o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
parent interface tasks to complete. This had been added to the ioctl path but
it is also need elsewhere like detach so its safe to teardown.
Reported by: Hans Petter Selasky
Submitted by: sam
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel
the net80211 layer has complete control over the handling of mgt frames
(in particular, the ac, tx rate, and retry count); this also allows us
to purge the M_LINK0 flag that was attached to mbufs to mark them as
needing encryption for shared key auth
o change ieee80211_send_setup to take a tid parameter so it can be used
to setup QoS frames
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
o add IEEE80211_F_JOIN flag to ieee80211_fix_rate to indicate a station
is joining a BSS; this is used to control whether or not we over-write
the basic rate bit in the calculated rate set
o fix ieee80211_fix_rate to honor IEEE80211_F_DODEL when IEEE80211_F_DONEGO
is not specified (e.g. when joining an ibss network)
o on sta join always delete unusable rates from the negotiated rate set,
this was being done only ibss networks but is also needed for 11g bss
with mixed stations
o on sta join delete unusable rates from the bss node's rate set, not the
scan table entry's rate set
o when calculating a rate set for new neighbors in an ibss caculate a
negotiated rate set so drivers are not presented with rates they should
not use
Submitted by: Sepherosa Ziehau (w/ modifications)
Obtained from: DragonFly
MFC after: 1 month
in the 802.11 layer: we send a directed probe request frame to the
current ap bmiss_max times (w/o answer) before scanning for a new ap.
MFC after: 2 weeks
add support for getting the current policy setting and collecting
the list of mac addresses in the acl table.
Submitted by: Michal Mertl (original version)
MFC after: 2 weeks
o add ic_curchan and use it uniformly for specifying the current
channel instead of overloading ic->ic_bss->ni_chan (or in some
drivers ic_ibss_chan)
o add ieee80211_scanparams structure to encapsulate scanning-related
state captured for rx frames
o move rx beacon+probe response frame handling into separate routines
o change beacon+probe response handling to treat the scan table
more like a scan cache--look for an existing entry before adding
a new one; this combined with ic_curchan use corrects handling of
stations that were previously found at a different channel
o move adhoc neighbor discovery by beacon+probe response frames to
a new ieee80211_add_neighbor routine
Reviewed by: avatar
Tested by: avatar, Michal Mertl
MFC after: 2 weeks
here but it includes completed 802.11g, WPA, 802.11i, 802.1x, WME/WMM,
AP-side power-save, crypto plugin framework, authenticator plugin framework,
and access control plugin frameowrk.
count handling of station entries in hostap mode:
Input path:
o driver is now expected to find the node associated with the
sender of a received frame; use ic_bss if none is located
o driver passes the (referenced) node into ieee80211_input for
use within the wlan module and is responsible for cleaning up
on return
o the antenna state is no longer passed up with each frame; this
is now considered driver-private state and drivers are responsible
for keeping it in the driver-private part of a node
Output path:
Revamp output path for management frames to eliminate redundant
locking that causes problems and to correct reference counting
bogosity that occurs when stations are timed out due to inactivity
(in AP mode). On output the refcnt'd node is stashed in the pkthdr's
recvif field (yech) and retrieved by the driver. This eliminates
an unref/ref scenario and related node table unlock/lock due to the
driver looking up the node. This is particularly important when
stations are timed out as this causes a lock order reversal that
can result in a deadlock. As a byproduct we also reduce the overhead
for sending management frames (minimal). Additional fallout from
this is a change to ieee80211_encap to return a refcn't node for
tieing to the outbound frame. Node refcnts are not reclaimed until
after a frame is completely processed (e.g. in the tx interrupt
handler). This is especially important for timed out stations as
this deref will be the final one causing the node entry to be
reclaimed.
Additional semi-related changes:
o replace m_copym use with m_copypacket (optimization)
o add assert to verify ic_bss is never free'd during normal operation
o add comments explaining calling conventions by drivers for frames
going in each direction
o remove extraneous code that "cannot be executed" (e.g. because
pointers may never be null)
override in their sub-class; this eliminates the hack of interpreting the
EINPROGRESS return value to mean "don't do any of the normal work"
o correct active scanning so the first channel is only scanned once and so
per-channel passive mode is properly honored
o expose 802.11 FSM state names so every driver doesn't keep a private copy
o eliminate node parameter to ieee80211_begin_scan; it was not being used
o code reorg (relative to old netbsd-derived code) for future growth
o drivers now specify available channels and rates and 802.11 layer handles
almost all ifmedia actions
o multi-mode support for 11a/b/g devices
o 11g protocol additions (incomplete)
o new element id additions (for other than 11g)
o node/station table redone for proper locking and to eliminate driver
incestuousness
o split device flags and capabilities to reduce confusion and provide room
for expansion
o incomplete power management infrastructure (need to revisit)
o incomplete hooks for software retry
o more...
