directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
Bring in updated jail support from bz_jail branch.
This enhances the current jail implementation to permit multiple
addresses per jail. In addtion to IPv4, IPv6 is supported as well.
Due to updated checks it is even possible to have jails without
an IP address at all, which basically gives one a chroot with
restricted process view, no networking,..
SCTP support was updated and supports IPv6 in jails as well.
Cpuset support permits jails to be bound to specific processor
sets after creation.
Jails can have an unrestricted (no duplicate protection, etc.) name
in addition to the hostname. The jail name cannot be changed from
within a jail and is considered to be used for management purposes
or as audit-token in the future.
DDB 'show jails' command was added to aid debugging.
Proper compat support permits 32bit jail binaries to be used on 64bit
systems to manage jails. Also backward compatibility was preserved where
possible: for jail v1 syscalls, as well as with user space management
utilities.
Both jail as well as prison version were updated for the new features.
A gap was intentionally left as the intermediate versions had been
used by various patches floating around the last years.
Bump __FreeBSD_version for the afore mentioned and in kernel changes.
Special thanks to:
- Pawel Jakub Dawidek (pjd) for his multi-IPv4 patches
and Olivier Houchard (cognet) for initial single-IPv6 patches.
- Jeff Roberson (jeff) and Randall Stewart (rrs) for their
help, ideas and review on cpuset and SCTP support.
- Robert Watson (rwatson) for lots and lots of help, discussions,
suggestions and review of most of the patch at various stages.
- John Baldwin (jhb) for his help.
- Simon L. Nielsen (simon) as early adopter testing changes
on cluster machines as well as all the testers and people
who provided feedback the last months on freebsd-jail and
other channels.
- My employer, CK Software GmbH, for the support so I could work on this.
Reviewed by: (see above)
MFC after: 3 months (this is just so that I get the mail)
X-MFC Before: 7.2-RELEASE if possible
whitespace) macros from p4/vimage branch.
Do a better job at enclosing all instantiations of globals
scheduled for virtualization in #ifdef VIMAGE_GLOBALS blocks.
De-virtualize and mark as const saorder_state_alive and
saorder_state_any arrays from ipsec code, given that they are never
updated at runtime, so virtualizing them would be pointless.
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
and ifnet functions
- add memory barriers to <machine/atomic.h>
- update drivers to only conditionally define their own
- add lockless producer / consumer ring buffer
- remove ring buffer implementation from cxgb and update its callers
- add if_transmit(struct ifnet *ifp, struct mbuf *m) to ifnet to
allow drivers to efficiently manage multiple hardware queues
(i.e. not serialize all packets through one ifq)
- expose if_qflush to allow drivers to flush any driver managed queues
This work was supported by Bitgravity Inc. and Chelsio Inc.
for virtualization.
Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.
Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
from the vimage project, as per plan established at devsummit 08/08:
http://wiki.freebsd.org/Image/Notes200808DevSummit
Introduce INIT_VNET_*() initializer macros, VNET_FOREACH() iterator
macros, and CURVNET_SET() context setting macros, all currently
resolving to NOPs.
Prepare for virtualization of selected SYSCTL objects by introducing a
family of SYSCTL_V_*() macros, currently resolving to their global
counterparts, i.e. SYSCTL_V_INT() == SYSCTL_INT().
Move selected #defines from sys/sys/vimage.h to newly introduced header
files specific to virtualized subsystems (sys/net/vnet.h,
sys/netinet/vinet.h etc.).
All the changes are verified to have zero functional impact at this
point in time by doing MD5 comparision between pre- and post-change
object files(*).
(*) netipsec/keysock.c did not validate depending on compile time options.
Implemented by: julian, bz, brooks, zec
Reviewed by: julian, bz, brooks, kris, rwatson, ...
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
When I changed kern_conf.c three months ago I made device unit numbers
equal to (unneeded) device minor numbers. We used to require
bitshifting, because there were eight bits in the middle that were
reserved for a device major number. Not very long after I turned
dev2unit(), minor(), unit2minor() and minor2unit() into macro's.
The unit2minor() and minor2unit() macro's were no-ops.
We'd better not remove these four macro's from the kernel, because there
is a lot of (external) code that may still depend on them. For now it's
harmless to remove all invocations of unit2minor() and minor2unit().
Reviewed by: kib
virtualization work done by Marko Zec (zec@).
This is the first in a series of commits over the course
of the next few weeks.
Mark all uses of global variables to be virtualized
with a V_ prefix.
Use macros to map them back to their global names for
now, so this is a NOP change only.
We hope to have caught at least 85-90% of what is needed
so we do not invalidate a lot of outstanding patches again.
Obtained from: //depot/projects/vimage-commit2/...
Reviewed by: brooks, des, ed, mav, julian,
jamie, kris, rwatson, zec, ...
(various people I forgot, different versions)
md5 (with a bit of help)
Sponsored by: NLnet Foundation, The FreeBSD Foundation
X-MFC after: never
V_Commit_Message_Reviewed_By: more people than the patch
unsynchronized. While races were extremely rare, we've now had a
couple of reports of panics in environments involving large numbers of
IPSEC tunnels being added very quickly on an active system.
- Add accessor functions ifnet_byindex(), ifaddr_byindex(),
ifdev_byindex() to replace existing accessor macros. These functions
now acquire the ifnet lock before derefencing the table.
- Add IFNET_WLOCK_ASSERT().
- Add static accessor functions ifnet_setbyindex(), ifdev_setbyindex(),
which set values in the table either asserting of acquiring the ifnet
lock.
- Use accessor functions throughout if.c to modify and read
ifindex_table.
- Rework ifnet attach/detach to lock around ifindex_table modification.
Note that these changes simply close races around use of ifindex_table,
and make no attempt to solve the probem of disappearing ifnets. Further
refinement of this work, including with respect to ifindex_table
resizing, is still required.
In a future change, the ifnet lock should be converted from a mutex to an
rwlock in order to reduce contention.
Reviewed and tested by: brooks
- verified that the ifp->if_snd.ifq_mtx was initalized for
all attached interfaces. This was pointless because it was
initalized for all interfaces in if_attach() so I've removed it.
- Checked that ifp->if_snd.ifq_maxlen is initalized and set it to
ifqmaxlen if unset. This makes more sense in if_attach() so
I moved it there.
- The first call of if_slowtimo(). Delete if_check() and call
if_slowtimo() directly from the SYSINIT().
This particular implementation is designed to be fully backwards compatible
and to be MFC-able to 7.x (and 6.x)
Currently the only protocol that can make use of the multiple tables is IPv4
Similar functionality exists in OpenBSD and Linux.
From my notes:
-----
One thing where FreeBSD has been falling behind, and which by chance I
have some time to work on is "policy based routing", which allows
different
packet streams to be routed by more than just the destination address.
Constraints:
------------
I want to make some form of this available in the 6.x tree
(and by extension 7.x) , but FreeBSD in general needs it so I might as
well do it in -current and back port the portions I need.
One of the ways that this can be done is to have the ability to
instantiate multiple kernel routing tables (which I will now
refer to as "Forwarding Information Bases" or "FIBs" for political
correctness reasons). Which FIB a particular packet uses to make
the next hop decision can be decided by a number of mechanisms.
The policies these mechanisms implement are the "Policies" referred
to in "Policy based routing".
One of the constraints I have if I try to back port this work to
6.x is that it must be implemented as a EXTENSION to the existing
ABIs in 6.x so that third party applications do not need to be
recompiled in timespan of the branch.
This first version will not have some of the bells and whistles that
will come with later versions. It will, for example, be limited to 16
tables in the first commit.
Implementation method, Compatible version. (part 1)
-------------------------------
For this reason I have implemented a "sufficient subset" of a
multiple routing table solution in Perforce, and back-ported it
to 6.x. (also in Perforce though not always caught up with what I
have done in -current/P4). The subset allows a number of FIBs
to be defined at compile time (8 is sufficient for my purposes in 6.x)
and implements the changes needed to allow IPV4 to use them. I have not
done the changes for ipv6 simply because I do not need it, and I do not
have enough knowledge of ipv6 (e.g. neighbor discovery) needed to do it.
Other protocol families are left untouched and should there be
users with proprietary protocol families, they should continue to work
and be oblivious to the existence of the extra FIBs.
To understand how this is done, one must know that the current FIB
code starts everything off with a single dimensional array of
pointers to FIB head structures (One per protocol family), each of
which in turn points to the trie of routes available to that family.
The basic change in the ABI compatible version of the change is to
extent that array to be a 2 dimensional array, so that
instead of protocol family X looking at rt_tables[X] for the
table it needs, it looks at rt_tables[Y][X] when for all
protocol families except ipv4 Y is always 0.
Code that is unaware of the change always just sees the first row
of the table, which of course looks just like the one dimensional
array that existed before.
The entry points rtrequest(), rtalloc(), rtalloc1(), rtalloc_ign()
are all maintained, but refer only to the first row of the array,
so that existing callers in proprietary protocols can continue to
do the "right thing".
Some new entry points are added, for the exclusive use of ipv4 code
called in_rtrequest(), in_rtalloc(), in_rtalloc1() and in_rtalloc_ign(),
which have an extra argument which refers the code to the correct row.
In addition, there are some new entry points (currently called
rtalloc_fib() and friends) that check the Address family being
looked up and call either rtalloc() (and friends) if the protocol
is not IPv4 forcing the action to row 0 or to the appropriate row
if it IS IPv4 (and that info is available). These are for calling
from code that is not specific to any particular protocol. The way
these are implemented would change in the non ABI preserving code
to be added later.
One feature of the first version of the code is that for ipv4,
the interface routes show up automatically on all the FIBs, so
that no matter what FIB you select you always have the basic
direct attached hosts available to you. (rtinit() does this
automatically).
You CAN delete an interface route from one FIB should you want
to but by default it's there. ARP information is also available
in each FIB. It's assumed that the same machine would have the
same MAC address, regardless of which FIB you are using to get
to it.
This brings us as to how the correct FIB is selected for an outgoing
IPV4 packet.
Firstly, all packets have a FIB associated with them. if nothing
has been done to change it, it will be FIB 0. The FIB is changed
in the following ways.
Packets fall into one of a number of classes.
1/ locally generated packets, coming from a socket/PCB.
Such packets select a FIB from a number associated with the
socket/PCB. This in turn is inherited from the process,
but can be changed by a socket option. The process in turn
inherits it on fork. I have written a utility call setfib
that acts a bit like nice..
setfib -3 ping target.example.com # will use fib 3 for ping.
It is an obvious extension to make it a property of a jail
but I have not done so. It can be achieved by combining the setfib and
jail commands.
2/ packets received on an interface for forwarding.
By default these packets would use table 0,
(or possibly a number settable in a sysctl(not yet)).
but prior to routing the firewall can inspect them (see below).
(possibly in the future you may be able to associate a FIB
with packets received on an interface.. An ifconfig arg, but not yet.)
3/ packets inspected by a packet classifier, which can arbitrarily
associate a fib with it on a packet by packet basis.
A fib assigned to a packet by a packet classifier
(such as ipfw) would over-ride a fib associated by
a more default source. (such as cases 1 or 2).
4/ a tcp listen socket associated with a fib will generate
accept sockets that are associated with that same fib.
5/ Packets generated in response to some other packet (e.g. reset
or icmp packets). These should use the FIB associated with the
packet being reponded to.
6/ Packets generated during encapsulation.
gif, tun and other tunnel interfaces will encapsulate using the FIB
that was in effect withthe proces that set up the tunnel.
thus setfib 1 ifconfig gif0 [tunnel instructions]
will set the fib for the tunnel to use to be fib 1.
Routing messages would be associated with their
process, and thus select one FIB or another.
messages from the kernel would be associated with the fib they
refer to and would only be received by a routing socket associated
with that fib. (not yet implemented)
In addition Netstat has been edited to be able to cope with the
fact that the array is now 2 dimensional. (It looks in system
memory using libkvm (!)). Old versions of netstat see only the first FIB.
In addition two sysctls are added to give:
a) the number of FIBs compiled in (active)
b) the default FIB of the calling process.
Early testing experience:
-------------------------
Basically our (IronPort's) appliance does this functionality already
using ipfw fwd but that method has some drawbacks.
For example,
It can't fully simulate a routing table because it can't influence the
socket's choice of local address when a connect() is done.
Testing during the generating of these changes has been
remarkably smooth so far. Multiple tables have co-existed
with no notable side effects, and packets have been routes
accordingly.
ipfw has grown 2 new keywords:
setfib N ip from anay to any
count ip from any to any fib N
In pf there seems to be a requirement to be able to give symbolic names to the
fibs but I do not have that capacity. I am not sure if it is required.
SCTP has interestingly enough built in support for this, called VRFs
in Cisco parlance. it will be interesting to see how that handles it
when it suddenly actually does something.
Where to next:
--------------------
After committing the ABI compatible version and MFCing it, I'd
like to proceed in a forward direction in -current. this will
result in some roto-tilling in the routing code.
Firstly: the current code's idea of having a separate tree per
protocol family, all of the same format, and pointed to by the
1 dimensional array is a bit silly. Especially when one considers that
there is code that makes assumptions about every protocol having the
same internal structures there. Some protocols don't WANT that
sort of structure. (for example the whole idea of a netmask is foreign
to appletalk). This needs to be made opaque to the external code.
My suggested first change is to add routing method pointers to the
'domain' structure, along with information pointing the data.
instead of having an array of pointers to uniform structures,
there would be an array pointing to the 'domain' structures
for each protocol address domain (protocol family),
and the methods this reached would be called. The methods would have
an argument that gives FIB number, but the protocol would be free
to ignore it.
When the ABI can be changed it raises the possibilty of the
addition of a fib entry into the "struct route". Currently,
the structure contains the sockaddr of the desination, and the resulting
fib entry. To make this work fully, one could add a fib number
so that given an address and a fib, one can find the third element, the
fib entry.
Interaction with the ARP layer/ LL layer would need to be
revisited as well. Qing Li has been working on this already.
This work was sponsored by Ironport Systems/Cisco
Reviewed by: several including rwatson, bz and mlair (parts each)
Obtained from: Ironport systems/Cisco
we're certain the allocation will entierly succeed. This fixes a leak in a
fairly unlikely case.
Reported by: vijay singh <vijjus at rocketmail dot com>
MFC after: 1 week
after each SYSINIT() macro invocation. This makes a number of
lightweight C parsers much happier with the FreeBSD kernel
source, including cflow's prcc and lxr.
MFC after: 1 month
Discussed with: imp, rink
for all network interfaces, not just ethernet-like ones.
Upgrade it to a louder WARNING and be explicit that the flag is obsolete.
Support for IFF_NEEDSGIANT will be removed in a few months (see arch@ for
details) and will not appear in 8.0.
Upgrade if_watchdog to a WARNING.
from Mac OS X Leopard--rationalize naming for entry points to
the following general forms:
mac_<object>_<method/action>
mac_<object>_check_<method/action>
The previous naming scheme was inconsistent and mostly
reversed from the new scheme. Also, make object types more
consistent and remove spaces from object types that contain
multiple parts ("posix_sem" -> "posixsem") to make mechanical
parsing easier. Introduce a new "netinet" object type for
certain IPv4/IPv6-related methods. Also simplify, slightly,
some entry point names.
All MAC policy modules will need to be recompiled, and modules
not updates as part of this commit will need to be modified to
conform to the new KPI.
Sponsored by: SPARTA (original patches against Mac OS X)
Obtained from: TrustedBSD Project, Apple Computer
framework for non-MPSAFE network protocols:
- Remove debug_mpsafenet variable, sysctl, and tunable.
- Remove NET_NEEDS_GIANT() and associate SYSINITSs used by it to force
debug.mpsafenet=0 if non-MPSAFE protocols are compiled into the kernel.
- Remove logic to automatically flag interrupt handlers as non-MPSAFE if
debug.mpsafenet is set for an INTR_TYPE_NET handler.
- Remove logic to automatically flag netisr handlers as non-MPSAFE if
debug.mpsafenet is set.
- Remove references in a few subsystems, including NFS and Cronyx drivers,
which keyed off debug_mpsafenet to determine various aspects of their own
locking behavior.
- Convert NET_LOCK_GIANT(), NET_UNLOCK_GIANT(), and NET_ASSERT_GIANT into
no-op's, as their entire behavior was determined by the value in
debug_mpsafenet.
- Alias NET_CALLOUT_MPSAFE to CALLOUT_MPSAFE.
Many remaining references to NET_.*_GIANT() and NET_CALLOUT_MPSAFE are still
present in subsystems, and will be removed in followup commits.
Reviewed by: bz, jhb
Approved by: re (kensmith)
The name trunk is misused as the networking term trunk means carrying multiple
VLANs over a single connection. The IEEE standard for link aggregation (802.3
section 3) does not talk about 'trunk' at all while it is used throughout IEEE
802.1Q in describing vlans.
The lagg(4) driver provides link aggregation, failover and fault tolerance.
Discussed on: current@
tolerance. This driver allows aggregation of multiple network interfaces as
one virtual interface using a number of different protocols/algorithms.
failover - Sends traffic through the secondary port if the master becomes
inactive.
fec - Supports Cisco Fast EtherChannel.
lacp - Supports the IEEE 802.3ad Link Aggregation Control Protocol
(LACP) and the Marker Protocol.
loadbalance - Static loadbalancing using an outgoing hash.
roundrobin - Distributes outgoing traffic using a round-robin scheduler
through all active ports.
This code was obtained from OpenBSD and this also includes 802.3ad LACP support
from agr(4) in NetBSD.
structures. Detect when ifnet instances are detached from the network
stack and perform appropriate cleanup to prevent memory leaks.
This has been implemented in such a way as to be backwards ABI compatible.
Kernel consumers are changed to use if_delmulti_ifma(); in_delmulti()
is unable to detect interface removal by design, as it performs searches
on structures which are removed with the interface.
With this architectural change, the panics FreeBSD users have experienced
with carp and pfsync should be resolved.
Obtained from: p4 branch bms_netdev
Reviewed by: andre
Sponsored by: Garance A Drosehn
Idea from: NetBSD
MFC after: 1 month
a link-layer multicast group membership.
Such memberships are needed in order to support protocols such as
IS-IS without putting the interface into PROMISC or ALLMULTI modes.
sa_equal() is not OK for comparing sockaddr_dl as it has deeper structure
than a simple byte array, so add sa_dl_equal() and use that instead.
Reviewed by: rwatson
Verified with: /usr/sbin/mtest
Bug found by: Jouke Witteveen
MFC after: 2 weeks
if_watchdog/if_timer interface doesn't fit modern SMP network
stack design.
Device drivers that need watchdog to monitor their hardware should
implement it theirselves.
Eventually the if_watchdog/if_timer API will be removed. For now,
warn that driver uses it.
Reviewed by: scottl
specific privilege names to a broad range of privileges. These may
require some future tweaking.
Sponsored by: nCircle Network Security, Inc.
Obtained from: TrustedBSD Project
Discussed on: arch@
Reviewed (at least in part) by: mlaier, jmg, pjd, bde, ceri,
Alex Lyashkov <umka at sevcity dot net>,
Skip Ford <skip dot ford at verizon dot net>,
Antoine Brodin <antoine dot brodin at laposte dot net>
begun with a repo-copy of mac.h to mac_framework.h. sys/mac.h now
contains the userspace and user<->kernel API and definitions, with all
in-kernel interfaces moved to mac_framework.h, which is now included
across most of the kernel instead.
This change is the first step in a larger cleanup and sweep of MAC
Framework interfaces in the kernel, and will not be MFC'd.
Obtained from: TrustedBSD Project
Sponsored by: SPARTA
and skip over the normal IP processing.
Add a supporting function ifa_ifwithbroadaddr() to verify and validate the
supplied subnet broadcast address.
PR: kern/99558
Tested by: Andrey V. Elsukov <bu7cher-at-yandex.ru>
Sponsored by: TCP/IP Optimization Fundraise 2005
MFC after: 3 days
parameter that can specify configuration parameters:
o rev cloner api's to add optional parameter block
o add SIOCCREATE2 that accepts parameter data
o rev vlan support to use new api (maintain old code)
Reviewed by: arch@
except in places dealing with ifaddr creation or destruction; and
in such special places incomplete ifaddrs should never be linked
to system-wide data structures. Therefore we can eliminate all the
superfluous checks for "ifa->ifa_addr != NULL" and get ready
to the system crashing honestly instead of masking possible bugs.
Suggested by: glebius, jhb, ru
list.
- First remove from global list, then start destroying.
PR: kern/97679
Submitted by: Alex Lyashkov <shadow itt.net.ru>
Reviewed by: rwatson, brooks
order to - for example - apply firewall rules to a whole group of
interfaces. This is required for importing pf from OpenBSD 3.9
Obtained from: OpenBSD (with changes)
Discussed on: -net (back in April)
notification so all interfaces including pseudo are reported. When netif
creates the clones at startup devctl_disable has not been turned off yet so the
interfaces will not be initialised twice, enforce this by adding an explicit
order between rc.d/netif and rc.d/devd.
This change allows actions to taken in userland when an interface is cloned
and the pseudo interface will be automatically configured if a ifconfig_<int>=""
line exists in rc.conf.
Reviewed by: brooks
No objections on: net
work by yar, thompsa and myself. The checksum offloading part also involves
work done by Mihail Balikov.
The most important changes:
o Instead of global linked list of all vlan softc use a per-trunk
hash. The size of hash is dynamically adjusted, depending on
number of entries. This changes struct ifnet, replacing counter
of vlans with a pointer to trunk structure. This change is an
improvement for setups with big number of VLANs, several interfaces
and several CPUs. It is a small regression for a setup with a single
VLAN interface.
An alternative to dynamic hash is a per-trunk static array with
4096 entries, which is a compile time option - VLAN_ARRAY. In my
experiments the array is not an improvement, probably because such
a big trunk structure doesn't fit into CPU cache.
o Introduce an UMA zone for VLAN tags. Since drivers depend on it,
the zone is declared in kern_mbuf.c, not in optional vlan(4) driver.
This change is a big improvement for any setup utilizing vlan(4).
o Use rwlock(9) instead of mutex(9) for locking. We are the first
ones to do this! :)
o Some drivers can do hardware VLAN tagging + hardware checksum
offloading. Add an infrastructure for this. Whenever vlan(4) is
attached to a parent or parent configuration is changed, the flags
on vlan(4) interface are updated.
In collaboration with: yar, thompsa
In collaboration with: Mihail Balikov <mihail.balikov interbgc.com>
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
copy of Ethernet address.
- Change iso88025_ifattach() and fddi_ifattach() to accept MAC
address as an argument, similar to ether_ifattach(), to make
this work.
as it is done for usual promiscuous mode already. This info is important
because promiscuous mode in the hands of a malicious party can jeopardize
the whole network.
panics, which occur when stale ifnet pointers are left in struct
moptions hung off of inpcbs:
- Add in_ifdetach(), which matches in6_ifdetach(), and allows the
protocol to perform early tear-down on the interface early in
if_detach().
- Annotate that if_detach() needs careful consideration.
- Remove calls to in_pcbpurgeif0() in the handling of SIOCDIFADDR --
this is not the place to detect interface removal! This also
removes what is basically a nasty (and now unnecessary) hack.
- Invoke in_pcbpurgeif0() from in_ifdetach(), in both raw and UDP
IPv4 sockets.
It is now possible to run the msocket_ifnet_remove regression test
using HEAD without panicking.
MFC after: 3 days
