This manpage isn't differentiated from mlx4en except where necessary,
replacing eth/ETH with ib/IB.
Eventually the manpages will be split and the common bits be placed
in a manpage named "mlx4.4".
MFC after: 3 weeks
Reviewed by: hselasky
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9241
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
The sysctl controls the period per interface.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9153
drain timeout handling to historical freebsd behavior.
The primary reason for these changes is the need to have tty_drain() call
ttydevsw_busy() at some reasonable sub-second rate, to poll hardware that
doesn't signal an interrupt when the transmit shift register becomes empty
(which includes virtually all USB serial hardware). Such hardware hangs
in a ttyout wait, because it never gets an opportunity to trigger a wakeup
from the sleep in tty_drain() by calling ttydisc_getc() again, after
handing the last of the buffered data to the hardware.
While researching the history of changes to tty_drain() I stumbled across
some email describing the historical BSD behavior of tcdrain() and close()
on serial ports, and the ability of comcontrol(1) to control timeout
behavior. Using that and some advice from Bruce Evans as a guide, I've
put together these changes to implement the hardware polling and restore
the historical timeout behaviors...
- tty_drain() now calls ttydevsw_busy() in a loop at 10 Hz to accomodate
hardware that requires polling for busy state.
- The "new historical" behavior for draining during close(2) is retained:
the drain timeout is "1 second without making any progress". When the
1-second timeout expires, if the count of bytes remaining in the tty
layer buffer is smaller than last time, the timeout is extended for
another second. Unfortunately, the same logic cannot be extended all
the way down to the hardware, because the interface to that layer is a
simple busy/not-busy indication.
- Due to the previous point, an application that needs a guarantee that
all data has been transmitted must use TIOCDRAIN/tcdrain(3) before
calling close(2).
- The historical behavior of honoring the drainwait setting for TIOCDRAIN
(used by tcdrain(3)) is restored.
- The historical kern.drainwait sysctl to control the global default
drainwait time is restored, but is now named kern.tty_drainwait.
- The historical default drainwait timeout of 300 seconds is restored.
- Handling of TIOCGDRAINWAIT and TIOCSDRAINWAIT ioctls is restored
(this also makes the comcontrol(1) drainwait verb work again).
- Manpages are updated to document these behaviors.
Reviewed by: bde (prior version)
- Update struct link_settings and associated shared code.
- Add tunables to control FEC and autonegotiation. All ports inherit
these values as their initial settings.
hw.cxgbe.fec
hw.cxgbe.autoneg
- Add per-port sysctls to control FEC and autonegotiation. These can be
modified at any time.
dev.<port>.<n>.fec
dev.<port>.<n>.autoneg
MFC after: 3 days
Sponsored by: Chelsio Communications
- Drop uses of 'will'.
- Replace 'to use' with active voice.
- Tidy language around interrupt types and clarify that INTx doesn't
work on VFs.
- Drop leading articles from sysctl/tunable descriptions.
- Tweak the wording of several sysctl/tunable descriptions.
Submitted by: wblock (1, 2, 4)
Sponsored by: Chelsio Communications
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D8812
FC-Tape provides additional link level error recovery, and is
highly recommended for tape devices. It will only be turned on for
a given target if the target supports it.
Without this setting, we default to whatever FC-Tape setting is in
NVRAM on the card.
This can be overridden by setting the following loader tunable, for
example for isp0:
hint.isp.0.nofctape=1
sys/conf/options:
Add a new kernel config option, ISP_FCTAPE_OFF, that
defaults the FC-Tape configuration to off.
sys/dev/isp/isp_pci.c:
If ISP_FCTAPE_OFF is defined, turn off FC-Tape. Otherwise,
turn it on if the card supports it.
share/man/man4/isp.4:
Add a description of FC-Tape to the isp(4) man page.
Add descriptions of the fctape and nofctape options, as well as the
ISP_FCTAPE_OFF kernel configuration option.
Add the ispfw module and kernel drivers to the suggested
configurations at the top of the man page so that users are less
likely to leave it out. The driver works well with the included
firmware, but may not work at all with whatever firmware the user
has flashed on their card.
MFC after: 3 days
Sponsored by: Spectra Logic
- It should say 'read' in the I2CREAD section.
- last in the struct indicates the last command in a sequence, not the
reverse.
Reviewed by: imp
MFC after: 3 days
We shouldn't install them on the architectures not supported by Hyper-V.
And, hv_ata_pci_disengage.4.gz should be removed from all architectures:
1) It should have only applied to Hyper-V;
2) For Hyper-V platforms (amd64 and i386), the related driver was removed by
r306426 | sephe | 2016-09-29 09:41:52 +0800 (Thu, 29 Sep 2016),
because now we have a better mechanism to disble the ata driver for hard
disks when the VM runs on Hyper-V.
Reviewed by: sephe, andrew, jhb
Approved by: sephe (mentor)
MFC after: 3 days
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8572
on the AES-NI code, and modified as needed for use on ARMv8. When loaded
the driver will check the appropriate field in the id_aa64isar0_el1
register to see if AES is supported, and if so the probe function will
signal the driver should attach.
With this I have seen up to 2000Mb/s from the cryptotest test with a single
thread on a ThunderX Pass 2.0.
Reviewed by: imp
Obtained from: ABT Systems Ltd
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8297
We need to remove the line since we removed the related manual just now.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
A few months ago, we removed the driver, which was not necessary any longer.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
We enhanced the vmbus driver to support PCIe pass-through recently.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
VSS stands for "Volume Shadow Copy Service". Unlike virtual machine
snapshot, it only takes snapshot for the virtual disks, so both
filesystem and applications have to aware of it, and cooperate the
whole VSS process.
This driver exposes two device files to the userland:
/dev/hv_fsvss_dev
Normally userland programs should _not_ mess with this device file.
It is currently used by the hv_vss_daemon(8), which freezes and
thaws the filesystem. NOTE: currently only UFS is supported, if
the system mounts _any_ other filesystems, the hv_vss_daemon(8)
will veto the VSS process.
If hv_vss_daemon(8) was disabled, then this device file must be
opened, and proper ioctls must be issued to keep the VSS working.
/dev/hv_appvss_dev
Userland application can opened this device file to receive the
VSS freeze notification, hold the VSS for a while (mainly to flush
application data to filesystem), release the VSS process, and
receive the VSS thaw notification i.e. applications can run again.
The VSS will still work, even if this device file is not opened.
However, only filesystem consistency is promised, if this device
file is not opened or is not operated properly.
hv_vss_daemon(8) is started by devd(8) by default. It can be disabled
by editting /etc/devd/hyperv.conf.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Reviewed by: kib, mckusick
MFC after: 3 weeks
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8224
- Increase Rx buffer size from MCLBYTES to MJUMPAGESIZE.
- Provide an additional defragmentation routine for frames larger
than MCLBYTES; that is required by A-MSDU / Atheros Fast-Frames
support to work with current Tx path implementation.
Enabled features list for RTL8188CE:
- Atheros Fast-Frames;
- A-MPDU (Tx / Rx);
- A-MSDU (Tx / Rx; 4k only);
- Short Guard Interval.
Tested with:
- RTL8188CE (STA+AP) + RTL8821AU (STA).
- RTL8188CE (STA) + RTL8188CUS (AP).
Relnotes: yes
After removal of SMB_TRANS some information in the description of
SMB_BWRITE has become stale. E.g., the maximum block size has been
restored to 32.
Also, the descriptions of SMB_BREAD and SMB_BWRITE had some
incorrect information on the SMBus protocol details.
MFC after: 1 week
X-MFC with: r308242
Differential Revision: https://reviews.freebsd.org/D8431
This change reverts most of r281985.
The method did not map to anything defined by SMBus protocol and could
not be implemented for SMBus controllers.
This change is obviously not backwards compatible, but I have good
reasons to believe that there have never been any users of SMB_TRANS.
Discussed with: grembo, jhb
MFC after: 6 weeks
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
These two ALU instructions first appeared on Linux. Then, libpcap adopted
and made them available since 1.6.2. Now more platforms including NetBSD
have them in kernel. So do we.
--이 줄 이하는 자동으로 제거됩니다--
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
This commit, long overdue, contains contributions in the last 2 years
from Stefano Garzarella, Giuseppe Lettieri, Vincenzo Maffione, including:
+ fixes on monitor ports
+ the 'ptnet' virtual device driver, and ptnetmap backend, for
high speed virtual passthrough on VMs (bhyve fixes in an upcoming commit)
+ improved emulated netmap mode
+ more robust error handling
+ removal of stale code
+ various fixes to code and documentation (some mixup between RX and TX
parameters, and private and public variables)
We also include an additional tool, nmreplay, which is functionally
equivalent to tcpreplay but operating on netmap ports.
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
