that enabling busmastering would result in PCR bit ON after codec
reset.
While I'm here add DELAY(1) to codec access routine to give reasonable
time to codec operation. Without the delay, it would cause problems on
super-fast machines(> 2GHz). Also enable legacy audio for all 6300ESB,
82801[D-G]B chips. Previously, it enabled legacy audio for 82801DB(ICH4)
chip only.
Reported by: Maxim Maximov mcsi AT mcsi DOT pp DOT ru
Andrew Bliznak andriko.b AT gmail DOT com
Tested by: brueffer, Maxim Maximov, Andrew Bliznak
erratic system slowdown (beaten to a pulp) and possible panic. This
issue has bugged me for as long as I could remember, until I
realized that it is possible for register base offset to hold zero
value which is definitely a "FALSE".
Approved by: netchild (mentor)
compatible AC97 codec.
- As the driver supports so many variants, create a table ids for
ease of probing and maintenance.
Submitted by: yongari
Reviewed/Tested by: multimedia@
- From luigi:
The code to compute fragment sizes in the ich driver almost
invariably ends up using the full buffer available, no matter
how the user specifies fragment size and number.
With audio telephony (8khz, 16bit-stereo) and the 16k buffer
size this results in an unbearable 500ms delay.
This patch makes sure that we never use more than 4 fragments,
(i don't think we need more unless there are huge interrupt
servicing latencies), and obey to the requested fragment size,
so that latency is acceptable.
Based on this (and after much regression tests), I can conclude
that this driver works best with 2 fragments, thus solving various
long standing issues of ICH driver not capable to flush or play
short files perfectly.
Suggested by: luigi (the idea of smaller fragments)
- MPSAFE conversion.
Approved by: netchild (mentor)
distinct hardware playback channels. DAC configuration can be
accessed through kernel hint - hint.pcm.<unit>.dac="val" with
following possible values:
0 = Enable both DACs (default)
1 = Enable single DAC (DAC1)
2 = Enable single DAC (DAC2)
3 = Enable both DACs, swap position (DAC2 comes first instead
of DAC1)
Special case for ES1370:
Unlike ES1371,2,3/CT5880, volume for each DAC 1 and 2 can be
controlled indepedently (synth for DAC1, pcm for DAC2). It is
possible that user will confuse by this behaviour, since both
DACs are enabled by default. Thus, provide a knob through sysctl
hw.snd.pcm<unit>.single_pcm_mixer:
0 = each DACs will be controlled separately (synth/pcm).
1 = combine both DACs volume mixer controller into a single
"pcm" (default)
As a side note, fixed rate operation (provided by previous
commit) is not a mandatory if the configuration space does not
involve DAC2 (perhaps disabled by user through the above kernel
hint). Unlike DAC2, DAC1 has its own register / control space,
not affected by the speed settings of ADC.
Tested by: multimedia@
Approved by: netchild (mentor)
- Don't keep the SPDIF state in the driver private struct since it
can be overriden by hand with pciconf(8), query it when needed instead.
Regarding the locking I let Ariff explain it himself:
---snip---
About the locking, that is what I'm intended to do since the beginning.
The reason I'm not putting that along since my first patchset was
because several people especially from amd46 camp reported that it cause
lots of LORs, which is weird considering that I've never encounter such
in a pretty much strict locking environment (i386). However, since our
previous discussion with Pyun YongHyeon about strict locking, I've
decided to bring it back for all the affected drivers, not just for
es137x. It turns out that the root of the problem was within dsp.c
during device open, which has been fixed since dsp.c revision 1.84.
---snip---
Submitted by: Ariff Abdullah <skywizard@MyBSD.org.my>
code which may help.
People with a ich compatible soundcard which want to help out should
change the "#if 1" to a "#if 0" and try if the soundcard still works.
Reports about working or not-working soundcards with this change to
multimedia@ please.
PR: 73987
sampling rate between playback and recording. This can be
disabled / enabled via kernel hints
(hint.pcm.<unit>.fixed_rate=0/4000-48000) or sysctl
hw.snd.pcm<unit>.fixed_rate=0/4000-48000). Default to 48khz
fixed rate. [1]
* Basic cleanup. *_es1371x_* -> *_es137x_*.
* Some locking fixes. [2]
Submitted by: Ariff Abdullah <skywizard@MyBSD.org.my>
Discussed with: yongari [2]
See also: http://lists.freebsd.org/pipermail/freebsd-multimedia/2005-September/002758.html [1]
Reported by: Jos Backus <jos at catnook.com> [1]
In case this causes trouble for some other chipsets add a comment how to
proceed. If we don't get bugreports, this should be removed after a while
(some releases?).
PR: 56617 [1], 29465, 39260, 40574, 68225
Submitted by: Matthew E. Gove <mgove@comcast.net> [1]
* Add kernel hint option to disable DXS channels entirely. Report
from several skype users / Pav Lucistnik indicate that disabling
DXS may fix lots of pop / crackling noise. To disable DXS add
hint.pcm.<unit>.via_dxs_disabled="1" to /boot/device.hints.
Further investigation of the issues regarding DXS showed, that
the problem is in another (more generic) place, but until the
right fix is tested/reviewed this may help a little bit.
Added sysctl's to aid testing/debugging:
hint.pcm.<unit>.via_dxs_disabled=X - Disable / Enable DXS channels entirely
hint.pcm.<unit>.via_dxs_channels=X - Limit DXS channels up to X
hint.pcm.<unit>.via_sgd_channels=X - Limit SGD channels up to X
hint.pcm.<unit>.via_dxs_src=X - Enable / Disable DXS sample rate
converter.
Submitted by: Ariff Abdullah <skywizard@MyBSD.org.my>
Tested by: multimedia@
especially for CT4730 / EV1938 chip, causing misconfigured mixer
(David Xu), crippled after power cycle (Kevin Oberman). Fixed.
* Incorporate locking/spdif patches from Jon Noack / matk. Not all
es137x can really do spdif, clean it up a bit to only let few capable
chip. This adds a "hw.snd.pcm<unit>.spdif_enabled" sysctl until
a more generic way of handling this from userland (by an ordinary
user) is designed/implemented.
* Convert all bus_space_(read|write) to use es_rd/es_wr, simmilar
with other drivers.
* Add tunable hw.snd.pcm<unit>.latency_timer sysctl to toggle pci
latency timer value on the fly. Much noise / pop / crackling
issues can be solved by increasing its value. Other people have
pointed out to use pciconf instead, but this is just an added
value specific for CT4730/EV1938.
* Remove es137x specific debug sysctl/code.
Several PRs can now be closed.
Submitted by: Ariff Abdullah <skywizard@MyBSD.org.my>
Submitted by: Jon Noack <noackjr@alumni.rice.edu> (implicit)
Submitted by: matk (implicit)
PR: 59349, 68594, 73498
Tested by: multimedia@
handle DMA addresses located above 1GB. The LBA(loop begin address)
register which holds DMA base address is 32bits register. But the
MSB 2bits are used for other purposes. This effectivly limits the
DMA address space up to 1GB.
Approved by: jake (mentor)
Reviewed by: truckman, matk
assign DMA address to the wrong address. It can cause system lockup
or other mysterious errors. Since most sound cards requires low DMA
address(BUS_SPACE_MAXADDR_24BIT) sndbuf_alloc() would fail when the
audio driver is loaded after long running of operations.
Approved by: jake (mentor)
Reviewed by: truckman, matk
allocation. Notably, in this case, the driver tries to allocate several
pieces of memory and then fails if the pieces allocated after the first
do not come after it physically, and within a specific range (8MB I
believe). Of course, this could just as easily fail for any number of
reasons, but it almost always fails now that contiguous allocations start
at the end of possible specified memory locations rather than the beginning.
Allocate all the possibly-needed memory up front, even though it's a waste,
to get around this. The least bogus solution would be to take the physical
address from the first allocation and create a new tag that specified that
further allocations must follow it within that 8MB window, then use that
when allocating new channels, but that's left for anyone else that really
feels like doing it.
Tested by: Erwin Lansing <erwin@lansing.dk>
- `sound'
The generic sound driver, always required.
- `snd_*'
Device-dependent drivers, named after the sound module names.
Configure accordingly to your hardware.
In addition, rename the `snd_pcm' module to `sound' in order to sync
with the driver names.
Suggested by: cg
exactly as done in the cmi driver. I am quite confident this is
safe since I'm runing this for more than two weeks now, on an SMP
box. A few people tested this patch for me successfully as well.
of you with other cards, please do review and test the drivers for
MP-safety and disable Giant in the interrupt routines when you are
sure of proper functionality.
because they bogusly check for defined(INTR_MPSAFE) -- something which
never was a #define. Correct the definitions.
This make INTR_TYPE_AV finally get used instead of the lower-priority
INTR_TYPE_TTY, so it's quite possible some improvement will be had
on sound driver performance. It would also make all the drivers
marked INTR_MPSAFE actually run without Giant (which does seem to
work for me), but:
INTR_MPSAFE HAS BEEN REMOVED FROM EVERY SOUND DRIVER!
It needs to be re-added on a case-by-case basis since there is no one
who will vouch for which sound drivers, if any, willy actually operate
correctly without Giant, since there hasn't been testing because of
this bug disabling INTR_MPSAFE.
Found by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
read-only. Need to enable "legacy support", by poking
into pci config space. (comment from the patch)
Submited by: Autrijus Tang <autrijus@autrijus.org>
Approved by: tanimura (mentor)
This change has not been tested.
This change was triggered by a gcc(1) warning on ia64 at -O2. The
variable v was not used after being computed, which resulted in enough
dead code elimination (DCE) to confuse the compiler and emit a bogus
warning about the use of the variable i without prior definition. The
variable i is the loop variable.
Submitted by: des
Responsibility: marcel
