freebsd-nq/sys/dev/ata/atapi-all.h

197 lines
9.1 KiB
C
Raw Normal View History

Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/*-
* Copyright (c) 1998 - 2003 S<EFBFBD>ren Schmidt <sos@FreeBSD.org>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
1999-08-28 01:08:13 +00:00
* $FreeBSD$
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
*/
/* ATAPI misc defines */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_MAGIC_LSB 0x14
#define ATAPI_MAGIC_MSB 0xeb
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#define ATAPI_P_READ (ATA_S_DRQ | ATA_I_IN)
#define ATAPI_P_WRITE (ATA_S_DRQ)
#define ATAPI_P_CMDOUT (ATA_S_DRQ | ATA_I_CMD)
#define ATAPI_P_DONEDRQ (ATA_S_DRQ | ATA_I_CMD | ATA_I_IN)
#define ATAPI_P_DONE (ATA_I_CMD | ATA_I_IN)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#define ATAPI_P_ABORT 0
/* error register bits */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_E_MASK 0x0f /* error mask */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#define ATAPI_E_ILI 0x01 /* illegal length indication */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_E_EOM 0x02 /* end of media detected */
#define ATAPI_E_ABRT 0x04 /* command aborted */
#define ATAPI_E_MCR 0x08 /* media change requested */
#define ATAPI_SK_MASK 0xf0 /* sense key mask */
#define ATAPI_SK_NO_SENSE 0x00 /* no specific sense key info */
#define ATAPI_SK_RECOVERED_ERROR 0x10 /* command OK, data recovered */
#define ATAPI_SK_NOT_READY 0x20 /* no access to drive */
#define ATAPI_SK_MEDIUM_ERROR 0x30 /* non-recovered data error */
#define ATAPI_SK_HARDWARE_ERROR 0x40 /* non-recoverable HW failure */
#define ATAPI_SK_ILLEGAL_REQUEST 0x50 /* invalid command param(s) */
#define ATAPI_SK_UNIT_ATTENTION 0x60 /* media changed */
#define ATAPI_SK_DATA_PROTECT 0x70 /* write protect */
#define ATAPI_SK_BLANK_CHECK 0x80 /* blank check */
#define ATAPI_SK_VENDOR_SPECIFIC 0x90 /* vendor specific skey */
#define ATAPI_SK_COPY_ABORTED 0xa0 /* copy aborted */
#define ATAPI_SK_ABORTED_COMMAND 0xb0 /* command aborted, try again */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#define ATAPI_SK_EQUAL 0xc0 /* equal */
#define ATAPI_SK_VOLUME_OVERFLOW 0xd0 /* volume overflow */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_SK_MISCOMPARE 0xe0 /* data dont match the medium */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#define ATAPI_SK_RESERVED 0xf0
/* ATAPI commands */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_TEST_UNIT_READY 0x00 /* check if device is ready */
#define ATAPI_REZERO 0x01 /* rewind */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_REQUEST_SENSE 0x03 /* get sense data */
#define ATAPI_FORMAT 0x04 /* format unit */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_READ 0x08 /* read data */
#define ATAPI_WRITE 0x0a /* write data */
#define ATAPI_WEOF 0x10 /* write filemark */
#define WF_WRITE 0x01
#define ATAPI_SPACE 0x11 /* space command */
#define SP_FM 0x01
#define SP_EOD 0x03
#define ATAPI_MODE_SELECT 0x15 /* mode select */
#define ATAPI_ERASE 0x19 /* erase */
#define ATAPI_MODE_SENSE 0x1a /* mode sense */
#define ATAPI_START_STOP 0x1b /* start/stop unit */
#define SS_LOAD 0x01
#define SS_RETENSION 0x02
#define SS_EJECT 0x04
#define ATAPI_PREVENT_ALLOW 0x1e /* media removal */
#define ATAPI_READ_FORMAT_CAPACITIES 0x23 /* get format capacities */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_READ_CAPACITY 0x25 /* get volume capacity */
#define ATAPI_READ_BIG 0x28 /* read data */
#define ATAPI_WRITE_BIG 0x2a /* write data */
#define ATAPI_LOCATE 0x2b /* locate to position */
#define ATAPI_READ_POSITION 0x34 /* read position */
#define ATAPI_SYNCHRONIZE_CACHE 0x35 /* flush buf, close channel */
#define ATAPI_WRITE_BUFFER 0x3b /* write device buffer */
#define ATAPI_READ_BUFFER 0x3c /* read device buffer */
#define ATAPI_READ_SUBCHANNEL 0x42 /* get subchannel info */
#define ATAPI_READ_TOC 0x43 /* get table of contents */
#define ATAPI_PLAY_10 0x45 /* play by lba */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_PLAY_MSF 0x47 /* play by MSF address */
#define ATAPI_PLAY_TRACK 0x48 /* play by track number */
#define ATAPI_PAUSE 0x4b /* pause audio operation */
#define ATAPI_READ_DISK_INFO 0x51 /* get disk info structure */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_READ_TRACK_INFO 0x52 /* get track info structure */
#define ATAPI_RESERVE_TRACK 0x53 /* reserve track */
#define ATAPI_SEND_OPC_INFO 0x54 /* send OPC structurek */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_MODE_SELECT_BIG 0x55 /* set device parameters */
#define ATAPI_REPAIR_TRACK 0x58 /* repair track */
#define ATAPI_READ_MASTER_CUE 0x59 /* read master CUE info */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_MODE_SENSE_BIG 0x5a /* get device parameters */
#define ATAPI_CLOSE_TRACK 0x5b /* close track/session */
#define ATAPI_READ_BUFFER_CAPACITY 0x5c /* get buffer capicity */
#define ATAPI_SEND_CUE_SHEET 0x5d /* send CUE sheet */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_BLANK 0xa1 /* blank the media */
#define ATAPI_SEND_KEY 0xa3 /* send DVD key structure */
#define ATAPI_REPORT_KEY 0xa4 /* get DVD key structure */
#define ATAPI_PLAY_12 0xa5 /* play by lba */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_LOAD_UNLOAD 0xa6 /* changer control command */
#define ATAPI_READ_STRUCTURE 0xad /* get DVD structure */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_PLAY_CD 0xb4 /* universal play command */
#define ATAPI_SET_SPEED 0xbb /* set drive speed */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
#define ATAPI_MECH_STATUS 0xbd /* get changer status */
#define ATAPI_READ_CD 0xbe /* read data */
#define ATAPI_POLL_DSC 0xff /* poll DSC status bit */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
/* ATAPI request sense structure */
struct atapi_reqsense {
u_int8_t error_code :7; /* current or deferred errors */
u_int8_t valid :1; /* follows ATAPI spec */
u_int8_t segment; /* Segment number */
u_int8_t sense_key :4; /* sense key */
u_int8_t reserved2_4 :1; /* reserved */
u_int8_t ili :1; /* incorrect length indicator */
u_int8_t eom :1; /* end of medium */
u_int8_t filemark :1; /* filemark */
/* cmd information */
2002-09-23 18:54:32 +00:00
u_int32_t cmd_info __packed;
u_int8_t sense_length; /* additional sense len (n-7) */
/* additional cmd spec info */
2002-09-23 18:54:32 +00:00
u_int32_t cmd_specific_info __packed;
u_int8_t asc; /* additional sense code */
u_int8_t ascq; /* additional sense code qual */
u_int8_t replaceable_unit_code; /* replaceable unit code */
u_int8_t sk_specific :7; /* sense key specific */
u_int8_t sksv :1; /* sense key specific info OK */
u_int8_t sk_specific1; /* sense key specific */
u_int8_t sk_specific2; /* sense key specific */
};
typedef int atapi_callback_t(struct atapi_request *);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
struct atapi_request {
struct ata_device *device; /* ptr to parent softc */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
u_int8_t ccb[16]; /* command control block */
int ccbsize; /* size of ccb (12 | 16) */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
u_int32_t bytecount; /* bytes to transfer */
u_int32_t donecount; /* bytes transferred */
int timeout; /* timeout for this cmd */
Ten'th update to the new ATA/ATAPI driver: It been awhile since the last major update, as a benefit there are some cool things in this one (and new bugs probably :) )... The ATA driver has grown "real" timeout support for all devices. This means that it should be possible to get in contact with (especially) lost ATAPI devices. It also means that the ATA driver is now usable on notebooks as it will DTRT on resume. An experimental hack at utilizing the Promise66's at UDMA66 is in there, but I cant test it. If someone feels like sending me one, give me a ping. The ATAPI DMA enableling scheme has been changed, also better DMA support for the Aladdin chipset has been implemented for ATAPI devices. Note that the Aladdin apparently only can do DMA reads on ATAPI devices, and the Promise cant do ATAPI DMA at all. I have seen problems on some ATAPI devices that should be able to run in DMA mode, so if you encounter problems with hanging atapi devices during the probe, or during access, disable DMA in atapi-all.c, and let me know. It might be nessesary to do this via a "white list" for known good devices... The ATAPI CDROM driver can now use eject/close without hanging and the bug that caused reading beyond the end of a CD has been fixed. Media change is also handled proberly. DVD drives are identified and are usable as CDROM devices at least, I dont have the HW to test this further, see above :). The ATAPI tape driver has gotten some support for using the DSC method for not blocking the IDE channel during read/write when the device has full buffers. It knows about the OnStream DI-30 device, support is not completed yet, but it can function as a primitive backup medium, without filemarks, and without bad media handeling. This is because the OnStream device doesn't handle this (like everybody else) in HW. It also now supports getting/setting the record position on devices that supports it. Some rather major cleanups and rearrangements as well (cvs -b diff is your freind). I'm closing in on declaring this for beta code, most of the infrastruture is in place by now. As usual USE AT YOUR OWN RISK!!, this is still alpha level code. This driver can hose your disk real bad if anything goes wrong, but now you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-09-21 19:50:40 +00:00
struct callout_handle timeout_handle; /* handle for untimeout */
int retries; /* retry count */
int result; /* result of this cmd */
int error; /* result translated to errno */
struct atapi_reqsense sense; /* sense data if error */
int flags;
#define ATPR_F_READ 0x0001
#define ATPR_F_DMA_USED 0x0002
#define ATPR_F_AT_HEAD 0x0004
#define ATPR_F_INTERNAL 0x0008
#define ATPR_F_QUIET 0x0010
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
caddr_t data; /* pointer to data buf */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
atapi_callback_t *callback; /* ptr to callback func */
void *driver; /* driver specific */
TAILQ_ENTRY(atapi_request) chain; /* list management */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
};
void atapi_attach(struct ata_device *);
void atapi_cam_attach_bus(struct ata_channel *);
void atapi_detach(struct ata_device *);
void atapi_cam_detach_bus(struct ata_channel *);
void atapi_cam_reinit_bus(struct ata_channel *);
void atapi_reinit(struct ata_device *);
void atapi_start(struct ata_device *);
int atapi_transfer(struct atapi_request *);
int atapi_interrupt(struct atapi_request *);
int atapi_queue_cmd(struct ata_device *, int8_t [], caddr_t, int, int, int, atapi_callback_t, void *);
int atapi_test_ready(struct ata_device *);
int atapi_wait_dsc(struct ata_device *, int);
void atapi_request_sense(struct ata_device *, struct atapi_reqsense *);
void atapi_dump(char *, void *, int);
int acdattach(struct ata_device *);
void acddetach(struct ata_device *);
void acd_start(struct ata_device *);
int afdattach(struct ata_device *);
void afddetach(struct ata_device *);
void afd_start(struct ata_device *);
int astattach(struct ata_device *);
void astdetach(struct ata_device *);
void ast_start(struct ata_device *);