blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
a KLD. Still doesn't work well except in the PCMCIA case (now if only
pccardd(8) could load and unload drivers dynamically...). Mainly, it
tries to find fdc0 on the PCI bus for whatever obscure reasons, but i
need someone who understands driver(9) to fix this. However, it's at least
already better than before, and i'm tired of maintaining too many private
changes in my tree, given the large patches bde submitted. :)
Idea of a KLD triggered by: Michael Reifenberger <root@nihil.plaut.de>
could only get a chance of testing it under 4.3, but together with the
if_oltr.c fixes at least it seems to work now. If someone has the chance
to test this under -current, please do.
Unfortunaltey, the TR code itself (if_iso88025subr.c) is not written
in a way that would allow to make a seaparate KLD out of it. By now,
just link it directly into the oltr KLD since it's probably the POLA
to be able to load the TR code together with the only TR hardware
driver we've got by now.
I've got one single unexplained panic (in doreti_switch or somewhere
there, calling a 0xc1XXXXXX address that did no longer belong to the
kernel at all) after unloading the modules once, thus i don't propose
a MFC of this module despite my testing has been done solely on 4.3,
unless someone is really going to test this stuff in -current.
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
systems were repo-copied from sys/miscfs to sys/fs.
- Renamed the following file systems and their modules:
fdesc -> fdescfs, portal -> portalfs, union -> unionfs.
- Renamed corresponding kernel options:
FDESC -> FDESCFS, PORTAL -> PORTALFS, UNION -> UNIONFS.
- Install header files for the above file systems.
- Removed bogus -I${.CURDIR}/../../sys CFLAGS from userland
Makefiles.
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
the video switch by another. Exactly as VESA does on top of VGA.
It adds linear framebuffer to S3 VESA 1.2 cards.
Obtained from: The original S3 ISA code comes from
Peter Horton <pdh@colonel-panic.com>
Add detach routine and turn driver into a module so it can be loaded
and unloaded. Also take a stab at implementing multicast packet
reception so that this NIC will work with IPv6. Promiscuous mode
doesn't seem to work, but I'm not sure why. It works well enough that
I can run dhclient on it and put it on the office network though.
Also ripped out spl stuff and replaced it with mutexes.
