Alpha can verify that it compiles fine there, too, this should be moved
to the MI section (or that problem fixed); I've only had x86 hardware to
est with.
Sponsored by: DARPA, NAI Labs (CBOSS project)
but time and other interests is making it hard. Open the door for
new blood and fresh tactics now that the Linuxulator has had its
facelift.
Thanks to all who contributed during my tour of duty!
src/sys/dev/an/if_an_pccard.c rev 1.10 change requires to include
"card_if.h" but Makefile doesn't know about this file. Without this,
kernel build will fail at this driver.
- Add S4BIOS sleep implementation. This will works well if MIB
hw.acpi.s4bios is set (and of course BIOS supports it and hibernation
is enabled correctly).
- Add DSDT overriding support which is submitted by takawata originally.
If loader tunable acpi_dsdt_load="YES" and DSDT file is set to
acpi_dsdt_name (default DSDT file name is /boot/acpi_dsdt.aml),
ACPI CA core loads DSDT from given file rather than BIOS memory block.
DSDT file can be generated by iasl in ports/devel/acpicatools/.
- Add new files so that we can add our proposed additional code to Intel
ACPI CA into these files temporary. They will be removed when
similar code is added into ACPI CA officially.
hooks depending on ethertype. Great for prototyping protocols.
connects to the lower and upper hooks of an ethernet type of node.
Obtained from: Monzoon Networks.
Thanks to Andre Oppermann, May 2001.
This emulates APM device node interface APIs (mainly ioctl) and
provides APM services for the applications. The goal is to support
most of APM applications without any changes.
Implemented ioctls in this commit are:
- APMIO_SUSPEND (mapped ACPI S3 as default but changable by sysctl)
- APMIO_STANDBY (mapped ACPI S1 as default but changable by sysctl)
- APMIO_GETINFO and APMIO_GETINFO_OLD
- APMIO_GETPWSTATUS
With above, many APM applications which get batteries, ac-line
info. and transition the system into suspend/standby mode (such as
wmapm, xbatt) should work with ACPI enabled kernel (if ACPI works well :-)
Reviewed by: arch@, audit@ and some guys
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
o Introduce private types for use in linux syscalls for two reasons:
1. establish type independence for ease in porting and,
2. provide a visual queue as to which syscalls have proper
prototypes to further cleanup the i386/alpha split.
Linuxulator types are prefixed by 'l_'. void and char have not
been "virtualized".
o Provide dummy functions for all syscalls and remove dummy functions
or implementations of truely obsolete syscalls.
o Sanitize the shm*, sem* and msg* syscalls.
o Make a first attempt to implement the linux_sysctl syscall. At this
time it only returns one MIB (KERN_VERSION), but most importantly,
it tells us when we need to add additional sysctls :-)
o Bump the kenel version up to 2.4.2 (this is not the same as the
KERN_VERSION MIB, BTW).
o Implement new syscalls, of which most are specific to i386. Our
syscall table is now up to date with Linux 2.4.2. Some highlights:
- Implement the 32-bit uid_t and gid_t bases syscalls.
- Implement a couple of 64-bit file size/offset bases syscalls.
o Fix or improve numerous syscalls and prototypes.
o Reduce style(9) violations while I'm here. Especially indentation
inconsistencies within the same file are addressed. Re-indenting
did not obfuscate actual changes to the extend that it could not
be combined.
NOTE: I spend some time testing these changes and found that if there
were regressions, they were not caused by these changes AFAICT.
It was observed that installing a RH 7.1 runtime environment
did make matters worse. Hangs and/or reboots have been observed
with and without these changes, so when it failed to make life
better in cases it doesn't look like it made it worse.
the cwd is looked up inside the kernel. The native getcwd() in libc
handles this in userland if __getcwd() fails.
Obtained from: NetBSD via OpenBSD
Tested by: Chris Casey <chriss@phys.ksu.edu>, Markus Holmberg <markush@acc.umu.se>
Reviewed by: Darrell Anderson <anderson@cs.duke.edu>
PR: kern/24315
blown over by the Hurricane and had a house dropped on you by the Tornado.
Now it's time to have your parade rained on by... the Typhoon!
This commit adds driver support for 3Com 3cR990 10/100 ethernet
adapters based on the Typhoon I and Typhoon II chipsets. This is actually
a port of the OpenBSD driver with many hacks by me.
No Virginia, there isn't any support for the hardware crypto yet. However
there is support for TCP/IP checksum offload and VLANs.
Special thanks go to Jason Wright, Aaron Campbell and Theo de Raadt for
squeezing enough info out of 3Com to get this written, and for doing
most of the hard work.
Manual page is included. Compiled as a module and included in GENERIC.
it may be plugged into a kernel that supports VLANs. If the kernel is
not VLAN aware, things will still work as before.
Modules don't really have option support, so this is somewhat of a hack.
- All sources are built in a single object, reducing namespace pollution.
- Kill the ready queue, and handle a busy response to mly_start in callers
rather than deferring the command.
- Improve our interaction with CAM:
- Don't advertise physical channels as SCSI busses by default.
- use the SIM queue freeze capability rather than queueing CDBs internally.
- force bus reprobe at module load time.
- Clean up more resources in mly_free.
- Tidy up debugging levels.
- Tidy up handling of events (mostly just code cleanliness).
- Use explanatory macros for operations on bus/target/channel numbers.
- Move the lance_probe function to if_lnc.c.
- Support C-NET(98)S again.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata) and nyan
No response from: Paul Richards
a KLD. Still doesn't work well except in the PCMCIA case (now if only
pccardd(8) could load and unload drivers dynamically...). Mainly, it
tries to find fdc0 on the PCI bus for whatever obscure reasons, but i
need someone who understands driver(9) to fix this. However, it's at least
already better than before, and i'm tired of maintaining too many private
changes in my tree, given the large patches bde submitted. :)
Idea of a KLD triggered by: Michael Reifenberger <root@nihil.plaut.de>
could only get a chance of testing it under 4.3, but together with the
if_oltr.c fixes at least it seems to work now. If someone has the chance
to test this under -current, please do.
Unfortunaltey, the TR code itself (if_iso88025subr.c) is not written
in a way that would allow to make a seaparate KLD out of it. By now,
just link it directly into the oltr KLD since it's probably the POLA
to be able to load the TR code together with the only TR hardware
driver we've got by now.
I've got one single unexplained panic (in doreti_switch or somewhere
there, calling a 0xc1XXXXXX address that did no longer belong to the
kernel at all) after unloading the modules once, thus i don't propose
a MFC of this module despite my testing has been done solely on 4.3,
unless someone is really going to test this stuff in -current.
gigabit ethernet controller chip. This device is used on some
fiber optic gigE cards from SMC, D-Link and Addtron. Jumbograms and
TCP/IP checksum offload on receive are supported. Hardware VLAN
filtering is not, because it doesn't play well with our existing
VLAN code. Also add manual page.
There is a 4.x version of this driver available at
http://www.freebsd.org/~wpaul/Level1/4.x if anyone feels adventurous
and wants to test it. I still need to do performance testing and
tuning with this device.
(For my next trick, I will make the 3Com 3cR990 sit up and beg.)
it with vfsload("msdos").
(The proper fix would be to rename the `msdos' file system to
`msdosfs' in VFS_SET(), and mount_msdos(8) to mount_msdosfs(8).
But that would break too many existing fstab(5) setups, and
would require a lot of unnecessary documentation and code
msdos -> msdosfs changes.)
Noticed by: markm
