Since all callers either passed 0 or 1 for clear_ret, define bit 0 in
the flags for use as clear_ret. Reserve bits 1, 2 and 3 for use by MI
code for possible (but unlikely) future use. The remaining bits are for
use by MD code.
This change is triggered by a need on ia64 to have another knob for
get_mcontext().
in the log message for kern_sched.c 1.83 (which should have been
repo-copied to preserve history for this file), the (4BSD) scheduler
algorithm only works right if stathz is nearly 128 Hz. The old
commit lock said 64 Hz; the scheduler actually wants nearly 16 Hz
but there was a scale factor of 4 to give the requirement of 64 Hz,
and rev.1.83 changed the scale factor so that the requirement became
128 Hz. The change of the scale factor was incomplete in the SMP
case. Then scheduling ticks are provided by smp_ncpu CPUs, and the
scheduler cannot tell the difference between this and 1 CPU providing
scheduling ticks smp_ncpu times faster, so we need another scale
factor of smp_ncp or an algorithm change.
This quick fix uses the scale factor without even trying to optimize
the runtime divisions required for this as is done for the other
scale factor.
The main algorithmic problem is the clamp on the scheduling tick counts.
This was 295; it is now approximately 295 * smp_ncpu. When the limit
is reached, threads get free timeslices and scheduling becomes very
unfair to the threads that don't hit the limit. The limit can be
reached and maintained in the worst case if the load average is larger
than (limit / effective_stathz - 1) / 2 = 0.65 now (was just 0.08 with
2 CPUs before this change), so there are algorithmic problems even for
a load average of 1. Fortunately, the worst case isn't common enough
for the problem to be very noticeable (it is mainly for niced CPU hogs
competing with less nice CPU hogs).
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
whether or not the isr needs to hold Giant when running; Giant-less
operation is also controlled by the setting of debug_mpsafenet
o mark all netisr's except NETISR_IP as needing Giant
o add a GIANT_REQUIRED assertion to the top of netisr's that need Giant
o pickup Giant (when debug_mpsafenet is 1) inside ip_input before
calling up with a packet
o change netisr handling so swi_net runs w/o Giant; instead we grab
Giant before invoking handlers based on whether the handler needs Giant
o change netisr handling so that netisr's that are marked MPSAFE may
have multiple instances active at a time
o add netisr statistics for packets dropped because the isr is inactive
Supported by: FreeBSD Foundation
since there is no direct association between M:N thread and kse,
sometimes, a thread does not have a kse, in that case, return a pctcpu
from its last kse, it is not perfect, but gives a good number to be
displayed.
Instead, let the vm objects be lazily instantiated at fault time. This
results in the allocation of fewer vm objects and vm map entries due to
aggregation in the vm system.
o move it from subr_bus.c to netisr.c where it more properly belongs
o add NET_PICKUP_GIANT and NET_DROP_GIANT macros that will be used to
grab Giant as needed when MPSAFE operation is enabled
Supported by: FreeBSD Foundation
Introduce two new macros MNT_ILOCK(mp)/MNT_IUNLOCK(mp) to
operate on this mutex transparently.
Eventually new mutex will be protecting more fields in
struct mount, not only vnode list.
Discussed with: jeff
1.36 +73 -60 src/sys/compat/linux/linux_ipc.c
1.83 +102 -48 src/sys/kern/sysv_shm.c
1.8 +4 -0 src/sys/sys/syscallsubr.h
That change was intended to support vmware3, but
wantrem parameter is useless because vmware3 uses SYSV shared memory
to talk with X server and X server is native application.
The patch worked because check for wantrem was not valid
(wantrem and SHMSEG_REMOVED was never checked for SHMSEG_ALLOCATED segments).
Add kern.ipc.shm_allow_removed (integer, rw) sysctl (default 0) which when set
to 1 allows to return removed segments in
shm_find_segment_by_shmid() and shm_find_segment_by_shmidx().
MFC after: 1 week
waitrunningbufspace() calls so that they are always able to
proceed and clean up buffer space.
Submitted by: Brian Fundakowski Feldman <green@freebsd.org>
Use zpfind() to see if the process became a zombie if pfind() doesn't find it
and if the caller wants to know about process death, so that the caller knows
the process died even if it happened before the kevent was actually registered.
MFC after: 1 week
This fixes a race condition (specifically with signal events) that could
lead to the kn being re-inserted into the list after it has been destroyed,
which is not something we want to happen.
PR: kern/58258
let the MD code choose whether or not to implement such a policy. The new
i386 interrupt code allows multiple FAST handlers for a given source for
example. However, the code does not allow FAST and non-FAST handlers to be
mixed.
idle. They figure out that we're idle fast enough that the cache pollution
introduces by scanning their run queue is more expensive than waiting
a little longer.
- Add kseq_setidle() to mark us as being idle. Use this in place of
kseq_find().
- Remove kseq_load_highest(), kseq_find() was the only consumer of this
interface. kseq_balance() has it's own customized version that finds the
lowest and highest loads simultaneously.
Continuously told that this would be faster by: terry
the total load, the timeshare load, and the number of threads that can
be migrated to another cpu. Account for these seperately.
- Introduce a KSE_CAN_MIGRATE() macro which determines whether or not a KSE
can be migrated to another CPU. Currently, this only checks to see if
we're an interrupt handler. Eventually this will also be used to support
CPU binding.
wasn't curthread, i.e. when we receive a thread pointer to use
as a function argument. Use VOP_UNLOCK/vrele in these cases.
The only case there td != curthread known at the moment is
boot() calling sync with thread0 pointer.
This fixes the panic on shutdown people have reported.
slice assignment. Add a comment describing what it does.
- Remove a stale XXX comment, the nice should not impact the interactivity,
nice adjustments only effect non-interactive tasks in ULE.
- Don't allow nice -20 tasks to totally starve nice 0 tasks. Give them at
least SCHED_SLICE_MIN ticks. We still allow nice 0 tasks to starve nice
+20 tasks as intended.
- SCHED_PRI_NRESV does not have the off by one error in PRIO_TOTAL so we
do not have to account for it in the few places that we use it.
Requested by: bde
0 and SCHED_SLP_RUN_MAX * 2. This allows us to simplify the algorithm
quite a bit. Before, it dealt with arbitrary values which required us
to do nasty integer division tricks that didn't quite work out correctly.
- Chnage sched_wakeup() to detect conditions where the slp+runtime could
exceed SCHED_SLP_RUN_MAX * 2. This can happen if we go to sleep for
longer than 6 seconds. In this case, we'll just clear the runtime and
set the sleep time to the max.
- Define a new function, sched_interact_fork() which updates the slp+runtime
of a newly forked thread. We want to limit the amount of history retained
from the parent so that we learn the child's behavior quickly. We don't,
however want to decay it to nothing. Previously, we would simply divide
each parameter by 100 whenever we forked. After a few forks the values
would reach 0 and tasks would not be considered interactive.
- Add another KTR entry, cleanup some existing entries.
- Remove a useless sched_interact_update() from sched_priority(). This is
already done by the callers that require it.
- Add an IPI based mechanism for migrating kses. This mechanism is
broken down into several components. This is intended to reduce cache
thrashing by eliminating most cases where one cpu touches another's
run queues.
- kseq_notify() appends a kse to a lockless singly linked list and
conditionally sends an IPI to the target processor. Right now this is
protected by sched_lock but at some point I'd like to get rid of the
global lock. This is why I used something more complicated than a
standard queue.
- kseq_assign() processes our list of kses that have been assigned to us
by other processors. This simply calls sched_add() for each item on the
list after clearing the new KEF_ASSIGNED flag. This flag is used to
indicate that we have been appeneded to the assigned queue but not
added to the run queue yet.
- In sched_add(), instead of adding a KSE to another processor's queue we
use kse_notify() so that we don't touch their queue. Also in sched_add(),
if KEF_ASSIGNED is already set return immediately. This can happen if
a thread is removed and readded so that the priority is recorded properly.
- In sched_rem() return immediately if KEF_ASSIGNED is set. All callers
immediately readd simply to adjust priorites etc.
- In sched_choose(), if we're running an IDLE task or the per cpu idle thread
set our cpumask bit in 'kseq_idle' so that other processors may know that
we are idle. Before this, make a single pass through the run queues of
other processors so that we may find work more immediately if it is
available.
- In sched_runnable(), don't scan each processor's run queue, they will IPI
us if they have work for us to do.
- In sched_add(), if we're adding a thread that can be migrated and we have
plenty of work to do, try to migrate the thread to an idle kseq.
- Simplify the logic in sched_prio() and take the KEF_ASSIGNED flag into
consideration.
- No longer use kseq_choose() to steal threads, it can lose it's last
argument.
- Create a new function runq_steal() which operates like runq_choose() but
skips threads based on some criteria. Currently it will not steal
PRI_ITHD threads. In the future this will be used for CPU binding.
- Create a kseq_steal() that checks each run queue with runq_steal(), use
kseq_steal() in the places where we used kseq_choose() to steal with
before.
clobbers this variable. Long ago, when the idle loop wasn't in a
process, it set switchtime.tv_sec to zero to indicate that the time
needs to be read after the idle loop finishes. The special case for
this isn't needed now that there is an idle process (for each CPU).
The time is read in the normal way when the idle process is switched
away from. The seconds component of the time is only zero for the
first second after the uptime is set, and the mostly-dead code was only
executed during this time. (This was slightly broken by using uptimes
instead of times relative to the Epoch -- in the original version the
seconds component of the time was only 0 for the first second after
the Epoch.)
In mi_switch(), moved the setting of switchticks to just after the
first (and now only) setting of switchtime. This setting used to be
delayed since a late setting was needed for the idle case and an early
setting was not needed. Now the early setting is needed so that
fork_exit() doesn't need to set either switchtime or switchticks.
Removed now-completely-rotted comment attached to this. Most of the
code described by the comment had already moved to sched_switch().
begin with sched_lock held but not recursed, so this variable was
always 0.
Removed fixup of sched_lock.mtx_recurse after context switches in
sched_switch(). Context switches always end with this variable in the
same state that it began in, so there is no need to fix it up. Only
sched_lock.mtx_lock really needs a fixup.
Replaced fixup of sched_lock.mtx_recurse in fork_exit() by an assertion
that sched_lock is owned and not recursed after it is fixed up. This
assertion much match the one in mi_switch(), and if sched_lock were
recursed then a non-null fixup of sched_lock.mtx_recurse would probably
be needed again, unlike in sched_switch(), since fork_exit() doesn't
return to its caller in the normal way.
with an mbuf until it is reclaimed. This is in contrast to tags that
vanish when an mbuf chain passes through an interface. Persistent tags
are used, for example, by MAC labels.
Add an m_tag_delete_nonpersistent function to strip non-persistent tags
from mbufs and use it to strip such tags from packets as they pass through
the loopback interface and when turned around by icmp. This fixes problems
with "tag leakage".
Pointed out by: Jonathan Stone
Reviewed by: Robert Watson
Contributed by: Thomaswuerfl@gmx.de
- In sched_prio(), adjust the run queue for threads which may need to move
to the current queue due to priority propagation .
- In sched_switch(), fix style bug introduced when the KSE support went in.
Columns are 80 chars wide, not 90.
- In sched_switch(), Fix the comparison in the idle case and explicitly
re-initialize the runq in the not propagated case.
- Remove dead code in sched_clock().
- In sched_clock(), If we're an IDLE class td set NEEDRESCHED so that threads
that have become runnable will get a chance to.
- In sched_runnable(), if we're not the IDLETD, we should not consider
curthread when examining the load. This mimics the 4BSD behavior of
returning 0 when the only runnable thread is running.
- In sched_userret(), remove the code for setting NEEDRESCHED entirely.
This is not necessary and is not implemented in 4BSD.
- Use the correct comparison in sched_add() when checking to see if an idle
prio task has had it's priority temporarily elevated.
if we do acquire an advisory lock, great! We'll release it later.
However, if we fail to acquire a lock, we perform the coredump
anyway. This problem became particularly visible with NFS after
the introduction of rpc.lockd: if the lock manager isn't running,
then locking calls will fail, aborting the core dump (resulting in
a zero-byte dump file).
Reported by: Yogeshwar Shenoy <ynshenoy@alumni.cs.ucsb.edu>
