the driver to issue a bus reset more quickly than intended. We want to
*wait* if we find another SCB that could be the cause of this timeout,
not proceed to a bus reset.
Noticed by: kan
The ISA probe uses an identify routine to probe all slot locations from
1 to 14 that do not conflict with other allocated resources. This required
making aic7770.c part of the driver core when compiled as a module.
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
Use aic_scb_timer_start() consistently to start the watchdog timer.
This removes a few places that verbatum copied the code in
aic_scb_timer_start().
During recovery processing, allow commands to still be queued to
the controller. The only requirement we have is that our recovery
command be queued first - something the code already guaranteed.
The only other change required to make this work is to prevent
timers from being started for these newly queued commands.
Approved by: re
code was adjusting twice for the instruction pointer indicating
the *next* instruction to execute. The aic79xx driver had a similar
bug, but was fixed some time ago.
by a transaction performing a driver handled message sequence (an
scb with the MK_MESSAGE flag set).
SCBs that perform host managed messaging must always be
at the head of their per-target selection queue so that
the firmware knows to manually assert ATN if the current
negotiation agreement is packetized. In the past we
guaranteed this by queuing these SCBs separarately in
the execution queue. This exposes the system to potential
command reordering in two cases:
1) Another SCB for the same ITL nexus is queued that does
not have the MK_MESSAGE flag set. This SCB will be
queued to the per-target list which can be serviced
before the MK_MESSAGE scb that preceeded it.
2) If the target cannot accept all of the commands in the
per-target selection queue in one selection, the remainder
is queued to the tail of the selection queues so as to
effect round-robin scheduling. This could allow the
MK_MESSAGE scb to be sent to the target before the
requeued commands.
This commit changes the firmware policy to defer queuing
MK_MESSAGE SCBs into the selection queues until this can
be done without affecting order. This means that the
target's selection queue is either empty, or the last
SCB on the execution queue is also a MK_MESSAGE SCB.
During any wait, the firmware halts the download of new
SCBs so only a single "holding location" is required.
Luckily, MK_MESSAGE SCBs are rare and typically occur only
during CAM's bus probe where only one command is outstanding
at a time. However, during some recovery scenarios, the
reordering *could* occur.
aic79xx.c:
Update ahd_search_qinfifo() and helper routines to
search for pending MK_MESSAGE scbs and properly
restitch the execution queue if either the MK_MESSAGE
SCB is being aborted, or the MK_MESSAGE SCB can be
queued due to the execution queue draining due to
aborts.
Enable LQOBUSFREE status to assert an interrupt.
This should be redundant since a BUSFREE interrupt
should always occur along with an LQOBUSFREE event,
but on the Rev A, this doesn't seem to be guaranteed.
When a PPR request is rejected when a previously
existing packetized agreement is in place, assume
that the target has been reset without our knowledge
and revert to async/narrow transfers. This corrects
two issues: the stale ENATNO setting that was used
to send the PPR is cleared so the firmware is not
confused by a future packetized selection with
ATN asserted but no MK_MESSAGE flag in the SCB and
it speeds up recovery by aborting any pending
packetized transactions that by definition are now
dead.
When re-queueing SCBs after a failed negotiation
attempt, ensure command ordering by freezing the
device queue first.
Traverse the list of pending SCBs rather than the
whole SCB array on the controller when pushing
MK_MESSAGE flag changes out to the controller.
The original code was optimized for the aic7xxx
controllers where there are fewer controller slots
then pending SCBs and the firmware picks SCB
slots. For the U320 controller, the hope is
that we have fewer pending SCBs then the 512
slots on the controller.
Enhance some diagnostics.
Factor out some common code.
aic79xx.h:
Add prototype for new ahd_done_with_status() that is
used to factor out some commone code.
aic79xx.reg:
Add definisions for the pending MK_MESSAGE SCB.
aic79xx.seq:
Defer MK_MESSAGE SCB queing to the execution queue
so as to preserve command ordering. Re-arrange some
of the selection processing code so the above change
had no performance impact on the common code path.
Close a few critical section holes.
When entering a non-packetized phase, manually enable
busfree interrupts, since the controller hardware
does not do this automatically.
aic79xx_inline.h:
Enhance logging for queued SCBs.
aic79xx_osm.c:
Add new a new DDB ahd command, ahd_dump, which
invokes the ahd_dump_card_state() routine on the
unit specified with the ahd_sunit DDB command.
aic79xx_pci.c:
Turn on the BUSFREEREV bug for the Rev B. controller.
This is required to close the busfree during non-packetized
phase hole.
for unknown events.
A number of modules return EINVAL in this instance, and I have left
those alone for now and instead taught MOD_QUIESCE to accept this
as "didn't do anything".
Allow 500us between pauses in ahd_pause_and_flushwork().
The maximum we will wait is now 500ms.
In the same routine, remove any attempt to clear ENSELO.
Let the firmware do it once the current selection has
completed. This avoids some race conditions having to
do with non-packetized completions and the auto-clearing
of ENSELO on packetized completions.
Also avoid attempts to clear critical sections when
interrups are pending. We are going to loop again
anyway, so clearing critical sections is a waste of
time. It also may not be possible to clear a critical
section if the source of the interrupt was a SEQINT.
aic79xx_pci.c:
Use the Generic 9005 mask when looking for generic 7901B
parts. This allows the driver to attach to 7901B parts
on motherboards using a non-Adaptec subvendor ID.
aic79xx_inline.h:
Test for the SCBRAM_RD_BUG against the bugs
field, not the flags field in the softc.
aic79xx.c:
Cancel pending transactions on devices that
respond with a selection timeout. This decreases
the duration of timeout recovery when a device
disappears.
aic79xx.c:
Don't bother forcing renegotiation on a selection
timeout now that we use the device reset handler
to abort any pending commands on the target.
The device reset handler already takes us down
to async narrow and forces a renegotiation.
In the device reset handlers, only send a
BDR sent async event if the status is not
CAM_SEL_TIMEOUT. This avoids sending this
event in the selection timeout case
aic79xx.c:
Modify the Core timeout handler to verify that another
command has the potential to timeout before passing off
a command timeout as due to some other command. This
safety measure is added in response to a timeout recovery
failure on H2B where it appears that incoming reselection
status was lost during a drive pull test. In that case,
the recovery handler continued to wait for the command
that was active on the bus indefinetly. While the root
cause of the above issue is still being determined seems
a prudent safeguard.
aic79xx_pci.c:
Add a specific probe entry for the Dell OEM 39320(B).
aic79xx.c:
aic79xx.h:
aic79xx.reg:
aic79xx.seq:
Modify the aic79xx firmware to never cross a cacheline or
ADB boundary when DMA'ing completion entries to the host.
In PCI mode, at least in 32/33 configurations, the SCB
DMA engine may lose its place in the data-stream should
the target force a retry on something other than an
8byte aligned boundary. In PCI-X mode, we do this to
avoid split transactions since many chipsets seem to be
unable to format proper split completions to continue
the data transfer.
The above change allows us to drop our completion entries
from 8 bytes to 4. We were using 8 byte entries to ensure
that PCI retries could only occur on an 8byte aligned
boundary. Now that the sequencer guarantees this by splitting
up completions, we can safely drop the size to 4 bytes (2
byte tag, one byte SG_RESID, one byte pad).
Both the split-completion and PCI retry problems only show
up under high tag load when interrupt coalescing is being
especially effective. The switch from a 2byte completion
entry to an 8 byte entry to solve the PCI problem increased
the chance of incurring a split in PCI-X mode when multiple
transactions were completed at once. Dropping the completion
size to 4 bytes also means that we can complete more commands
in a single DMA (128byte FIFO -> 32 commands instead of 16).
aic79xx.c:
Modify the SCSIINT handler to defer clearing
sequencer critical sections to the individual
interrupt handlers. This allows us to
immediately disable any outgoing selections in
the case of an unexpected busfree so we don't
inadvertantly clear ENSELO *after* a new selection
has started. Doing so may cause the sequencer
to miss a successful selection.
In ahd_update_pending_scbs(), only clear ENSELO if
the bus is currently busy and a selection is not
already in progress or the sequencer has yet to
handle a pending selection. While we want to ensure
that the selection for the SCB at the head of the
selection queue is restarted so that any change in
negotiation request can take effect, we can't clobber
pending selection state without confusing the sequencer
into missing a selection.
sequencer interrupt codes. These codes are only
relevant to the code that was last being executed
and that context is cleared when we reset the
program counter. This addresses a race condition
between a sequencer interrupt and any SCSI event
that causes us to restart the sequencer.
o When running the untagged-Q, we must start the
timer for any transaction we queue.
o Give the firmware half a millisecond between
pauses to flush work out. This should give us
around half a second of total delay before flagging
an issue with pausing and flushing controller work.
Only attempt to clear critical sections if there
are no pending interrupts in the pause and flush
loop. If the sequencer has issued an INTSTAT, we
may not be able to step out of the critical section.
o Cancel pending transactions on devices that
respond with a selection timeout. This decreases
the duration of timeout recovery when a device
disappears.
Don't bother forcing renegotiation on a selection
timeout now that we use the device reset handler
to abort any pending commands on the target.
The device reset handler already takes us down
to async narrow and forces a renegotiation.
o In the device reset handlers, only send a
BDR sent async event if the status is not
CAM_SEL_TIMEOUT. This avoids sending this
event in the selection timeout case.
o Modify the Core timeout handler to verify that another
command has the potential to timeout before passing off
a command timeout as due to some other command.
to build the kernel. It doesn't affect the operation if gcc.
Most of the changes are just adding __INTEL_COMPILER to #ifdef's, as
icc v8 may define __GNUC__ some parts may look strange but are
necessary.
Additional changes:
- in_cksum.[ch]:
* use a generic C version instead of the assembly version in the !gcc
case (ASM code breaks with the optimizations icc does)
-> no bad checksums with an icc compiled kernel
Help from: andre, grehan, das
Stolen from: alpha version via ppc version
The entire checksum code should IMHO be replaced with the DragonFly
version (because it isn't guaranteed future revisions of gcc will
include similar optimizations) as in:
---snip---
Revision Changes Path
1.12 +1 -0 src/sys/conf/files.i386
1.4 +142 -558 src/sys/i386/i386/in_cksum.c
1.5 +33 -69 src/sys/i386/include/in_cksum.h
1.5 +2 -0 src/sys/netinet/igmp.c
1.6 +0 -1 src/sys/netinet/in.h
1.6 +2 -0 src/sys/netinet/ip_icmp.c
1.4 +3 -4 src/contrib/ipfilter/ip_compat.h
1.3 +1 -2 src/sbin/natd/icmp.c
1.4 +0 -1 src/sbin/natd/natd.c
1.48 +1 -0 src/sys/conf/files
1.2 +0 -1 src/sys/conf/files.amd64
1.13 +0 -1 src/sys/conf/files.i386
1.5 +0 -1 src/sys/conf/files.pc98
1.7 +1 -1 src/sys/contrib/ipfilter/netinet/fil.c
1.10 +2 -3 src/sys/contrib/ipfilter/netinet/ip_compat.h
1.10 +1 -1 src/sys/contrib/ipfilter/netinet/ip_fil.c
1.7 +1 -1 src/sys/dev/netif/txp/if_txp.c
1.7 +1 -1 src/sys/net/ip_mroute/ip_mroute.c
1.7 +1 -2 src/sys/net/ipfw/ip_fw2.c
1.6 +1 -2 src/sys/netinet/igmp.c
1.4 +158 -116 src/sys/netinet/in_cksum.c
1.6 +1 -1 src/sys/netinet/ip_gre.c
1.7 +1 -2 src/sys/netinet/ip_icmp.c
1.10 +1 -1 src/sys/netinet/ip_input.c
1.10 +1 -2 src/sys/netinet/ip_output.c
1.13 +1 -2 src/sys/netinet/tcp_input.c
1.9 +1 -2 src/sys/netinet/tcp_output.c
1.10 +1 -1 src/sys/netinet/tcp_subr.c
1.10 +1 -1 src/sys/netinet/tcp_syncache.c
1.9 +1 -2 src/sys/netinet/udp_usrreq.c
1.5 +1 -2 src/sys/netinet6/ipsec.c
1.5 +1 -2 src/sys/netproto/ipsec/ipsec.c
1.5 +1 -1 src/sys/netproto/ipsec/ipsec_input.c
1.4 +1 -2 src/sys/netproto/ipsec/ipsec_output.c
and finally remove
sys/i386/i386 in_cksum.c
sys/i386/include in_cksum.h
---snip---
- endian.h:
* DTRT in C++ mode
- quad.h:
* we don't use gcc v1 anymore, remove support for it
Suggested by: bde (long ago)
- assym.h:
* avoid zero-length arrays (remove dependency on a gcc specific
feature)
This change changes the contents of the object file, but as it's
only used to generate some values for a header, and the generator
knows how to handle this, there's no impact in the gcc case.
Explained by: bde
Submitted by: Marius Strobl <marius@alchemy.franken.de>
- aicasm.c:
* minor change to teach it about the way icc spells "-nostdinc"
Not approved by: gibbs (no reply to my mail)
- bump __FreeBSD_version (lang/icc needs to know about the changes)
Incarnations of this patch survive gcc compiles since a loooong time,
I use it on my desktop. An icc compiled kernel works since Nov. 2003
(exceptions: snd_* if used as modules), it survives a build of the
entire ports collection with icc.
Parts of this commit contains suggestions or submissions from
Marius Strobl <marius@alchemy.franken.de>.
Reviewed by: -arch
Submitted by: netchild
Intel C/C++ compiler (lang/icc) to build the kernel.
The icc CPUTYPE CFLAGS use icc v7 syntax, icc v8 moans about them, but
doesn't abort. They also produce CPU specific code (new instructions
of the CPU, not only CPU specific scheduling), so if you get coredumps
with signal 4 (SIGILL, illegal instruction) you've used the wrong
CPUTYPE.
Incarnations of this patch survive gcc compiles and my make universe.
I use it on my desktop.
To use it update share/mk, add
/usr/local/intel/compiler70/ia32/bin (icc v7, works)
or
/usr/local/intel_cc_80/bin (icc v8, doesn't work)
to your PATH, make sure you have a new kernel compile directory
(e.g. MYKERNEL_icc) and run
CFLAGS="-O2 -ip" CC=icc make depend
CFLAGS="-O2 -ip" CC=icc make
in it.
Don't compile with -ipo, the build infrastructure uses ld directly to
link the kernel and the modules, but -ipo needs the link step to be
performed with Intel's linker.
Problems with icc v8:
- panic: npx0 cannot be emulated on an SMP system
- UP: first start of /bin/sh results in a FP exception
Parts of this commit contains suggestions or submissions from
Marius Strobl <marius@alchemy.franken.de>.
Reviewed by: silence on -arch
Submitted by: netchild
aic79xx.seq:
Convert the COMPLETE_DMA_SCB list to an "stailq". This allows us to
safely keep the SCB that is currently being DMA'ed back the host on
the head of the list while processing completions off of the bus. The
newly completed SCBs are appended to the tail of the queue. In the
past, we just dequeued the SCB that was in flight from the list, but
this could result in a lost completion should the host perform certain
types of error recovery that must cancel all in-flight SCB DMA operations.
Switch from using a 16bit completion entry, holding just the tag and the
completion valid bit, to a 64bit completion entry that also contains a
"status packet valid" indicator. This solves two problems:
o The SCB DMA engine on at least Rev B. silicon does not properly deal
with a PCI disconnect that occurs at a non-64bit aligned offset in the
chips "source buffer". When the transfer is resumed, the DMA engine
continues at the correct offset, but may wrap to the head of the buffer
causing duplicate completions to be reported to the host. By using a
completion buffer in host memory that is 64bit aligned and using 64bit
completion entries, such disconnects should only occur at aligned addresses.
This assumes that the host bridge will only disconnect on cache-line
boundaries and that cache-lines are multpiles of 64bits.
o By embedding the status information in the completion entry we can avoid
an extra memory reference to the HSCB for commands that complete without
error.
Use the comparison of a "host freeze count" and a "sequencer freeze count"
to allow the host to process most SCBs that complete with non-zero status
without having to clear critical sections. Instead the host can just pause the
sequencer, performs any necessary cleanup in the waiting for selection list,
increments its freeze count on the controller, and unpauses. This is only
possible because the sequencer defers completions of SCBs with bad status
until after all pending selections have completed. The sequencer then avoids
referencing any data structures the host may touch during completion of the
SCB until the freeze counts match.
aic79xx.c:
Change the strategy for allocating our sentinal HSCB for the QINFIFO. In
the past, this allocation was tacked onto the QOUTFIFO allocation. Now that
the qoutfifo has grown to accomodate larger completion entries, the old
approach will result in a 64byte allocation that costs an extra page of
coherent memory. We now do this extra allocation via ahd_alloc_scbs()
where the "unused space" can be used to allocate "normal" HSCBs.
In our packetized busfree handler, use the ENSELO bit to differentiate
between packetized and non-packetized unexpected busfree events that
occur just after selection, but before the sequencer has had the oportunity
to service the selection.
When cleaning out the waiting for selection list, use the SCSI mode
instead of the command channel mode. The SCB pointer in the command
channel mode may be referenced by the SCB dma engine even while the
sequencer is paused, whereas the SCSI mode SCB pointer is only accessed
by the sequencer.
Print the "complete on qfreeze" sequencer SCB completion list in
ahd_dump_card_state(). This list holds all SCB completions that are deferred
until a pending select-out qfreeze event has taken effect.
aic79xx.h:
Add definitions and structures to handle the new SCB completion scheme.
Add a controller flag that indicates if the controller is in HostRAID
mode.
aic79xx.reg:
Remove macros used for toggling from one data fifo mode to the other.
They have not been in use for some time.
Add scratch ram fields for our new qfreeze count scheme, converting
the complete dma list into an "stailq", and providing for the "complete
on qfreeze" SCB completion list. Some other fields were moved to retain
proper field alignment (alignment >= field size in bytes).
aic79xx.seq:
Add code to our idle loop to:
o Process deferred completions once a qfreeze event has taken full
effect.
o Thaw the queue once the sequencer and host qfreeze counts match.
Generate 64bit completion entries passing the SCB_SGPTR field as the
"good status" indicator. The first bit in this field is only set if
we have a valid status packet to send to the host.
Convert the COMPLETE_DMA_SCB list to an "stailq".
When using "setjmp" to register an idle loop handler, do not combine
the "ret" with the block move to pop the stack address in the same
instruction. At least on the A, this results in a return to the setjmp
caller, not to the new address at the top of the stack. Since we want
the latter (we want the newly registered handler to only be invoked from
the idle loop), we must use a separate ret instruction.
Add a few missing critical sections.
Close a race condition that can occur on Rev A. silicon. If both FIFOs
happen to be allocated before the sequencer has a chance to service the
FIFO that was allocated first, we must take special care to service the
FIFO that is not active on the SCSI bus first. This guarantees that a
FIFO will be freed to handle any snapshot requests for the FIFO that is
still on the bus. Chosing the incorrect FIFO will result in deadlock.
Update comments.
aic79xx_inline.h
Correct the offset calculation for the syncing of our qoutfifo.
Update ahd_check_cmdcmpltqueues() for the larger completion entries.
aic79xx_pci.c:
Attach to HostRAID controllers by default. In the future I may add a
sysctl to modify the behavior, but since FreeBSD does not have any
HostRAID drivers, failing to attach just results in more email and
bug reports for the author.
MFC After: 1week
to each other.
Correct the recovery thread's loop so that it
will terminate properly on shutdown. We also
clear the recovery_thread proc pointer so that
any additional calls to aic_terminate_recovery_thread()
will not attempt to kill a thread that doesn't
exist. Lastly, code the loop so that termination
will still be successfull even if the termination
request occurs just prior to us entering the loop
or while the recovery thread is off recovering
commands.
that would cause an infinite loop any time we
manually flush the good status FIFO. Also make
our loop delay unconditional to ensure we don't
miss any FIFO allocations by the hardware.
ahc_pci.c:
ahd_pci.c:
aic7xxx.c:
aic79xx.c:
aic_osm_lib.c:
aic_osm_lib.h:
Use common OSM routines from aic_osm_lib for bus dma operations,
delay routines, accessing CCBs, byte swapping, etc.
aic7xxx_pci.c:
Provide a better description for the 2915/30LP on attach.
aic7xxx.c:
aic79xx.c:
aic7770.c:
aic79xx_pci.c:
aic7xxx_pci.c:
aic7xxx_93cx6.c:
Move FBSDID behind an ifdef so that these core files will
still compile under other OSes.
aic79xx.h:
aic79xx_pci.c:
aic79xx.seq:
To speed up non-packetized CDB delivery in Rev B, all CDB
acks are "released" to the output sync as soon as the
command phase starts. There is only one problem with this
approach. If the target changes phase before all data are
sent, we have left over acks that can go out on the bus in
a data phase. Due to other chip contraints, this only
happens if the target goes to data-in, but if the acks go
out before we can test SDONE, we'll think that the transfer
has completed successfully. Work around this by taking
advantage of the 400ns or 800ns dead time between command
phase and the REQ of the new phase. If the transfer has
completed successfully, SCSIEN should fall *long* before we
see a phase change. We thus treat any phasemiss that
occurs before SCSIEN falls as an incomplete transfer.
aic79xx.h:
Add the AHD_FAST_CDB_DELIVERY feature.
aic79xx_pci.c:
Set AHD_FAST_CDB_DELIVERY for all Rev. B parts.
aic79xx.seq:
Test for PHASEMIS in the command phase for
all AHD_FAST_CDB_DELIVERY controlelrs.
ahd_pci.c:
ahc_pci.c:
aic7xxx.h:
aic79xx.h:
Move definition of controller BAR offsets to core header files.
aic7xxx.c:
aic79xx.c:
In the softc free routine, leave removal of a softc from the
global list of softcs to the OSM (the caller of this routine).
This allows us to avoid holding the softc list_lock during device
destruction where we may have to sleep waiting for our recovery
thread to halt.
ahc_pci.c:
Use ahc_pci_test_register access to validate I/O mapped in
addition to the tests already performed for memory mapped
access.
Remove unused ahc_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
ahd_pci.c:
Remove reduntant definition of controller BAR offsets. These
are also defined in aic79xx.h.
Remove unused ahd_power_state_change() function. The PCI
layer in both 4.X and 5.X now offer this functionality.
aic7xxx.c:
aic79xx.c:
aic79xx.h:
aic7xxx.h:
aic7xxx_osm.c:
aic79xx_osm.c:
Move timeout handling to the driver cores. In the case
of the aic79xx driver, the algorithm has been enhanced
to try target resets before performing a bus reset. For
the aic7xxx driver, the algorithm is unchanged. Although
the drivers do not currently sleep during recovery (recovery
is timeout driven), the cores do expect all processing to
be performed via a recovery thread. Our timeout handlers
are now little stubs that wakeup the recovery thread.
aic79xx.c:
aic79xx.h:
aic79xx_inline.h:
Change shared_data allocation to use a map_node so
that the sentinel hscb can use this map node in
ahd_swap_with_next_hscb. This routine now swaps
the hscb_map pointer in additon to the hscb
contents so that any sync operations occur on
the correct map.
physaddr -> busaddr
Pointed out by: Jason Thorpe <thorpej@wasabisystems.com>
aic79xx.c:
Make more use of the in/out/w/l/q macros for accessing
byte registers in the chip.
Correct some issues in the ahd_flush_qoutfifo() routine.
o Run the qoutfifo only once the command channel
DMA engine has been halted. This closes a window
where we might have missed some entries.
o Change ahd_run_data_fifo() to not loop to completion.
If we happen to start on the wrong FIFO and the other
FIFO has a snapshot savepointers, we might deadlock.
This required our delay between FIFO tests to be
moved to the ahd_flush_qoutfifo() routine.
o Update/add comments.
o Remove spurious test for COMPLETE_DMA list being empty
when completing transactions from the GSFIFO with
residuals. The SCB must be put on the COMPLETE_DMA
scb list unconditionally.
o When halting command channel DMA activity, we must
disable the DMA channel in all cases but an update
of the QOUTFIFO. The latter case is required so
that the sequencer will update its position in the
QOUTFIFO. Previously, we left the channel enabled
for all "push" DMAs. This left us vulnerable to
the sequencer handling an SCB push long after that
SCB was already processed manually by this routine.
o Correct the polarity of tests involving
ahd_scb_active_in_fifo(). This routine returns
non-zero for true.
Return to processing bad status completions through
the qoutfifo. This reduces the time that the sequencer
is kept paused when handling transactions with bad
status or underruns.
When waiting for the controller to quiece selections,
add a delay to our loop. Otherwise we may fail to wait
long enough for the sequencer to comply.
On H2A4 hardware, use the slow slewrate for non-paced
transfers. This mirrors what the Adaptec Windows
drivers do.
On the Rev B. only slow down the CRC timing for
older U160 devices that might need the slower timing.
We define "older" as devices that do not support
packetized protocol.
Wait up to 5000 * 5us for the SEEPROM to become unbusy.
Write ops seem to take much longer than read ops.
aic79xx.seq:
For controllers with the FAINT_LED bug, turn the diagnostic
led feature on during selection and reselection. This covers
the non-packetized case. The LED will be disabled for
non-packetized transfers once we return to the top level idle
loop. Add more comments about the busy LED workaround.
Extend a critical section around the entire
command channel idle loop process. Previously
the portion of this handler that directly manipulated
the linked list of completed SCBs was not protected.
This is the likely cause of the recent reports of
commands being completed twice by the driver.
Extend critical sections across the test for,
and the longjump to, longjump routines. This
prevents the firmware from trying to jump to
a longjmp handler that was just cleared by the
host.
Improve the locations of several critical section
begin and end points. Typically these changes
remove instructions that did not need to be
inside a critical section.
Close the "busfree after selection, but before busfree
interrupts can be enabled" race to just a single sequencer
instruction. We now test the BSY line explicitly before
clearing the busfree status and enabling the busfree
interrupt.
Close a race condition in the processing of HS_MAILBOX
updates. We now clear the "updated" status before the
copy. This ensures that we don't accidentally clear
the status incorrectly when the host sneaks in an update
just after our last copy, but before we clear the status.
This race has never been observed.
Don't re-enable SCSIEN if we lose the race to disable SCSIEN
in our interrupt handler's workaround for the RevA data-valid
too early issue.
aic79xx_inline.h:
Add comments indicating that the order in which bytes are
read or written in ahd_inw and ahd_outw is important. This
allows us to use these inlines when accessing registers with
side-effects.
aic79xx_pci.c:
The 29320 and the 29320B are 7902 not 7901 based products.
Correct the driver banner.
aic7xxx.h:
Enable the use of the auto-access pause feature
on the aic7870 and aic7880. It was disabled due
to an oversight.
aic7xxx.reg:
Move TARG_IMMEDIATE_SCB to alias LAST_MSG to
avoid leaving garbage in MWI_RESIDUAL. This
prevents spurious overflows whn operating target
mode on controllers that require the MWI_RESIDUAL
work-around.
aic7xxx.seq:
AHC_TMODE_WIDEODD_BUG is a bug, not a softc flag.
Reference the correct softc field when testing
for its presence.
Set the NOT_IDENTIFIED and NO_CDB_SENT bits
in SEQ_FLAGS to indicate that the nexus is
invalid in await busfree.
aic7xxx_93cx6.c:
Add support for the C56/C66 versions of the EWEN and EWDS
commands.
aic7xxx.c:
aic7xxx_pci.c:
Move test for the validity of left over BIOS data
to ahc_test_register_access(). This guarantees that
any left over CHIPRST value is not clobbered by our
register access test and lost to the test that was
in ahc_reset.
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
aic7xxx_pci.c:
When performing our register test, be careful
to avoid resetting the chip when pausing the
controller. The test reads the HCNTRL register
and then writes it back with the PAUSE bit
explicitly set. If the last write to the controller
before our probe is to reset it, the CHIPRST
bit will still be set, so we must mask it off
before the PAUSE operation. On some chip versions,
we cannot access registers for a few 100us after
a reset, so this inadvertant reset was causing PCI
errors to occur on the read to check for paused
status.
Submitted by: gibbs
Add two new arguments to bus_dma_tag_create(): lockfunc and lockfuncarg.
Lockfunc allows a driver to provide a function for managing its locking
semantics while using busdma. At the moment, this is used for the
asynchronous busdma_swi and callback mechanism. Two lockfunc implementations
are provided: busdma_lock_mutex() performs standard mutex operations on the
mutex that is specified from lockfuncarg. dftl_lock() is a panic
implementation and is defaulted to when NULL, NULL are passed to
bus_dma_tag_create(). The only time that NULL, NULL should ever be used is
when the driver ensures that bus_dmamap_load() will not be deferred.
Drivers that do not provide their own locking can pass
busdma_lock_mutex,&Giant args in order to preserve the former behaviour.
sparc64 and powerpc do not provide real busdma_swi functions, so this is
largely a noop on those platforms. The busdma_swi on is64 is not properly
locked yet, so warnings will be emitted on this platform when busdma
callback deferrals happen.
If anyone gets panics or warnings from dflt_lock() being called, please
let me know right away.
Reviewed by: tmm, gibbs
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
of the contents of the CCSCBCTL register into our
local varaible. The other bits are used in later tests.
This avoids a potential deadlock in ahd_run_qoutfifo()
if we happen to catch the DMA engine in just the right
state.
Devices below may experience a change in geometry.
* Due to a bug, aic(4) never used extended geometry. Changes all drives
>1G to now use extended translation.
* sbp(4) drives exactly 1 GB in size now no longer use extended geometry.
* umass(4) drives exactly 1 GB in size now no longer use extended geometry.
For all other controllers in this commit, this should be a no-op.
Looked over by: scottl
if it was already enabled. We don't want to set it
when it shouldn't be set, we just don't want to
inadvertantly turn it off. This should fix a recent
report of the aic7xxx driver repeatedly complaining of
"unexpected busfree while idle" in one configuration.
successfully mapping our registers. This
avoids the disabling of memory mapped I/O
just because some other driver probe happened
to touch our registers.
This drive delays going async after receiving a WDTR
message. We now send an SDTR message after a WDTR even
if our goal is to go async. This should work even for
confused devices.
If we get an unexpected busfree when attempting a WDTR
or SDTR, only set the goal negotiation parameters we were
trying to negotiate to off. This means that should a WDTR
message fail, we will still try an SDTR if our goal is
non-async.
Fix a few more places where we were looking at goal.period
instead of goal.offset for determining if we should be
negotiating sync. This should not have any impact on
our behavior, but the offset is more definitive and should
be used.
