on the AES-NI code, and modified as needed for use on ARMv8. When loaded
the driver will check the appropriate field in the id_aa64isar0_el1
register to see if AES is supported, and if so the probe function will
signal the driver should attach.
With this I have seen up to 2000Mb/s from the cryptotest test with a single
thread on a ThunderX Pass 2.0.
Reviewed by: imp
Obtained from: ABT Systems Ltd
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8297
We need to remove the line since we removed the related manual just now.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
A few months ago, we removed the driver, which was not necessary any longer.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
We enhanced the vmbus driver to support PCIe pass-through recently.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
VSS stands for "Volume Shadow Copy Service". Unlike virtual machine
snapshot, it only takes snapshot for the virtual disks, so both
filesystem and applications have to aware of it, and cooperate the
whole VSS process.
This driver exposes two device files to the userland:
/dev/hv_fsvss_dev
Normally userland programs should _not_ mess with this device file.
It is currently used by the hv_vss_daemon(8), which freezes and
thaws the filesystem. NOTE: currently only UFS is supported, if
the system mounts _any_ other filesystems, the hv_vss_daemon(8)
will veto the VSS process.
If hv_vss_daemon(8) was disabled, then this device file must be
opened, and proper ioctls must be issued to keep the VSS working.
/dev/hv_appvss_dev
Userland application can opened this device file to receive the
VSS freeze notification, hold the VSS for a while (mainly to flush
application data to filesystem), release the VSS process, and
receive the VSS thaw notification i.e. applications can run again.
The VSS will still work, even if this device file is not opened.
However, only filesystem consistency is promised, if this device
file is not opened or is not operated properly.
hv_vss_daemon(8) is started by devd(8) by default. It can be disabled
by editting /etc/devd/hyperv.conf.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Reviewed by: kib, mckusick
MFC after: 3 weeks
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8224
- Increase Rx buffer size from MCLBYTES to MJUMPAGESIZE.
- Provide an additional defragmentation routine for frames larger
than MCLBYTES; that is required by A-MSDU / Atheros Fast-Frames
support to work with current Tx path implementation.
Enabled features list for RTL8188CE:
- Atheros Fast-Frames;
- A-MPDU (Tx / Rx);
- A-MSDU (Tx / Rx; 4k only);
- Short Guard Interval.
Tested with:
- RTL8188CE (STA+AP) + RTL8821AU (STA).
- RTL8188CE (STA) + RTL8188CUS (AP).
Relnotes: yes
After removal of SMB_TRANS some information in the description of
SMB_BWRITE has become stale. E.g., the maximum block size has been
restored to 32.
Also, the descriptions of SMB_BREAD and SMB_BWRITE had some
incorrect information on the SMBus protocol details.
MFC after: 1 week
X-MFC with: r308242
Differential Revision: https://reviews.freebsd.org/D8431
This change reverts most of r281985.
The method did not map to anything defined by SMBus protocol and could
not be implemented for SMBus controllers.
This change is obviously not backwards compatible, but I have good
reasons to believe that there have never been any users of SMB_TRANS.
Discussed with: grembo, jhb
MFC after: 6 weeks
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
These two ALU instructions first appeared on Linux. Then, libpcap adopted
and made them available since 1.6.2. Now more platforms including NetBSD
have them in kernel. So do we.
--이 줄 이하는 자동으로 제거됩니다--
VFP code to store the old context, with lazy loading of the new context
when needed.
FPU_KERN_NOCTX is missing as this is unused in the crypto code this has
been tested with, and I am unsure on the requirements of the UEFI
Runtime Services.
Reviewed by: kib
Obtained from: ABT Systeems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8276
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
This commit, long overdue, contains contributions in the last 2 years
from Stefano Garzarella, Giuseppe Lettieri, Vincenzo Maffione, including:
+ fixes on monitor ports
+ the 'ptnet' virtual device driver, and ptnetmap backend, for
high speed virtual passthrough on VMs (bhyve fixes in an upcoming commit)
+ improved emulated netmap mode
+ more robust error handling
+ removal of stale code
+ various fixes to code and documentation (some mixup between RX and TX
parameters, and private and public variables)
We also include an additional tool, nmreplay, which is functionally
equivalent to tcpreplay but operating on netmap ports.
Ignore the ECN bits on 'tos' and 'set-tos' and allow to use
DCSP names instead of having to embed their TOS equivalents
as plain numbers.
Obtained from: OpenBSD
Sponsored by: OPNsense
Differential Revision: https://reviews.freebsd.org/D8165
- Add m_getclr(9) symlink to ObsoleteFiles.inc (removed in r295481).
- Add const qualifiers in m_dup(), m_dup_pkthdr() and m_tag_copy_chain()
(r286450).
- Fix m_dup_pkthdr() definition (it's not the same as m_move_pkthdr()).
MFC after: 5 days
The tag fastroute came from ipf and was removed in OpenBSD in 2011. The code
allows to skip the in pfil hooks and completely removes the out pfil invoke,
albeit looking up a route that the IP stack will likely find on its own.
The code between IPv4 and IPv6 is also inconsistent and marked as "XXX"
for years.
Submitted by: Franco Fichtner <franco@opnsense.org>
Differential Revision: https://reviews.freebsd.org/D8058
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
function from restarting the timer.
Commonly taskqueue_enqueue_timeout() is called from within the task
function itself without any checks for teardown. Then it can happen
the timer stays active after the return of taskqueue_drain_timeout(),
because the timeout and task is drained separately.
This patch factors out the teardown flag into the timeout task itself,
allowing existing code to stay as-is instead of applying a teardown
flag to each and every of the timeout task consumers.
Add assert to taskqueue_drain_timeout() which prevents parallel
execution on the same timeout task.
Update manual page documenting the return value of
taskqueue_enqueue_timeout().
Differential Revision: https://reviews.freebsd.org/D8012
Reviewed by: kib, trasz
MFC after: 1 week
db_segsize().
Use db_segsize() to set the default operand/address size for
disassembling. Allow overriding this with the "alternate" display
format /I. The API of db_disasm() should be debooleanized to pass a
more general request (amd64 needs overrides to sizes of 16, 32, and
64, but this commit doesn't implement anything for amd64 since much
larger changes are needed to restore the amd64 disassmbler's support
for non-default sizes).
Fix db_print_loc_and_inst() to ask for the normal format and not the
alternate in normal operation.
This is most useful for vm86 mode, but also works for 16-bit protected
mode.
Use db_segsize() to avoid trying to print a garbage stack trace if %cs
is 16 bits. Print something like the stack trace termination message
for a trap boundary instead.
Document that the alternate format is now useful on i386.
AMD chipsets have proprietary mechanisms for dicovering resources.
Those resources are not discoverable via plug-and-play mechanisms
like PCI configuration registers or ACPI.
For this reason a chipset-specific knowledge of proprietary registers
is required.
At present there are two FreeBSD drivers that require the proprietary
resource discovery. One is amdsbwd which is a driver for the watchdog
timer in the AMD chipsets. The other is intpm SMBus driver when it
attaches to the newer AMD chipsets where the resources of the SMBus HBA
are not described in the regular PCI way.
In both cases the resources are discovered by accessing AMD PMIO space.
Thus, many definitions are shared between the two drivers.
This change puts those defintions into a common header file.
As an added benefit, intpm driver now supports newest FCHs built into
AMD processors of Family 15h, models 70h-7Fh and Family 16h, models
30h-3Fh.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8004
Now that all of the necessary bits for ARMv6 support for CloudABI have
been checked in, let's hook the kernel module up to the build and
document its existence.
This is an RTL8168 chip, which we already support so all we have to do is add
the vendor ID.
PR: 212876
Submitted by: Tobias Kortkamp <t@tobik.me>
MFC after: 3 days
