d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
c9f78537bc
freebsd-nq/sys/dev/ath/if_ath_misc.h

116 lines
4.4 KiB
C
Raw Normal View History

Migrate the TX path code out of if_ath and into a separate source file. There's two reasons for this: * the raw and non-raw TX path shares a lot of duplicate code which should be refactored; * the 11n-ready chip TX path needs a little reworking.
2011-01-29 11:35:23 +00:00
/*-
* Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
* redistribution must be conditioned upon including a substantially
* similar Disclaimer requirement for further binary redistribution.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
* AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
* THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
* OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
* IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGES.
*
* $FreeBSD$
*/
#ifndef __IF_ATH_MISC_H__
#define __IF_ATH_MISC_H__
/*
* This is where definitions for "public things" in if_ath.c
* will go for the time being.
*
* Anything in here should eventually be moved out of if_ath.c
* and into something else.
*/
/* unaligned little endian access */
#define LE_READ_2(p) \
((u_int16_t) \
((((u_int8_t *)(p))[0] ) | (((u_int8_t *)(p))[1] << 8)))
#define LE_READ_4(p) \
((u_int32_t) \
((((u_int8_t *)(p))[0] ) | (((u_int8_t *)(p))[1] << 8) | \
(((u_int8_t *)(p))[2] << 16) | (((u_int8_t *)(p))[3] << 24)))
Further preparations for the RX EDMA support. Break out the DMA descriptor setup/teardown code into a method. The EDMA RX code doesn't allocate descriptors, just ath_buf entries.
2012-07-09 08:37:59 +00:00
extern int ath_rxbuf;
extern int ath_txbuf;
extern int ath_txbuf_mgmt;
Migrate the TX path code out of if_ath and into a separate source file. There's two reasons for this: * the raw and non-raw TX path shares a lot of duplicate code which should be refactored; * the 11n-ready chip TX path needs a little reworking.
2011-01-29 11:35:23 +00:00
extern int ath_tx_findrix(const struct ath_softc *sc, uint8_t rate);
Implement a separate, smaller pool of ath_buf entries for use by management traffic. * Create sc_mgmt_txbuf and sc_mgmt_txdesc, initialise/free them appropriately. * Create an enum to represent buffer types in the API. * Extend ath_getbuf() and _ath_getbuf_locked() to take the above enum. * Right now anything sent via ic_raw_xmit() allocates via ATH_BUFTYPE_MGMT. This may not be very useful. * Add ATH_BUF_MGMT flag (ath_buf.bf_flags) which indicates the current buffer is a mgmt buffer and should go back onto the mgmt free list. * Extend 'txagg' to include debugging output for both normal and mgmt txbufs. * When checking/clearing ATH_BUF_BUSY, do it on both TX pools. Tested: * STA mode, with heavy UDP injection via iperf. This filled the TX queue however BARs were still going out successfully. TODO: * Initialise the mgmt buffers with ATH_BUF_MGMT and then ensure the right type is being allocated and freed on the appropriate list. That'd save a write operation (to bf->bf_flags) on each buffer alloc/free. * Test on AP mode, ensure that BAR TX and probe responses go out nicely when the main TX queue is filled (eg with paused traffic to a TID, awaiting a BAR to complete.) PR: kern/168170
2012-06-13 06:57:55 +00:00
extern struct ath_buf * ath_getbuf(struct ath_softc *sc,
ath_buf_type_t btype);
extern struct ath_buf * _ath_getbuf_locked(struct ath_softc *sc,
ath_buf_type_t btype);
Change ath_buf allocation to: * Immediately return NULL if a buffer isn't available; * Track the "buffers not available" count; * Clear some fields used for tx aggregation; * Add ath_buf_clone() which clones the majority of buffer state. This is needed when retransmission of a "busy" buffer is required. Sponsored by: Hobnob, Inc.
2011-11-08 21:13:05 +00:00
extern struct ath_buf * ath_buf_clone(struct ath_softc *sc,
const struct ath_buf *bf);
Implement a separate, smaller pool of ath_buf entries for use by management traffic. * Create sc_mgmt_txbuf and sc_mgmt_txdesc, initialise/free them appropriately. * Create an enum to represent buffer types in the API. * Extend ath_getbuf() and _ath_getbuf_locked() to take the above enum. * Right now anything sent via ic_raw_xmit() allocates via ATH_BUFTYPE_MGMT. This may not be very useful. * Add ATH_BUF_MGMT flag (ath_buf.bf_flags) which indicates the current buffer is a mgmt buffer and should go back onto the mgmt free list. * Extend 'txagg' to include debugging output for both normal and mgmt txbufs. * When checking/clearing ATH_BUF_BUSY, do it on both TX pools. Tested: * STA mode, with heavy UDP injection via iperf. This filled the TX queue however BARs were still going out successfully. TODO: * Initialise the mgmt buffers with ATH_BUF_MGMT and then ensure the right type is being allocated and freed on the appropriate list. That'd save a write operation (to bf->bf_flags) on each buffer alloc/free. * Test on AP mode, ensure that BAR TX and probe responses go out nicely when the main TX queue is filled (eg with paused traffic to a TID, awaiting a BAR to complete.) PR: kern/168170
2012-06-13 06:57:55 +00:00
/* XXX change this to NULL the buffer pointer? */
Refactor out the TX buffer management and completion code in preparation for TX aggregation. * Add in logic which calls ath_buf bf->bf_comp if it's set. This allows for AMPDU (and RIFS, and FF, if someone desires) code to handle completion - which includes freeing subframes, retransmitting subframes, etc. * Break out the buffer free, buffer busy/unbusy default completion handler code into separate functions. This allows bf_comp methods to free and unbusy each subframe ath_buf as required. * Break out the statistics update code into a separate function, just to clean up the TX completion path a little. Sponsored by: Hobnob, Inc.
2011-11-08 21:49:33 +00:00
extern void ath_freebuf(struct ath_softc *sc, struct ath_buf *bf);
Replace the direct sc_txbuf manipulation with a pair of functions. This is preparation work for having a separate ath_buf queue for management traffic. PR: kern/168170
2012-06-13 05:39:16 +00:00
extern void ath_returnbuf_head(struct ath_softc *sc, struct ath_buf *bf);
extern void ath_returnbuf_tail(struct ath_softc *sc, struct ath_buf *bf);
Migrate the TX path code out of if_ath and into a separate source file. There's two reasons for this: * the raw and non-raw TX path shares a lot of duplicate code which should be refactored; * the 11n-ready chip TX path needs a little reworking.
2011-01-29 11:35:23 +00:00
In preparation for supporting 11n TX/RX properly, allow for TX queue draining and interface resets to be marked as ATH_RESET_DEFAULT, ATH_RESET_FULL, ATH_RESET_NOLOSS. Currently a reset is still a reset - ie, all tx/rx frames in the hardware queues are purged. This means that those frames will be lost to the 11n TX and RX aggregation state tracking, breaking AMPDU sessions. The (eventual) new semantics: * ATH_RESET_DEFAULT: full reset, this is the default for reset situations which I haven't yet figured out what they should be. * ATH_RESET_FULL: A full reset - for things such as channel changes. * ATH_RESET_NOLOSS: Don't flush TX/RX queues - handle pending RX frames and leave TX frames where they are; restart TX DMA from where it was.
2011-11-08 18:56:52 +00:00
extern int ath_reset(struct ifnet *, ATH_RESET_TYPE);
Refactor out the TX buffer management and completion code in preparation for TX aggregation. * Add in logic which calls ath_buf bf->bf_comp if it's set. This allows for AMPDU (and RIFS, and FF, if someone desires) code to handle completion - which includes freeing subframes, retransmitting subframes, etc. * Break out the buffer free, buffer busy/unbusy default completion handler code into separate functions. This allows bf_comp methods to free and unbusy each subframe ath_buf as required. * Break out the statistics update code into a separate function, just to clean up the TX completion path a little. Sponsored by: Hobnob, Inc.
2011-11-08 21:49:33 +00:00
extern void ath_tx_draintxq(struct ath_softc *sc, struct ath_txq *txq);
extern void ath_tx_default_comp(struct ath_softc *sc, struct ath_buf *bf,
int fail);
Introduce TX aggregation and software TX queue management for Atheros AR5416 and later wireless devices. This is a very large commit - the complete history can be found in the user/adrian/if_ath_tx branch. Legacy (ie, pre-AR5416) devices also use the per-software TXQ support and (in theory) can support non-aggregation ADDBA sessions. However, the net80211 stack doesn't currently support this. In summary: TX path: * queued frames normally go onto a per-TID, per-node queue * some special frames (eg ADDBA control frames) are thrown directly onto the relevant hardware queue so they can go out before any software queued frames are queued. * Add methods to create, suspend, resume and tear down an aggregation session. * Add in software retransmission of both normal and aggregate frames. * Add in completion handling of aggregate frames, including parsing the block ack bitmap provided by the hardware. * Write an aggregation function which can assemble frames into an aggregate based on the selected rate control and channel configuration. * The per-TID queues are locked based on their target hardware TX queue. This matches what ath9k/atheros does, and thus simplified porting over some of the aggregation logic. * When doing TX aggregation, stick the sequence number allocation in the TX path rather than net80211 TX path, and protect it by the TXQ lock. Rate control: * Delay rate control selection until the frame is about to be queued to the hardware, so retried frames can have their rate control choices changed. Frames with a static rate control selection have that applied before each TX, just to simplify the TX path (ie, not have "static" and "dynamic" rate control special cased.) * Teach ath_rate_sample about aggregates - both completion and errors. * Add an EWMA for tracking what the current "good" MCS rate is based on failure rates. Misc: * Introduce a bunch of dirty hacks and workarounds so TID mapping and net80211 frame inspection can be kept out of the net80211 layer. Because of the way this code works (and it's from Atheros and Linux ath9k), there is a consistent, 1:1 mapping between TID and AC. So we need to ensure that frames going to a specific TID will _always_ end up on the right AC, and vice versa, or the completion/locking will simply get very confused. I plan on addressing this mess in the future. Known issues: * There is no BAR frame transmission just yet. A whole lot of tidying up needs to occur before BAR frame TX can occur in the "correct" place - ie, once the TID TX queue has been drained. * Interface reset/purge/etc results in frames in the TX and RX queues being removed. This creates holes in the sequence numbers being assigned and the TX/RX AMPDU code (on either side) just hangs. * There's no filtered frame support at the present moment, so stations going into power saving mode will simply have a number of frames dropped - likely resulting in a traffic "hang". * Raw frame TX is going to just not function with 11n aggregation. Likely this needs to be modified to always override the sequence number if the frame is going into an aggregation session. However, general raw frame injection currently doesn't work in general in net80211, so let's just ignore this for now until this is sorted out. * HT protection is just not implemented and won't be until the above is sorted out. In addition, the AR5416 has issues RTS protecting large aggregates (anything >8k), so the work around needs to be ported and tested. Thus, this will be put on hold until the above work is complete. * The rate control module 'sample' is the only currently supported module; onoe/amrr haven't been tested and have likely bit rotted a little. I'll follow up with some commits to make them work again for non-11n rates, but they won't be updated to handle 11n and aggregation. If someone wishes to do so then they're welcome to send along patches. * .. and "sample" doesn't really do a good job of 11n TX. Specifically, the metrics used (packet TX time and failure/success rates) isn't as useful for 11n. It's likely that it should be extended to take into account the aggregate throughput possible and then choose a rate which maximises that. Ie, it may be acceptable for a higher MCS rate with a higher failure to be used if it gives a more acceptable throughput/latency then a lower MCS rate @ a lower error rate. Again, patches will be gratefully accepted. Because of this, ATH_ENABLE_11N is still not enabled by default. Sponsored by: Hobnob, Inc. Obtained from: Linux, Atheros
2011-11-08 22:43:13 +00:00
extern void ath_tx_update_ratectrl(struct ath_softc *sc,
struct ieee80211_node *ni, struct ath_rc_series *rc,
struct ath_tx_status *ts, int frmlen, int nframes, int nbad);
Refactor out the TX buffer management and completion code in preparation for TX aggregation. * Add in logic which calls ath_buf bf->bf_comp if it's set. This allows for AMPDU (and RIFS, and FF, if someone desires) code to handle completion - which includes freeing subframes, retransmitting subframes, etc. * Break out the buffer free, buffer busy/unbusy default completion handler code into separate functions. This allows bf_comp methods to free and unbusy each subframe ath_buf as required. * Break out the statistics update code into a separate function, just to clean up the TX completion path a little. Sponsored by: Hobnob, Inc.
2011-11-08 21:49:33 +00:00
extern void ath_tx_freebuf(struct ath_softc *sc, struct ath_buf *bf,
int status);
Migrate the sysctl related routines (statistics, debugging, etc) out of if_ath.c and into if_ath_sysctl.c .
2011-03-02 16:03:19 +00:00
Migrate most of the beacon handling functions out to if_ath_beacon.c. This is also in preparation for supporting AR9300 and later NICs.
2012-05-20 04:14:29 +00:00
extern void ath_txqmove(struct ath_txq *dst, struct ath_txq *src);
Migrate the bulk of the RX routines out from if_ath.c to if_ath_rx.[ch]. * migrate the rx processing out into if_ath_rx.c * migrate the TSF functions into if_ath_tsf.h, as inlines This is in prepration for supporting the EDMA RX routines, required to support the AR93xx series NICs. TODO: * ath_start() shouldn't be private, but it's called as part of the RX path. I should likely migrate ath_rx_tasklet() back into if_ath.c and then return this to be 'static'. The RX code really shouldn't need to see TX routines (and vice versa.) * ath_beacon_* should be in if_ath_beacon.[ch]. * ath_tdma_* should be in if_ath_tdma.[ch] ...
2012-05-20 02:05:10 +00:00
extern void ath_mode_init(struct ath_softc *sc);
extern void ath_setdefantenna(struct ath_softc *sc, u_int antenna);
Migrate most of the beacon handling functions out to if_ath_beacon.c. This is also in preparation for supporting AR9300 and later NICs.
2012-05-20 04:14:29 +00:00
extern void ath_setslottime(struct ath_softc *sc);
Refactor out the descriptor allocation code from the buffer allocation code. The TX EDMA completion path is going to need descriptors allocated but not any buffers. This code will form the basis for that.
2012-07-27 05:34:45 +00:00
extern int ath_descdma_alloc_desc(struct ath_softc *sc,
struct ath_descdma *dd, ath_bufhead *head, const char *name,
int ds_size, int nbuf, int ndesc);
Further preparations for the RX EDMA support. Break out the DMA descriptor setup/teardown code into a method. The EDMA RX code doesn't allocate descriptors, just ath_buf entries.
2012-07-09 08:37:59 +00:00
extern int ath_descdma_setup(struct ath_softc *sc, struct ath_descdma *dd,
Modify ath_descdma_setup() to take a descriptor size parameter. The AR9300 and later descriptors are 128 bytes, however I'd like to make sure that isn't used for earlier chips. * Populate the TX descriptor length field in the softc with sizeof(ath_desc) * Use this field when allocating the TX descriptors * Pre-AR93xx TX/RX descriptors will use the ath_desc size; newer ones will query the HAL for these sizes.
2012-07-23 23:40:13 +00:00
ath_bufhead *head, const char *name, int ds_size, int nbuf,
int ndesc);
Fix EDMA RX to actually work without panicing the machine. I was setting up the RX EDMA buffer to be 4096 bytes rather than the RX data buffer portion. The hardware was likely getting very confused and DMAing descriptor portions into places it shouldn't, leading to memory corruption and occasional panics. Whilst here, don't bother allocating descriptors for the RX EDMA case. We don't use those descriptors. Instead, just allocate ath_buf entries.
2012-07-14 02:07:51 +00:00
extern int ath_descdma_setup_rx_edma(struct ath_softc *sc,
struct ath_descdma *dd, ath_bufhead *head, const char *name,
int nbuf, int desclen);
Further preparations for the RX EDMA support. Break out the DMA descriptor setup/teardown code into a method. The EDMA RX code doesn't allocate descriptors, just ath_buf entries.
2012-07-09 08:37:59 +00:00
extern void ath_descdma_cleanup(struct ath_softc *sc,
struct ath_descdma *dd, ath_bufhead *head);
Migrate the bulk of the RX routines out from if_ath.c to if_ath_rx.[ch]. * migrate the rx processing out into if_ath_rx.c * migrate the TSF functions into if_ath_tsf.h, as inlines This is in prepration for supporting the EDMA RX routines, required to support the AR93xx series NICs. TODO: * ath_start() shouldn't be private, but it's called as part of the RX path. I should likely migrate ath_rx_tasklet() back into if_ath.c and then return this to be 'static'. The RX code really shouldn't need to see TX routines (and vice versa.) * ath_beacon_* should be in if_ath_beacon.[ch]. * ath_tdma_* should be in if_ath_tdma.[ch] ...
2012-05-20 02:05:10 +00:00
/*
* This is only here so that the RX proc function can call it.
* It's very likely that the "start TX after RX" call should be
* done via something in if_ath.c, moving "rx tasklet" into
* if_ath.c and do the ath_start() call there. Once that's done,
* we can kill this.
*/
extern void ath_start(struct ifnet *ifp);
Create a function - ath_tx_kick() - which is called where ath_start() is called to "kick" along TX. For now, schedule a taskqueue call. Later on I may go back to the direct call of ath_rx_tasklet() - but for now, this will do. I've tested UDP and TCP TX. UDP TX still achieves 240MBit, but TCP TX gets stuck at around 100MBit or so, instead of the 150MBit it should be at. I'll re-test with no ACPI/power/sleep states enabled at startup and see what effect it has. This is in preparation for supporting an if_transmit() path, which will turn ath_tx_kick() into a NUL operation (as there won't be an ifnet queue to service.) Tested: * AR9280 STA TODO: * test on AR5416, AR9160, AR928x STA/AP modes PR: kern/168649
2012-06-05 03:14:49 +00:00
static inline void
ath_tx_kick(struct ath_softc *sc)
{
Mostly revert previous commit(s). After doing a bunch of local testing, it turns out that it negatively affects performance. I'm stil investigating exactly why deferring the IO causes such negative TCP performance but doesn't affect UDP preformance. Leave the ath_tx_kick() change in there however; it's going to be useful to have that there for if_transmit() work. PR: kern/168649
2012-06-05 06:03:55 +00:00
ath_start(sc->sc_ifp);
Create a function - ath_tx_kick() - which is called where ath_start() is called to "kick" along TX. For now, schedule a taskqueue call. Later on I may go back to the direct call of ath_rx_tasklet() - but for now, this will do. I've tested UDP and TCP TX. UDP TX still achieves 240MBit, but TCP TX gets stuck at around 100MBit or so, instead of the 150MBit it should be at. I'll re-test with no ACPI/power/sleep states enabled at startup and see what effect it has. This is in preparation for supporting an if_transmit() path, which will turn ath_tx_kick() into a NUL operation (as there won't be an ifnet queue to service.) Tested: * AR9280 STA TODO: * test on AR5416, AR9160, AR928x STA/AP modes PR: kern/168649
2012-06-05 03:14:49 +00:00
}
Migrate most of the beacon handling functions out to if_ath_beacon.c. This is also in preparation for supporting AR9300 and later NICs.
2012-05-20 04:14:29 +00:00
Migrate the TX path code out of if_ath and into a separate source file. There's two reasons for this: * the raw and non-raw TX path shares a lot of duplicate code which should be refactored; * the 11n-ready chip TX path needs a little reworking.
2011-01-29 11:35:23 +00:00
#endif
Reference in New Issue Copy Permalink