This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
and initializes the next two ports in order starting at 03e0. This
also patches pcic_p.h to reduce the I/O ports mapped from 4 to 2.
Submitted by: Ted Faber <faber@ISI.EDU>
option PCIC_NOCLRREGS). This is now the default behavior since it's
apparently required for the CLPD6832, and doesn't negatively affect
any of my test machines.
Requested by: Ted Faber <faber@ISI.EDU>
mode. Currently, the only supported controller is the Cirrus Logic
PD6832, but others can be supported with docs on them.
Submitted by: Ted Faber <faber@ISI.EDU>
(update_intr_masks might not need to be done in 3.X, but the new generic
interrupt code is incomplete w/regard to support for the PCCARD code, so
to avoid any potential problems use it. It can't hurt).
- Correctly register pcic_imask with the system interrupt code.
- Call update_intr_masks() so that pcic_imask modifications that occur
when card interrupts are registered get updated in the system
interrupt code.
removed. Add a new state 'suspend' so we 'fake' insertion events at
resume time for the cards that have been suspended.
[
The code still works if you remove the card during suspend, switch the
card during suspend, or combinations of both.
]
Reviewed by: frf@xocolatl.com
use a Linker Set. Note, if a driver is loaded as an LKM if will have
to use the function call, but since none of the existing drivers
are loadable, this made things cleaner and boot messages nicer.
Obtained from: PAO-970616
* Kill individual drivers 'suspend' routines, since there's no simple/safe
way to suspend/resume a card w/out going through the complete probe
at initialization time.
* Default to using the apm_pccard_resume sysctl code, which basically
pretends the card was removed, and then re-inserted. Suspend/resume
is now 'emulated' with a fake insert/removal. (Hence we no longer
need the driver-specific suspend routines.)
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
own definition of ISA_HOLE_START. We shouldn't need to include
bus/processor specific code in here, but it is required. At least by
doing it this way it becomes more obvious where the bogusness is.
Obtained from: email with bde
but it has too much baggage).
- create a new routine 'unregister_device_interrupt', which is now used
instead of having two routines with the same code snippet.
- Minor cleanups and commenting.
[ No functional changes, just moving things around ]
slots. Otherwise, we try to suspend drivers who have been disabled
already.
[
The only reason the drivers are still on the list is because of race
conditions where the card is removed while the driver is in use. We
leave the drivers on the slot list (leaving all of their structures in
place in case a process is using it) but set it's state to empty so that
further uses by the pccard code know not to expect active cards.
]
from the 'lower' interrupts to the 'higher' interrupts.) We need to
find a way to set the interrupt for the controller in the config file.
Determined by: handy@sag.space.lockheed.com
sysctl option 'fakes' like a card was removed and inserted when the
machine is brought up again from a suspend. It is disabled by default,
and the old code is used.
Obtained from: PAO
speaker. Cirrus Logic PCIC chips must enable this. There is also a Low
Power Dynamic Mode bit that claims to reduce power consumption by 30%,
so enable it and hope for the best.
PR: 4650
Submitted by: Nick Sayer <nsayer@quack.kfu.com>
instead of the first available, like Win95 does. This appears to help
on some machines, and avoids potential problems with built-in serial
ports which tend to live at IRQ 3, which is usually picked with the
old method.
(pt. unused) for TI PCI1130.
2. pccard.c: PCIC_RESUME_RESET is now (also) a sysctl. (Never make it
a #ifdef if it can be made a sysctl!)
3. pcic.c: make getb() and putb() proper member functions of struct
pcic_slot. Add a couple of missing casts.
Use the name argument almost the same in all LKM types. Maintain
the current behavior for the external (e.g., modstat) name for DEV,
EXEC, and MISC types being #name ## "_mod" and SYCALL and VFS only
#name. This is a candidate for change and I vote just the name without
the "_mod".
Change the DISPATCH macro to MOD_DISPATCH for consistency with the
other macros.
Add an LKM_ANON #define to eliminate the magic -1 and associated
signed/unsigned warnings.
Add MOD_PRIVATE to support wcd.c's poking around in the lkm structure.
Change source in tree to use the new interface.
Reviewed by: Bruce Evans
