The reference counts are there to block detach until the sleepers in
read/write/ioctl have gotten out, not to prevent the open device from
going away. Restore the old behavior so that we have a chance to wake
up sleepers when the usb device goes away, so they can properly return
EIO back to the caller when this happens.
Otherwise, we have a guarnateed panic waiting to happen when a device
detaches with an active read channel.
This should be merged to 5 asap.
and was propagated to nearly every platform. The boundary of the child needs
to consider the boundary of the parent and pick the minimum of the two, not
the maximum. However, if either is 0 then pick the appropriate one.
This bug was exposed by a recent change to ATA, which should now be fixed by
this change. The alignment and maxsegsz tag attributes likely also need
a similar review in the near future.
This is a MT5 candidate.
Reviewed by: marcel
Submitted by: sos (in part)
to avoid ABI changes. It is set to the last time the interface
counters were zeroed, currently the time if_attach() was called. It is
intentended to be a valid value for RFC2233's ifCounterDiscontinuityTime
and to make it easier for applications to verify that the interface they
find at a given index is the one that was there last time they looked.
Due to space constraints ifi_epoch is a time_t rather then a struct
timeval. SNMP would prefer higher precision, but this unlikely to be
useful in practice.
the alignment and boundary constraints are being respected, which
fixes the reported ATA problems with SiI chips.
I consider the busdma implementation worrisome nonetheless. Not
only is there too much MI code duplicated in MD files, there's a
lot of questionable code. I smell a wholesale, cross-platform
overhaul coming...
MT5 candidate.
It can be switched back once 5.3 is tested and released. Also turn on
PREEMPTION as many of the stability problems with it have been fixed.
MT5: 3 days.
would turn off all fans when initializing a zone. However, the HP Omnibook
500 generates a notify saying the zone needs to be re-evaluated whenever
its fan is switched on or off. This produced an infinite loop. Also, note
that running _SCP can generate the same notify.
Since we need to make sure old fan references are turned off when getting
new ones, run acpi_tz_monitor() first. This will turn off any unneeded
fans. Then, check for new settings. After that, run acpi_tz_monitor()
again to turn on/off any fans referenced by the new settings.
Tested by: brooks
returned and then infer the state from calls to _ON/_OFF. This works
around a problem in systems that don't correctly report the state (i.e.
the HP Omnibook 500 reports "on" for its fan always after it has been
turned on once).
field.
Replace three instances of longhaired initialization va_filerev fields.
Added XXX comment wondering why we don't use random bits instead of
uptime of the system for this purpose.
I was unable to test this as the PAE kernel crashed with a "cannot copy
LDT" before coming up. When this gets a bit more testing, I'll fix the PAE
conf file to allow isp devices.
PR: 59728
loss links, and 1 second appeared to be too small for high latency links.
If we will receive more complaints, we should make this parameter configurable.
PR: kern/69536
Approved by: archie, julian (mentor)
MFC after: 3 days
happens when a proc exits, but needs to inform the user that this has
happened.. This also means we can remove the check for detached from
proc and sig f_detach functions as this is doing in kqueue now...
MFC after: 5 days
and you botch a call to nmount(2).
This is because there is an INVARIANTS check that asserts that
opt->len must be zero if opt->val is not NULL. The problem is that
the code does not actually follow this invariant if there is an
error while processing mount options.
Fix the code to honor the INVARIANT.
Silence on: fs@
sectorsize in order to avoid a lot of checks around various divisions etc.
Enforce the sectorsize being > 0 with a KASSERT on successful open.
Fix scsi_cd.c to return 2k sectors when no media inserted.
the flags field will be improperly initialized resulting in inconsistent
operation (sometimes with Giant, sometimes without, et al).
RELENG_5 candidate.
state test as well as set, or we risk a race between a socket wakeup
and registering for select() or poll() on the socket. This does
increase the cost of the poll operation, but can probably be optimized
some in the future.
This appears to correct poll() "wedges" experienced with X11 on SMP
systems with highly interactive applications, and might affect a plethora
of other select() driven applications.
RELENG_5 candidate.
Problem reported by: Maxim Maximov <mcsi at mcsi dot pp dot ru>
Debugged with help of: dwhite
cd9660_readdir() to return the address of the file's first data block as
the inode number instead of the address of the directory entry, but
neglected to update cd9660_vget_internal() for the new inode numbering
scheme.
Since the NFS server calls VFS_VGET (cd9660_vget()) with inode numbers
returned through VOP_READDIR (cd9660_readdir()) when servicing a READDIRPLUS
request, these two interfaces must agree on the numbering scheme; failure to
do so caused panics and/or bogus information about the entries to be returned
to clients using READDIRPLUS (Solaris, FreeBSD w/ mount -o rdirplus).
PR: 63446
to RS232 bridges, such as the one found in the DeLorme Earthmate USB GPS
receiver (which is the only device currently supported by this driver).
While other USB to serial drivers in the tree rely heavily on ucom, this
one is self-contained. The reason for that is that ucom assumes that
the bridge uses bulk pipes for I/O, while the Cypress parts actually
register as human interface devices and use HID reports for configuration
and I/O.
The driver is not entirely complete: there is no support yet for flow
control, and output doesn't seem to work, though I don't know if that is
because of a bug in the code, or simply because the Earthmate is a read-
only device.
but with slightly cleaned up interfaces.
The KSE structure has become the same as the "per thread scheduler
private data" structure. In order to not make the diffs too great
one is #defined as the other at this time.
The KSE (or td_sched) structure is now allocated per thread and has no
allocation code of its own.
Concurrency for a KSEGRP is now kept track of via a simple pair of counters
rather than using KSE structures as tokens.
Since the KSE structure is different in each scheduler, kern_switch.c
is now included at the end of each scheduler. Nothing outside the
scheduler knows the contents of the KSE (aka td_sched) structure.
The fields in the ksegrp structure that are to do with the scheduler's
queueing mechanisms are now moved to the kg_sched structure.
(per ksegrp scheduler private data structure). In other words how the
scheduler queues and keeps track of threads is no-one's business except
the scheduler's. This should allow people to write experimental
schedulers with completely different internal structuring.
A scheduler call sched_set_concurrency(kg, N) has been added that
notifies teh scheduler that no more than N threads from that ksegrp
should be allowed to be on concurrently scheduled. This is also
used to enforce 'fainess' at this time so that a ksegrp with
10000 threads can not swamp a the run queue and force out a process
with 1 thread, since the current code will not set the concurrency above
NCPU, and both schedulers will not allow more than that many
onto the system run queue at a time. Each scheduler should eventualy develop
their own methods to do this now that they are effectively separated.
Rejig libthr's kernel interface to follow the same code paths as
linkse for scope system threads. This has slightly hurt libthr's performance
but I will work to recover as much of it as I can.
Thread exit code has been cleaned up greatly.
exit and exec code now transitions a process back to
'standard non-threaded mode' before taking the next step.
Reviewed by: scottl, peter
MFC after: 1 week
write and zero-fill faults to run without holding Giant. It is still
possible to disable Giant-free operation by setting debug.mpsafevm to 0 in
loader.conf.
This essentially merges revs 1.143-1.1445 of sys/pci/if_rl.c.
This now marks the interrupt MPSAFE along with making the mutex non-recursive.
Looked over by: bms
