kmem_free(). Note: The FreeBSD-specific code in this file has been
subsumed by the FreeBSD-specific header file, pdq_freebsd.h. That header
file already specifies the use of contigmalloc() and contigfree(). Thus,
the purpose of this change is to avoid having nonsensical examples of
FreeBSD-specific memory allocation in our source tree.
these add support for listing BSSIDs via wicontrol -l. I added code
to call OID_802_11_BSSID_LIST_SCAN to allow scanning for any nearby
wirelsss nets.
Convert from using individual mutexes to a mutex pool, created in
subr_ndis.c. This deals with the problem of drivers creating locks
in their DriverEntry() routines which might get trashed later.
Put some messages under IFF_DEBUG.
of the leftovers from the old version that really doesn't work anymore.
Add a reset function for host-end of the ATA channel. This is needed
for the SiI3112 in order to whack it back to reality if a device
locks up the SATA interface (thereby preventing that we can reset the
device). The result is that ATA now recovers from the timeouts that
happens with the SiI3112A and more or less all disks based on old
PATA electronics with a Marvell PATA->SATA converter. This includes
lots of the popular SATA dongles and the WDC Raptor disks..
I started with a year-old patch by Orlando Bassotto
<orlando.bassotto@ieo-research.it>, and ported it to 5.2-CURRENT along with
fixing the problems working with pre-Audigy cards.
signals to addresses to the child busses. Typically, ProgIf of 1
means a subtractive bridge. However, Intel has a whole lot of ones
with a ProgIf of 80 that are also subtractive. We cope with these
bridges too. This eliminates hw.pci.allow_unsupported_io_range
because that had almost the same effect as these patches (almost means
'buggy'). Remove the bogus checks for ISA bus locations: these cycles
aren't special and are only passed by transparent bridges.
We allow any range to succeed. If the range is a superset of the
range that's decoded, trim the resource to that range. Otherwise,
pass the range unchanged. This will change the location that PC Card
and CardBus cards are attached. This might bogusly cause some
overlapping allocation that wasn't present before, but the overlapping
fixes need to be in the pci level.
There's also a few formatting changes here.
which has two important flags in it: the 'allocated by NDIS' flag
and the 'media specific info present' flag. There are two Windows macros
for getting/setting media specific info fields within the ndis_packet
structure which can behave improperly if these flags are not initialized
correctly when a packet is allocated. It seems the correct thing
to do is always set the NDIS_PACKET_ALLOCATED_BY_NDIS flag on
all newly allocated packets.
This fixes the crashes with the Intel Centrino wireless driver.
My sample card now seems to work correctly.
Also, fix a potential LOR involving ndis_txeof() in if_ndis.c.
MAC address in the EEPROM, and we need to get it from OpenFirmware.
This isn't very pretty but time is lacking to do this in a better
way this near 5.2-RELEASE. This is a RELENG_5_2 candidate.
Original version by: Marius Strobl <marius@alchemy.franken.de>
Tested by: Pete Bentley <pete@sorted.org>
Reviewed by: jake
Add tcode_str[] and improve debug message.
* sbp
If max_speed is negative, use the maximum speed which the
ohci chip supports. The default max_speed is -1.
* if_fwe
If tx_speed is negative, use the maximum speed which the
ohci chip supports. The default tx_speed is 2.
the ni_dpccountlock member is an ndis_kspin_lock, not an
ndis_spin_lock (the latter is too big).
Run if_ndis.c:ndis_tick() via taskqueue_schedule(). Also run
ndis_start() via taskqueue in certain circumstances.
Using these tweaks, I can now get the Broadcom BCM5701 NDIS
driver to load and run. Unfortunately, the version I have seems
to suffer from the same bug as the SMC 83820 driver, which is
that it creates a spinlock during its DriverEntry() routine.
I'm still debating the right way to deal with this.
frame, not the first. It is probably also not safe to free the mbuf chain
as soon as the OWN bit is cleared on the first descriptor since the chip
may not be done copying the frame into the transmit FIFO. Revert the part of
of busdma conversion (if_dc.c rev 1.115) which changed dc_txeof() to look for
the status in the first descriptor and free the mbuf chain when processing
the first descriptor for the frame, and revert the matching changes elsewhere
in the driver. This part of the busdma change caused the driver to report
spurious collisions and output errors, even when running in full-duplex mode.
Reverting the mbuf chain handling slightly complicates dc_dma_map_txbuf(),
since it is responsible for setting the OWN bits on the descriptors, but does
not normally have direct access to the mbuf chain.
Tested by:
Dejan Lesjak <dejan.lesjak at ijs.si> alpha/<Intel 21143 10/100BaseTX>
"Xin LI" <delphij at frontfree.net> i386/<Macronix 98713 10/100BaseTX>
Wiktor Niesiobedzki <bsd at w.evip.pl> i386/<3Com OfficeConnect 10/100B>
Reviewed by: mux
additions to sys/amd64/isa/icu.h from PIIX4 and other datasheets. I
tweaked a few comments based on the NetBSD header of the same name when I
merged the constants to sys/i386/isa/icu.h, but the vast majority of this
file was created independently by Peter and not taken from any existing
files.
Submitted by: peter
the RT_MESSAGETABLE resources that some driver binaries have.
This allows us to print error messages in ndis_syslog().
- Correct the implementation of InterlockedIncrement() and
InterlockedDecrement() -- they return uint32_t, not void.
- Correct the declarations of the 64-bit arithmetic shift
routines in subr_ntoskrnl.c (_allshr, allshl, etc...). These
do not follow the _stdcall convention: instead, they appear
to be __attribute__((regparm(3)).
- Change the implementation of KeInitializeSpinLock(). There is
no complementary KeFreeSpinLock() function, so creating a new
mutex on each call to KeInitializeSpinLock() leaks resources
when a driver is unloaded. For now, KeInitializeSpinLock()
returns a handle to the ntoskrnl interlock mutex.
- Use a driver's MiniportDisableInterrupt() and MiniportEnableInterrupt()
routines if they exist. I'm not sure if I'm doing this right
yet, but at the very least this shouldn't break any currently
working drivers, and it makes the Intel PRO/1000 driver work.
- In ndis_register_intr(), save some state that might be needed
later, and save a pointer to the driver's interrupt structure
in the ndis_miniport_block.
- Save a pointer to the driver image for use by ndis_syslog()
when it calls pe_get_message().
