and Rx DMA tag separately. Previously it used a common mbuf DMA tag
for both Tx and Rx path but Rx buffer(standard ring case) should
have a single DMA segment and maximum buffer size of the segment
should be less than or equal to MCLBYTES. This change also make it
possible to add TSO with minor changes.
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
PR: kern/127587
Tested by: Thomas Quinot <thomas@quinot.org> (BCM7561 A0)
MFC after: 2 weeks
Obtained from: OpenBSD
quirk requiring it to be enabled even when using MSI. This makes
the latter work again after r189285.
- Remove a comment which no longer applies since r190194.
- If boot verbose, print asicrev, chiprev and bus type on attach.
- For PCI Express devices:
1) Adjust max read request size to 4Kbytes
2) Turn on FIFO_LONG_BURST in RDMA during bge_blockinit()
Though 1) does not seem to have much to do with the poor TX performance
observed on PCI Express bge(4), 2) does fix the problem. [1]
- Nuke the RX CPU self-diag, which prevents working cards from working
(Linux tg3 does not have this diag neither does OpenBSD's bge(4)).
The increasing of the firmware handshaking timeout to 20000 retries
done as part of the original commit isn't merged as way already have a
way higher BGE_TIMEOUT of 100000.
PR: 119361 [1]
Obtained from: tg3 via DragonflyBSD [1], DragonflyBSD
- Rename BGE_FLAG_EEPROM to BGE_FLAG_EADDR to underline it's absence means
"there's no chip containing an Ethernet address fitted to the BGE chip
so we have to get it from the firmware instead" rather than "there's no
EEPROM, but maybe NVRAM or something else".
- Don't treat BCM5906[M] generally like chips w/o BGE_FLAG_EADDR set, just
in the two cases really necessary. This gets us line with the original
patch for DragonFlyBSD.
- For sparc64 restore the intended behavior of obtaining the Ethernet
address from the firmware in case BGE_FLAG_EADDR is not set, even for
BCM5906[M].
- Fix some style(9) bugs introduced with rev. 1.208 of if_bge.c
Approved by: jhb
Additional testing by: Thomas Nystroem (BCM5906)
all cards/modes.
In addition to the intr forcing added with rev. 1.205 adopt the other
places to use the same logic.
We need to exclude a few chips/revisions (5700, 5788) from using the
enhanced version and fall back to the old way as that is the only
method they support.
Tested by: phk
Suggested by: davidch, Broadcom (thanks a lot for the help!)
MFC after: 16 days
10/100 operation and place the mailbox registers at a different offset.
They also do not have an EEPROM, so the MAC address must be read from
NVRAM instead.
MFC after: 1 month
PR: kern/118975
Submitted by: benjsc, Thomas Nyström thn at saeab dot se
Submitted by: sephe (original patch for DragonflyBSD)
Blade 2500, Fire V210 and probably some other sparc64 machines.
These chips are typically not fitted with an EEPROM which means
that we have to obtain the MAC address via OFW and that some chip
tests will just always fail.
These changes are based on the respective code found in OpenBSD
with some additional info obtained from OpenSolaris and some style
suggestions by jkim@. They also have the desired side-effect of
respecting the 'local-mac-address?' system configuration variable
for the affected BGEs.
- In bge_attach() factor out calling bge_release_resources() before
going to the fail label into the fail label as well as replace a
magic 6 with ETHER_ADDR_LEN.
Reviewed by: yongari (before style changes), jkim
- Move some PHY bug detections from brgphy.c to if_bge.c.
- Do not penalize working PHYs.
- Re-arrange bge_flags roughly by their categories.
- Fix minor style(9) nits.
PR: kern/107257
Obtained from: OpenBSD
Tested by: Mike Hibler <mike at flux dot utah dot edu>
- Do not repeatedly read vendor/device IDs while probing.
- Remove redundant bzero(3) for softc. device_get_softc(9) does it for free[1].
Reviewed by: glebius
Suggested by: glebius[1]
- Use the appropriate register writing method when reseting the chip
- Program the descriptor DMA engine correctly.
- More reliably detect certain chips and their features.
Also add some low-level debugging tools to help future work on this driver.
Submitted by: David Christenson (proof of concept changes)
Sponsored by: www.UIA.net
discarded RX packets to input error for BCM5705 or newer chipset as the others.
Unfortunately we cannot do the same for output errors because ifOutDiscards
equivalent register does not exist. While I am here, replace misleading and
wrong BGE_RX_STATS/BGE_TX_STATS with BGE_MAC_STATS. They were reversed but
worked accidently.
to it. Try to co-operate with the IPMI/ASF firmware accessing the PHY.
One we get link we don't mess with the PHY. If we do then over time
the NIC will go off line. It would be nice if we could tell if IPMI
was enabled on the chip but I can't figure out a reliable way to do
that. The scheme I tried worked on a Dell PE850 but not on an HP machine.
So we assume any NIC that has ASF capability needs to deal with it.
The code was inspired by the support in Linux from kernel.org and Broadcom.
Broadcom did give me some info. but it is rather limited and is mostly
just what is in the Linux driver. Thanks to the numerous people that
helped debug the many prior versions and that I didn't break other
bge(4) HW.
Reviewed by: several people
Tested by: even more
BCM5787 based NICs.
- Recognize BCM5703 B0 ASIC.
- Rewrite the jumbo capability matching macro, so that chips known
to work are listed there. [*]
[*] I'm still not sure about this. Probably more corrections
will be done to this macro after discussion with davidch@
and brad@OpenBSD.
Obtained from: OpenBSD (brad)
- Add more device IDs, ASIC revisions and chip IDs.
- Rewrite a bit code that picks the description for device.
- Introduce several macros to shorten quirks for bugs and
features.[*]
- Use some magic values, that OpenBSD has successfully
possessed from Linux (Broadcom supplied) driver.
- Remove disabled code that tried to access VPD.
[*] The macro that matches Jumbo capable NICs is
rewritten to preserve our current behavior. I
need clarify whether our or theirs is correct.
PR: 68351 (and may be others)
Obtained from: OpenBSD, brad@ mostly
2) add missing bus_dmamap_sync() call in bge_intr()
Tested by: Husnu Demir <hdemir AT metu DOT edu DOT tr>
Approved by: glebius (mentor)
MFC after: 3 days
as input/output interface errors.
- Keep values of rx/tx discards & tx collisions inside struct bge_softc.
So we can keep statistic across ifconfig down/up runs (cause bringing
bge up will reset chip).
Approved by: glebius (mentor)
MFC after: 1 week
we can cache its value in the softc. Eliminates one PCI register
write per call to bge_start().
A 1.8% speedup for UDP_RR test on my old box.
Obtained from: NetBSD(jonathan) via delphij
- Give up endianess support and switch to native-endian format for
accessing hardware structures. In fact embedded processor for
BCM57xx is big-endian architure(MIPS) and it requires native-endian
format for NIC structures.The NIC performs necessary byte/word
swapping depending on programmed endian type.
- With above changes all htole16/htole32 calls were gone.
- Remove bge_vhandle member in softc and changed to use explicit
register access. This may add additional performance penalty
that than that of previous memory access. But most of the access
is performed on initialization phase(e.g. RCB setup), it would be
negligible.
Due to incorrect use of bus_dma(9) in bge(4) it still panics sparc64
system in device detach path. The issue would be fixed in next patch.
Reviewed by: jkim (initial version)
Silence from: ps
Tested by: glebius
Obtained from: NetBSD via OpenBSD
cluster allocator, that wasn't MPSAFE. Instead, utilize our new generic
UMA jumbo cluster allocator. Since UMA gives us a 9k piece that is contigous
in virtual memory, but isn't contigous in physical memory we need to handle
a few segments. To deal with this we utilize Tigon chip feature - extended
RX descriptors, that can handle up to four DMA segments for one frame.
Details:
o Remove bge_alloc_jumbo_mem(), bge_free_jumbo_mem(),
bge_jalloc(), bge_jfree() functions.
o Remove SLIST heads, bge_jumbo_tag, bge_jumbo_map from softc.
o Use extended RX BDs for Jumbo receive producer ring, and
initialize it appropriately.
o New bge_newbuf_jumbo():
- Allocate an mbuf with Jumbo cluster with help of m_cljget().
- Load the cluster for DMA with help of bus_dmamap_load_mbuf_sg().
- Assert that we got 3 segments in the DMA mapping.
- Fill in these 3 segments into the extended RX descriptor.
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
