Enhanced Disk Drive Specification Ver 3.0 defines that the version
of extension in AH would be 30h.
Correct the check for that to be >=30h instead of >3h.
MFC after: 2 months
defined. This lets each boot program choose which version of cgbase() it
wants to use rather than forcing ufsread.c to have that knowledge.
MFC after: 1 week
Discussed with: imp
saves about 500 bytes in the boot code. While the AT91RM9200 has 12k
of space for the boot loader, which is more than i386's 8k, the code
generated by gcc is a bit bigger.
I've had this in p4 for about two years now.
Rework the read/write support in the bios disk driver some to cut down
on duplicated code.
- All of the bounce buffer and retry logic duplicated in bd_read() and
bd_write() are merged into a single bd_io() routine that takes an
extra direction argument. bd_read() and bd_write() are now simple
wrappers around bd_io().
order. The kernel used to shuffle them around to get things right,
but that was recently fixed. This makes our boot loader match the
behavior of most other boot loaders for the atmel parts. This bug was
inherited from the Kwikbyte loader that we started from.
This bug was discovered by Bj.ANvrn KNvnig back in June, but fell on the
floor. He provided patches to the kernel, include backwards
compatibility options that were similar to Olivier's if_ate.c commit.
on i386 and amd64 machines. The overall process is that /boot/pmbr lives
in the PMBR (similar to /boot/mbr for MBR disks) and is responsible for
locating and loading /boot/gptboot. /boot/gptboot is similar to /boot/boot
except that it groks GPT rather than MBR + bsdlabel. Unlike /boot/boot,
/boot/gptboot lives in its own dedicated GPT partition with a new
"FreeBSD boot" type. This partition does not have a fixed size in that
/boot/pmbr will load the entire partition into the lower 640k. However,
it is limited in that it can only be 545k. That's still a lot better than
the current 7.5k limit for boot2 on MBR. gptboot mostly acts just like
boot2 in that it reads /boot.config and loads up /boot/loader. Some more
details:
- Include uuid_equal() and uuid_is_nil() in libstand.
- Add a new 'boot' command to gpt(8) which makes a GPT disk bootable using
/boot/pmbr and /boot/gptboot. Note that the disk must have some free
space for the boot partition.
- This required exposing the backend of the 'add' function as a
gpt_add_part() function to the rest of gpt(8). 'boot' uses this to
create a boot partition if needed.
- Don't cripple cgbase() in the UFS boot code for /boot/gptboot so that
it can handle a filesystem > 1.5 TB.
- /boot/gptboot has a simple loader (gptldr) that doesn't do any I/O
unlike boot1 since /boot/pmbr loads all of gptboot up front. The
C portion of gptboot (gptboot.c) has been repocopied from boot2.c.
The primary changes are to parse the GPT to find a root filesystem
and to use 64-bit disk addresses. Currently gptboot assumes that the
first UFS partition on the disk is the / filesystem, but this algorithm
will likely be improved in the future.
- Teach the biosdisk driver in /boot/loader to understand GPT tables.
GPT partitions are identified as 'disk0pX:' (e.g. disk0p2:) which is
similar to the /dev names the kernel uses (e.g. /dev/ad0p2).
- Add a new "freebsd-boot" alias to g_part() for the new boot UUID.
MFC after: 1 month
Discussed with: marcel (some things might still change, but am committing
what I have so far)
on duplicated code and support 64-bit LBAs for GPT.
- The code to manage an EDD or C/H/S I/O request are now in their own
routines. The EDD routine now handles a full 64-bit LBA instead of
truncating LBAs to the lower 32-bits. (MBRs and BSD labels only
have 32-bit LBAs anyway, so the only LBAs ever passed down were 32-bit).
- All of the bounce buffer and retry logic duplicated in bd_read() and
bd_write() are merged into a single bd_io() routine that takes an
extra direction argument. bd_read() and bd_write() are now simple
wrappers around bd_io().
- If a disk supports EDD then always use it rather than only using it if
the cylinder is > 1023. Other parts of the boot code already do
something similar to this. Also, GPT just uses LBAs, so for a GPT disk
it's probably best to ignore C/H/S completely. Always using EDD when
it is supported by a disk is an easy way to accomplish this.
MFC after: 1 week
Slightly cleanup the 'bootdev' concept on x86 by changing the various
macros to treat the 'slice' field as a real part of the bootdev instead
of as hack that spans two other fields (adaptor (sic) and controller)
that are not used in any modern FreeBSD boot code.
macros to treat the 'slice' field as a real part of the bootdev instead
of as hack that spans two other fields (adaptor (sic) and controller)
that are not used in any modern FreeBSD boot code.
MFC after: 1 week
Add support for the CENTIPAD board (http://www.harerod.de/centipad/index.html)
(which is a very cool, very small ARM board)
Add support for KB9202B (it has different memory)
Make BOOT_FLAVOR settable
Minor cleanup nits
Approved by: re@
of obtaining them over and over again and pretending we could do
anything useful without them (for chosen this includes adding a
declaration and initializing it in OF_init()).
- In OF_init() if obtaining the memory or mmu handle fails just call
OF_exit() instead of panic() as the loader hasn't initialized the
console at these early stages yet and trying to print out something
causes a hang. With OF_exit() one at least has a change to get back
to the OFW boot monitor and debug the problem.
- Fix OF_call_method() on 64-bit machines (this is a merge of
sys/dev/ofw/openfirm.c rev 1.6).
- Replace OF_alloc_phys(), OF_claim_virt(), OF_map_phys() and
OF_release_phys() in the MI part of the loader with wrappers around
OF_call_method() in the sparc64. Beside the fact that they duplicate
OF_call_method() the formers should never have been in the MI part
of the loader as contrary to the OFW spec they use two-cell physical
addresses.
- Remove unused functions which are also MD dupes of OF_call_method().
- In sys/boot/sparc64/loader/main.c add __func__ to panic strings as
different functions use otherwise identical panic strings and make
some of the panic strings a tad more user-friendly instead of just
mentioning the name of the function that returned an unexpected
result.
- Add missing prototypes.
- Define global variables not used outside of this module as static.
- Replace some outdated hard-coded functions names in panic strings
with __func__.
- Fix some style(9) bugs.
It is disabled by default. You need to put
LOADER_FIREWIRE_SUPPORT=yes in /etc/make.conf
and rebuild loader to enable it.
(cd /sys/boot/i386 && make clean && make && make install)
You can find a short introduction of dcons at
http://wiki.freebsd.org/DebugWithDcons
speculative loads. This at least makes control speculative loads
work. In the future we should analyze which faults/exceptions
we want to handle rather than defer to avoid having to call the
recovery code when it's not strictly necessary.
- Added magic numbers to pretend the NEC original program version
2.70.
- Added string display routine with Shift-JIS code support.
- Added three nop instructions at start1 in start.s since the
installaer of the IPLware put 'call $0x09ab' instruction.
- Put the near return instruction at 0x9ab in selector.s.
Since the Shit-JIS display routine must be located at 0x1243, the
linker script file (ldscript) is applied.
bootinfo variable declaration visible. It conflicts with static
declaration in this file. Declare variable as globally visible in
order to resolve the conflict.
GetSeconds(). Instead, use CRTR register shifted right 15. This
gives us a range of 32 seconds we can do for timeout.
Shift to using == rather than < or > for calculating the timeout,
since if we can't read the ST_CTRT register twice in a second we have
even bigger problems to worry about, and == deals with the 'wrap'
issue.
This lets me type at the boot2 prompt again! Woo Hoo!
Bogusness noticed by: tisco
Pointy Hat to: That silly imp guy
CSD is usually 512 (well, 9), but for 2GB (and the rogue 4GB SD cards)
it is 1024 (or 2048 for 4GB). This value doesn't work for the block
read commands (which really want 512). Hardcode 512 for those. This
may break really old MMC cards that don't have a 512 block size (I've
never seen one: make my day and send me one :-), but since the MMC
side of the house is currently broken, it should only have the effect
that 2GB (and non-conforming 4GB) SD cards will work.
My 'non-conforming' 4GB SD card also works now too. The
non-conforming 4GB SD cards were sold for a while before the SD
association was worried they would be (a) incompatible (different FAT
flavor on them) and (b) confusing for the new SDHC standard and
cracked down on suppliers' bogus use of the SD trademark...
The changes to getstr() is so that the character that is
passed in to it, is also processed just as the rest. I also
removed one of the getc() calls otherwise you loose every
second character.
I also changed the strcpy of kname, so that it only happens if
kname is '\0'. This is so that one can pass a kernel in
through /boot.config.
The last change to boot2.c is in parse(). If you tried to type
a kernel name to boot, the first character was lost, the arg--
fix that.
Submitted by: jhay
bioscom is called to set up serial port parameters because COMSPEED
was treated as an address instead of an immediate value, causing
serial port parameters to never be set.
PR: i386/110828
Reviewed by: jhb
MFC after: 2 weeks
The relevant changes for FreeBSD (excerpt from the release note):
* Newly implemented CORE EXT words: CASE, OF, ENDOF, and ENDCASE. Also
added FALLTHROUGH, which works like ENDOF but jumps to the instruction
just after the next OF.
* Bugfix: John-Hopkins locals syntax now accepts | and -- in the comment
(between the first -- and the }.)
* Bugfix: Changed vmGetWord0() to make Purify happier. The resulting
code is no slower, no larger, and slightly more robust.
I created and tested this with a custom FreeSBIE cd-image.
PR: i386/96452
Submitted by: Yuichiro Goto <y7goto at gmail dot com>
MFC after: 3 days
Approved by: imp (mentor)
rather than treating them as a fatal exception and halting. At least one
storage BIOS (some newer mpt(4) parts) have a breakpoint instruction in
their disk read routine.
MFC after: 3 days
1. Make libefi portable by removing ia64 specific code and build
it on i386 and amd64 by default to prevent regressions. These
changes include fixes and improvements over previous code to
establish or improve APIs where none existed or when the amount
of kluging was unacceptably high.
2. Increase the amount of sharing between the efi and ski loaders
to improve maintainability of the loaders and simplify making
changes to the loader-kernel handshaking in the future.
The version of the efi and ski loaders are now both changed to 1.2
as user visible improvements and changes have been made.
to get the physical address doesn't work for all values of KVA_PAGES,
while masking 8 MSBs works for all values of KVA_PAGES that are
multiple of 4 for non-PAE and 8 for PAE. (This leaves us limited
with 12MB for non-PAE kernels and 14MB for PAE kernels.)
To get things right, we'd need to subtract the KERNBASE from the
virtual address (but KERNBASE is not easy to figure out from here),
or have physical addresses set properly in the ELF headers.
Discussed with: jhb
device (kind) specific unit field to the common field. This change
allows a future version of libefi to work without requiring anything
more than what is defined in struct devdesc and as such makes it
possible to compile said version of libefi for different platforms
without requiring that those platforms have identical derivatives
of struct devdesc.
are no longer limited to a virtual address space of 16 megabytes,
only mask high two bits of a virtual address. This allows to load
larger kernels (up to 1 gigabyte). Not masking addresses at all
was a bad idea on machines with less than >3G of memory -- kernels
are linked at 0xc0xxxxxx, and that would attempt to load a kernel
at above 3G. By masking only two highest bits we stay within the
safe limits while still allowing to boot larger kernels.
(This is a safer reimplmentation of sys/boot/i386/boot2/boot.2.c
rev. 1.71.)
Prodded by: jhb
Tested by: nyan (pc98)
Massive update. The highlights:
o dramatically cut memory usage by writing better, less intertwingled
code.
o implement booting off mmc/sd cards (sd only tested one at the moment)
o start to split out board specific stuff for boot2.
commits. For some reason I thought the scale factor was a shift count
rather than the multiplicand (that is, I thought leal (%eax,%edx,4) was
going to generate %eax + %edx << 4 rather than %eax + %edx * 4). What
I need is to multiply by 16 to convert a real-mode (seg, offset) tuple
into a flat address. However, the max multiplicand for scaled/index
addressing on i386 is 8, so go back to using a shl and an add.
- Convert two more inter-register mov instructions where we don't need to
preserve the source register to xchg instructions to keep our space
savings.
Tested by: Ian FREISLICH if at hetzner.co.za
MFC after: 1 week
another 16 bytes off of BTX (and thus boot2):
- Compare against the value of %eax that is saved on the stack instead of
loading it into %eax (which requires saving the current %eax on the
stack).
- Use %ch to examine the keyboard flag state in the BIOS to see if
Ctrl-Alt-Del is pressed instead of %al so we don't have to save %eax on
the stack anymore.
MFC after: 1 week
BTX (and thus boot2):
- Don't bother saving %eax, %ebx, or %ecx as it is not necessary.
- Use a more compact sequence to load the base value out of a GDT entry
by loading the contiguous low 24 bits into the upper 24 bits of %eax,
loading the high 8 bits into %al, and using a ror to rotate the bits
(2 mov's and a ror) rather than loading the pieces in smaller chunks
(3 mov's and a shl).
- Use movzwl + leal instead of movl + movw + shll + addl.
- Use 'xchgl %eax,%foo' rather than 'movl %eax,%foo' for cases where
it's ok to trash %eax. xchgl %eax, foo is a 1-byte opcode whereas the
mov is a 2-byte opcode.
- Use movzwl rather than xorl + movw.
MFC after: 1 week
rather than just emulating mov cr0, eax. This fixes some Compaq/HP BIOS
with DMA (as the BIOS tried to read cr3 so it could translate addresses
if paging was enabled).
MFC after: 1 week
sync() and sync_fsync() without losing MNT_ASYNC. Add MNTK_ASYNC flag
which is set only when MNT_ASYNC is set and mnt_noasync is zero, and
check that flag instead of MNT_ASYNC before initiating async io.
- Make the PROBE_KEYBOARD option better resemble the -P option in
boot2, i.e., if keyboard isn't present then boot with both
RB_SERIAL and RB_MULTIPLE set.
Reviewed by: jhb
8k boundary with this program still.
text data bss dec hex filename
7925 4 4476 12405 3075 bootiic.out
so we have like 293 bytes left before we have to play games. There
may be ways to reduce that somewhat, but they start to be very board
specific.
changes in the future. This helps with getting started and to
overcome the really sucky level of granuality this timeout has in
getc. A timeout of 1 means 'wait until top of next second' rather
than 'wait for at least a second'.
fixes filesystem corruption when nextboot.conf is located after
cylinder 1023. The bug appears to have been introduced at the time
bd_read was copied to create bd_write.
PR: bin/98005
Reported by: yar
MFC after: 1 week
selection and not always beeping on startup. The two bytes for the extra
'jmp' instruction were obtained by removing recognition of BSD/OS
partitions.
Requested by: many
Tested by: subset of many
Head nod: imp, keramida
MFC after: 2 weeks
Make this compile, assuming that you have linux installed in a
sensible place. tag_list is disabled by default, since we don't
distribute linux, but it is desirable to allow the boot loader to boot
Linux or FreeBSD (mostly for testing).
xmodem download. Then download the image you want in the flash.
This will burn the image into the flash. You must then reset the
unit and the new flash image will be used for booting...
xmodem download. Then download the image you want in the eeprom.
This will burn the image into the eeprom. You must then reset the
unit and the new eeprom image will be used for booting...
o Use a directory layout that is more akin to the i386 boot layout.
o Create a libat91 for library routines that are used by one or more
of the boot loaders.
o Create bootiic for booting from an iic part.
o Create bootspi for booting from an spi part.
o Optimize the size of many of these routines (especially emac.c). Except
for the emac.c optimizations, all these have been tested.
o eliminate the inc directory, libat91 superceeds it.
o Move linker.cfg up a layer to allow it to be shared.
For 32-bit SDRAM systems, enable D16 to D31 in the PIO controller.
Otherwise they read back as 0xffff.
Shave 8 bytes from the object size by using AT91C_BASE_PIOA directly
and by not assigning PIO_BSR to 0 in the DBGU init. That's a nop in
two ways (everything defaults to peripheral A, and writing 0 changes
nothing).
Many places used #define FOO ((unsigned int) 0x23) where a simpler
#define FOO 0x23u would have sufficed. This practice is overly
verbose and has the disadvantage that you can't say
#if FOO == BAR
#endif
because the extra "unsigned int" tokens choke cpp's little brain.
Migrate to the latter style to allow use in preprocessor statements.
The two are the same semantically anyway in a C context (at least for
the uses they are put to presently, C gurus can explain to me how they
differ).
via xmodem to the DBGU port when the AT91 comes up in recovery mode.
The recovery loader will then load your program via xmodem into SDRAM
at 1MB which can do its things. It needs to be tweaked to the
specific board one is using, but it fits in < 1kB (all of Atmel's ARM
products have at least 8kb of SRAM that I can tell, so this should
work for them all).
Parts of this code were provided by Kwikbyte with copyright
specifically disclaimed. I heavily modified it to act as a recovery
loader (before it was a bootstrap loader) and to optimize for size
(before I started the size was closer to 8k).
Bootstrap loaders for SPI and IIC to follow.
Otherwise, we could match on a filename that had the wrong last character
(such as /boot/loaded instead of /boot/loader).
PR: kern/95625
Submitted by: Oliver Fromme <olli@secnetix.de>
MFC after: 1 month
controller to get ready (65K x ISA access time, visually around 1 second).
If we have wait more than that amount it's likely that the hardware is a
legacy-free one and simply doesn't have keyboard controller and doesn't
require enabling A20 at all.
This makes cdboot working for MacBook Pro with Boot Camp.
MFC after: 1 day
Use 'BOOT_SENSITIVE_INFO=YES' variable to turn them on.
- Use 'uint*_t' instead of 'u_int*_t', correct compilation warnings, and
update copyright while I am here.
when checking whether it's greater than a struct stat st_size in order
to also catch the case when st_size is -1. Previously this check didn't
trigger on sparc64 when st_size is -1 (as it's the case for a file on
a bzipfs, TFTP server etc.), causing the content of the linker hints
file to be copied to memory referenced by a null-pointer.
PR: 91231
MFC after: 1 week
3MB of physical memory for heap instead of range between 1MB and 4MB.
This makes this feature working with PAE and amd64 kernels, which are
loaded at 2MB. Teach i386_copyin() to avoid using range allocated by
heap in such case, so that it won't trash heap in the low memory
conditions.
This should make loading bzip2-compressed kernels/modules/mfs images
generally useable, so that re@ team is welcome to evaluate merits
of using this feature in the installation CDs.
Valuable suggestions by: jhb
provide enough room for decompression (up to 2.5MB is necessary). This
should be safe to do since we load i386 kernels after 8MB mark now, so
that 16MB is the minimum amount of RAM necessary to even boot FreeBSD.
This makes bzip2-support practically useable.
memory directly available to loader(8) and friends was limited to 640K on i386.
Those times have passed long time ago and now loader(8) can directly access
up to 4GB of RAM at least theoretically. At the same time, there are several
places where it's assumed that malloc() will only allocate memory within
first megabyte.
Remove that assumption by allocating appropriate bounce buffers for BIOS
calls on stack where necessary.
This allows using memory above first megabyte for heap if necessary.
means:
o Remove Elf64_Quarter,
o Redefine Elf64_Half to be 16-bit,
o Redefine Elf64_Word to be 32-bit,
o Add Elf64_Xword and Elf64_Sxword for 64-bit entities,
o Use Elf_Size in MI code to abstract the difference between
Elf32_Word and Elf64_Word.
o Add Elf_Ssize as the signed counterpart of Elf_Size.
MFC after: 2 weeks
devices can be opened multiple times simultaneously but we're
expected to be able to do so by the rest of the loader.
This fixes booting from disks attached to the on-board SCSI
controller of Sun Ultra 1 (previously this triggered a trap)
and probably also of AX1115 boards.
- While here, remove unused variables and add empty lines where
style(9) requires such.
Tested on: powerpc (grehan), sparc64
MFC after: 1 month
> Cause all flags passed by boot2 to set the respective loader(8)
> boot_* variable. The end effect is that all flags from boot2
> are now passed to the kernel.
the serial console speed (i386 and amd64 only). If the previous
stage boot loader requested a serial console (RB_SERIAL or RB_MULTIPLE)
then the default speed is determined from the current serial port
speed. Otherwise it is set to 9600 or the value of BOOT_COMCONSOLE_SPEED
at compile time.
This makes it possible to set the serial port speed once in
/boot.config and the setting will propagate to boot2, loader and
the kernel serial console.
/boot.config or on the "boot:" prompt line via a "-S<speed>" flag,
e.g. "-h -S19200". This adds about 50 bytes to the size of boot2
and required a few other small changes to limit the size impact.
This changes only affects boot2; there are further loader changes
to follow.
which serial device to use in that case respectively to not rely on
the OFW names of the input/output and stdin/stdout devices. Instead
check whether input and output refers to the same device and is of
type serial (uart(4) was already doing this) and for the fallback
to a serial console in case a keyboard is the selected input device
but unplugged do the same for stdin and stdout in case the input
device is nonexistent (PS/2 and USB keyboards) or has a 'keyboard'
property (RS232 keyboards). Additionally also check whether the OFW
did a fallback to a serial console in the same way in case the
output device is nonexistent. While at it save on some variables
and for sys/boot/sparc64/loader/metadata.c move the code in question
to a new function md_bootserial() so it can be kept in sync with
uart_cpu_getdev_console() more easily.
This fixes selecting a serial console and the appropriate device
when using a device path for the 'input-device' and 'output-device'
OFW environment variables instead of an alias for the serial device
to use or when using a screen alias that additionally denotes a
video mode (like e.g. 'screen:r1024x768x60') but no keyboard is
plugged in (amongst others). It also makes the code select a serial
console in case the OFW did the same due to a misconfiguration like
both 'input-device' and 'output-device' set to 'keyboard' or to a
nonexisting device (whether the OFW does a fallback to a serial
console in case of a misconfiguration or one ends up with just no
console at all highly depends on the OBP version however).
- Reduce the size of buffers that only ever need to hold the string
'serial' accordingly. Double the size of buffers that may need to
hold a device path as e.g. '/pci@8,700000/ebus@5/serial@1,400000:a'
exceeds 32 chars.
- Remove the package handle of the '/options' node from the argument
list of uart_cpu_getdev_dbgport() as it's unused there and future
use is also unlikely.
MFC after: 1 week
