee.h Submitted by: h1kari@dachb0den.com
2002-03-29 00:26:23 +00:00
u_int16_t cmd, param0 = 0, param1 = 0;
switch (wreq->wi_type) {
case WI_DEBUG_RESET:
case WI_DEBUG_INIT:
case WI_DEBUG_CALENABLE:
break;
case WI_DEBUG_SLEEP:
sc->wi_debug.wi_sleep = 1;
break;
case WI_DEBUG_WAKE:
sc->wi_debug.wi_sleep = 0;
break;
case WI_DEBUG_CHAN:
param0 = wreq->wi_val[0];
break;
case WI_DEBUG_DELAYSUPP:
sc->wi_debug.wi_delaysupp = 1;
break;
case WI_DEBUG_TXSUPP:
sc->wi_debug.wi_txsupp = 1;
break;
case WI_DEBUG_MONITOR:
sc->wi_debug.wi_monitor = 1;
break;
case WI_DEBUG_LEDTEST:
param0 = wreq->wi_val[0];
param1 = wreq->wi_val[1];
sc->wi_debug.wi_ledtest = 1;
sc->wi_debug.wi_ledtest_param0 = param0;
sc->wi_debug.wi_ledtest_param1 = param1;
break;
case WI_DEBUG_CONTTX:
param0 = wreq->wi_val[0];
sc->wi_debug.wi_conttx = 1;
sc->wi_debug.wi_conttx_param0 = param0;
break;
case WI_DEBUG_STOPTEST:
sc->wi_debug.wi_delaysupp = 0;
sc->wi_debug.wi_txsupp = 0;
sc->wi_debug.wi_monitor = 0;
sc->wi_debug.wi_ledtest = 0;
sc->wi_debug.wi_ledtest_param0 = 0;
sc->wi_debug.wi_ledtest_param1 = 0;
sc->wi_debug.wi_conttx = 0;
sc->wi_debug.wi_conttx_param0 = 0;
sc->wi_debug.wi_contrx = 0;
sc->wi_debug.wi_sigstate = 0;
sc->wi_debug.wi_sigstate_param0 = 0;
break;
case WI_DEBUG_CONTRX:
sc->wi_debug.wi_contrx = 1;
break;
case WI_DEBUG_SIGSTATE:
param0 = wreq->wi_val[0];
sc->wi_debug.wi_sigstate = 1;
sc->wi_debug.wi_sigstate_param0 = param0;
break;
case WI_DEBUG_CONFBITS:
param0 = wreq->wi_val[0];
param1 = wreq->wi_val[1];
sc->wi_debug.wi_confbits = param0;
sc->wi_debug.wi_confbits_param0 = param1;
break;
default:
error = EIO;
break;
}
if (error)
return (error);
cmd = WI_CMD_DEBUG | (wreq->wi_type << 8);
error = wi_cmd(sc, cmd, param0, param1, 0);
return (error);
}
Move the symbol firmware loading routines into if_wi. Define some basic firmware downloading commands.
2002-08-15 07:13:17 +00:00
o Comment out the symbol download code for 4.x. o Add hooks for doing power management of the output signal. o Minor hacks to make flexlint happy wrt staticness of functions.
2002-10-14 01:59:57 +00:00
#if __FreeBSD_version >= 500000
Move the symbol firmware loading routines into if_wi. Define some basic firmware downloading commands.
2002-08-15 07:13:17 +00:00
/*
* Special routines to download firmware for Symbol CF card.
* XXX: This should be modified generic into any PRISM-2 based card.
*/
#define WI_SBCF_PDIADDR 0x3100
/* unaligned load little endian */
#define GETLE32(p) ((p)[0] | ((p)[1]<<8) | ((p)[2]<<16) | ((p)[3]<<24))
#define GETLE16(p) ((p)[0] | ((p)[1]<<8))
int
wi_symbol_load_firm(struct wi_softc *sc, const void *primsym, int primlen,
const void *secsym, int seclen)
{
uint8_t ebuf[256];
int i;
/* load primary code and run it */
wi_symbol_set_hcr(sc, WI_HCR_EEHOLD);
if (wi_symbol_write_firm(sc, primsym, primlen, NULL, 0))
return EIO;
wi_symbol_set_hcr(sc, WI_HCR_RUN);
for (i = 0; ; i++) {
if (i == 10)
return ETIMEDOUT;
tsleep(sc, PWAIT, "wiinit", 1);
if (CSR_READ_2(sc, WI_CNTL) == WI_CNTL_AUX_ENA_STAT)
break;
/* write the magic key value to unlock aux port */
CSR_WRITE_2(sc, WI_PARAM0, WI_AUX_KEY0);
CSR_WRITE_2(sc, WI_PARAM1, WI_AUX_KEY1);
CSR_WRITE_2(sc, WI_PARAM2, WI_AUX_KEY2);
CSR_WRITE_2(sc, WI_CNTL, WI_CNTL_AUX_ENA_CNTL);
}
/* issue read EEPROM command: XXX copied from wi_cmd() */
CSR_WRITE_2(sc, WI_PARAM0, 0);
CSR_WRITE_2(sc, WI_PARAM1, 0);
CSR_WRITE_2(sc, WI_PARAM2, 0);
CSR_WRITE_2(sc, WI_COMMAND, WI_CMD_READEE);
for (i = 0; i < WI_TIMEOUT; i++) {
if (CSR_READ_2(sc, WI_EVENT_STAT) & WI_EV_CMD)
break;
DELAY(1);
}
CSR_WRITE_2(sc, WI_EVENT_ACK, WI_EV_CMD);
CSR_WRITE_2(sc, WI_AUX_PAGE, WI_SBCF_PDIADDR / WI_AUX_PGSZ);
CSR_WRITE_2(sc, WI_AUX_OFFSET, WI_SBCF_PDIADDR % WI_AUX_PGSZ);
CSR_READ_MULTI_STREAM_2(sc, WI_AUX_DATA,
(uint16_t *)ebuf, sizeof(ebuf) / 2);
if (GETLE16(ebuf) > sizeof(ebuf))
return EIO;
if (wi_symbol_write_firm(sc, secsym, seclen, ebuf + 4, GETLE16(ebuf)))
return EIO;
return 0;
}
static int
wi_symbol_write_firm(struct wi_softc *sc, const void *buf, int buflen,
const void *ebuf, int ebuflen)
{
const uint8_t *p, *ep, *q, *eq;
char *tp;
uint32_t addr, id, eid;
int i, len, elen, nblk, pdrlen;
/*
* Parse the header of the firmware image.
*/
p = buf;
ep = p + buflen;
while (p < ep && *p++ != ' '); /* FILE: */
while (p < ep && *p++ != ' '); /* filename */
while (p < ep && *p++ != ' '); /* type of the firmware */
nblk = strtoul(p, &tp, 10);
p = tp;
pdrlen = strtoul(p + 1, &tp, 10);
p = tp;
while (p < ep && *p++ != 0x1a); /* skip rest of header */
/*
* Block records: address[4], length[2], data[length];
*/
for (i = 0; i < nblk; i++) {
addr = GETLE32(p); p += 4;
len = GETLE16(p); p += 2;
CSR_WRITE_2(sc, WI_AUX_PAGE, addr / WI_AUX_PGSZ);
CSR_WRITE_2(sc, WI_AUX_OFFSET, addr % WI_AUX_PGSZ);
CSR_WRITE_MULTI_STREAM_2(sc, WI_AUX_DATA,
(const uint16_t *)p, len / 2);
p += len;
}
/*
* PDR: id[4], address[4], length[4];
*/
for (i = 0; i < pdrlen; ) {
id = GETLE32(p); p += 4; i += 4;
addr = GETLE32(p); p += 4; i += 4;
len = GETLE32(p); p += 4; i += 4;
/* replace PDR entry with the values from EEPROM, if any */
for (q = ebuf, eq = q + ebuflen; q < eq; q += elen * 2) {
elen = GETLE16(q); q += 2;
eid = GETLE16(q); q += 2;
elen--; /* elen includes eid */
if (eid == 0)
break;
if (eid != id)
continue;
CSR_WRITE_2(sc, WI_AUX_PAGE, addr / WI_AUX_PGSZ);
CSR_WRITE_2(sc, WI_AUX_OFFSET, addr % WI_AUX_PGSZ);
CSR_WRITE_MULTI_STREAM_2(sc, WI_AUX_DATA,
(const uint16_t *)q, len / 2);
break;
}
}
return 0;
}
static int
wi_symbol_set_hcr(struct wi_softc *sc, int mode)
{
uint16_t hcr;
CSR_WRITE_2(sc, WI_COR, WI_COR_RESET);
tsleep(sc, PWAIT, "wiinit", 1);
hcr = CSR_READ_2(sc, WI_HCR);
hcr = (hcr & WI_HCR_4WIRE) | (mode & ~WI_HCR_4WIRE);
CSR_WRITE_2(sc, WI_HCR, hcr);
tsleep(sc, PWAIT, "wiinit", 1);
CSR_WRITE_2(sc, WI_COR, WI_COR_IOMODE);
tsleep(sc, PWAIT, "wiinit", 1);
return 0;
}
o Comment out the symbol download code for 4.x. o Add hooks for doing power management of the output signal. o Minor hacks to make flexlint happy wrt staticness of functions.
2002-10-14 01:59:57 +00:00
#endif
Reference in New Issue Copy Permalink