during a data phase. Before, we would try to recover the autosense, but
the DMA engine would still be active with interrupted transfer, and we'd
quickly spiral out of control and cause massive data corruption. For now,
just reset the chip and cancel everything. The better solution is to
cancel the DMA operation, but there is no clear way to do that right now.
The data corruption problem is severe enough to warrant this fix in the
interim. Thanks to Kris Kenneway to sacrificing countless filesystems to
this bug.
MFC After: 3 days
on boards with VIA gigE controllers that are embedded in VIA chipsets.
Presumably, they don't have an external EEPROM and store the MAC
address somewhere else. To get around this, force an autoload and
read the station address from the RX filter registers instead.
This has been tested to work on both embedded and standalone
controllers.
While there also check for failed device_add_child calls.
Found by: Coventry Analysis tool[1].
Submitted by: sam[1]
Approved by: pjd (mentor)
MFC after: 1 week
here on in, if_ndis.ko will be pre-built as a module, and can be built
into a static kernel (though it's not part of GENERIC). Drivers are
created using the new ndisgen(8) script, which uses ndiscvt(8) under
the covers, along with a few other tools. The result is a driver module
that can be kldloaded into the kernel.
A driver with foo.inf and foo.sys files will be converted into
foo_sys.ko (and foo_sys.o, for those who want/need to make static
kernels). This module contains all of the necessary info from the
.INF file and the driver binary image, converted into an ELF module.
You can kldload this module (or add it to /boot/loader.conf) to have
it loaded automatically. Any required firmware files can be bundled
into the module as well (or converted/loaded separately).
Also, add a workaround for a problem in NdisMSleep(). During system
bootstrap (cold == 1), msleep() always returns 0 without actually
sleeping. The Intel 2200BG driver uses NdisMSleep() to wait for
the NIC's firmware to come to life, and fails to load if NdisMSleep()
doesn't actually delay. As a workaround, if msleep() (and hence
ndis_thsuspend()) returns 0, use a hard DELAY() to sleep instead).
This is not really the right thing to do, but we can't really do much
else. At the very least, this makes the Intel driver happy.
There are probably other drivers that fail in this way during bootstrap.
Unfortunately, the only workaround for those is to avoid pre-loading
them and kldload them once the system is running instead.
16C950. Adding it here doesn't unlock any of the cool 16C950 features
(like the 128 byte fifo, the different prescalor, etc), but it does
seem to get it working for me in light testing.
Card Provided by: Ihsan Dogan
pumping data despite our scsi data counters being at 0, something has
gone massively wrong. The consequence of happily ignoring this is more
DMA phase errors and a disk full of spammed sectors. Instead, panic on
the first occurance to hopefully limit the damage.
MFC After: 3 days
latest 82550 and 82551 chipsets (revision IDs 0x0e, 0x0f and 0x10).
We were only enabling it for revisions 0x0c and 0x0d, now it's
enabled for any 8255x NIC with a revision ID bigger than 0x0c. It
should be safe, and this is what Intel does in their open source
driver.
MFC after: 2 weeks
Tested by: Pavel Lobach lobach_pavel at mail dot ru
This also removes the warning timeout on the taskqueues stalling as
I'm tired of getting ATA error reports for problems in other parts ;)
Misc cosmetic and comment cleanups now we are here.
number of task threads to start on boot. Go back to a default of 3
threads to work around lost battery state problems. Users that need
a setting of 1 can set this via the tunable. I am investigating the
underlying issues and this tunable can be removed once they are solved.
MFC after: 2 days
includes the MD header for us. Do not include <machine/specialreg.h>
as it is not a header file that can be included from MI files. It
is included from <machine/pmc_mdep.h> if so needed and possible.
Ok'd: jkoshy@
ioctls are now handled explicitly, but we can't really do anything
with them unless the NIC is up (trying to get/set a parameter when
the NDIS driver isn't running always yields an error). If something
invokes either of these ioctls and the NIC isn't initialized, punt
to the default ieee80211_ioctl() routine.
While we wait for holds to be released, print a list of who holds us
back once per second.
Use the new KPI from GEOM instead of vfs_mount.c calling g_waitidle().
Use the new KPI also from ata.
With ATAmkIII's newbusification, ata could narrowly miss the window
and ad0 would not exist when we tried to mount root.
dc0: MII without any PHY!
We have to enable the connection to the MII first. Doing so fixes the
problem cards without breaking the older, working cards.
Bad card provided by: deischen
- ncr53c9x.c:
1.108: Remove unreachable break after return and goto statements.
1.109: avoid strong words; use 'screw' instead
1.110: Fix some typos. From Tom Cosgrove via jmc@openbsd.
1.114: nuke trailing whitespace
1.107 was already merged, 1.112 and 1.113 are not relevant for FreeBSD.
1.111 is a functional change and will be merged later.
- ncr53c9xreg.h:
1.12: DMA, not dma nor Dma.
1.13: Fix some typos. From Tom Cosgrove via jmc@openbsd.
1.14: nuke trailing whitespace
- ncr53c9xvar.h:
1.43: Fix some typos. From Tom Cosgrove via jmc@openbsd.
1.44: Constify.
1.42 and 1.46 were already merged, 1.45 is not relevant for FreeBSD.
- Merge esp_sbus.c rev. 1.31 from NetBSD: nuke trailing whitespace.
Rev. 1.28 and 1.30 were already merged, 1.29 is not relevant for FreeBSD.
- Remove unused headers.
- Use BUS_PROBE_DEFAULT.
- Use __func__ instead of hardcoded function names in error messages.
- Correct some comments.
- Correct some function declarations to match their prototypes.
- Some style(9) fixes (don't use function calls in initializers; indentation).
- Zero the allocated structs to avoid problems with uninitialized members.
- Remove the ifdef'ed out SBus interrupt priority code and the hook for
ncr53c9x_reset(), remove the unused SBus interrupt priority member from
esp_softc. On FreeBSD setting the SBus interrupt priority is entirely done
in sbus(4) and the reset function isn't even really used in NetBSD.
- s,dma,DMA, in comments.
- Make the code fit in 80 columns.
this buffer anyway so the constraint that it had to be DMA capable only
caused pain when devices failed to aquire the memory. Use a regular
malloc instead with sndbuf_setup.
Approved by: tanimura (mentor)
- Split core DRM routines back into their own module, rather than using the
nasty templated system like before.
- Development-class R300 support in radeon driver (requires userland pieces, of
course).
- Mach64 driver (haven't tested in a while -- my mach64s no longer fit in the
testbox). Covers Rage Pros, Rage Mobility P/M, Rage XL, and some others.
- i915 driver files, which just need to get drm_drv.c fixed to allow attachment
to the drmsub device. Covers i830 through i915 integrated graphics.
- savage driver files, which should require minimal changes to work. Covers the
Savage3D, Savage IX/MX, Savage 4, ProSavage.
- Support for color and texture tiling and HyperZ features of Radeon.
Thanks to: scottl (much p4 handholding)
Jung-uk Kim (helpful prodding)
PR: [1] kern/76879, [2] kern/72548
Submitted by: [1] Alex, lesha at intercaf dot ru
[2] Shaun Jurrens, shaun at shamz dot net
This allows to attach to the children (ATA devices) even without a
driver being attached. This allows atapi-cam to do its work both
with and without the pure ATAPI driver being present.
ATA patches by /me
ATAPI-cam pathes by Thomas
printf's during a verbose boot is more intuitive (the BAR listings and
interrupt routing info now comes after the config header dump rather than
just before it).
Save a memory dereference in the ISR by passing this in directly.
Calling pps_capture is MP safe for all other operations on struct
pps_state, so there's no need to aquire the lock before we do this,
even from a fast ISR. Avoid dereferencing sc->ppbus until after
pps_capture is called as well. These actions reduce somewhat the
cache effects that cause variance in interrupt times. On an
especially slow test machine (300MHz Cyrix GXm), this reduces the
interrupt latency about about 10% (from 21us to 19us) and helps a
little with the variance (although most of the variance seems to be
caused by lots of interrupt masking).
This also happens fixes one or two of bde's style issues.
we start turning any of them back on again. This works around a bug in
some BIOSen that alias two different link devices for APIC vs ATPIC modes
onto the same physical hardware link.
Submitted by: njl
Tested by: Antoine Brodin antoine dot brodin at laposte dot net
pcib_route_interrupt interface. Since there's only one interrupt pin
in the CardBus form factor, everybody gets to share it. Implement
cbb_route_interrupt to return the interrupt we have.
Suggested by: bms
Otherwise, busses that implement the pcib interface that forget to
implement pcib_route_interrupt would return EIO, which the caller
interprets as 'use interrupt 6'. This is likely the cause of much of
the grief that we had when I enabled power modes for the cardbus
bridge, since the card needed to reroute the interrupt to it and it
was getting 6 which was d by the pccbb sanity checks.
3ware's 9xxx series controllers. This corresponds to
the 9.2 release (for FreeBSD 5.2.1) on the 3ware website.
Highlights of this release are:
1. The driver has been re-architected to use a "Common Layer"
(all tw_cl* files), which is a consolidation of all OS-independent
parts of the driver. The FreeBSD OS specific portions of the
driver go into an "OS Layer" (all tw_osl* files).
This re-architecture is to achieve better maintainability, consistency
of behavior across OS's, and better portability to new OS's (drivers
for new OS's can be written by just adding an OS Layer that's specific
to the OS, by complying to a "Common Layer Programming Interface" API.
2. The driver takes advantage of multiple processors.
3. The driver has a new firmware image bundled, the new features of which
include Online Capacity Expansion and multi-lun support, among others.
More details about 3ware's 9.2 release can be found here:
http://www.3ware.com/download/Escalade9000Series/9.2/9.2_Release_Notes_Web.pdf
Since the Common Layer is used across OS's, the FreeBSD specific include
path for header files (/sys/dev/twa) is not part of the #include pre-processor
directive in any of the source files. For being able to integrate twa into
the kernel despite this, Makefile.<arch> has been changed to add the include
path to CFLAGS.
Reviewed by: scottl
problems here, it became clear we were being too complex.
o Don't keep track of resources in two places
o Use resource_list_purge instead of rolling our own
o Just reassign the ownership of the resource, rather than freeing it
and reallocating it.
o Fix compile problems when sizeof(u_long) != sizeof(int)
this code:
o rid is stored in the resource, so don't bother keeping track of it here.
o Implement memory space
o Don't try to activate 'memory card' CFEs. This is type memory, as opposed
to the memory resource.
resource_list_find. Check to make sure that rle is not NULL and panic
if it is (but it appears that resource_list_add already panics, so I'm
not entirely sure it is necessary now).
Add a test to make sure we have a interrupt resource when we're
disabling it. This is also a cannot happen, but the extra care
shoudln't hurt.
Found by: Coventry tool via sam@
whether or not the receive pipe is stopped. This ensures that we
do not attempt to start the same transfer twice, and it allows
ucomstop() to skip the restarting of the read pipe if it was not
originally running, such as when called indirectly from ucomreadcb().
PR: kern/79420
MFC after: 1 day
layer, but with a twist.
The twist has to do with the fact that Microsoft supports structured
exception handling in kernel mode. On the i386 arch, exception handling
is implemented by hanging an exception registration list off the
Thread Environment Block (TEB), and the TEB is accessed via the %fs
register. The problem is, we use %fs as a pointer to the pcpu stucture,
which means any driver that tries to write through %fs:0 will overwrite
the curthread pointer and make a serious mess of things.
To get around this, Project Evil now creates a special entry in
the GDT on each processor. When we call into Windows code, a context
switch routine will fix up %fs so it points to our new descriptor,
which in turn points to a fake TEB. When the Windows code returns,
or calls out to an external routine, we swap %fs back again. Currently,
Project Evil makes use of GDT slot 7, which is all 0s by default.
I fully expect someone to jump up and say I can't do that, but I
couldn't find any code that makes use of this entry anywhere. Sadly,
this was the only method I could come up with that worked on both
UP and SMP. (Modifying the LDT works on UP, but becomes incredibly
complicated on SMP.) If necessary, the context switching stuff can
be yanked out while preserving the convention calling wrappers.
(Fortunately, it looks like Microsoft uses some special epilog/prolog
code on amd64 to implement exception handling, so the same nastiness
won't be necessary on that arch.)
The advantages are:
- Any driver that uses %fs as though it were a TEB pointer won't
clobber pcpu.
- All the __stdcall/__fastcall/__regparm stuff that's specific to
gcc goes away.
Also, while I'm here, switch NdisGetSystemUpTime() back to using
nanouptime() again. It turns out nanouptime() is way more accurate
than just using ticks(). On slower machines, the Atheros drivers
I tested seem to take a long time to associate due to the loss
in accuracy.
systems that boot with this value at the lowest setting. Change the
default boot config back to "leave frequency as BIOS set it". Also, fix
buglet where acpi_throttle wouldn't be used if p4tcc was present but
disabled by the user.
MFC after: 1 week
Affects to people WITH an AD1888 codec, the system will output to the port
labeled "speaker" instead of microphone. System will work the same in
multiple operating systems.
If people are currently using their systems with this codec they will need
to swap their output ports.
I have _not_ checked audio input or line input (basically, I have checked
nothing other than line-out).
I believe this is an appropriate change, it makes us consistent with
documentation, and other operating systems. Furthermore, this feature
(playing) is the vast majority of sound activities, so if this makes is
right for playback and wrong for recording... playback is more important,
and we can fix recoding in the future without worries of screwing people
again in the future (since we'll be "right" on the playback).
Submitted by: David Cross
instructs the driver to avoid using Keyboard Interface Test command.
This command causes problems with some non-compliant hardware, resulting
in machine being abruptly powered down early in the boot process.
Particularly it's known that HP ZV5000 and Compaq R3000Z notebooks
are affected by this problem.
Due to popularity of those models this patch is good MFC5.4 candidate.
PR: 67745
Submitted by: Jung-uk Kim jkim at niksun.com
MFC after: 1 days
- newbus plumbing. Each atapicam bus is a child off of a parent ata channel
bus. This is somewhat of a hack, but allows the ata core to be completely
free of atapicam knowledge.
- No more global lists of softc's and no more groping around in internal ata
structures on each command.
- Giant-free operation of the completion handler.
- Per-bus mutex for protecting the busy list and synchronizing detach.
- Lots of streamlining and dead code elimination, better adherence to the
CAM locking protocol.
This feature still requires that the appropriate atapi-* driver be present
for each atapi device that you want to talk to (i.e. atapi-cd for cdroms).
It does work both compiled into the kernel and as a loadable module.
Reviewed by: thomas, sos
critical_enter() and critical_exit() are now solely a mechanism for
deferring kernel preemptions. They no longer have any affect on
interrupts. This means that standalone critical sections are now very
cheap as they are simply unlocked integer increments and decrements for the
common case.
Spin mutexes now use a separate KPI implemented in MD code: spinlock_enter()
and spinlock_exit(). This KPI is responsible for providing whatever MD
guarantees are needed to ensure that a thread holding a spin lock won't
be preempted by any other code that will try to lock the same lock. For
now all archs continue to block interrupts in a "spinlock section" as they
did formerly in all critical sections. Note that I've also taken this
opportunity to push a few things into MD code rather than MI. For example,
critical_fork_exit() no longer exists. Instead, MD code ensures that new
threads have the correct state when they are created. Also, we no longer
try to fixup the idlethreads for APs in MI code. Instead, each arch sets
the initial curthread and adjusts the state of the idle thread it borrows
in order to perform the initial context switch.
This change is largely a big NOP, but the cleaner separation it provides
will allow for more efficient alternative locking schemes in other parts
of the kernel (bare critical sections rather than per-CPU spin mutexes
for per-CPU data for example).
Reviewed by: grehan, cognet, arch@, others
Tested on: i386, alpha, sparc64, powerpc, arm, possibly more
to see what features they may support before calling identify/probe/attach.
This is necessary because the ACPI 3.0 spec requires driver support be
advertised before running any methods. For now, the flags are as specified
in for the _PDC and _OSC methods but we can support private flags as needed.
Add an implementation of this for acpi_cpu. It checks all its children
(notably cpufreq drivers) and calls the _PDC method to report the results.
creating the /dev/dpti%d entry that the software expects. This is just
a band-aid until either someone (hopefully) rewrites the utilities, or all
asr/dpt cards in existance get blasted into the sun.
the type of object represented by the handle argument.
- Allow vm_mmap() to map device memory via cdev objects in addition to
vnodes and anonymous memory. Note that mmaping a cdev directly does not
currently perform any MAC checks like mapping a vnode does.
- Unbreak the DRM getbufs ioctl by having it call vm_mmap() directly on the
cdev the ioctl is acting on rather than trying to find a suitable vnode
to map from.
Reviewed by: alc, arch@
series of controllers. Areca provides a CLI and HTTP management tool for
FreeBSD/i386 and FreeBSD/amd64 on their website. Many thanks to Areca for
their support of FreeBSD. Thanks also to Mike Tansca and Sentex Communications
for donating hardware.
Obtained from: Erich Chen <erich at areca com tw>
an ap in 11g with protection enabled
o correct rate selection when operating in 11g with protection when no
packets have been sent yet (from John Bicket)
o track api change to get first descriptor and use it to collect the frame
length for calculating the state bin
o add more debugging and shuffle some existing debugging to give more info
o bump version to distinguish bug fixes
to the rate control module for tx complete processing; this enables
rate control algorithms to extract the packet length for xmits that
require multiple descriptors
o ATA is now fully newbus'd and split into modules.
This means that on a modern system you just load "atapci and ata"
to get the base support, and then one or more of the device
subdrivers "atadisk atapicd atapifd atapist ataraid".
All can be loaded/unloaded anytime, but for obvious reasons you
dont want to unload atadisk when you have mounted filesystems.
o The device identify part of the probe has been rewritten to fix
the problems with odd devices the old had, and to try to remove
so of the long delays some HW could provoke. Also probing is done
without the need for interrupts, making earlier probing possible.
o SATA devices can be hot inserted/removed and devices will be created/
removed in /dev accordingly.
NOTE: only supported on controllers that has this feature:
Promise and Silicon Image for now.
On other controllers the usual atacontrol detach/attach dance is
still needed.
o Support for "atomic" composite ATA requests used for RAID.
o ATA RAID support has been rewritten and and now supports these
metadata formats:
"Adaptec HostRAID"
"Highpoint V2 RocketRAID"
"Highpoint V3 RocketRAID"
"Intel MatrixRAID"
"Integrated Technology Express"
"LSILogic V2 MegaRAID"
"LSILogic V3 MegaRAID"
"Promise FastTrak"
"Silicon Image Medley"
"FreeBSD PseudoRAID"
o Update the ioctl API to match new RAID levels etc.
o Update atacontrol to know about the new RAID levels etc
NOTE: you need to recompile atacontrol with the new sys/ata.h,
make world will take care of that.
NOTE2: that rebuild is done differently from the old system as
the rebuild is now done piggybacked on read requests to the
array, so atacontrol simply starts a background "dd" to rebuild
the array.
o The reinit code has been worked over to be much more robust.
o The timeout code has been overhauled for races.
o Support of new chipsets.
o Lots of fixes for bugs found while doing the modulerization and
reviewing the old code.
Missing or changed features from current ATA:
o atapi-cd no longer has support for ATAPI changers. Todays its
much cheaper and alot faster to copy those CD images to disk
and serve them from there. Besides they dont seem to be made
anymore, maybe for that exact reason.
o ATA RAID can only read metadata from all the above metadata formats,
not write all of them (Promise and Highpoint V2 so far). This means
that arrays can be picked up from the BIOS, but they cannot be
created from FreeBSD. There is more to it than just the missing
write metadata support, those formats are not unique to a given
controller like Promise and Highpoint formats, instead they exist
for several types, and even worse, some controllers can have
different formats and its impossible to tell which one.
The outcome is that we cannot reliably create the metadata of those
formats and be sure the controller BIOS will understand it.
However write support is needed to update/fail/rebuild the arrays
properly so it sits fairly high on the TODO list.
o So far atapicam is not supported with these changes. When/if this
will change is up to the maintainer of atapi-cam so go there for
questions.
HW donated by: Webveveriet AS
HW donated by: Frode Nordahl
HW donated by: Yahoo!
HW donated by: Sentex
Patience by: Vife and my boys (and even the cats)
