2005-01-06 01:43:34 +00:00
|
|
|
/*-
|
2004-09-10 20:57:46 +00:00
|
|
|
* Copyright (c) 2004
|
|
|
|
|
* Bill Paul <wpaul@windriver.com>. All rights reserved.
|
|
|
|
|
*
|
|
|
|
|
* Redistribution and use in source and binary forms, with or without
|
|
|
|
|
* modification, are permitted provided that the following conditions
|
|
|
|
|
* are met:
|
|
|
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
|
|
|
* notice, this list of conditions and the following disclaimer.
|
|
|
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
|
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
|
|
|
* documentation and/or other materials provided with the distribution.
|
|
|
|
|
* 3. All advertising materials mentioning features or use of this software
|
|
|
|
|
* must display the following acknowledgement:
|
|
|
|
|
* This product includes software developed by Bill Paul.
|
|
|
|
|
* 4. Neither the name of the author nor the names of any co-contributors
|
|
|
|
|
* may be used to endorse or promote products derived from this software
|
|
|
|
|
* without specific prior written permission.
|
|
|
|
|
*
|
|
|
|
|
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
|
|
|
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
|
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
|
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
|
|
|
|
|
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
|
|
|
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
|
|
|
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
|
|
|
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
|
|
|
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
|
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
|
|
|
|
|
* THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#include <sys/cdefs.h>
|
|
|
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
|
|
|
|
|
|
/*
|
2008-04-26 18:07:24 +00:00
|
|
|
* Driver for the Cicada/Vitesse CS/VSC8xxx 10/100/1000 copper PHY.
|
2004-09-10 20:57:46 +00:00
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#include <sys/param.h>
|
|
|
|
|
#include <sys/systm.h>
|
|
|
|
|
#include <sys/kernel.h>
|
|
|
|
|
#include <sys/module.h>
|
|
|
|
|
#include <sys/socket.h>
|
|
|
|
|
#include <sys/bus.h>
|
|
|
|
|
|
|
|
|
|
#include <net/if.h>
|
|
|
|
|
#include <net/if_arp.h>
|
|
|
|
|
#include <net/if_media.h>
|
|
|
|
|
|
|
|
|
|
#include <dev/mii/mii.h>
|
|
|
|
|
#include <dev/mii/miivar.h>
|
|
|
|
|
#include "miidevs.h"
|
|
|
|
|
|
|
|
|
|
#include <dev/mii/ciphyreg.h>
|
|
|
|
|
|
|
|
|
|
#include "miibus_if.h"
|
|
|
|
|
|
|
|
|
|
#include <machine/bus.h>
|
2010-10-15 14:52:11 +00:00
|
|
|
|
2004-09-10 20:57:46 +00:00
|
|
|
static int ciphy_probe(device_t);
|
|
|
|
|
static int ciphy_attach(device_t);
|
|
|
|
|
|
|
|
|
|
static device_method_t ciphy_methods[] = {
|
|
|
|
|
/* device interface */
|
|
|
|
|
DEVMETHOD(device_probe, ciphy_probe),
|
|
|
|
|
DEVMETHOD(device_attach, ciphy_attach),
|
|
|
|
|
DEVMETHOD(device_detach, mii_phy_detach),
|
|
|
|
|
DEVMETHOD(device_shutdown, bus_generic_shutdown),
|
2011-11-23 20:27:26 +00:00
|
|
|
DEVMETHOD_END
|
2004-09-10 20:57:46 +00:00
|
|
|
};
|
|
|
|
|
|
|
|
|
|
static devclass_t ciphy_devclass;
|
|
|
|
|
|
|
|
|
|
static driver_t ciphy_driver = {
|
|
|
|
|
"ciphy",
|
|
|
|
|
ciphy_methods,
|
|
|
|
|
sizeof(struct mii_softc)
|
|
|
|
|
};
|
|
|
|
|
|
|
|
|
|
DRIVER_MODULE(ciphy, miibus, ciphy_driver, ciphy_devclass, 0, 0);
|
|
|
|
|
|
|
|
|
|
static int ciphy_service(struct mii_softc *, struct mii_data *, int);
|
|
|
|
|
static void ciphy_status(struct mii_softc *);
|
|
|
|
|
static void ciphy_reset(struct mii_softc *);
|
|
|
|
|
static void ciphy_fixup(struct mii_softc *);
|
|
|
|
|
|
2006-12-02 15:32:34 +00:00
|
|
|
static const struct mii_phydesc ciphys[] = {
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
MII_PHY_DESC(xxCICADA, CS8201),
|
|
|
|
|
MII_PHY_DESC(xxCICADA, CS8201A),
|
|
|
|
|
MII_PHY_DESC(xxCICADA, CS8201B),
|
|
|
|
|
MII_PHY_DESC(xxCICADA, CS8204),
|
|
|
|
|
MII_PHY_DESC(xxCICADA, VSC8211),
|
2012-05-25 15:05:17 +00:00
|
|
|
MII_PHY_DESC(xxCICADA, VSC8221),
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
MII_PHY_DESC(xxCICADA, CS8244),
|
|
|
|
|
MII_PHY_DESC(xxVITESSE, VSC8601),
|
2012-05-25 15:05:17 +00:00
|
|
|
MII_PHY_DESC(xxVITESSE, VSC8641),
|
2006-12-02 15:32:34 +00:00
|
|
|
MII_PHY_END
|
|
|
|
|
};
|
|
|
|
|
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
static const struct mii_phy_funcs ciphy_funcs = {
|
|
|
|
|
ciphy_service,
|
|
|
|
|
ciphy_status,
|
|
|
|
|
ciphy_reset
|
|
|
|
|
};
|
|
|
|
|
|
2004-09-10 20:57:46 +00:00
|
|
|
static int
|
2005-09-30 19:39:27 +00:00
|
|
|
ciphy_probe(device_t dev)
|
2004-09-10 20:57:46 +00:00
|
|
|
{
|
|
|
|
|
|
2006-12-02 15:32:34 +00:00
|
|
|
return (mii_phy_dev_probe(dev, ciphys, BUS_PROBE_DEFAULT));
|
2004-09-10 20:57:46 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static int
|
2005-09-30 19:39:27 +00:00
|
|
|
ciphy_attach(device_t dev)
|
2004-09-10 20:57:46 +00:00
|
|
|
{
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
|
|
|
|
|
mii_phy_dev_attach(dev, MIIF_NOISOLATE | MIIF_NOMANPAUSE,
|
|
|
|
|
&ciphy_funcs, 1);
|
2006-11-28 00:43:38 +00:00
|
|
|
return (0);
|
2004-09-10 20:57:46 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static int
|
2005-09-30 19:39:27 +00:00
|
|
|
ciphy_service(struct mii_softc *sc, struct mii_data *mii, int cmd)
|
2004-09-10 20:57:46 +00:00
|
|
|
{
|
|
|
|
|
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
|
|
|
|
|
int reg, speed, gig;
|
|
|
|
|
|
|
|
|
|
switch (cmd) {
|
|
|
|
|
case MII_POLLSTAT:
|
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
case MII_MEDIACHG:
|
|
|
|
|
ciphy_fixup(sc); /* XXX hardware bug work-around */
|
|
|
|
|
|
|
|
|
|
switch (IFM_SUBTYPE(ife->ifm_media)) {
|
|
|
|
|
case IFM_AUTO:
|
|
|
|
|
#ifdef foo
|
|
|
|
|
/*
|
|
|
|
|
* If we're already in auto mode, just return.
|
|
|
|
|
*/
|
|
|
|
|
if (PHY_READ(sc, CIPHY_MII_BMCR) & CIPHY_BMCR_AUTOEN)
|
|
|
|
|
return (0);
|
|
|
|
|
#endif
|
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control
support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
|
|
|
(void)mii_phy_auto(sc);
|
2004-09-10 20:57:46 +00:00
|
|
|
break;
|
|
|
|
|
case IFM_1000_T:
|
|
|
|
|
speed = CIPHY_S1000;
|
|
|
|
|
goto setit;
|
|
|
|
|
case IFM_100_TX:
|
|
|
|
|
speed = CIPHY_S100;
|
|
|
|
|
goto setit;
|
|
|
|
|
case IFM_10_T:
|
|
|
|
|
speed = CIPHY_S10;
|
|
|
|
|
setit:
|
2011-01-14 19:29:53 +00:00
|
|
|
if ((ife->ifm_media & IFM_FDX) != 0) {
|
2004-09-10 20:57:46 +00:00
|
|
|
speed |= CIPHY_BMCR_FDX;
|
|
|
|
|
gig = CIPHY_1000CTL_AFD;
|
2011-01-14 19:29:53 +00:00
|
|
|
} else
|
2004-09-10 20:57:46 +00:00
|
|
|
gig = CIPHY_1000CTL_AHD;
|
|
|
|
|
|
2011-01-14 19:29:53 +00:00
|
|
|
if (IFM_SUBTYPE(ife->ifm_media) == IFM_1000_T) {
|
|
|
|
|
gig |= CIPHY_1000CTL_MSE;
|
|
|
|
|
if ((ife->ifm_media & IFM_ETH_MASTER) != 0)
|
|
|
|
|
gig |= CIPHY_1000CTL_MSC;
|
|
|
|
|
speed |=
|
|
|
|
|
CIPHY_BMCR_AUTOEN | CIPHY_BMCR_STARTNEG;
|
|
|
|
|
} else
|
|
|
|
|
gig = 0;
|
|
|
|
|
PHY_WRITE(sc, CIPHY_MII_1000CTL, gig);
|
2004-09-10 20:57:46 +00:00
|
|
|
PHY_WRITE(sc, CIPHY_MII_BMCR, speed);
|
|
|
|
|
PHY_WRITE(sc, CIPHY_MII_ANAR, CIPHY_SEL_TYPE);
|
|
|
|
|
break;
|
|
|
|
|
case IFM_NONE:
|
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control
support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
|
|
|
PHY_WRITE(sc, MII_BMCR, BMCR_ISO | BMCR_PDOWN);
|
2004-09-10 20:57:46 +00:00
|
|
|
break;
|
|
|
|
|
default:
|
|
|
|
|
return (EINVAL);
|
|
|
|
|
}
|
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
case MII_TICK:
|
|
|
|
|
/*
|
|
|
|
|
* Only used for autonegotiation.
|
|
|
|
|
*/
|
|
|
|
|
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO)
|
|
|
|
|
break;
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Check to see if we have link. If we do, we don't
|
|
|
|
|
* need to restart the autonegotiation process. Read
|
|
|
|
|
* the BMSR twice in case it's latched.
|
|
|
|
|
*/
|
|
|
|
|
reg = PHY_READ(sc, MII_BMSR) | PHY_READ(sc, MII_BMSR);
|
|
|
|
|
if (reg & BMSR_LINK)
|
|
|
|
|
break;
|
|
|
|
|
|
2008-09-30 07:19:01 +00:00
|
|
|
/* Announce link loss right after it happens. */
|
|
|
|
|
if (++sc->mii_ticks == 0)
|
|
|
|
|
break;
|
2004-09-10 20:57:46 +00:00
|
|
|
/*
|
2008-09-30 07:20:26 +00:00
|
|
|
* Only retry autonegotiation every mii_anegticks seconds.
|
2004-09-10 20:57:46 +00:00
|
|
|
*/
|
2008-09-30 07:20:26 +00:00
|
|
|
if (sc->mii_ticks <= sc->mii_anegticks)
|
2004-09-10 20:57:46 +00:00
|
|
|
break;
|
2006-11-28 00:43:38 +00:00
|
|
|
|
2004-09-10 20:57:46 +00:00
|
|
|
sc->mii_ticks = 0;
|
|
|
|
|
mii_phy_auto(sc);
|
2008-09-30 07:22:02 +00:00
|
|
|
break;
|
2004-09-10 20:57:46 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* Update the media status. */
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
PHY_STATUS(sc);
|
2004-09-10 20:57:46 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Callback if something changed. Note that we need to poke
|
|
|
|
|
* apply fixups for certain PHY revs.
|
|
|
|
|
*/
|
2006-11-28 00:43:38 +00:00
|
|
|
if (sc->mii_media_active != mii->mii_media_active ||
|
2004-09-10 20:57:46 +00:00
|
|
|
sc->mii_media_status != mii->mii_media_status ||
|
|
|
|
|
cmd == MII_MEDIACHG) {
|
|
|
|
|
ciphy_fixup(sc);
|
|
|
|
|
}
|
|
|
|
|
mii_phy_update(sc, cmd);
|
|
|
|
|
return (0);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static void
|
2005-09-30 19:39:27 +00:00
|
|
|
ciphy_status(struct mii_softc *sc)
|
2004-09-10 20:57:46 +00:00
|
|
|
{
|
|
|
|
|
struct mii_data *mii = sc->mii_pdata;
|
|
|
|
|
int bmsr, bmcr;
|
|
|
|
|
|
|
|
|
|
mii->mii_media_status = IFM_AVALID;
|
|
|
|
|
mii->mii_media_active = IFM_ETHER;
|
|
|
|
|
|
|
|
|
|
bmsr = PHY_READ(sc, MII_BMSR) | PHY_READ(sc, MII_BMSR);
|
|
|
|
|
|
|
|
|
|
if (bmsr & BMSR_LINK)
|
|
|
|
|
mii->mii_media_status |= IFM_ACTIVE;
|
|
|
|
|
|
|
|
|
|
bmcr = PHY_READ(sc, CIPHY_MII_BMCR);
|
|
|
|
|
|
|
|
|
|
if (bmcr & CIPHY_BMCR_LOOP)
|
|
|
|
|
mii->mii_media_active |= IFM_LOOP;
|
|
|
|
|
|
|
|
|
|
if (bmcr & CIPHY_BMCR_AUTOEN) {
|
|
|
|
|
if ((bmsr & CIPHY_BMSR_ACOMP) == 0) {
|
|
|
|
|
/* Erg, still trying, I guess... */
|
|
|
|
|
mii->mii_media_active |= IFM_NONE;
|
|
|
|
|
return;
|
|
|
|
|
}
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
bmsr = PHY_READ(sc, CIPHY_MII_AUXCSR);
|
|
|
|
|
switch (bmsr & CIPHY_AUXCSR_SPEED) {
|
|
|
|
|
case CIPHY_SPEED10:
|
|
|
|
|
mii->mii_media_active |= IFM_10_T;
|
|
|
|
|
break;
|
|
|
|
|
case CIPHY_SPEED100:
|
|
|
|
|
mii->mii_media_active |= IFM_100_TX;
|
|
|
|
|
break;
|
|
|
|
|
case CIPHY_SPEED1000:
|
|
|
|
|
mii->mii_media_active |= IFM_1000_T;
|
|
|
|
|
break;
|
|
|
|
|
default:
|
|
|
|
|
device_printf(sc->mii_dev, "unknown PHY speed %x\n",
|
|
|
|
|
bmsr & CIPHY_AUXCSR_SPEED);
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
if (bmsr & CIPHY_AUXCSR_FDX)
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
mii->mii_media_active |= IFM_FDX | mii_phy_flowstatus(sc);
|
2008-09-30 07:24:20 +00:00
|
|
|
else
|
|
|
|
|
mii->mii_media_active |= IFM_HDX;
|
o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control
support in mii(4):
- Merge generic flow control advertisement (which can be enabled by
passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
IFM_FLOW isn't implemented as a global option via the "don't care
mask" but instead as a media specific option this. This has the
following advantages:
o allows flow control advertisement with autonegotiation to be
turned on and off via ifconfig(8) with the default typically
being off (though MIIF_FORCEPAUSE has been added causing flow
control to be always advertised, allowing to easily MFC this
changes for drivers that previously used home-grown support for
flow control that behaved that way without breaking POLA)
o allows to deal with PHY drivers where flow control advertisement
with manual selection doesn't work or at least isn't implemented,
like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
by setting MIIF_NOMANPAUSE
o the available combinations of media options are readily available
from the `ifconfig -m` output
- Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
- Change IFM_ETH_MASTER from being implemented as a global option via
the "don't care mask" to a media specific one as it actually is only
applicable to IFM_1000_T to date.
- Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
actually configure manually selected slave mode (like we also do in
the PHY specific implementations).
- Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
e1000phy(4) and ip1000phy(4) to use the generic flow control support
instead of home-grown solutions via IFM_FLAGs. This includes changing
these PHY drivers and smcphy(4) to no longer unconditionally advertise
support for flow control but only if the selected media has IFM_FLOW
set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
the contents of the BMSR via mii_phy_add_media() instead of hardcoding
them. The latter approach seems to have developed historically, besides
causing unnecessary code duplication it was also undesirable because
brgphy_mii_phy_auto() already based the capability advertisement on the
contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
just BCM5701. Apparently this was a misinterpretation of a workaround
in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
this doesn't mean we can't set these as well on other PHYs for manual
media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
IFM_1000_T master mode support now is generally available with all PHY
drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
not applicable there.
Reviewed by: yongari (plus additional testing)
Obtained from: NetBSD (partially), OpenBSD (partially)
MFC after: 2 weeks
2010-11-14 13:26:10 +00:00
|
|
|
|
|
|
|
|
if ((IFM_SUBTYPE(mii->mii_media_active) == IFM_1000_T) &&
|
|
|
|
|
(PHY_READ(sc, CIPHY_MII_1000STS) & CIPHY_1000STS_MSR) != 0)
|
|
|
|
|
mii->mii_media_active |= IFM_ETH_MASTER;
|
2004-09-10 20:57:46 +00:00
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static void
|
|
|
|
|
ciphy_reset(struct mii_softc *sc)
|
|
|
|
|
{
|
2006-12-02 19:36:25 +00:00
|
|
|
|
2004-09-10 20:57:46 +00:00
|
|
|
mii_phy_reset(sc);
|
|
|
|
|
DELAY(1000);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
#define PHY_SETBIT(x, y, z) \
|
|
|
|
|
PHY_WRITE(x, y, (PHY_READ(x, y) | (z)))
|
|
|
|
|
#define PHY_CLRBIT(x, y, z) \
|
|
|
|
|
PHY_WRITE(x, y, (PHY_READ(x, y) & ~(z)))
|
|
|
|
|
|
|
|
|
|
static void
|
|
|
|
|
ciphy_fixup(struct mii_softc *sc)
|
|
|
|
|
{
|
|
|
|
|
uint16_t model;
|
|
|
|
|
uint16_t status, speed;
|
2007-06-06 06:55:49 +00:00
|
|
|
uint16_t val;
|
2004-09-10 20:57:46 +00:00
|
|
|
|
|
|
|
|
model = MII_MODEL(PHY_READ(sc, CIPHY_MII_PHYIDR2));
|
|
|
|
|
status = PHY_READ(sc, CIPHY_MII_AUXCSR);
|
|
|
|
|
speed = status & CIPHY_AUXCSR_SPEED;
|
|
|
|
|
|
2007-06-06 06:55:49 +00:00
|
|
|
if (strcmp(device_get_name(device_get_parent(sc->mii_dev)),
|
|
|
|
|
"nfe") == 0) {
|
|
|
|
|
/* need to set for 2.5V RGMII for NVIDIA adapters */
|
|
|
|
|
val = PHY_READ(sc, CIPHY_MII_ECTL1);
|
|
|
|
|
val &= ~(CIPHY_ECTL1_IOVOL | CIPHY_ECTL1_INTSEL);
|
|
|
|
|
val |= (CIPHY_IOVOL_2500MV | CIPHY_INTSEL_RGMII);
|
|
|
|
|
PHY_WRITE(sc, CIPHY_MII_ECTL1, val);
|
|
|
|
|
/* From Linux. */
|
|
|
|
|
val = PHY_READ(sc, CIPHY_MII_AUXCSR);
|
|
|
|
|
val |= CIPHY_AUXCSR_MDPPS;
|
|
|
|
|
PHY_WRITE(sc, CIPHY_MII_AUXCSR, val);
|
|
|
|
|
val = PHY_READ(sc, CIPHY_MII_10BTCSR);
|
|
|
|
|
val |= CIPHY_10BTCSR_ECHO;
|
|
|
|
|
PHY_WRITE(sc, CIPHY_MII_10BTCSR, val);
|
|
|
|
|
}
|
|
|
|
|
|
2004-09-10 20:57:46 +00:00
|
|
|
switch (model) {
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
case MII_MODEL_xxCICADA_CS8204:
|
|
|
|
|
case MII_MODEL_xxCICADA_CS8201:
|
2004-09-10 20:57:46 +00:00
|
|
|
|
|
|
|
|
/* Turn off "aux mode" (whatever that means) */
|
|
|
|
|
PHY_SETBIT(sc, CIPHY_MII_AUXCSR, CIPHY_AUXCSR_MDPPS);
|
|
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Work around speed polling bug in VT3119/VT3216
|
|
|
|
|
* when using MII in full duplex mode.
|
|
|
|
|
*/
|
|
|
|
|
if ((speed == CIPHY_SPEED10 || speed == CIPHY_SPEED100) &&
|
|
|
|
|
(status & CIPHY_AUXCSR_FDX)) {
|
|
|
|
|
PHY_SETBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
|
|
|
|
|
} else {
|
|
|
|
|
PHY_CLRBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
/* Enable link/activity LED blink. */
|
|
|
|
|
PHY_SETBIT(sc, CIPHY_MII_LED, CIPHY_LED_LINKACTBLINK);
|
|
|
|
|
|
|
|
|
|
break;
|
|
|
|
|
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
case MII_MODEL_xxCICADA_CS8201A:
|
|
|
|
|
case MII_MODEL_xxCICADA_CS8201B:
|
2004-09-10 20:57:46 +00:00
|
|
|
|
|
|
|
|
/*
|
|
|
|
|
* Work around speed polling bug in VT3119/VT3216
|
|
|
|
|
* when using MII in full duplex mode.
|
|
|
|
|
*/
|
|
|
|
|
if ((speed == CIPHY_SPEED10 || speed == CIPHY_SPEED100) &&
|
|
|
|
|
(status & CIPHY_AUXCSR_FDX)) {
|
|
|
|
|
PHY_SETBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
|
|
|
|
|
} else {
|
|
|
|
|
PHY_CLRBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
|
|
|
|
|
}
|
|
|
|
|
|
2007-06-06 06:55:49 +00:00
|
|
|
break;
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
case MII_MODEL_xxCICADA_VSC8211:
|
2012-05-25 15:05:17 +00:00
|
|
|
case MII_MODEL_xxCICADA_VSC8221:
|
- Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOP
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
2011-05-03 19:51:29 +00:00
|
|
|
case MII_MODEL_xxCICADA_CS8244:
|
|
|
|
|
case MII_MODEL_xxVITESSE_VSC8601:
|
2012-05-25 15:05:17 +00:00
|
|
|
case MII_MODEL_xxVITESSE_VSC8641:
|
2004-09-10 20:57:46 +00:00
|
|
|
break;
|
|
|
|
|
default:
|
|
|
|
|
device_printf(sc->mii_dev, "unknown CICADA PHY model %x\n",
|
|
|
|
|
model);
|
|
|
|
|
break;
|
|
|
|
|
}
|
|
|
|
|
}
|
