aic7xxx.c:
In target mode, reset the TQINPOS on every restart of the sequencer.
In the past we did this only during a bus reset, but there are other
reasons the sequencer might be reset.
In ahc_clear_critical_section(), disable pausing chip interrupts while
we step the sequencer out of a critical section. This avoids the
possibility of getting a pausing interrupt (unexpected bus free,
bus reset, etc.) that would prevent the sequencer from stepping.
Send the correct async notifications in the case of a BDR or bus reset.
In ahc_loadseq(), correct the calculation of our critical sections.
In some cases, the sections would be larger than needed.
aic7xxx.h:
Remove an unused SCB flag.
aic7xxx.seq:
MK_MESSAGE is cleared by the kernel, there is no need to waste
a sequencer instruction clearing it.
aic7xxx_freebsd.c:
Go through the host message loop instead of issuing a single
byte message directly in the ahc_timeout() case where we
are currently on the bus to the device. The effect is the same,
but this way we get a nice printf saying that an expected BDR
was delivered instead of an unexpected bus free.
If we are requeuing an SCB for an error recovery action, be sure
to set the DISCONNECTED flag in the in-core version of the SCB.
This ensures that, in the SCB-paging case, the sequencer will
still recognize the reselection as valid even if the version
of the SCB with this flag set was never previously paged out
to system memory. In the non-paging case, set the MK_MESSAGE
flag in SCB_CONTROL directly.
aic7xxx_pci.c:
Enable the Memeory Write and Invalidate bug workaround for
all aic7880 chips with revs < 1. This bug is rarely triggered
in FreeBSD as most transfers end on cache-aligned boundaries,
but a recheck of my references indicates that these chips
are affected.
of two (one to access the circular input fifo, the other to get the SCB).
This costs us a command slot so the driver can now only queue 254
simultaneous commands.
Have the kernel driver honor critical sections in sequencer code.
When prefetching S/G segments only pull a cacheline's worth but
never less than two elements. This reduces the impact of the
prefetch on the main data transfer when compared to the 128
byte fetches the driver used to do.
Add "bootverbose" logging for transfer negotiations.
Correct a bug in ahc_set_syncrate() that would prevent an update
of the sync parameters if only the ppr_options had changed.
Correct locking for calls to ahc_free_scb(). ahc_free_scb() is no
longer protected internally to simplify ports to other platforms.
Make sure we unfreeze our SIMQ if a resource shortage has occurred
and an SCB is been freed.
ahc_pci.c:
Turn on cacheline streaming for all controllers that support it.
Clarify diagnostic messages about PCI interrupts.
ahc_pci.c:
Bring back the AHC_ALLOW_MEMIO option at least until the
memory mapped I/O problem on the SuperMicro 370DR3 is
better understood.
aic7xxx.c:
If we see a spurious SCSI interrupt, attempt to clear it and
continue by unpausing the sequencer.
Change the interface to ahc_send_async(). Some async messages
need to be broadcast to all the luns of a target or all the
targets of a bus. This is easier to achieve by passing explicit
channel, target, and lun parameters instead of attempting to
construct a device info struct to match.
Filter the sync parameters for the PPR message in exactly the
same way we do for an old fashioned SDTR message.
Correct some typos and correct a panic message.
Handle rejected PPR messages.
In ahc_handle_msg_reject(), let ahc_build_transfer_msg() build
any additional transfer messages instead of doing this inline.
aic7xxx.h:
Increase the size of both msgout_buf and msgin_buf to
better accomodate PPR messages.
aic7xxx_freebsd.c:
Update for change in ahc_send_async() parameters.
aic7xxx_freebsd.h
Update for change in ahc_send_async() parameters.
Honor AHC_ALLOW_MEMIO.
aic7xxx_pci.c:
Check the error register before going into full blown PCI
interrupt handling. This avoids a few costly PCI configuration
space reads when we run our PCI interrupt handler because another
device sharing our interrupt line is more active than we are.
Also unpause the sequencer after processing a PCI interrupt.
Separate our platform independent hooks from core driver functionality
shared between platforms (FreeBSD and Linux at this time).
Add sequencer workarounds for several chip->chipset interactions.
Correct external SCB corruption problem on aic7895 based cards (3940AUW).
Lots of cleanups resulting from the port to another OS.
