- Implement support for interrupt filters in the DWC OTG driver, to
reduce the amount of CPU task switching when only feeding the FIFOs.
- Add common spinlock to the USB bus structure.
MFC after: 2 weeks
the main processing queue, clear the NAK counter for any associated
BULK or CONTROL transfers and poll the endpoint(s) for 1 millisecond
at 125us rate interval, before going into slow, 10ms, NAK polling mode
again. This has the effect that typical ping-ping protocols respond
quicker when initiated from the USB host.
MFC after: 2 weeks
- For non-periodic traffic we only need to wait two SOFs before
disabling the channel.
- Make sure we release the TX FIFO tracking level after the host
channel is disabled.
- Make sure the host channel state gets reset/disabled initially.
- Two minor code style changes.
MFC after: 2 weeks
- Rework how we allocate and free USB host channels, so that we only
allocate a channel if there is a real packet going out on the USB
cable.
- Use BULK type for control data and status, due to instabilities in
the HW it appears.
- Split FIFO TX levels into one for the periodic FIFO and one for the
non-periodic FIFO.
- Use correct HFNUM mask when scheduling host transactions. The HFNUM
register does not count the full 16-bit range.
- Correct START/COMPLETION slot for TT transactions. For INTERRUPT and
ISOCHRONOUS type transactions the hardware always respects the ODDFRM
bit, which means we need to allocate multiple host channels when
processing such endpoints, to not miss any so-called complete split
opportunities.
- When doing ISOCHRONOUS OUT transfers through a TT send all data
payload in a single ALL-burst. This deacreases the likelyhood for
isochronous data underruns.
- Fixed unbalanced unlock in case of "dwc_otg_init_fifo()" failure.
- Increase interrupt priority.
MFC after: 2 weeks
controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
speed data traffic going directly to a USB device or through a
so-called USB transaction translator.
Add checks that we are not overusing the TX FIFO.
MFC after: 2 weeks
define a few imx_ccm_foo() functions that are implemented by the imx51 or
imx6 ccm code. Of course, the imx6 ccm code is still more a wish than
reality, so for now its implementations just return hard-coded numbers.
a jtag debugging product, which was used on early Beaglebone boards (later
boards used a standard FTDI 2232C product ID). Change the name accordingly,
and also add an entry for XDS100V3, the latest version of that product
which has its own new product ID number.
Device type and revision is now determined from the bcdDevice field and
doesn't need to be in the table at all. The feature that skips creation
of /dev/ttyU* entries for jtag and gpio interfaces is enhanced:
- The feature is now optional, but enabled by default. A tunable and
sysctl are available to control it: hw.usb.uftdi.skip_jtag_interfaces.
- We no longer assume interface #0 is the only jtag interface. Up to
eight interfaces per chip can be flagged as jtag. (Current ftdi chips
support a max of 4 interfaces; this leaves room for growth.)
- Some manufacturers don't change the product ID or use the same ID for
different devices intended for both serial-comms and jtag/gpio use.
Often while the product ID is the same, the product name string is
different, so it's now possible to search for the product name in a
table of strings and get the set of non-tty interfaces from that table.
- Add a comment about FTDI and ZLPs.
- Correctly check odditiy of baud rate divisor.
- Correct IOCTL handling for "error" and "event" char.
MFC after: 1 weeks
other modes supported by the FTDI serial adapter chips.
In addition to adding the new ioctls, this change removes all the code
that reset the chip at attach and open/close time, and also the code
that turned on RTS/CTS flow control on open without any permission to do
so (that was just always a bug in the driver).
When FTDI chips are configured as GPIO or MPSSE or other special-purpose
uses by an attached serial eeprom, the chip will power on with certain
pins driven or floating, and it's important that the driver not do
anything to the chip to perturb that unless it receives a specific
command to do so. When used for "plain old serial comms" the chip
powers on into the right mode and never needs to be reset while it's
running to operate properly, so this change is transparent to most users.
While I'm here, remove aue_eeprom_getword() as its only usage is to
read station address and make it more readable. This change is
inspired by NetBSD.
With this change, aue(4) should work on big endian architectures.
PR: 188177
default wMaxPacketSize (64 or 512 bytes). This actually helps older FTDI
devices (which were USB 1/full speed) more than the new H-series high
speed, but even for the new chips it helps cut the number of interrupts
when doing very high speed (3-12mbaud).
Recent FDTI chips have the ability to operate at up to 12mbps. The newer
chips with faster clocks have the same usb vendor/product IDs as the older
chips; the bcdDevice field must be used to detect the newer versions. This
change includes a new function to do that instead of using just the IDs from
the vendor/product table.
The code to choose the baud clock divisor is completely rewritten. In
addition to supporting the new higher clock rates, the rewrite fixes a
longstanding bug in the old code which put the high bits of the fractional
part of the divisor into the wrong place in the wIndex field. That bug
was mostly harmless -- it accidentally didn't affect standard baud rates
and would only show up when using relatively fast non-standard rates.
create character devices. The deadlock can happen if an application is
issuing IOCTLs which require USB refcounting, at the same time the USB
device is detaching.
There is already a counter in place in the USB device structure to
detect this situation, but it was not always checked ahead of invoking
functions that might destroy character devices, like detach, set
configuration, set alternate interface or detach active kernel driver.
Reported by: Daniel O'Connor <doconnor@gsoft.com.au>
MFC after: 1 week
The NetBSD Foundation states "Third parties are encouraged to change the
license on any files which have a 4-clause license contributed to the
NetBSD Foundation to a 2-clause license."
This change removes clauses 3 and 4 from copyright / license blocks that
list The NetBSD Foundation as the only copyright holder.
Sponsored by: The FreeBSD Foundation
