by default. As such, mark if_dc as IFF_NEEDSGIANT until such
time as appropriate locking review and testing can take place,
and the locking can be enabled by default.
RELENG_5 candidate.
Set the DMA SGL length correctly if the DMA request must be chained because
it is too large to fit in one SGL.
This should fix this driver for some Dell Precision systems.
RELENG_5 candidate.
PR: kern/66479
Submitted by: HITOSHI Osada <qfh02545@nifty.com>
the geometry code to grab a mutex that prohibits any driver on the
stack below it from sleeping, it's not safe to allow anything in
the top half of isp to sleep (excepting the thread that Fibre Channel
instances use to re-scan loops/fabrics).
hold its own values, pass them up to the parent (acpi0) and merge/uniq them
on the way. After the namespace evaluation, acpi will reserve these
resources and manage them via rman before bus_generic_probe() and
bus_generic_attach(). This is necessary because some systems specify
conflicting resources in separate sysresource objects. It's also cleaner
in that the interface between sysresource and acpi is now merely the parent's
resource list. This code handles the following cases:
1. Unique resource: add it to the parent via bus_set_resource().
2. New wholly contained in old: discard new.
3. New tail overlaps old head: grow old head downward.
AND/OR
4. New head overlaps old tail: grow old tail upward.
Tested by: Pawel Worach <sajd_at_telia.com>
Tested by: Radek Kozlowski <radek_at_raadradd.com>
MFC after: 5 days
deal with 24-bit addresses. While the two other attachments, namely
isa and cbus, do it properly, the PCI attachment was passing
BUS_SPACE_MAXADDR instead of BUS_SPACE_MAXADDR_24BIT. This bug
became apparent with the new contigmalloc() code.
This fixes the problem reported with lnc(4) interfaces inside VMWare,
and should theoritically also fix any user of a PCI lnc(4) card. It
is a RELENG_5 MFC candidate.
Tested by: Florian Le Goff <madflo@beertech.org>
before returning. Device nodes are created via the "taste" mechanism,
so this is necessary in order to make sure that devfs entries are
created before mdconfig(8) returns.
This may be a MFC candidate for 5.3.
Suggested by: phk
allocation. Notably, in this case, the driver tries to allocate several
pieces of memory and then fails if the pieces allocated after the first
do not come after it physically, and within a specific range (8MB I
believe). Of course, this could just as easily fail for any number of
reasons, but it almost always fails now that contiguous allocations start
at the end of possible specified memory locations rather than the beginning.
Allocate all the possibly-needed memory up front, even though it's a waste,
to get around this. The least bogus solution would be to take the physical
address from the first allocation and create a new tag that specified that
further allocations must follow it within that 8MB window, then use that
when allocating new channels, but that's left for anyone else that really
feels like doing it.
Tested by: Erwin Lansing <erwin@lansing.dk>
to check aperture size, avoiding hangs. Maintain the rest of the bits when
setting/unsetting ATTBASE. This essentially matches Linux's AGP driver as well.
PR: kern/70037
Submitted by: Mark Tinguely <tinguely at casselton dot net>
Obtained from: NetBSD
systems that have overlapping regions specified in their sysresource
objects. This patch fixes ATA DMA and acpi_timer allocation for such
sysctems. It should eventually be moved to resource_list_add() if it is
a valid generalized approach. The minimal approach for 5.3 is:
"Loop through all current resources to see if the new one overlaps
any existing ones. If so, the old one always takes precedence and
the new one is adjusted (or rejected). We check for three cases:
1. Tail of new resource overlaps head of old resource: truncate the
new resource so it is contiguous with the start of the old.
2. New resource wholly contained within the old resource: error.
3. Head of new resource overlaps tail of old resource: truncate the
new resource so it is contiguous, following the old."
Tested by: Radek Kozlowski <radek_at_raadradd.com>
Discussed with: imp
MFC after: 4 days
of 0x3f2-0x3f5,0x3f7 the ports are not 7 bytes apart. This should fix
floppy probing on such systems. (We handle the case of adjusting for
a start of 0x3f2 -> 0x3f0 separately, although that code should still be
checked if there are still floppy problems for others.)
Tested by: Sarunas Vancevicius <vsarunas_at_eircom.net>
MFC after: 3 days
Centralize the fdctl_wr() function by adding the offset in
the resource to the softc structure.
Bugfix: Read the drive-change signal from the correct place:
same place as the ctl register.
Remove the cdevsw{} related code and implement a GEOM class.
Ditch the state-engine and park a thread on each controller
to service the queue.
Make the interrupt FAST & MPSAFE since it is just a simple
wakeup(9) call.
Rely on a per controller mutex to protect the bioqueues.
Grab GEOMs topology lock when we have to and Giant when
ISADMA needs it. Since all access to the hardware is
isolated in the per controller thread, the rest of the
driver is lock & Giant free.
Create a per-drive queue where requests are parked while
the motor spins up. When the motor is running the requests
are purged to the per controller queue. This allows
requests to other drives to be serviced during spin-up.
Only setup the motor-off timeout when we finish the last
request on the queue and cancel it when a new request
arrives. This fixes the bug in the old code where the motor
turned off while we were still retrying a request.
Make the "drive-change" work reliably. Probe the drive on
first opens. Probe with a recal and a seek to cyl=1 to
reset the drive change line and check again to see if we
have a media.
When we see the media disappear we destroy the geom provider,
create a new one, and flag that autodetection should happen
next time we see a media (unless a specific format is configured).
Add sysctl tunables for a lot of drive related parameters.
If you spend a lot of time waiting for floppies you can
grab the i82078 pdf from Intels web-page and try tuning
these.
Add sysctl debug.fdc.debugflags which will enable various
kinds of debugging printfs.
Add central definitions of our well known floppy formats.
Simplify datastructures for autoselection of format and
call the code at the right times.
Bugfix: Remove at least one piece of code which would have
made 2.88M floppies not work.
Use implied seeks on enhanced controllers.
Use multisector transfers on all controllers. Increase
ISADMA bounce buffers accordingly.
Fall back to single sector when retrying. Reset retry count
on every successful transaction.
Sort functions in a more sensible order and generally tidy
up a fair bit here and there.
Assorted related fixes and adjustments in userland utilities.
WORKAROUNDS:
Do allow r/w opens of r/o media but refuse actual write
operations. This is necessary until the p4::phk_bufwork
branch gets integrated (This problem relates to remounting
not reopening devices, see sys/*/*/${fs}_vfsops.c for details).
Keep PC98's private copy of the old floppy driver compiling
and presumably working (see below).
TODO (planned)
Move probing of drives until after interrupts/timeouts work
(like for ATA/SCSI drives).
TODO (unplanned)
This driver should be made to work on PC98 as well.
Test on YE-DATA PCMCIA floppy drive.
Fix 2.88M media.
This is a MT5 candidate (depends on the bioq_takefirst() addition).
the driver to issue a bus reset more quickly than intended. We want to
*wait* if we find another SCB that could be the cause of this timeout,
not proceed to a bus reset.
Noticed by: kan
callers. These ioctls attempted to enable and disable the ACPI
interpreter at runtime. In practice, it is not possible to boot with
ACPI and then disable it on many systems and trying to do so can cause
crashes, interrupt storms, etc. Binary compatibility with userland is
retained.
MFC after: 2 days
also generates a notify. Since we held the lock over this call, the
notify never got to run and the battery status read never returned.
Document this also.
Tested by: Maxim Maximov <mcsi_at_mcsi.pp.ru>
Approved by: re (scottl)
data packet is received from the mouse. In the case of many KVM's,
this avoids a bug in their mouse emulation that sends back incorrect
sync when you explicitly request a data packet from the mouse. Without
this change, you must force the driver into stock PS/2 mode or be flooded
with a never ending stream of "out of sync" messages on these KVMs.
Approved by: re
The ISA probe uses an identify routine to probe all slot locations from
1 to 14 that do not conflict with other allocated resources. This required
making aic7770.c part of the driver core when compiled as a module.
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
Use aic_scb_timer_start() consistently to start the watchdog timer.
This removes a few places that verbatum copied the code in
aic_scb_timer_start().
During recovery processing, allow commands to still be queued to
the controller. The only requirement we have is that our recovery
command be queued first - something the code already guaranteed.
The only other change required to make this work is to prevent
timers from being started for these newly queued commands.
Approved by: re
only required to support probing of the Adaptec 284X VLB SCSI controller
which becomes visible in EISA space if you perform these writes. 284X
probing is moving to an ISA attachment.
This was tested with a Netgear WG311v2 802.11b/g PCI card. Things
that were fixed:
- This chip has two memory mapped regions, one at PCIR_BAR(0) and the
other at PCIR_BAR(1). This is a little different from the other
chips I've seen with two PCI shared memory regions, since they tend
to have the second BAR ad PCIR_BAR(2). if_ndis_pci.c tests explicitly
for PCIR_BAR(2). This has been changed to simply fill in ndis_res_mem
first and ndis_res_altmem second, if a second shared memory range
exists. Given that NDIS drivers seem to scan for BARs in ascending
order, I think this should be ok.
- Fixed the code that tries to process firmware images that have been
loaded as .ko files. To save a step, I was setting up the address
mapping in ndis_open_file(), but ndis_map_file() flags pre-existing
mappings as an error (to avoid duplicate mappings). Changed this so
that the mapping is now donw in ndis_map_file() as expected.
- Made the typedef for 'driver_entry' explicitly include __stdcall
to silence gcc warning in ndis_load_driver().
NOTE: the Texas Instruments ACX111 driver needs firmware. With my
card, there were 3 .bin files shipped with the driver. You must
either put these files in /compat/ndis or convert them with
ndiscvt -f and kldload them so the driver can use them. Without
the firmware image, the NIC won't work.
prodstr may be NULL when fetched. For the default device description,
guard against this and return the numeric IDs instead when this
happens. For the matching routines, and consider NULL to not match
those entries that aren't NULL w/o calling strcmp.
Early patches by: Anders Hanssen
Without this, the device cannot detect the end of ethernet packets
whose size is a multiple of the USB packat size.
PR: kern/70474
Submitted by: Andrew Thompson <andy@fud.org.nz>
MFC after: 1 week
a more complete subsystem, and removes the knowlege of how things are
implemented from the drivers. Include locking around filter ops, so a
module like aio will know when not to be unloaded if there are outstanding
knotes using it's filter ops.
Currently, it uses the MTX_DUPOK even though it is not always safe to
aquire duplicate locks. Witness currently doesn't support the ability
to discover if a dup lock is ok (in some cases).
Reviewed by: green, rwatson (both earlier versions)
and that can be used as an identify function for all kinds of busses on a
certain platform. Expect for sparc64 these are only stubs right now. [1]
- For sparc64, add code to its uart_cpu_identify() for registering the on-
board ISA UARTs and their resources based on information obtained from
Open Firmware.
It would be better if this would be done in the OFW ISA code. However, due
to the common FreeBSD ISA code and PNP-IDs not always being present in the
properties of the ISA nodes there seems to be no good way to implement that.
Therefore special casing UARTs as the sole really relevant ISA devices on
sparc64 seemed reasonable. [2]
Approved by: marcel
Discussed with: marcel [1], tmm [2]
Tested by: make universe
without Open Firmware directly instead of using OF_getetheraddr(). This is
a bit painful though, as the MAC address is contained in the NA field of
the VPD of the EBus bridge, which is is another function of the same chip.
To make it worse, the VPD of the EBus bridge can't be accessed via the PCI
capability pointer but has to be digged out from the Boot PROM and has a
non-standard format.
The PCI VPD struct and macros used here should be part of the FreeBSD PCI
code nevertheless.
Approved by: tmm
Based on: NetBSD
Tested with: Sun X1032A (hme(4)-isp(4)-combo card) on alpha and i386
o reprobe children when a new driver is added to uhub
o fix the usbd_probe_and_attach to set the ivars to a malloc'd area, as well
as freeing the ivars on child destruction.
o Don't delete children that don't attach. Evidentally, the need to do this
is a common misconception.
o minor formatting foo that may violate style(9) at the moment, but keeps the
diffs against my p4 tree smaller.
This does not solve the ugen gobbling things up problem, but the fixes
I have for that expose bugs in other parts of the tree...
variable. If set to "true" OF_getetheraddr() will now return the unique
MAC address stored in the "local-mac-address" property of the device's
OFW node if present and the host address/system default MAC address if
the node doesn't doesn't have such a property. If set to "false" the
host address will be returned for all devices like before this change.
This brings the behaviour of device drivers for NICs with OFW support/
FCode, i.e. dc(4) for on-board DM9102A on Sun machines, gem(4) and hme(4),
regarding "local-mac-address?" in line with NetBSD and Solaris.
The man pages of the respective drivers will be updated separately to
reflect this change.
- Remove OF_getetheraddr2() which was used as a stopgap in dc(4). Its
functionality is now part of OF_getetheraddr().
the interface as IFF_NEEDSGIANT so if_start is run holding Giant.
Note: mutexes are initialized in the softc for this driver, but the
locking appears inadequate to allow Giant-free operation.
the interface as IFF_NEEDSGIANT so if_start is run holding Giant.
Note: this driver does declare and occasionally reference mutexes,
but I believe not nearly enough to provide safety.
code was adjusting twice for the instruction pointer indicating
the *next* instruction to execute. The aic79xx driver had a similar
bug, but was fixed some time ago.
* Serialize access to the sysctl routines and the notify handler
* Assert that the sx lock is held in any functions they call.
* Note that recursively calling to re-enable the hotkeys is sub-optimal.
* Remove the interrupt wrapper that locked Giant and call the handler
directly. Mark the handler as MPSAFE.
* Don't attempt to detect if a handler is installed. Leave that to the
bus_alloc_resource() function.
* Serialize operations in acpi_video_bind_outputs(), acpi_video_detach(),
acpi_video_notify_handler(), acpi_video_power_profile(), and the sysctls.
The main goal is to protect the shared device list and prevent conflicting
settings.
* Add assertions that the sx lock is held in the leaf functions.
* Restructure the event handling path. acpi_tz_thread() now calls
acpi_tz_timeout() any time an event occurs. acpi_tz_timeout() checks
the flags and calls acpi_tz_power_profile(), acpi_tz_establish(), and
acpi_tz_monitor() as appropriate. Notifies only do a wakeup and let
acpi_tz_thread() do the actual work. This path is cleaner and allows
locking since the call path is now always a D.A.G.
* Add the acpi_tz_signal() function to set flags and wake the thread.
* Remove the tz_tmp_updating flag since calls are serialized by
acpi_tz_thread().
* Remove Giant locking.
* Serialize acpi_pwr_switch_consumer() and acpi_pwr_wake_enable().
* Make acpi_pwr_switch_consumer() have a single exit point.
* Add assertions to the leaf functions they call.
* Fix a memory leak in acpi_pwr_deregister_consumer(). However, it is
currently ifdefed out so this code was unused.
* Serialize access to acpi_pci_link_config(), acpi_pci_find_prt(),
acpi_pci_link_route(), and acpi_pci_link_resume().
* Add lock assertions to all functions called by them.
* Serialize notifying the user in acpi_lid_notify_status_changed(). This
way multiple lid events occur in order.
* Add an initialization pass to get the lid status at boot-time. This
pass does not notify any apps but gets the initial status.
* Use the common serialization macros instead of rolling our own.
* Increase the coverage of the lock in EcSpaceHandler() to cover the entire
loop to avoid dropping the lock when reading more than one byte.
* Serialize ops in acpi_cmbat_notify_handler(), acpi_cmbat_ioctl(),
acpi_cmbat_init_battery(), and acpi_cmbat_get_battinfo().
* Get the softc directly in acpi_cmbat_get_total_battinfo() rather than
build an array of them.
* Don't queue a _BIF query after receiving a notify. Since we clear the
timespec, a _BIF query will be done in the context of the next caller.
* Add asserts to leaf functions that operate on shared data.
* Remove the bst/bif updating flags now that we hold the lock over the
full query.
* Explain various comments in more detail.
* Serialize acpi_battery_get_battdesc(), acpi_battery_register(), and
acpi_battery_remove().
* Assert that the sx lock is held in acpi_batteries_init().
* Remove check for device_get_softc() returning NULL.
* Serialize notification of acline changes in acpi_acad_get_status().
* Remove the initializing flag. With the locking, we don't need to
push off requests for the acline before initialization is done.
* Don't check device_get_softc(), it can't return NULL.
* Serialize calls to acpi_alloc_resource(), acpi_release_resource(),
acpi_Enable(), acpi_Disable(), and acpi_debug_sysctl().
* Acquire the ACPI mutex in acpi_register_ioctl(), acpi_deregister_ioctl(),
and acpiioctl().
* Acquire the mutex while disabling subsequent requests to enter a
sleep state in acpi_SetSleepState().
* Be sure to re-enable sleep requests and don't run resume methods when
the current request fails.
* Don't check if sleep requests are disabled in the ACPIIO_SETSLPSTATE
ioctl. acpi_SetSleepState() does this for us.
* Remove the acquisition of Giant from the struct cdevsw.
* Remove the ACPI_USE_THREADS option.
* Add and comment our locking primitives. The mutex primitives use a
a static mutex and the serialization ones use a static sx lock. A global
acpi_mutex is used for access to global resources (i.e., writes to the
SMI_CMD register.)
* Remove 4.x compat defines.
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
there is no irq link. Since we now use the stored copy of PRT, not the
one that used to be passed into acpi_pcib_route_interrupt(), we need it in
the list. [1]
Fix a bug in acpi_pci_find_prt() where we weren't checking the bus, thus
choosing the wrong PRT entry to use for routing the link. Also, add a
printf for the case where the PRT entry is not found as this should not
happen.
Tested by: marcel [1]
incomplete in that the PRT routing was not aware of link programming.
Fix this by doing all routing through the link devices. The new algorithm
for setting up links is:
1. Read _CRS to get current setting. If invalid (not in _PRS), then set
to 0.
2. Attempt to call _DIS on the link. If successful, mark the link as not
routed. Otherwise, assume it still is.
Then when a routing request occurs:
3. Update weights for all IRQs
4. Attempt to route the initial IRQ if valid
5. If that fails, walk through the sorted list, attempting to route IRQs.
6. Configure the trigger/polarity based on _PRS.
Other changes:
* Add acpi_pci_find_prt() to look up the PRT entry for a given device and
acpi_pci_link_route() to select/route the best IRQ for it.
* Remove duplicated code in acpi_pcib_route_interrupt() that picked the
first IRQ from _PRS.
* Remove unneeded arguments from acpi_pcib_resume() and friends.
* Ignore _STA on link devices but report if it seems strange.
* Add a prt_source handle to the PRT structure since the ACPI struct
ACPI_PCI_ROUTING_TABLE uses a fixed-size entry for it. We'll need to
dynamically size this object if we want to use it the same way ACPI-CA
does. Null-terminate the source.
Tested by: Luo Hong <luohong99_at_mails.tsinghua.edu.cn>,
Jeffrey Katcher <jmkatcher_at_yahoo.com>
Info from: jhb, Len Brown (Intel)
if_start routines cannot currently be entered without Giant. When
the kernel is running with debug.mpsafenet != 0, this will defer
if_start execution to a task queue thread holding Giant, which may
introduce additional latency, but avoid incorrect execution.
Suggested by: dfr
full, avoiding the cost of mutex operations if it is. We re-test
once the mutex is acquired to make sure it's still true before doing
the -modify-write part of the read-modify-write. Note that due to
the maximum fifo depth being pretty deep, this is unlikely to improve
harvesting performance yet.
Approved by: markm
chipsets, based on Linux's via-agp.c. On boot, the system selects which AGP
version to use based on the inserted card. If v2 was chosen, the chipset
needs to be programmed with the v2 registers still. Also included in kern/69953
are changes to make the programming of the v3 registers match linux, but that
will be left out until the need to do so is confirmed (want specs or a tester).
PR: kern/69953
Submitted by: Oleg Sharoiko <os@rsu.ru>
Tested by: Oleg Sharoiko <os@rsu.ru>, Geoff Speicher <geoff@speicher.org>
(full version from PR)
o Change the motion calculation to result in
a more reasonable speed of motion
This should fix the 'aiming' problems people have reported. It also
mitigates (but doesn't completely solve) the 'stalling' problems at
very low speeds.
Tested by: many subscribers to -current
Approved by: njl
o Catch 'taps' as button presses
o One finger sends button1, two fingers send button3,
three fingers send button2 (double-click)
Tested by: many subscribers to -current
Approved by: njl
o Handle the 'up/down' buttons some touchpads have as
a z-axis (scrollwheel) as recommended by the specs
o Report the buttons as button4 and button5 instead
of button2 and button4, button2 can be emulated by
pressing button1 and button3 simultaneously. This
allows one to use the two extra buttons for other
purposes if one so desires.
Tested by: many subscribers to -current
Approved by: njl
o Clean up whitespace and comments in the
enable_synaptics() probing function
o Only use (and rely on) the extended capability
bits when we are told they actually exist
o Partly ignore the (possibly dated?) part of the
specification about the mode byte so that we
can support 'guest devices' too.
Tested by: many subscribers to -current
Approved by: njl
was being unconditionally dereferenced but was NULL for PIO requests.
Check the request flags for a DMA transaction before dereferencing.
Reported by: ceri
Tested by: Radek Kozlowski <radek -at- raadradd.com>
with it that need to be understood better before they can be resolved.
This takes time and time is already in short supply.
Reported & tested by: glebius@
message if they are incorrect. Also, remove the hack of allowing the
initial irq setting to not be in _PRS. As before, the old behavior can be
regained by defining ACPI_OLD_PCI_LINK.
want a splash screen.
There seems to be some confusion in the syscons code as to the meaning of
the SC_KERNEL_CONSOLE flag. Its absence is sometimes interpreted to mean
"I am not the system console", and sometimes to mean "I am not the only
VGA console" (see the font loading code for an example of the latter).
Someone with better syscons fu than myself should take a closer look.
following behavior:
* Link devices return invalid status (_STA) values. The results are very
unreliable -- sometimes never present. Just ignore the status and pick
the best configuration from _PRS.
* Link devices return invalid current settings (_CRS). Even after setting
the link value, many systems still return a different setting for _CRS.
When setting an IRQ, don't bother to check _CRS to see if we succeeded.
Note that we still check _CRS before routing and this should be addressed
as well.
Since this is a sensitive area, leave the old behavior accessible via
uncommenting the define for ACPI_OLD_PCI_LINK at the top of the file. Once
this has been thoroughly tested, this option and the code it covers will
be removed.
Thanks to Len Brown at Intel for informing us of these issues as he worked
around them in Linux.
Since HME doesn't compensate the checksum for UDP datagram which
can yield to 0x0, UDP transmit checksum offload is disabled by
default. The UDP Transmit checksum offload can be reactivated
by setting special link option link0 with ifconfig(8).
Approved by: jake (mentor)
Reviewed by: tmm
Tested by: Herve Boulouis <amon@sockar.homeip.net>
by a transaction performing a driver handled message sequence (an
scb with the MK_MESSAGE flag set).
SCBs that perform host managed messaging must always be
at the head of their per-target selection queue so that
the firmware knows to manually assert ATN if the current
negotiation agreement is packetized. In the past we
guaranteed this by queuing these SCBs separarately in
the execution queue. This exposes the system to potential
command reordering in two cases:
1) Another SCB for the same ITL nexus is queued that does
not have the MK_MESSAGE flag set. This SCB will be
queued to the per-target list which can be serviced
before the MK_MESSAGE scb that preceeded it.
2) If the target cannot accept all of the commands in the
per-target selection queue in one selection, the remainder
is queued to the tail of the selection queues so as to
effect round-robin scheduling. This could allow the
MK_MESSAGE scb to be sent to the target before the
requeued commands.
This commit changes the firmware policy to defer queuing
MK_MESSAGE SCBs into the selection queues until this can
be done without affecting order. This means that the
target's selection queue is either empty, or the last
SCB on the execution queue is also a MK_MESSAGE SCB.
During any wait, the firmware halts the download of new
SCBs so only a single "holding location" is required.
Luckily, MK_MESSAGE SCBs are rare and typically occur only
during CAM's bus probe where only one command is outstanding
at a time. However, during some recovery scenarios, the
reordering *could* occur.
aic79xx.c:
Update ahd_search_qinfifo() and helper routines to
search for pending MK_MESSAGE scbs and properly
restitch the execution queue if either the MK_MESSAGE
SCB is being aborted, or the MK_MESSAGE SCB can be
queued due to the execution queue draining due to
aborts.
Enable LQOBUSFREE status to assert an interrupt.
This should be redundant since a BUSFREE interrupt
should always occur along with an LQOBUSFREE event,
but on the Rev A, this doesn't seem to be guaranteed.
When a PPR request is rejected when a previously
existing packetized agreement is in place, assume
that the target has been reset without our knowledge
and revert to async/narrow transfers. This corrects
two issues: the stale ENATNO setting that was used
to send the PPR is cleared so the firmware is not
confused by a future packetized selection with
ATN asserted but no MK_MESSAGE flag in the SCB and
it speeds up recovery by aborting any pending
packetized transactions that by definition are now
dead.
When re-queueing SCBs after a failed negotiation
attempt, ensure command ordering by freezing the
device queue first.
Traverse the list of pending SCBs rather than the
whole SCB array on the controller when pushing
MK_MESSAGE flag changes out to the controller.
The original code was optimized for the aic7xxx
controllers where there are fewer controller slots
then pending SCBs and the firmware picks SCB
slots. For the U320 controller, the hope is
that we have fewer pending SCBs then the 512
slots on the controller.
Enhance some diagnostics.
Factor out some common code.
aic79xx.h:
Add prototype for new ahd_done_with_status() that is
used to factor out some commone code.
aic79xx.reg:
Add definisions for the pending MK_MESSAGE SCB.
aic79xx.seq:
Defer MK_MESSAGE SCB queing to the execution queue
so as to preserve command ordering. Re-arrange some
of the selection processing code so the above change
had no performance impact on the common code path.
Close a few critical section holes.
When entering a non-packetized phase, manually enable
busfree interrupts, since the controller hardware
does not do this automatically.
aic79xx_inline.h:
Enhance logging for queued SCBs.
aic79xx_osm.c:
Add new a new DDB ahd command, ahd_dump, which
invokes the ahd_dump_card_state() routine on the
unit specified with the ahd_sunit DDB command.
aic79xx_pci.c:
Turn on the BUSFREEREV bug for the Rev B. controller.
This is required to close the busfree during non-packetized
phase hole.
into single-user mode (as seen on sparc64 and PPC). Problems were due
to a minor oversight in the changes committed in revision 1.25.
Submitted by: grehan
Tested by: gad & yongari
unconditionally, stop after the first one (system board) if no EISA hardware
is detected. This fixes a boot hang (i.e. Thinkpad) when ACPI is disabled.
Also, split the probe code into a separate function and do some style cleanup.
Note that the Adaptec 2842 VLB controller probe is broken by this change
and will fail to probe. It should be fixed separately.
in case of a CHECK CONDITION.
- Make this driver return SCSI status information.
- While here, factor out the clearing of the CAM status from every
element of the switch statement to only once before the switch.
This fixes burning CDs with recent cdrecord 2.01 alpha versions and
burners attached to asr(4) controllers but there could have been
other applications and da(4) etc. also affected.
Reviewed by: gibbs, scottl
MFC after: 2 weeks
skip blocks that are too big by a factor of two or greater. This
avoids some cases of extremely inefficient memory use that can occur
when large (e.g. 64k) blocks on the free list get used when allocating
a 4k chunk of 64-byte fragments. Because fragments have their own
free list, the 60k difference got lost forever every time.
system BIOS to disable legacy device emulation as per the "EHCI
Extended Capability: Pre-OS to OS Handoff Synchronisation" section
of the EHCI spec. BIOSes that implement legacy emulation using SMIs
are supposed to disable the emulation when this procedure is performed.
so that they know whether the allocation is supposed to be able to sleep
or not.
* Allow uma_zone constructors and initialation functions to return either
success or error. Almost all of the ones in the tree currently return
success unconditionally, but mbuf is a notable exception: the packet
zone constructor wants to be able to fail if it cannot suballocate an
mbuf cluster, and the mbuf allocators want to be able to fail in general
in a MAC kernel if the MAC mbuf initializer fails. This fixes the
panics people are seeing when they run out of memory for mbuf clusters.
* Allow debug.nosleepwithlocks on WITNESS to be disabled, without changing
the default.
Both bmilekic and jeff have reviewed the changes made to make failable
zone allocations work.
now, but it's possible for ndis_reset_nic() to sleep (sometimes the
MiniportReset() method returns NDIS_STATUS_PENDING and we have
to wait for completion). To get around this, execute the ndis_reset_nic()
routine in the NDIS_TASKQUEUE thread.
to be particularly correct or optimal, but it seems to be enough
to allow the attachment of USB2 hubs and USB2 devices connected via
USB2 hubs. None of the split transaction support is implemented in
our USB stack, so USB1 peripherals will definitely not work when
connected via USB2 hubs.
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
submitted version with style cleanups and changes to comments. I also
modified the ioctl interface. This version only has one ioctl (to get
the Synaptics-specific config parameters) since this is the only
information a user might want.
Submitted by: Arne Schwabe <arne -at- rfc2549.org>
* Some systems have _FDE and child floppy devices, but no _FDI. This seems
to be compatible with the standard. Don't error out if there is no _FDI.
Instead, continue on to the next device. The normal fd probe will take
care of this device.
* Some systems have _FDE but no child devices in AML. For these, add a
second pass that compares the results of _FDE to the presence of devices.
If not present, add the missing device.
* Some BIOS authors didn't read the spec. They use tape drive values for
all fdc(4) devices. Since this isn't grossly incompatible with the
required boolean value, use them. They also define the _FDE items as a
package instead of buffer. Regenerate the buffer from the package if it
is present.
Tested by: tjr, marcel
ACPI_DEBUG. This upset the ordering that acpi_probe_order() was meant to
provide, causing devices to attach before the sysresource object. This
debugging feature has been unnecessary for a while so just remove it.
Testing by: marcel
Properly wait for not busy and introduce a timeout for devices not
setting busy (as they should).
Leave a printf in there that states how long the wait was, as I'd like
to get an idea of the variations here. The time needed seems also to be
affected by whether a medium is present or not.
FOREACH_SAFE. Remove bad cast of retp and instead use an additional
arg to pass back the number of valid outputs. Use the package convenience
functions for parsing packages.
(in particular, bge(4) hasn't supported rxcsum since if_bge.c#1.5)
Clean up some aspects of capabilities usage, i.e. stop using
if_hwassist to see whether we are doing offload now because if_hwassist
is for TCP/IP layer and it is subordinate to if_capenable.
Thanks to: Aled Morris for donating a nice bge(4) NIC to me
Reviewed by: -net, -hackers (silence)
happens because the sio device was never opened and com->tp is
therefore NULL. ttygone can't swallow a NULL, so guard against that
possibility. Other places in this function make similar checks, so I
believe this is correct.
Improve child_detached a little and make it conform better to
style(9). Also, improve comment about what we'll be doing in the
future about driver_added. Soon it will be possible to kldload usb
drivers and have them attach w/o a need to disconnect/reconnect them.
the data sheets leads me to believe these will just work. Those parts
with the various media readers on them may not have the required
FreeBSD drivers that will attach to the subdevices that will be seen
on some of these parts.
PCI 1515, 1530, 1620, 4520, 6411, 6420, 7410, 7510, 7610
Prompted by: Havard Eidnes
These are from the datasheets downloaded from TI's web site.
They describe the PCI[67]x[12]1 and PCI[67]x20 parts, with and without
the smartcard enabled.
