the user requests a read-only mount. This is necessary because we
don't do the VOP_OPEN again if they upgrade a read-only mount to
read-write.
Fixes lockup when creating files on msdosfs mounts that have been
mounted read-only then upgraded to read-write. The exact cause of
the lockup is not known, but it is likely to be the kernel getting
stuck in an infinite loop trying to write dirty buffers to a device
without write permission.
Reported/tested by andreas, discussed with phk.
mapped I/O mode, we pause for .1 seconds after issuing the reset command
before trying to poll the 'command busy' bit in the status register.
With my 3c575C cardbus NIC, my Sony Picturebook locks up when it tries
to read the status register immediately after the reset. This appears
to be a problem only with certain NICs on certain hardware, but the
added delay should not hurt cards that already work.
This bug seems to have been brought to light by the fact that the xl
driver now defaults to memory mapped I/O mode instead of programmed
I/O mode like it used to. With PIO mode, the delay isn't needed and
everything works (which is why this NIC worked with 5.0-RELEASE but
not 5.1). I suspect that what's happening is that when the chip is
reset, it takes a little while for the memory-mapped decoding logic
to recover. Trying to access the chip's registers during this period
causes an error condition of some kind that wedges the system.
1.) Handle maximum segment sizes which are smaller than the IOMMU page
size by splitting up pages across multiple segments if needed; this case
was previously unimplemented, and would cause panics.
2.) KASSERT that the physical address is in range; remove a KASSERT that
has become pointless.
3.) Add a comment describing what remains to be fixed in the IOMMU code;
I plan to address these issues soon.
Desired by: dwhite (1)
happens to work on 32-bit platforms as sizeof(long)=sizeof(int), but
wrecks all kinds of havoc (garbage reads, corrupting writes and
misaligned loads/stores) on 64-bit architectures.
The fix for now is to use fuword32() and suword32() and change the
type of the applicable int fields to int32. This is to make it
explicit that we depend on these fields being 32-bit. We may want
to revisit this later.
Reviewed by: deischen
the VMIN and VTIME members of the c_cc array. These members are not
special control characters. By not excluding these members we
changed the noncanonical mode input processing when both members
were 0 on entry (=LINUX_POSIX_VDISABLE) as we would remap them to 255
(=_POSIX_VDISABLE). See termios(4) case A for how that screws up
your terminal I/O.
PR: 23173
Originator: Bjarne Blichfeldt <bbl@dk.damgaard.com>
Patch by: Boris Nikolaus <bn@dali.tellique.de> (original submission)
Philipp Mergenthaler <philipp.mergenthaler@stud.uni-karlsruhe.de>
Reminders by: Joseph Holland King <gte743n@cad.gatech.edu>
MFC after: 5 days
- Initialize fc->status to process bus reset correctly after resume.
- Initialize AT ring buffer pointer.
- Requeue stdma to stfree for active IR buffer.
- Stop DMA before suspend for safe.
- Set powerstate after resume.
function behaves correctly in principle, but is not expected to be
100% complete. In any case, with this commit we have KSE ported
enough to start runtime testing with threaded applications and fix
whatever bugs or omissions we encounter. Yay!
or unblock a thread in kernel, and allow UTS to specify whether syscall
should be restarted.
o Add ability for UTS to monitor signal comes in and removed from process,
the flag PS_SIGEVENT is used to indicate the events.
o Add a KMF_WAITSIGEVENT for KSE mailbox flag, UTS call kse_release with
this flag set to wait for above signal event.
o For SA based thread, kernel masks all signal in its signal mask, let
UTS to use kse_thr_interrupt interrupt a thread, and install a signal
frame in userland for the thread.
o Add a tm_syncsig in thread mailbox, when a hardware trap occurs,
it is used to deliver synchronous signal to userland, and upcall
is schedule, so UTS can process the synchronous signal for the thread.
Reviewed by: julian (mentor)
POSIX says siginfo pointer parameter can be NULL and if the
function success, it should return signal number but not zero.
The waitset it past should be negatived before it can be
used as thread signal mask.
color in vm_page_alloc(). (This also has small performance benefits.)
- Eliminate vm_page_select_free(); vm_page_alloc() might as well
call vm_pageq_find() directly.
nice distribution without significantly impacting interactive response.
As a side effect it should also allow batch processes to run for a
slightly longer period which will positively impact their performance.
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
to store an int in the bio->bio_driver1 (a void *). It is big enough,
but you have to match the int sizes first before doing the cast.
Glanced at by: scottl
