d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
a89409b817
freebsd-nq/sys/dev/mii/tlphy.c

375 lines
9.9 KiB
C
Raw Normal View History

Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
/* $NetBSD: tlphy.c,v 1.18 1999/05/14 11:40:28 drochner Exp $ */
/*-
* Copyright (c) 1998, 1999 The NetBSD Foundation, Inc.
* All rights reserved.
*
* This code is derived from software contributed to The NetBSD Foundation
* by Jason R. Thorpe of the Numerical Aerospace Simulation Facility,
* NASA Ames Research Center.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
* TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
* PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
Start each of the license/copyright comments with /*-, minor shuffle of lines
2005-01-06 01:43:34 +00:00
/*-
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
* Copyright (c) 1997 Manuel Bouyer. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
Remove double __FBSDID and move the remaining one into a common place after the license(s) and before the driver comment (the latter only in drivers not having __FBSDID at that location).
2004-05-29 18:09:10 +00:00
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
/*
* Driver for Texas Instruments's ThunderLAN PHYs
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/errno.h>
#include <sys/module.h>
#include <sys/bus.h>
Add includes of sys/malloc.h so this actually compiles. Pointy-hat to: asmodai
2001-02-09 00:16:41 +00:00
#include <sys/malloc.h>
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
#include <machine/bus.h>
#include <net/if.h>
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
Remove miidevs.h and generate it from miidevs at compile time. The devlist2h.awk tool to do this has been repocopied to sys/tools/.
2003-01-19 02:59:34 +00:00
#include "miidevs.h"
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
#include <dev/mii/tlphyreg.h>
#include "miibus_if.h"
struct tlphy_softc {
struct mii_softc sc_mii; /* generic PHY */
int sc_need_acomp;
};
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int tlphy_probe(device_t);
static int tlphy_attach(device_t);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
static device_method_t tlphy_methods[] = {
/* device interface */
DEVMETHOD(device_probe, tlphy_probe),
DEVMETHOD(device_attach, tlphy_attach),
Make one generic mii_phy_detach() to replace 19 slightly different ones. Rename mii_phy_auto_stop() mii_phy_down(). Introduce mii_down(), use it from nge. Do not indirect it to 19 identical case's in 19 switchstatements like NetBSD did.
2002-04-29 13:07:38 +00:00
DEVMETHOD(device_detach, mii_phy_detach),
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
DEVMETHOD(device_shutdown, bus_generic_shutdown),
Use DEVMETHOD_END.
2011-11-23 20:27:26 +00:00
DEVMETHOD_END
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
};
static devclass_t tlphy_devclass;
static driver_t tlphy_driver = {
"tlphy",
tlphy_methods,
sizeof(struct tlphy_softc)
};
DRIVER_MODULE(tlphy, miibus, tlphy_driver, tlphy_devclass, 0, 0);
Remove __P.
2002-03-20 02:08:01 +00:00
static int tlphy_service(struct mii_softc *, struct mii_data *, int);
Clean up mii/phy drivers: Remove the MIIF_DOINGAUTO which doesn't really do anything at the end of the day except bloat the drivers which has copy&pasted it.
2002-05-04 11:00:30 +00:00
static int tlphy_auto(struct tlphy_softc *);
Remove __P.
2002-03-20 02:08:01 +00:00
static void tlphy_acomp(struct tlphy_softc *);
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
static void tlphy_status(struct mii_softc *);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
Add a helper function mii_phy_dev_probe(), which wraps around the mii_phy_match() API and takes care of the PHY device probe based on the struct mii_phydesc array and the match return value provided. Convert PHY drivers to take advantage of mii_phy_dev_probe(), converting drivers to provide a mii_phydesc table in the first place where necessary. Reviewed by: yongari MFC after: 2 weeks
2006-12-02 15:32:34 +00:00
static const struct mii_phydesc tlphys[] = {
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MII_PHY_DESC(TI, TLAN10T),
Add a helper function mii_phy_dev_probe(), which wraps around the mii_phy_match() API and takes care of the PHY device probe based on the struct mii_phydesc array and the match return value provided. Convert PHY drivers to take advantage of mii_phy_dev_probe(), converting drivers to provide a mii_phydesc table in the first place where necessary. Reviewed by: yongari MFC after: 2 weeks
2006-12-02 15:32:34 +00:00
MII_PHY_END
};
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
static const struct mii_phy_funcs tlphy_funcs = {
tlphy_service,
tlphy_status,
mii_phy_reset
};
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
tlphy_probe(device_t dev)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
{
In miibus(4) drivers provide functions that allow to get NIC driver name and NIC driver softc via the device(9) tree, instead of going dirty through the ifnet(9) layer. Differential Revision: D1506 Reviewed by: imp, jhb
2015-01-12 22:27:38 +00:00
if (!mii_dev_mac_match(dev, "tl"))
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
return (ENXIO);
Add a helper function mii_phy_dev_probe(), which wraps around the mii_phy_match() API and takes care of the PHY device probe based on the struct mii_phydesc array and the match return value provided. Convert PHY drivers to take advantage of mii_phy_dev_probe(), converting drivers to provide a mii_phydesc table in the first place where necessary. Reviewed by: yongari MFC after: 2 weeks
2006-12-02 15:32:34 +00:00
return (mii_phy_dev_probe(dev, tlphys, BUS_PROBE_DEFAULT));
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
}
Put function return types on a line by themselves. Cleanup my earlier de-__P sweep and remove whitespace between function names and paramters.
2002-10-14 22:31:52 +00:00
static int
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
tlphy_attach(device_t dev)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
{
Some style changes to a couple of PHY drivers: - Fix some whitespace nits. - Fix some spelling in comments. - Use MII_ANEGTICKS instead of 5. - Don't define variables in nested scope. - Remove superfluous returns at the end of void functions. - Remove unused static global rgephy_mii_model. - Remove dupe $Id$ in tdkphy(4). - Sort brgphys table. MFC after: 2 weeks
2006-12-02 19:36:25 +00:00
device_t *devlist;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
struct mii_softc *other, *sc_mii;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
const char *sep = "";
Some style changes to a couple of PHY drivers: - Fix some whitespace nits. - Fix some spelling in comments. - Use MII_ANEGTICKS instead of 5. - Don't define variables in nested scope. - Remove superfluous returns at the end of void functions. - Remove unused static global rgephy_mii_model. - Remove dupe $Id$ in tdkphy(4). - Sort brgphys table. MFC after: 2 weeks
2006-12-02 19:36:25 +00:00
int capmask, devs, i;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
sc_mii = device_get_softc(dev);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
mii_phy_dev_attach(dev, MIIF_NOMANPAUSE, &tlphy_funcs, 0);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
/*
* Note that if we're on a device that also supports 100baseTX,
* we are not going to want to use the built-in 10baseT port,
* since there will be another PHY on the MII wired up to the
* UTP connector.
*/
Convert the PHY drivers to honor the mii_flags passed down and convert the NIC drivers as well as the PHY drivers to take advantage of the mii_attach() introduced in r213878 to get rid of certain hacks. For the most part these were: - Artificially limiting miibus_{read,write}reg methods to certain PHY addresses; we now let mii_attach() only probe the PHY at the desired address(es) instead. - PHY drivers setting MIIF_* flags based on the NIC driver they hang off from, partly even based on grabbing and using the softc of the parent; we now pass these flags down from the NIC to the PHY drivers via mii_attach(). This got us rid of all such hacks except those of brgphy() in combination with bce(4) and bge(4), which is way beyond what can be expressed with simple flags. While at it, I took the opportunity to change the NIC drivers to pass up the error returned by mii_attach() (previously by mii_phy_probe()) and unify the error message used in this case where and as appropriate as mii_attach() actually can fail for a number of reasons, not just because of no PHY(s) being present at the expected address(es). Reviewed by: jhb, yongari
2010-10-15 14:52:11 +00:00
capmask = BMSR_DEFCAPMASK;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if (sc_mii->mii_inst &&
device_get_children(sc_mii->mii_dev, &devlist, &devs) == 0) {
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
for (i = 0; i < devs; i++) {
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
if (devlist[i] != dev) {
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
other = device_get_softc(devlist[i]);
capmask &= ~other->mii_capabilities;
break;
}
}
Fix memoryleaks with device_get_children(). Approved by: wpaul
2001-02-08 21:53:05 +00:00
free(devlist, M_TEMP);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
}
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
PHY_RESET(sc_mii);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
sc_mii->mii_capabilities = PHY_READ(sc_mii, MII_BMSR) & capmask;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
#define ADD(m, c) \
ifmedia_add(&sc_mii->mii_pdata->mii_media, (m), (c), NULL)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
#define PRINT(s) printf("%s%s", sep, s); sep = ", "
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if ((sc_mii->mii_flags & (MIIF_MACPRIV0 | MIIF_MACPRIV1)) != 0 &&
(sc_mii->mii_capabilities & BMSR_MEDIAMASK) != 0)
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
device_printf(dev, " ");
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if ((sc_mii->mii_flags & MIIF_MACPRIV0) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_2, 0, sc_mii->mii_inst),
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
0);
PRINT("10base2/BNC");
}
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if ((sc_mii->mii_flags & MIIF_MACPRIV1) != 0) {
ADD(IFM_MAKEWORD(IFM_ETHER, IFM_10_5, 0, sc_mii->mii_inst),
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
0);
PRINT("10base5/AUI");
}
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if ((sc_mii->mii_capabilities & BMSR_MEDIAMASK) != 0) {
Quiet a variable format-string warning. MFC after: 1 week
2001-07-19 02:16:24 +00:00
printf("%s", sep);
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
mii_phy_add_media(sc_mii);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
}
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
if ((sc_mii->mii_flags & (MIIF_MACPRIV0 | MIIF_MACPRIV1)) != 0 &&
(sc_mii->mii_capabilities & BMSR_MEDIAMASK) != 0)
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
printf("\n");
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
#undef ADD
#undef PRINT
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
MIIBUS_MEDIAINIT(sc_mii->mii_dev);
Some style changes to a couple of PHY drivers: - Fix some whitespace nits. - Fix some spelling in comments. - Use MII_ANEGTICKS instead of 5. - Don't define variables in nested scope. - Remove superfluous returns at the end of void functions. - Remove unused static global rgephy_mii_model. - Remove dupe $Id$ in tdkphy(4). - Sort brgphys table. MFC after: 2 weeks
2006-12-02 19:36:25 +00:00
return (0);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static int
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
tlphy_service(struct mii_softc *self, struct mii_data *mii, int cmd)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
{
struct tlphy_softc *sc = (struct tlphy_softc *)self;
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
int reg;
Clean up mii/phy drivers: Remove the MIIF_DOINGAUTO which doesn't really do anything at the end of the day except bloat the drivers which has copy&pasted it.
2002-05-04 11:00:30 +00:00
if (sc->sc_need_acomp)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
tlphy_acomp(sc);
switch (cmd) {
case MII_POLLSTAT:
break;
case MII_MEDIACHG:
switch (IFM_SUBTYPE(ife->ifm_media)) {
case IFM_AUTO:
/*
* The ThunderLAN PHY doesn't self-configure after
* an autonegotiation cycle, so there's no such
* thing as "already in auto mode".
*/
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
(void)tlphy_auto(sc);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
break;
case IFM_10_2:
case IFM_10_5:
PHY_WRITE(&sc->sc_mii, MII_BMCR, 0);
PHY_WRITE(&sc->sc_mii, MII_TLPHY_CTRL, CTRL_AUISEL);
DELAY(100000);
break;
default:
PHY_WRITE(&sc->sc_mii, MII_TLPHY_CTRL, 0);
DELAY(100000);
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
mii_phy_setmedia(&sc->sc_mii);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
}
break;
case MII_TICK:
/*
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
* Only used for autonegotiation.
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
*/
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO)
break;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
/*
* Check to see if we have link. If we do, we don't
* need to restart the autonegotiation process. Read
* the BMSR twice in case it's latched.
*
* XXX WHAT ABOUT CHECKING LINK ON THE BNC/AUI?!
*/
reg = PHY_READ(&sc->sc_mii, MII_BMSR) |
PHY_READ(&sc->sc_mii, MII_BMSR);
if (reg & BMSR_LINK)
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
break;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
/*
* Only retry autonegotiation every 5 seconds.
*/
Some style changes to a couple of PHY drivers: - Fix some whitespace nits. - Fix some spelling in comments. - Use MII_ANEGTICKS instead of 5. - Don't define variables in nested scope. - Remove superfluous returns at the end of void functions. - Remove unused static global rgephy_mii_model. - Remove dupe $Id$ in tdkphy(4). - Sort brgphys table. MFC after: 2 weeks
2006-12-02 19:36:25 +00:00
if (++sc->sc_mii.mii_ticks <= MII_ANEGTICKS)
Correct the phy_service() routine case MII_TICK to correctly track the falling edge of a media state change. This is in preparation for media state change notification to the routing socket. No objections by: sam, wpaul, ru, bms Brucification by: bde
2004-05-03 13:01:34 +00:00
break;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
sc->sc_mii.mii_ticks = 0;
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
PHY_RESET(&sc->sc_mii);
- Add IFM_10_2 and IFM_10_5 media via tlphy(4) only in case the respective interface also has such connectors. - In tl_attach() unify three different ways of obtaining the device and vendor IDs and remove the now obsolete tl_dinfo from tl_softc. - Given that tlphy(4) only handles the integrated PHYs of NICs driven by tl(4) make it only probe on the latter. - Switch mlphy(4) and tlphy(4) to use mii_phy_add_media()/mii_phy_setmedia(). - Simplify looking for the respective companion PHY in mlphy(4) and tlphy(4) by ignoring the native one by just comparing the device_t's directly rather than the device name.
2010-10-24 12:51:02 +00:00
(void)tlphy_auto(sc);
Clean up mii/phy drivers: Remove the MIIF_DOINGAUTO which doesn't really do anything at the end of the day except bloat the drivers which has copy&pasted it.
2002-05-04 11:00:30 +00:00
return (0);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
}
/* Update the media status. */
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
PHY_STATUS(self);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
/* Callback if something changed. */
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
mii_phy_update(&sc->sc_mii, cmd);
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
return (0);
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static void
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
tlphy_status(struct mii_softc *self)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
{
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
struct tlphy_softc *sc = (struct tlphy_softc *)self;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
struct mii_data *mii = sc->sc_mii.mii_pdata;
int bmsr, bmcr, tlctrl;
mii->mii_media_status = IFM_AVALID;
mii->mii_media_active = IFM_ETHER;
bmcr = PHY_READ(&sc->sc_mii, MII_BMCR);
if (bmcr & BMCR_ISO) {
mii->mii_media_active |= IFM_NONE;
Some style changes to a couple of PHY drivers: - Fix some whitespace nits. - Fix some spelling in comments. - Use MII_ANEGTICKS instead of 5. - Don't define variables in nested scope. - Remove superfluous returns at the end of void functions. - Remove unused static global rgephy_mii_model. - Remove dupe $Id$ in tdkphy(4). - Sort brgphys table. MFC after: 2 weeks
2006-12-02 19:36:25 +00:00
mii->mii_media_status = 0;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
return;
}
tlctrl = PHY_READ(&sc->sc_mii, MII_TLPHY_CTRL);
if (tlctrl & CTRL_AUISEL) {
mii->mii_media_status = 0;
mii->mii_media_active = mii->mii_media.ifm_cur->ifm_media;
return;
}
bmsr = PHY_READ(&sc->sc_mii, MII_BMSR) |
PHY_READ(&sc->sc_mii, MII_BMSR);
Some style changes to a couple of PHY drivers: - Fix some whitespace nits. - Fix some spelling in comments. - Use MII_ANEGTICKS instead of 5. - Don't define variables in nested scope. - Remove superfluous returns at the end of void functions. - Remove unused static global rgephy_mii_model. - Remove dupe $Id$ in tdkphy(4). - Sort brgphys table. MFC after: 2 weeks
2006-12-02 19:36:25 +00:00
if (bmsr & BMSR_LINK)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
mii->mii_media_status |= IFM_ACTIVE;
if (bmcr & BMCR_LOOP)
mii->mii_media_active |= IFM_LOOP;
/*
* Grr, braindead ThunderLAN PHY doesn't have any way to
* tell which media is actually active. (Note it also
* doesn't self-configure after autonegotiation.) We
* just have to report what's in the BMCR.
*/
if (bmcr & BMCR_FDX)
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
mii->mii_media_active |= IFM_FDX | mii_phy_flowstatus(self);
Consistently always explicitly set IFM_HDX for half-duplex. Obtained from: OpenBSD (mostly)
2010-10-03 17:00:57 +00:00
else
mii->mii_media_active |= IFM_HDX;
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
mii->mii_media_active |= IFM_10_T;
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static int
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
tlphy_auto(struct tlphy_softc *sc)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
{
int error;
Clean up mii/phy drivers: Remove the MIIF_DOINGAUTO which doesn't really do anything at the end of the day except bloat the drivers which has copy&pasted it.
2002-05-04 11:00:30 +00:00
switch ((error = mii_phy_auto(&sc->sc_mii))) {
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
case EIO:
/*
* Just assume we're not in full-duplex mode.
* XXX Check link and try AUI/BNC?
*/
PHY_WRITE(&sc->sc_mii, MII_BMCR, 0);
break;
case EJUSTRETURN:
/* Flag that we need to program when it completes. */
sc->sc_need_acomp = 1;
break;
default:
tlphy_acomp(sc);
}
return (error);
}
Cleanup pass for mii drivers. . Make internal service routines static. . Use a consistent ordering of checks in MII_TICK. Do the work in the mii_phy_tick() subroutine if appropriate. . Call mii_phy_update() to trigger the callbacks.
2001-09-29 19:18:52 +00:00
static void
Use ansi function definitions in preference to K&R to reduce diffs with NetBSD (and cause it looks cooler).
2005-09-30 19:39:27 +00:00
tlphy_acomp(struct tlphy_softc *sc)
Add miibus drivers for the ThunderLAN internal PHY and the Micro Linear ML6692 PHY. The Micro Linear driver is my own; the ThunderLAN driver is a port of the NetBSD driver with various hacks. The ML driver is necessary to support the Olicom OC-2326 ThunderLAN-based NIC. Also regenerated miidevs.h to pick up the proper 'obtained from' revision string.
1999-08-27 18:33:36 +00:00
{
int aner, anlpar;
sc->sc_need_acomp = 0;
/*
* Grr, braindead ThunderLAN PHY doesn't self-configure
* after autonegotiation. We have to do it ourselves
* based on the link partner status.
*/
aner = PHY_READ(&sc->sc_mii, MII_ANER);
if (aner & ANER_LPAN) {
anlpar = PHY_READ(&sc->sc_mii, MII_ANLPAR) &
PHY_READ(&sc->sc_mii, MII_ANAR);
if (anlpar & ANAR_10_FD) {
PHY_WRITE(&sc->sc_mii, MII_BMCR, BMCR_FDX);
return;
}
}
PHY_WRITE(&sc->sc_mii, MII_BMCR, 0);
}
Reference in New Issue Copy Permalink