While we print failure messages on the console, sometimes logs are lost or
overwhelmed. Keeping a count of how many times we've failed retriable commands
helps get a magnitude of the problem.
Retried commands can indicate a performance degredation of an nvme drive. Keep
track of the number of retries and report it out via sysctl, just like number of
commands an interrupts.
Also convert it to a bool. While the rest of the driver isn't yet bool clean,
this will help.
Reviewed by: cem@
Differential Revision: https://reviews.freebsd.org/D20988
The nvme drive dumps only the most relevant details about a command when it
fails. However, there are times this is not sufficient (such as debugging weird
issues for a new drive with a vendor). Setting hw.nvme.verbose_cmd_dump=1
in loader.conf will enable more complete debugging information about each
command that fails.
Reviewed by: rpokala
Sponsored by: Netflix
Differential Version: https://reviews.freebsd.org/D20988
These macros make places where we extract these easier to read. The shift and
mask stuff is also a bit tedious and error prone. Start with the CAP_LO and
CAP_HI registers since their scope is somewhat constrained. This is style
chagne only, no functional changes.
Reviewed by: chuck
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20979
This affects the detection of 24-hour vs AM/PM mode... the ampm bit is in a
different location on 2127 and 2129 chips compared to other nxp rtc chips.
I noticed the 2127 case wasn't being handled correctly when I accidentally
misconfiged my system by claiming my PCF2129 was a 2127.
with various laptops using hdaa(4) sound devices. We don't seem to know
the "correct" configurations for these devices and the defaults are far
superiour, e.g. they work if you don't nuke the default configs.
PR: 200526
Differential Revision: https://reviews.freebsd.org/D17772
Neither the 1.3 or 1.4 standards say this number is 1's based, but adding 1
costs little and copes with those NVMe drives that report '0' in this field
cheaply. This is consistent with what the Linux driver does as well.
This fixes the following panic on powerpc:
pci_get_vendor failed for pcib1 on bus ofwbus0, error = 2
PR: 238730
Reported by: Dennis Clarke <dclarke@blastwave.org>
Tested by: Dennis Clarke <dclarke@blastwave.org>
MFC after: 2 weeks
on PCx2129 chips too.
The datasheet for the PCx2129 chips says that there is only a watchdog
timer, no countdown timer. It turns out the countdown timer hardware is
there and works just the same as it does on a PCx2127 chip, except that you
can't use it to trigger an interrupt or toggle an output pin. We don't need
interrupts or output pins, we only need to read the timer register to get
sub-second resolution. So start treating the 2129 chips the same as 2127.
An obscure footnote in the datasheets for the PCx2127, PCx2129, and
PCF8523 rtc chips states that the chips do not support i2c repeat-start
operations. When the driver was originally written and tested, the i2c
bus on that system also didn't support repeat-start and just quietly
turned repeat-start operations into a stop-then-start, making it appear
that the nxprtc driver was working properly.
The repeat-start situation only comes up on reads, so instead of using
the standard iicdev_readfrom(), use a local nxprtc_readfrom(), which is
just a cut-and-pasted copy of iicdev_readfrom(), modified to send two
separate start-data-stop sequences instead of using repeat-start.
The driver used to log any non-zero cause and when running with a single
line interrupt it would spam the console/logs with reports of interrupts
that are of no interest to anyone.
MFC after: 1 week
Sponsored by: Chelsio Communications
Enable this for the NovAtel OEMv2 GPS receiver.
Not fixed: The receiver shows up as "<Interface 0>" in the device
tree, because that is literally what the descriptor-string is.
Reviewed by: hselasky@
When a command is finished running, we must transition it from INQUEUE
to busy state. We were failing to do that, so we hit a panic when the
commands were freed. This only affects mpr, mps already did simmilar
things. Now both the polling and interrupt paths properly set BUSY as
appropriate.
This device cannot cross a 4GB boundary with DMA. Removing the
boundary in r346386 resulted in low frequency memory corruption on
machines with isci(4) controllers.
Submitted by: gallatin@
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20910
Add VMBus protocol version 4.0. and 5.0 to support Windows 10 and newer HyperV hosts.
For VMBus 4.0 and newer HyperV, the netvsc gpadl teardown must be done after vmbus close.
Submitted by: whu
MFC after: 2 weeks
Sponsored by: Microsoft
r348164 added code to iicbus_request_bus/iicbus_release_bus to automatically
call device_busy()/device_unbusy() as part of aquiring exclusive use of the
bus (so modules can't be unloaded while the bus is exclusively owned and/or
IO is in progress). That broke the ability to do i2c IO from a slave device
probe method, because the slave isn't attached yet, so calling device_busy()
triggers a sanity-check panic for trying to busy a non-attached device.
Now we check whether the device status is < DS_ATTACHING, and if so we busy
the iicbus rather than the slave device. I think this leaves a small window
where a module could be unloaded while probing is in progress. But I think
that's true of all devices, and probably should be fixed by introducing a
DS_PROBING state for devices, and handling that at various points in the
newbus code.
Eliminate the TIMEDOUT state. This state really conveyed two different
concepts: I timed out during recovery (and my command got put on the
recovery queue), and I timed out diring discovery (which doesn't).
Separate those two concepts into two flags. Use the TIMEDOUT flag to
fail requests as timed out. Use the on queue flag to remove them from
the queue.
In mps_intr_locked for MPI2_RPY_DESCRIPT_FLAGS_ADDRESS_REPLY message
type, when completing commands, ignore the ones that are not in state
INQUEUE. They were already completed as part of the recovery
process. When we complete them twice, we wind up with entries on the
free queue that are marked as busy, trigging asserts.
Reviewed by: scottl (earlier version, just for mpr)
Differential Revision: https://reviews.freebsd.org/D20785
The hold_count and wire_count fields of struct vm_page are separate
reference counters with similar semantics. The remaining essential
differences are that holds are not counted as a reference with respect
to LRU, and holds have an implicit free-on-last unhold semantic whereas
vm_page_unwire() callers must explicitly determine whether to free the
page once the last reference to the page is released.
This change removes the KPIs which directly manipulate hold_count.
Functions such as vm_fault_quick_hold_pages() now return wired pages
instead. Since r328977 the overhead of maintaining LRU for wired pages
is lower, and in many cases vm_fault_quick_hold_pages() callers would
swap holds for wirings on the returned pages anyway, so with this change
we remove a number of page lock acquisitions.
No functional change is intended. __FreeBSD_version is bumped.
Reviewed by: alc, kib
Discussed with: jeff
Discussed with: jhb, np (cxgbe)
Tested by: pho (previous version)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D19247
table VCTRL registers.
Unconditionally program the MSI-X vector control Mask field for MSI-X
table entries without regarud for Mask's previous value. Some devices
return all zeros on reads of the VCTRL registers, which would cause us
to skip disabling interrupts. This fixes the Samsung SM961/PM961 SSDs
which are return zero starting from offset 0x3084 within the memory
region specified by BAR0, even when they are active MSI-X vectors.
The Illumos kernel writes these unconditionally to 0 or 1. However,
section 6.8.2.9 of the PCI Local Bus 3.0 spec (dated Feb 3, 2004)
states for bits 31::01:
After reset, the state of these bits must be 0. However, for
potential future use, software must preserve the value of
these reserved bits when modifying the value of other Vector
Control bits. If software modifies the value of these reserved
bits, the result is undefined."
so we always set or clear the Mask bit, but otherwise preserves the
old value.
PR: https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=211713
Reviewed By: imp, jhb
Submitted by: Ka Ho Ng
MFC After: 1 week
Differential Revision: https://reviews.freebsd.org/D20873
While at it fix an invalid memory access issue when attaching external
USB HUBs, which are not mapped by ACPI, due to missing status check
when calling AcpiGetObjectInfo() from acpi_usb_hub_port_probe_cb().
Sponsored by: Mellanox Technologies
When the system has no graphical console, such as bhyve in common
configurations, ignore kern.vt.splash_cpu, instead of panicking
on INVARIANTS kernels.
Reviewed by: cem dumbbell
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20877
Print the adapter name rather than the address of the adapter
to avoid kernel address leakage.
PR: Bug 238642
Submitted by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed by: vmaffione
MFC after: 1 week
All MMCBR bridges have to implement all the MMCBR variables. This
implements them for everybody that currently doesn't.
A common routine for this should be written.
XCHAN_CAP_BOUNCE.
The only application that uses bounce buffering for now is the Government
Furnished Equipment (GFE) P2's dma core (AXIDMA) with its own dedicated
cacheless bounce buffer.
Sponsored by: DARPA, AFRL
Otherwise there is a window where they may be rescheduled. This
typically manifested as a page fault shortly after unloading if_iwm.ko.
Close the race by draining callouts after calling iwm_stop_device(),
which is also what Dragonfly does.
Change whitespace to reduce gratuitous diffs with Dragonfly.
Reported and tested by: seanc
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Previously the TOE code used its own custom unmapped mbufs via
EXT_FLAG_VENDOR1. The old version always wired the entire AIO request
buffer first for the duration of the AIO operation and constructed
multiple mbufs which used the wired buffer as an external buffer.
The new version determines how much room is available in the socket
buffer and only wires the pages needed for the available room building
chains of M_NOMAP mbufs. This means that a large AIO write will now
limit the amount of wired memory it uses to the size of the socket
buffer.
Reviewed by: gallatin, np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D20839
that node is also compatible with syscon. For instance,
Rockchip RK3399's GRF (General Register Files) is compatible
with simple-mfd as well as syscon and has devices like
usb2-phy, emmc-phy and pcie-phy etc. under it.
Reviewed by: manu
This patch is the driver for NTB hardware in AMD SoCs (ported from Linux)
and enables the NTB infrastructure like Doorbells, Scratchpads and Memory
window in AMD SoC. This driver has been validated using ntb_transport and
if_ntb driver already available in FreeBSD.
Submitted by: Rajesh Kumar <rajesh1.kumar@amd.com>
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D18774
otherwise we panic.
dwmmc don't handle VCCQ (voltage for the IO line of the SD/eMMC) or
TIMING.
Add the needed accessor in the {read,write}_ivar functions.
Reviewed by: imp (previous version)
This patch fixes 2 panics. The first one is due to the current VNET not
being set in the emulated adapter transmission path. The second one
is caused by the M_PKTHDR flag not being set when preallocated mbufs
are recycled in the transmit path.
Submitted by: aleksandr.fedorov@itglobal.com
Reviewed by: vmaffione
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20824
The goal of this driver is consolidate information about SuperIO chips
and to provide for peaceful coexistence of drivers that need to access
SuperIO configuration registers.
While SuperIO chips can host various functions most of them are
discoverable and accessible without any knowledge of the SuperIO.
Examples are: keyboard and mouse controllers, UARTs, floppy disk
controllers. SuperIO-s also provide non-standard functions such as
GPIO, watchdog timers and hardware monitoring. Such functions do
require drivers with a knowledge of a specific SuperIO.
At this time the driver supports a number of ITE and Nuvoton (fka
Winbond) SuperIO chips.
There is a single driver for all devices. So, I have not done the usual
split between the hardware driver and the bus functionality. Although,
superio does act as a bus for devices that represent known non-standard
functions of a SuperIO chip. The bus provides enumeration of child
devices based on the hardcoded knowledge of such functions. The
knowledge as extracted from datasheets and other drivers.
As there is a single driver, I have not defined a kobj interface for it.
So, its interface is currently made of simple functions.
I think that we can the flexibility (and complications) when we actually
need it.
I am planning to convert nctgpio and wbwd to superio bus very soon.
Also, I am working on itwd driver (watchdog in ITE SuperIO-s).
Additionally, there is ithwm driver based on the reverted sensors
import, but I am not sure how to integrate it given that we still lack
any sensors interface.
Discussed with: imp, jhb
MFC after: 7 weeks
Differential Revision: https://reviews.freebsd.org/D8175
That is, instead of the current GPIO00 - GPIO15 the names will be GPIO00
- GPIO07, GPIO10 - GPIO17. The first digit is a GPIO "bank" / group
number and the second one is a pin number within the bank. Alternative
view is that the pin names are changed from decimal numbering scheme to
octal one (as there are 8 pins per bank).
Discussed with: cem, gonzo
MFC after: 2 weeks
With more ports, some of the registers are shifted a bit to accommodate.
This switch also adds two high speed Serdes/SGMII interfaces (2.5 Gb/s).
Sponsored by: Rubicon Communications, LLC (Netgate)
Since cxgbe(4) uses sglist instead of bus_dma, this required updates
to the code that generates scatter/gather lists for packets. Also,
unmapped mbufs are always sent via DMA and never as immediate data in
the payload of a work request.
Submitted by: gallatin (earlier version)
Reviewed by: gallatin, hselasky, rrs
Discussed with: np
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20616
address before returning it to the user. Some of the least significant
bits have special meaning and should be masked away.
Discussed with: kib@
MFC after: 3 days
Sponsored by: Mellanox Technologies
handle_ddp_close.
This eliminates a bad race where an aio_ddp_requeue that happened to run
after handle_ddp_close could bump up the active count.
Discussed with: jhb@
MFC after: 3 days
Sponsored by: Chelsio Communications
t_maxseg was changed in r293284 to not have any adjustment for TCP
timestamps. t4_tom inadvertently went back to pre-r293284 semantics
in r332506.
Sponsored by: Chelsio Communications
This fixes (userspace) console on the Marvell MACCHIATObin in ACPI mode with
latest TianoCore EDK2 firmware.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: mw, bcran
Differential Revision: https://reviews.freebsd.org/D20765
Previously, the aiotx task relied on the aio jobs in the queue to hold
a reference on the socket. However, when the last job is completed,
there is nothing left to hold a reference to the socket buffer lock
used to check if the queue is empty. In addition, if the last job on
the queue is cancelled, the task can run with no queued jobs holding a
reference to the socket buffer lock the task uses to notice the queue
is empty.
Fix these races by holding an explicit reference on the socket when
the task is queued and dropping that reference when the task
completes.
Reviewed by: np
MFC after: 1 week
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D20539
The format to use depends on hardware configuration (synthesis-time),
so make it compile-time kernel option.
Extended format allows DMA engine to operate with 64-bit memory addresses.
Sponsored by: DARPA, AFRL
"pin_list" allows to specify child pins as a list of pin numbers.
Existing hint "pins" serves the same purpose but with a 32-bit wide bit
mask. One problem with that is that a controller can have more than 32
pins. One example is amdgpio. Also, a list of numbers is a little bit
more human friendly than a matching bit mask. As a side note, it seems
that in FDT pins are typically specified by their numbers as well.
This commit also adds accessors for instance variables (IVARs) that
define the child pins. My primary goal is to allow a child to be
configured programmatically rather than via hints (assuming that FDT is
not supported on a platform). Also, while a child should not care about
specific pin numbers that are allocated to it, it could be interested in
how many were actually assigned to it.
While there, I removed "flags" instance variable. It was unused.
Reviewed by: mizhka
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20459
Use it to indicate whether the page may be safely freed following
its removal from the object. Also change vm_page_remove() to assume
that the page's object pointer is non-NULL, and have callers perform
this check instead.
This is a step towards an implementation of an atomic reference counter
for each physical page structure.
Reviewed by: alc, dougm, kib
MFC after: 1 week
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20758
"fdt" is removed from the driver module name as the driver does not
require FDT and can work very well on hints based systems.
A module dependency is added for gpiobus. Without that owc cannot
resolve symbols in gpiobus if both are loaded as kernel modules.
Finally, a driver module module version is added.
Reviewed by: imp
MFC after: 11 days
NANDFS has been broken for years. Remove it. The NAND drivers that
remain are for ancient parts that are no longer relevant. They are
polled, have terrible performance and just for ancient arm
hardware. NAND parts have evolved significantly from this early work
and little to none of it would be relevant should someone need to
update to support raw nand. This code has been off by default for
years and has violated the vnode protocol leading to panics since it
was committed.
Numerous posts to arch@ and other locations have found no actual users
for this software.
Relnotes: Yes
No Objection From: arch@
Differential Revision: https://reviews.freebsd.org/D20745
Since SES specs do not define mechanism to map enclosure slots to SATA
disks, AHCI EM code I written many years ago appeared quite useless,
that always bugged me. I was thinking whether it was a good idea, but
if LSI HBAs do that, why I shouldn't?
This change introduces simple non-standard mechanism for the mapping
into both AHCI EM and SES code, that makes AHCI EM on capable controllers
(most of Intel's) a first-class SES citizen, allowing it to report disk
physical path to GEOM, show devices inserted into each enclosure slot in
`sesutil map` and `getencstat`, control locate and fault LEDs for specific
devices with `sesutil locate adaX on` and `sesutil fault adaX on`, etc.
I've successfully tested this on Supermicro X10DRH-i motherboard connected
with sideband cable of its S-SATA Mini-SAS connector to SAS815TQ backplane.
It can indicate with LEDs Locate, Fault and Rebuild/Remap SES statuses for
each disk identical to real SES of Supermicro SAS2 backplanes.
MFC after: 2 weeks
Until r349278, bhyve presented a seg_max to the guest that was too large.
Detect this case and clamp it to the virtqueue size. Otherwise, we would
fail the "too many segments to enqueue" assertion in virtqueue_enqueue().
I hit this by running a guest with a MAXPHYS of 256 KB.
Reviewed by: bryanv cem
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20703
Previously nandsim_chip_status returned EINVAL iff both of user-provided
chip->ctrl_num and chip->num were out of bounds. If only one failed the
bounds check arbitrary memory would be read and returned.
The NAND framework is not built by default, nandsim is not intended for
production use (it is a simulator), and the nandsim device has root-only
permissions.
admbugs: 827
Reported by: Daniel Hodson of elttam
MFC after: 3 days
Security: kernel information leak or DoS
Sponsored by: The FreeBSD Foundation
In r349154, random device reads of size < 16 bytes (AES block size) were
accidentally broken to loop forever. Correct the loop condition for small
reads.
Reported by: pho
Reviewed by: delphij
Approved by: secteam(delphij)
Differential Revision: https://reviews.freebsd.org/D20686
This adds ACPI device path on devinfo(8) output and
show value of _UPC(usb port capabilities), _PLD (physical location of device)
when hw.usb.debug >= 1 .
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D20630
Add experimental feature to increase concurrency in Fortuna. As this
diverges slightly from canonical Fortuna, and due to the security
sensitivity of random(4), it is off by default. To enable it, set the
tunable kern.random.fortuna.concurrent_read="1". The rest of this commit
message describes the behavior when enabled.
Readers continue to update shared Fortuna state under global mutex, as they
do in the status quo implementation of the algorithm, but shift the actual
PRF generation out from under the global lock. This massively reduces the
CPU time readers spend holding the global lock, allowing for increased
concurrency on SMP systems and less bullying of the harvestq kthread.
It is somewhat of a deviation from FS&K. I think the primary difference is
that the specific sequence of AES keys will differ if READ_RANDOM_UIO is
accessed concurrently (as the 2nd thread to take the mutex will no longer
receive a key derived from rekeying the first thread). However, I believe
the goals of rekeying AES are maintained: trivially, we continue to rekey
every 1MB for the statistical property; and each consumer gets a
forward-secret, independent AES key for their PRF.
Since Chacha doesn't need to rekey for sequences of any length, this change
makes no difference to the sequence of Chacha keys and PRF generated when
Chacha is used in place of AES.
On a GENERIC 4-thread VM (so, INVARIANTS/WITNESS, numbers not necessarily
representative), 3x concurrent AES performance jumped from ~55 MiB/s per
thread to ~197 MB/s per thread. Concurrent Chacha20 at 3 threads went from
roughly ~113 MB/s per thread to ~430 MB/s per thread.
Prior to this change, the system was extremely unresponsive with 3-4
concurrent random readers; each thread had high variance in latency and
throughput, depending on who got lucky and won the lock. "rand_harvestq"
thread CPU use was high (double digits), seemingly due to spinning on the
global lock.
After the change, concurrent random readers and the system in general are
much more responsive, and rand_harvestq CPU use dropped to basically zero.
Tests are added to the devrandom suite to ensure the uint128_add64 primitive
utilized by unlocked read functions to specification.
Reviewed by: markm
Approved by: secteam(delphij)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D20313
rename the source to gsb_crc32.c.
This is a prerequisite of unifying kernel zlib instances.
PR: 229763
Submitted by: Yoshihiro Ota <ota at j.email.ne.jp>
Differential Revision: https://reviews.freebsd.org/D20193
names. I.e., everything related to pwm now goes in /dev/pwm. This will
make it easier for userland tools to turn an unqualified name into a fully
qualified pathname, whether it's the base pwmcX.Y name or a label name.
At a basic level, remove assumptions about the underlying algorithm (such as
output block size and reseeding requirements) from the algorithm-independent
logic in randomdev.c. Chacha20 does not have many of the restrictions that
AES-ICM does as a PRF (Pseudo-Random Function), because it has a cipher
block size of 512 bits. The motivation is that by generalizing the API,
Chacha is not penalized by the limitations of AES.
In READ_RANDOM_UIO, first attempt to NOWAIT allocate a large enough buffer
for the entire user request, or the maximal input we'll accept between
signal checking, whichever is smaller. The idea is that the implementation
of any randomdev algorithm is then free to divide up large requests in
whatever fashion it sees fit.
As part of this, two responsibilities from the "algorithm-generic" randomdev
code are pushed down into the Fortuna ra_read implementation (and any other
future or out-of-tree ra_read implementations):
1. If an algorithm needs to rekey every N bytes, it is responsible for
handling that in ra_read(). (I.e., Fortuna's 1MB rekey interval for AES
block generation.)
2. If an algorithm uses a block cipher that doesn't tolerate partial-block
requests (again, e.g., AES), it is also responsible for handling that in
ra_read().
Several APIs are changed from u_int buffer length to the more canonical
size_t. Several APIs are changed from taking a blockcount to a bytecount,
to permit PRFs like Chacha20 to directly generate quantities of output that
are not multiples of RANDOM_BLOCKSIZE (AES block size).
The Fortuna algorithm is changed to NOT rekey every 1MiB when in Chacha20
mode (kern.random.use_chacha20_cipher="1"). This is explicitly supported by
the math in FS&K §9.4 (Ferguson, Schneier, and Kohno; "Cryptography
Engineering"), as well as by their conclusion: "If we had a block cipher
with a 256-bit [or greater] block size, then the collisions would not
have been an issue at all."
For now, continue to break up reads into PAGE_SIZE chunks, as they were
before. So, no functional change, mostly.
Reviewed by: markm
Approved by: secteam(delphij)
Differential Revision: https://reviews.freebsd.org/D20312
Add some basic regression tests to verify behavior of both uint128
implementations at typical boundary conditions, to run on all architectures.
Test uint128 increment behavior of Chacha in keystream mode, as used by
'kern.random.use_chacha20_cipher=1' (r344913) to verify assumptions at edge
cases. These assumptions are critical to the safety of using Chacha as a
PRF in Fortuna (as implemented).
(Chacha's use in arc4random is safe regardless of these tests, as it is
limited to far less than 4 billion blocks of output in that API.)
Reviewed by: markm
Approved by: secteam(gordon)
Differential Revision: https://reviews.freebsd.org/D20392
Previously, there was a pwmc instance for each instance of pwm hardware
regardless of how many pwm channels that hardware supported. Now there
will be a pwmc instance for each channel when the hardware supports
multiple channels. With a separate instance for each channel, we can have
"named channels" in userland by making devfs alias entries in /dev/pwm.
These changes add support for ivars to pwmbus, and use an ivar to track the
channel number for each child. It also adds support for hinted children.
In pwmc, the driver checks for a label hint, and if present, it's used to
create an alias for the cdev in /dev/pwm. It's not anticipated that hints
will be heavily used, but it's easy to do and allows quick ad-hoc creation
of named channels from userland by using kenv to create hint.pwmc.N.label=
hints. Upcoming changes will add FDT support, and most labels will
probably be specified that way.
is nothing left in the file that related to pwmbus at all. It just contains
prototypes for the functions implemented in dev/pwm.ofw_pwm.c, so name it
accordingly and fix the include protect wrappers to match.
A new pwmbus.h will be coming along in a future commit.
The pwm and pwmbus interfaces were nearly identical, this merges them into a
single pwmbus interface. The pwmbus driver now implements the pwmbus
interface by simply passing all calls through to its parent (the hardware
driver). The channel_count method moves from pwm to pwmbus, and the
get_bus method is deleted (just no longer needed).
The net effect is that the interface for doing pwm stuff is now the same
regardless of whether you're a child of pwmbus, or some random driver
elsewhere in the hierarchy that is bypassing the pwmbus layer and is talking
directly to the hardware driver via cross-hierarchy connections established
using fdt data.
The pwmc driver is now a child of pwmbus, instead of being its sibling
(that's why the get_bus method is no longer needed; pwmc now gets the
device_t of the bus using device_get_parent()).
ioctl definitions and related datatypes that allow userland control of pwm
hardware via the pwmc device. The new name and location better reflects its
assocation with a single device driver.
part of ciss_detach. It's a left-over debug that isn't needed and also
discloses a kernel address. Only root could provoke as part of a
devctl or kldunload.
Submitted by: Fuqian Huang
MFC After: 1 week
asserted. Some development boards for example will reset on DTR,
and some radio interfaces will transmit on RTS.
This patch allows "stty -f /dev/ttyu9.init -rtsdtr" to prevent
RTS and DTR from being asserted on open(), allowing these devices
to be used without problems.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D20031
between each byte either sent or received). However, most transitions
actually complete in 2-3 microseconds.
By polling the status register with a delay of 4us with exponential
backoff, the performance of most IPMI operations is significantly
improved:
- A BMC update on a Supermicro x9 or x11 motherboard goes from ~1 hour
to ~6-8 minutes.
- An ipmitool sensor list time improves by a factor of 4.
Testing showed no significant improvements on a modern server by using
a lower delay.
The changes should also generally reduce the total amount of CPU or
I/O bandwidth used for a given IPMI operation.
Submitted by: Loic Prylli <lprylli@netflix.com>
Reviewed by: jhb
MFC after: 2 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20527
detection pins to the Marvell Xenon SDHCI controller.
These features are enable by 'vqmmc-supply' and 'cd-gpios' properties in the
DTS.
This fixes the SD Card detection on espressobin.
Sponsored by: Rubicon Communications, LLC (Netgate)
Enable synaptics and elantech touchpads, as well as IBM/Lenovo TrackPoints
by default, instead of having users find and toggle a loader tunable.
This makes things like two finger scroll and other modern features work out
of the box with X. By enabling these settings by default, we get a better
desktop experience in X, since xserver and evdev can make use of the more
advanced synaptics and elantech features.
Reviewed by: imp, wulf, 0mp
Approved by: imp
Sponsored by: B3 Init (zeising)
Differential Revision: https://reviews.freebsd.org/D20507
Add strict checks for unused bit states in Elantech trackpoint packet
parser to filter out spurious events produces by some hardware which
are detected as trackpoint packets. See comment on r328191 for example.
Tested by: Andrey Kosachenko <andrey.kosachenko@gmail.com>
Sign bits for X and Y motion data were taken from wrong places.
PR: 238291
Reported by: Andrey Kosachenko <andrey.kosachenko@gmail.com>
Tested by: Andrey Kosachenko <andrey.kosachenko@gmail.com>
MFC after: 2 weeks
Add a CAM-Newbus SDIO support module. This works provides a newbus
infrastructure for device drivers wanting to use SDIO. On the lower end
while it is connected by newbus to SDHCI, it talks CAM using the MMCCAM
framework to get to it.
This also duplicates the usbdevs framework to equally create sdiodev
header files with #defines for "vendors" and "products".
Submitted by: kibab (initial work, see https://reviews.freebsd.org/D12467)
Reviewed by: kibab, imp (comments on earlier version)
MFC after: 6 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19749
Currently slot_printf() uses two printf() calls to print the
device-slot name, and actual message. When other printf()s are
ongoing in parallel this can lead to interleaved message on the console,
which is especially unhelpful for debugging or error messages.
Take a hit on the stack and vsnprintf() the message to the buffer.
This way it can be printed along with the device-slot name in one go
avoiding console gibberish.
Reviewed by: marius
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19747
Add cam_sim_alloc_dev() as a wrapper to cam_sim_alloc() which takes
a device_t instead of the unit_number (which we can derive from the
dev again).
Add device_t sim_dev to struct cam_sim. It will be used to pass through
the bus for cases when both sides of CAM speak newbus already and we want
to link them (yet make the calls through CAM for now).
SDIO will be the first consumer of this. For that make use of
cam_sim_alloc_dev() in sdhci under MMCCAM.
This will also allow people to start iterating more on the idea
to newbus-ify CAM without changing 50+ device drivers from the start.
Also to be clear there are callers to cam_sim_alloc() which do not
have a device_t (e.g., XPT) or provide their own unit number so we cannot
simply switch the KPI entirely.
Submitted by: kibab (original idea, see https://reviews.freebsd.org/D12467)
Reviewed by: imp, chuck
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19746
Differentiate between PCI Express Endpoint devices and Root Complex
Integrated Endpoints in the nda driver. The Link Status and Capability
registers are not valid for Integrated Endpoints and should not be
displayed. The bhyve emulated NVMe device will advertise as being an
Integrated Endpoint.
Reviewed by: imp
Approved byL imp (mentor)
Differential Revision: https://reviews.freebsd.org/D20282
These calls are not the same in general: the former will dequeue the
page if it is enqueued, while the latter will just leave it alone. But,
all existing uses of the former apply to unmanaged pages, which are
never enqueued in the first place. No functional change intended.
Reviewed by: kib
MFC after: 1 week
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20470
This fixes a panic in Espressobin when gpioregulator fails to allocate the
GPIO pin (the GPIO controller is not there).
Sponsored by: Rubicon Communications, LLC (Netgate)
Provide the acpi handle path as the location string for the nvdimm
children of the nvdimm_root device.
Reviewed by: kib
Approved by: jhb (mentor)
MFC after: 1 week
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D20528
Prior to this commit, if PCIEM_SLOT_STA_ABP and PCIEM_SLOT_STA_PDC are
asserted simultaneously, FreeBSD sets a 5 second "hardware going away" timer
and then processes the "presence detect" change. In the (physically
challenging) case that someone presses the "attention button" and inserts
a new PCIe device at exactly the same moment, this results in FreeBSD
recognizing that the device is present, attaching it, and then detaching it
5 seconds later.
On EC2 "bare metal" hardware this is the precise sequence of events which
takes place when a new EBS volume is attached; virtual machines have no
difficulty effecting physically implausible simultaneity.
This patch changes the handling of PCIEM_SLOT_STA_ABP to only detach a
device if the presence of a device was detected *before* the interrupt
which reports the Attention Button push.
Reported by: Matt Wilson
Reviewed by: jhb
MFC after: 1 week
Sponsored by: https://www.patreon.com/cperciva
Differential Revision: https://reviews.freebsd.org/D20499
if a USB transfer is cancelled that we need to fake a completion event.
Implement missing support in ugen_fs_copy_out() to handle this.
This fixes issues with webcamd(8) and firefox.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Register MODULE_PNP_INFO for virtio devices using the newbus PNP information
provided by the previous commit. Matching can be quite simple; existing
probe routines only matched on bus (implicit) and device_type. The same
matching criteria are retained exactly, but is now also available to
devmatch(8).
Reviewed by: bryanv, markj; imp (earlier version)
Differential Revision: https://reviews.freebsd.org/D20407
Expose the same fields and widths from both vtio buses, even though they
don't quite line up; several virtio drivers can attach to both buses,
and sharing a PNP info table for both seems more convenient.
In practice, I doubt any virtio driver really needs to match on anything
other than bus and device_type (eliminating the unused entries for
vtmmio), and also in practice device_type is << 2^16 (so far, values
range from 1 to 20). So it might be fine to only expose a 16-bit
device_type for PNP purposes. On the other hand, I don't see much harm
in overkill here.
Reviewed by: bryanv, markj (earlier version)
Differential Revision: https://reviews.freebsd.org/D20406
random(4) masks unregistered entropy sources. Prior to this revision,
virtio_random(4) did not correctly register a random_source and did not
function as a source of entropy.
Random source registration for loadable pure sources requires registering a
poll callback, which is invoked periodically by random(4)'s harvestq
kthread. The periodic poll makes virtio_random(4)'s periodic entropy
collection redundant, so this revision removes the callout.
The current random source API is somewhat limiting, so simply fail to attach
any virtio_random devices if one is already registered as a source. This
scenario is expected to be uncommon.
While here, handle the possibility of short reads from the hypervisor random
device gracefully / correctly. It is not clear why a hypervisor would
return a short read or if it is allowed by spec, but we may as well handle
it.
Reviewed by: bryanv (earlier version), markm
Security: yes (note: many other "pure" random sources remain broken)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20419
This change enables natural scrolling with two finger scroll enabled
and when user is using a trackpad (mouse and trackpoint are not affected).
Depending on trackpad model it can be activated with setting of
hw.psm.synaptics.natural_scroll or hw.psm.elantech.natural_scroll sysctl
values to 1.
Evdev protocol is not affected by this change too. Tune userland client
e.g. libinput to enable natural scrolling in that case.
Submitted by: nyan_myuji.xyz
Reviewed by: wulf
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20447
completions are not in a consistent state. Cope with the different
places the normal I/O completion polling thread can be interrupted and
then re-entered during a kernel panic + dump.
Reviewed by: jhb and markj (both prior versions)
Differential Revision: https://reviews.freebsd.org/D20478
When starting a command also print the opcode and flags.
More consitently print flags as hex.
Use slot_printf rather than printf in one case.
MFC after: 6 weeks
Reviewed by: marius, kibab, imp
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D19748
receive sockbuf's high water mark.
Calculate rx credits on the spot instead of tracking sbused/sb_cc and
rx_credits in the toepcb. The previous method worked when the high
water mark changed due to SB_AUTOSIZE but not when it was adjusted
directly (for example, by the soreserve in nfsrvd_addsock).
This fixes a connection hang while running iozone over an NFS mounted
share where nfsd's TCP sockets are being handled by t4_tom.
MFC after: 3 days
Sponsored by: Chelsio Communications
I introduced an obvious compiler error in r346282, so this change fixes
that.
Unfortunately, RANDOM_LOADABLE isn't covered by our existing tinderbox, and
it seems like there were existing latent linking problems. I believe these
were introduced on accident in r338324 during reduction of the boolean
expression(s) adjacent to randomdev.c and hash.c. It seems the
RANDOM_LOADABLE build breakage has gone unnoticed for nine months.
This change correctly annotates randomdev.c and hash.c with !random_loadable
to match the pre-r338324 logic; and additionally updates the HWRNG drivers
in MD 'files.*', which depend on random_device symbols, with
!random_loadable (it is invalid for the kernel to depend on symbols from a
module).
(The expression for both randomdev.c and hash.c was the same, prior to
r338324: "optional random random_yarrow | random !random_yarrow
!random_loadable". I.e., "random && (yarrow || !loadable)." When Yarrow
was removed ("yarrow := False"), the expression was incorrectly reduced to
"optional random" when it should have retained "random && !loadable".)
Additionally, I discovered that virtio_random was missing a MODULE_DEPEND on
random_device, which breaks kld load/link of the driver on RANDOM_LOADABLE
kernels. Address that issue as well.
PR: 238223
Reported by: Eir Nym <eirnym AT gmail.com>
Reviewed by: delphij, markm
Approved by: secteam(delphij)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20466
misleading indentation. This is found by gcc -Wmisleading-indentation
Approved by: erj
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D20428
it hasn't been initialized.
This fixes a bug in r346570 that could cause a panic when servicing
TCP_INFO for offloaded connections.
MFC after: 3 days
Sponsored by: Chelsio Communications
ENAv2 introduces many new features, bug fixes and improvements.
Main new features are LLQ (Low Latency Queues) and independent queues
reconfiguration using sysctl commands.
The year in copyright notice was updated to 2019.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
For easier debugging, the reset is being triggered and the reset reason is
being set only in case it is done for the first time. Such approach will
ensure that the first reset reason is not going to be overwritten and
will make it easier for debugging.
Also, add a reset trigger upon invalid Tx requested ID.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
If the call to ena_up() in ena_restore_device() fails, next usage of
`ifconfig up` will cause NULL pointer dereference.
This patch adds additional checks to prevent that.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Some messages were missing new line character and traces were not having
unified behavior. To fix that, each trace and printout should add new
line character at the end of each string - that should improve
readability.
Submitted by: Rafal Kozik <rk@semihalf.com>
Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
If the headers of the packets are split into multiple segments of the
mbuf chain, the previous version of ena_tx_csum which was assuming,
that all segments will lay in the first mbuf, will eventually fail to
map the headers properties to meta descriptor.
That will cause Tx checksum offload to do not work and was leading to
memory corruption. It could even cause the crash of the system.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
For alignment with Linux driver and better handling ena_detach(), the
reset is now calling ena_device_restore() and ena_device_destroy().
The ena_device_destroy() is also being called on ena_detach(), so the
code will be more readable.
The watchdog is now being activated after reset only, if it was active
before.
There were added additional checks to ensure, that there is no race with
the link state change AENQ handler.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
As the ENA can have multiple states turned on/off, it is more convenient
to store them in single bitfield instead of multiple boolean variables.
The bitset FreeBSD API was used for the bitfield implementation, as it
provides flexible structure together with API which also supports atomic
bitfield operations.
For better readability basic macros from API were wrapped into custom
ENA_FLAG_* macros, which are filling up common parameters for all calls.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Before the patch, error handling was not releasing all resources and
was not issuing device reset if the reset task failed.
That could cause memory leak and fault of the device.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The host info bdf field is the abbreviation for the bus, device,
function of the PCI on which the device is being attached to.
Now the driver is filling information about that using FreeBSD RID
resource.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The new ENA HAL is introducing API, which can determine on Tx path if
the doorbell is needed.
That way, it can tell the driver, that it should call an doorbell.
The old threshold value wasn't removed, as not all HW is supporting this
feature - so it was reworked to also work with the new API.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The Rx ring size can be as high as 8k. Because of that we want to limit
the cleanup threshold by maximum value of 256.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
LLQ (Low Latency Queue) is the feature, that allows pushing header
directly to the device through PCI before even DMA is triggered.
It reduces latency, because device can start preparing packet before
payload is sent through DMA.
To speed up sending data through PCI, the Write Combining is enabled,
which allows hardware to buffer data before sending them on the PCI - it
allows to reduce number of PCI IO operations.
ENAv2 is using special descriptor for the negotiation of the LLQ.
Currently, only the default configuration is supported.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Handle IO interrupts using filter routine. That way, the main cleanup
task could be moved to the separate thread using taskqueue.
The deferred Rx cleanup task was removed, and now the cleanup task is
begin called instead. That way, the Rx lock could be removed.
In addition, Queue management (wake up and stop TX ring) was added, so
the TX cleanup task can be performed mostly lockless.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The driver now supports per adapter tuning of buffer ring size and HW Rx
ring size.
It can be achieved using sysctl node dev.ena.X.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
If the requested ID was out of range, the tx_info structure was NULL and
the function was trying to access the field of the NULL object.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The if_detach was causing crash if the MSI-x configuration in the attach
failed. To prevent this issue, the ifnet is being configured at the end
of the attach function.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
In rare case, when the ifconfig is called just before kldunload, it is
possible, that ena_up routine will be called after queue locks are
released.
To prevent that, ifp is detached before the last ena_down is called and
further, the ifp is freed at the end of the function.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The ENA driver needs at least 2 MSI-x - one for admin queue, and one for
IO queues pair. If there were not enough resources to allocate more than
one MSI-x, the device should not be attached.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
bus_alloc_resource_any() is not returning error value in case of an
error.
If the function call fails, the error value was not passed to the
ena_up() function.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
To prevent errors from assigning values from the DMA structure in case
of an error, zero the vaddr and paddr values upon failure.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The DMA in FreeBSD requires explicit synchronization. ENA driver was
only doing PREREAD and PREWRITE synchronizations. Missing
bus_dmamap_sync() calls were added.
It is also required to synchronize DMA engine before unloading DMA map.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
If the first MSI-x won't be executed, then the timer service will detect
that and trigger device reset.
The checking for missing Tx completion was reworked, so it will also
check for missing interrupts. Checking number of missing Tx completions
can be performed after loop, instead of checking it every iteration.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
The new ena_com allows the number of CPUs to be passed to the device in
the host info structure as a hint.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Information about Tx error should be only displayed, if packet
preparation failed due to error other than out of memory.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Whenever the driver will receive too many descriptors from the device,
it should trigger the device reset, as it is indicating that the device
is in invalid state.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Receive Side Scaling is optional feature that could be enabled in kernel
configuration by defining flag RSS.
Kernel uses hash to store and find protocol control block which is
stored in hash tables.
Kernel and NIC hash functions must be consistent. Otherwise case lookup
fails.
To achieve this kernel provides API to set proper hash key to NIC.
As it is not possible to change key for virtual ENA NIC, this driver
cannot support RSS function.
ENA is designed to work in virtual environments so supporting hardware
version of this card is unnecessary.
Submitted by: Rafal Kozik <rk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Notification AENQ handler is responsible for handling requests from ENA
device. Missing Tx threshold, Tx timeout and keep alive timeout can be
set using hints from the aenq descriptor which can be delivered in the
ENA admin notification.
The queue suspending and resuming tasks are not supported by the
driver.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
ENA_ADMIN_FATAL_ERROR and ENA_ADMIN_WARNING aenq groups were indicated
as supported, so the unimplemented_aenq_handler() will print out error
message, whenever an error will occur within the ENA admin context.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
As the ENA is working only in virtualized environment, the active media
is not specified. Instead, the active link type is set as unknown.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
Recent HAL change preparing to support ENAv2 required minor driver
modifications.
The ena_com_sq_empty_space() is not available in this ena-com, so it had
to be replaced with ena_com_free_desc().
Moreover, the ena_com_admin_init() is no longer using 3rd argument
indicating if the spin lock should be initialized, so it was removed.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon, Inc.
the code is not guarded by the if clause and has misleading indentation.
Approved by: scottl
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D20427
Since drm2 removal, there has not been any consumer of the feature in the
tree. I am also unaware of any out-of-tree consumer.
More importantly, the feature has been broken from the very start, both
before and after r306589, because the ivar was set on a device that does
not support it and it was read from another device that also does not
support it.
A bus-wide no-stop flag cannot be implemented as an ivar as iicbus
attaches as a child of various drivers. Implementing the ivar in each
and every I2C driver is just impractical.
If we ever want to implement this feature properly, then probably the
easiest way to do it would be via a flag in the softc of iicbus.
In fact, we might have to do that in the stable branches if we want to
fix the code for them.
Reported by: ian (long time ago)
MFC after: 1 month (maybe)
X-MFC-note: cannot just merge the change, must keep drm2 happy
As I see, different NICs in different configurations may have different
numbers of TX and RX queues. The code was assuming 1:1 mapping between
event queues (interrupts) and TX/RX queues. Since number of interrupts
is set to maximum of TX and RX queues, when those two are different, the
system is doomed.
I have no documentation or deep knowledge about this hardware, so this
change is based on general observations and code reading. If some of my
guesses are wrong, please do better. I just confirmed HP NC550SFP NICs
are working now.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Prior to this revision, vtpci's BUS_READ_IVAR method on VIRTIO_IVAR_SUBVENDOR
accidentally returned the PCI subdevice.
The typo seems to have been introduced with the original commit adding
VIRTIO_IVAR_{{SUB,}DEVICE,{SUB,}VENDOR} to virtio_pci. The commit log and code
strongly suggest that the ivar was intended to return the subvendor rather than
the subdevice; it was likely just a copy/paste mistake.
Go ahead and rectify that.
- Perform ifp mismatch checks (to determine if a send tag is allocated
for a different ifp than the one the packet is being output on), in
ip_output() and ip6_output(). This avoids sending packets with send
tags to ifnet drivers that don't support send tags.
Since we are now checking for ifp mismatches before invoking
if_output, we can now try to allocate a new tag before invoking
if_output sending the original packet on the new tag if allocation
succeeds.
To avoid code duplication for the fragment and unfragmented cases,
add ip_output_send() and ip6_output_send() as wrappers around
if_output and nd6_output_ifp, respectively. All of the logic for
setting send tags and dealing with send tag-related errors is done
in these wrapper functions.
For pseudo interfaces that wrap other network interfaces (vlan and
lagg), wrapper send tags are now allocated so that ip*_output see
the wrapper ifp as the ifp in the send tag. The if_transmit
routines rewrite the send tags after performing an ifp mismatch
check. If an ifp mismatch is detected, the transmit routines fail
with EAGAIN.
- To provide clearer life cycle management of send tags, especially
in the presence of vlan and lagg wrapper tags, add a reference count
to send tags managed via m_snd_tag_ref() and m_snd_tag_rele().
Provide a helper function (m_snd_tag_init()) for use by drivers
supporting send tags. m_snd_tag_init() takes care of the if_ref
on the ifp meaning that code alloating send tags via if_snd_tag_alloc
no longer has to manage that manually. Similarly, m_snd_tag_rele
drops the refcount on the ifp after invoking if_snd_tag_free when
the last reference to a send tag is dropped.
This also closes use after free races if there are pending packets in
driver tx rings after the socket is closed (e.g. from tcpdrop).
In order for m_free to work reliably, add a new CSUM_SND_TAG flag in
csum_flags to indicate 'snd_tag' is set (rather than 'rcvif').
Drivers now also check this flag instead of checking snd_tag against
NULL. This avoids false positive matches when a forwarded packet
has a non-NULL rcvif that was treated as a send tag.
- cxgbe was relying on snd_tag_free being called when the inp was
detached so that it could kick the firmware to flush any pending
work on the flow. This is because the driver doesn't require ACK
messages from the firmware for every request, but instead does a
kind of manual interrupt coalescing by only setting a flag to
request a completion on a subset of requests. If all of the
in-flight requests don't have the flag when the tag is detached from
the inp, the flow might never return the credits. The current
snd_tag_free command issues a flush command to force the credits to
return. However, the credit return is what also frees the mbufs,
and since those mbufs now hold references on the tag, this meant
that snd_tag_free would never be called.
To fix, explicitly drop the mbuf's reference on the snd tag when the
mbuf is queued in the firmware work queue. This means that once the
inp's reference on the tag goes away and all in-flight mbufs have
been queued to the firmware, tag's refcount will drop to zero and
snd_tag_free will kick in and send the flush request. Note that we
need to avoid doing this in the middle of ethofld_tx(), so the
driver grabs a temporary reference on the tag around that loop to
defer the free to the end of the function in case it sends the last
mbuf to the queue after the inp has dropped its reference on the
tag.
- mlx5 preallocates send tags and was using the ifp pointer even when
the send tag wasn't in use. Explicitly use the ifp from other data
structures instead.
- Sprinkle some assertions in various places to assert that received
packets don't have a send tag, and that other places that overwrite
rcvif (e.g. 802.11 transmit) don't clobber a send tag pointer.
Reviewed by: gallatin, hselasky, rgrimes, ae
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D20117
The point of r345008 was to reset the Command Reference Number (CRN)
in some situations where a device stayed in the topology, but had
changed somehow.
This can include moving from a switch connection to a direct
connection or vice versa, or a device that temporarily goes away
and comes back. (e.g. moving to a different switch port)
There were a couple of bugs in that change:
- We were reporting that a device had not changed whenever the
Establish Image Pair bit was not set. That is not quite correct.
Instead, if the Establish Image Pair bit stays the same (set or
not), the device hasn't changed in that way.
- We weren't setting PRLI Word0 in the port database when a new
device arrived, so comparisons with the old value for the
Establish Image Pair bit weren't really possible. So, make sure
PRLI Word0 is set in the port database for new devices.
- We were resetting the CRN whenever the Establish Image Pair bit
was set for a device, even when the device had stayed the same
and the value of the bit hadn't changed. Now, only reset the
CRN for devices that have changed, not devices that sayed the
same.
The result of all of this was that if we had a single FC device on
an FC port and it went away and came back, we would wind up
correctly resetting the CRN.
But, if we had multiple devices connected via a switch, and there
was any change in one or more of those devices, all of the devices
that stayed the same would also have their CRN values reset.
The result, from a user standpoint, is that the tape drives, etc.
would all start to time out commands and the initiator would send
aborts.
sys/dev/isp/isp.c:
In isp_pdb_add_update(), look at whether the Establish
Image Pair bit has changed as part of the check to
determine whether a device is still the same. This was
causing erroneous change notifications. Also, when
creating a new port database entry, initialize the
PRLI Word 0 values.
sys/dev/isp/isp_freebsd.c:
In isp_async(), in the changed/stayed case, instead of
looking at the Establish Image Pair bit to determine
whether to reset the CRN, look at the command value.
(Changed vs. Stayed.) Only reset the CRN for devices
that have changed.
Sponsored by: Spectra Logic
MFC after: 3 days
That made, for example, gpioc -l output quite hard to read and parse.
Also, fix formatting of a nearby statement with too long lines.
MFC after: 2 weeks
Pull the responsibility for zeroing events, which is general to any
conceivable implementation of a random device algorithm, out of the
algorithm-specific Fortuna code and into the callers. Most callers
indirect through random_fortuna_process_event(), so add the logic there.
Most callers already explicitly bzeroed the events they provided, so the
logic in Fortuna was mostly redundant.
Add one missing bzero in randomdev_accumulate(). Also, remove a redundant
bzero in the same function -- randomdev_hash_finish() is obliged to bzero
the hash state.
Reviewed by: delphij
Approved by: secteam(delphij)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D20318
This takes the SPCR code currently in uart_cpu_arm64.c, moves it into
a new uart_cpu_acpi.c (with some associated refactoring), and uses it
from both arm64 and x86.
An SPCR serial port address AccessWidth field value of 0 ("reserved")
is now treated as 1 ("byte access") in order to work around a buggy
SPCR table on Amazon EC2 i3.metal instances.
Reviewed by: manu, Greg V
MFC after: 3 days
Sponsored by: https://www.patreon.com/cperciva
Differential Revision: https://reviews.freebsd.org/D20357
Pnpinfo is bus-specific and requires the bus name. The FDTCOMPAT_PNP_INFO()
macro makes it easier to define new FDT-based pnpinfo for busses other than
simplebus.
Differential Revision: https://reviews.freebsd.org/D20382
Many i2c slave drivers are in modules that can be unloaded. If they detach
while IO is in progress the bus would be hung forever. Conversely,
lower-layer drivers (iicbus and the hardware driver) also live in modules
and other kinds of bad things happen if they get detached while IO is in
progress. Because device_busy() propagates up to parents, marking the slave
device busy while it owns the bus solves both kinds of problems that come
with detaching i2c devices while IO is in progress.
It should be safer to flush controller and disk caches on the shutdown.
And to gracefully shut down the controller as well.
It seems that the Linux driver has been doing that for a long time.
Discussed with: scottl
Reviewed by: imp, Sumit Saxena <sumit.saxena@broadcom.com>
(both earlier version)
MFC after: 3 weeks
Sponsored by: Panzura
Differential Revision: https://reviews.freebsd.org/D19817
hint.gpioled.%d.state determines the initial state of the LED when the
driver takes control over it:
0 - the LED is off
1 - the LED is on
-1 - the LED is kept as it was
While here, add a module version declaration.
MFC after: 2 weks
