We should not be leaking these interfaces to the outside world given
that it's much easier for third-party components to use the devel/atf
package from ports.
As a side-effect, we can also drop the ATF pkgconfig and aclocal files
from the base system. Nothing in the base system needs these, and it
was quite ugly to have to get them installed only so that a few ports
could build. The offending ports have been fixed to depend on
devel/atf explicitly.
Reviewed by: bapt
Makefiles are evaluated without building things. In a normal build,
the prerequisites would be built, and CC would be an actual thing. In
an INDEX build, though, they don't exists. Redirect stderr to get rid
of annoying messages, and assume that the compiler version is 0 if the
actual compiler can't tell us. Do this in preference to guessing based
on numbers because gcc410 might be 4.10, or 4.1.0 and without
carefully crafted special knowledge we differentiate between them
easily (also ming-gcc has no clues at all). Elsewhere, don't trust
the compiler version if it is 0.
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
this allows make -n to do tree walks as expected without
doing anything else (as intended).
Use prefix _sub. to help avoid conflict with any real target.
Reviewed by: imp
Targets thus marked are supposed to run even with -n.
As such they should not do anything except run the sub-make.
Use an intermediate target _* to associate with _SUBDIR and which
depends on installincludes etc so that we get the correct behavior with -n.
Reviewed by: marcel
This is not a comprehensive list, as the variables themselves are spread
out over multiple files, but it is a start.
Add a section to make.conf noting that variables may be set there that
affect ports builds, but refer to ports.7 and elsewhere for the actual
listing; any listing in make.conf.5 would likely become out of date
fairly quickly.
PR: docs/189199
Reviewed by: bdrewery (previous version)
Approved by: hrs (mentor)
src/sys and the rest of the tree for builds.
o eliminate including bsd.mkopts.mk for the moment in kern.opts.mk
o No need to include src.opts.mk at all anymore. The reasons for it
are now coverted in sys.mk and src.sys.mk.
and MK_LLDB=no, so set those explicitly (now that we can do
that). Simplify tests for these variables as well, since we know they
will always be defined regardless of the phase of the build.
with clang 3.3. Useful for test building -current on a -stable system
in individual directories. Potentially useful if we ever want to
support, say, gcc 4.8 or 4.9's new warnings when building with an
external toolchain (but such support not yet committed). Document
the bsd.compiler.mk interface.
install it as fmake. This defaults to no. This should be viewed as the
first step towards evental migration of this historic code to ports
and removal from the tree.
This driver supports the low and high precision models (9 and 11 bits) and
it will auto-detect the both variants.
The driver expose the temperature registers (actual temperature, shutdown
and hysteresys temperature) and also the configuration register.
It was tested on FDT systems: RPi, BBB and on non-FDT systems: AR71xx, with
both, hardware i2c controllers (when available) and gpioiic(4).
This provides a simple and cheap way for verifying the i2c bus on embedded
systems.
versions. With its movement to src.opts.mk, bsd.prog.mk was testing
COMPILER_TYPE without including the bsd.compiler.mk anymore. In the
source tree, this caused no problems, for reasons that aren't clear,
but does cause problems outside of the source tree. Allow
bsd.compiler.mk to be included multiple times safely, and always
include bsd.compiler.mk at the top of bsd.prog.mk. Resist the urge to
put it in bsd.init.mk, since that would reintroduce the implicit
include.
options, so move their processing there. This fixes issues with
Makefiles that define NO_MAN=t and only inlcude bsd.*.mk files. A few
ports fell into this category, and they should be fixed by this change.
Also, for now, disable the warning about NO_foo being deprecated. More
work is needed than anticipated before we can do that, so kill the
noise for now.
cards. LSI has been maintaining this driver outside of the FreeBSD
tree. It overlaps support of ThunderBolt and Invader cards that mfi(4)
supports. By default mfi(4) will attach to cards. If the tunable:
hw.mfi.mrsas_enable=1
is set then mfi(4) will not probe and attach to these newer cards and
allow mrsas(4) to attach. So by default this driver will not effect
a FreeBSD system unless mfi(4) is removed from the kernel or the
tunable is enabled.
mrsas(4) attaches disks to the CAM layer so it depends on CAM and devices
show up as /dev/daX. mfiutil(8) does not work with mrsas. The FreeBSD
version of MegaCli and StorCli from LSI do work with mrsas. It appears
that StorCli only works with mrsas. MegaCli appears to work with mfi(4)
and mrsas(4).
It would be good to add mfiutil(4) support to mrsas, emulations modes,
kernel logging, device aliases to ease the transition between mfi(4)
and mrsas(4).
Style issues should be resolved by LSI when they get committers approved.
The plan is get this driver in FreeBSD 9.3 to improve HW support.
Thanks to LSI for developing, testing and working with FreeBSD to
make this driver co-exist in FreeBSD. This improves the overall
support of MegaRAID SAS.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: scottl
MFC after: 3 days
Sponsored by: LSI
build world, so it is the only make we build or install. fmake is
still in the tree, but disconnected, and upgrades from older systems
that still have bmake has not been removed, but its state has not been
tested (it should work given how minimal the work to upgrade to bmake
is).
/etc/src.conf to this file as well. Now, it will only affect builds of
/usr/src and not others that use the bsd.*.mk files. Specifically
don't install src.opts.mk so we can catch when it 'leaks' into
bsd.*.mk again and have there be errors when this happens. Future
commits will move to including src.opts.mk instead of bsd.own.mk when
all that's needed is one of the MK_FOO options from src.opts.mk.
Future options should be placed here, unless they directly affect a
bsd.*.mk file, in which case they should be placed in bsd.opts.mk.
