The offset field in struct dirent was set to the offset of
the next dirent in rev 1.36. The offset was calculated from
the current offset and the record length. This offset does
not necessarily match the real offset when we are using
cookies. Therefore, also use the cookies to set the offset
field in struct dirent if we're using cookies to iterate
through the dirents.
circuit generates too much jitter to be used directly as xmit clock.
Don't miscount pending bytes in weird error conditions.
Drop the rest of a packet if we run out of tx-md's.
Trig the xmit-frame signal on rising edge, this fixed the one-bit-too-late
position of the HDLC frames in E1 mode.
wakeup all of the sleeping threads when we free only one buffer. This
avoids us having to needlessly try again (and fail, and go back to
sleep) for all the threads sleeping. We will now only wakeup the
thread we know will succeed.
Reviewed by: green
only be checked if the system is currently performing New Reno style
fast recovery. However, this value was being checked regardless of the
NR state, with the end result being that the congestion window was never
opened.
Change the logic to check t_dupack instead; the only code path that
allows it to be nonzero at this point is NewReno, so if it is nonzero,
we are in fast recovery mode and should not touch the congestion window.
Tested by: phk
pollution in <sys/mutex.h>. This was half fixed in rev.1.3 of
midwayreg.h. The pollution exposed the bug that this driver was using
toy versions of the bus space macros under FreeBSD. Disabling the
toy versions made this driver compile but dependent on the pollution.
There was still a toy version of bus_space_read_1() in unreachable code.
namespace pollution in <sys/mutex.h>. This was half fixed in rev.1.3
of midwayreg.h. The pollution exposed the bug that this driver was
using toy versions of the bus space macros under FreeBSD. Disabling
the toy versions made this driver compile and maybe support PIO space,
but dependent on the pollution.
ufs_vnops.c:
1) i_ino was confused with i_number, so the inode number passed to
VFS_VGET() was usually wrong (usually 0U).
2) ip was dereferenced after vgone() freed it, so the inode number
passed to VFS_VGET() was sometimes not even wrong.
Bug (1) was usually fatal in ext2_mknod(), since ext2fs doesn't have
space for inode 0 on the disk; ino_to_fsba() subtracts 1 from the
inode number, so inode number 0U gives a way out of bounds array
index. Bug(1) was usually harmless in ufs_mknod(); ino_to_fsba()
doesn't subtract 1, and VFS_VGET() reads suitable garbage (all 0's?)
from the disk for the invalid inode number 0U; ufs_mknod() returns
a wrong vnode, but most callers just vput() it; the correct vnode is
eventually obtained by an implicit VFS_VGET() just like it used to be.
Bug (2) usually doesn't happen.
freelist. Should now be thread-friendly, in part.
Note: More work is needed in uipc_syscalls.c, but it will have to wait until
the socket locking issues are at least 80% implemented and committed.
CDs.
With audio CDs, you can't just do a READ(10) call on most drives without
first setting the blocksize with a mode select command. The disklabel code
does a read of the first sector of the media to find a label if it exists.
This caused drives to return an error when an audio CD was in the drive,
due to the problem described above.
The solution is to read the table of contents on the CD, and only attempt
to read the disklabel if the first track is a data track.
This works on all the various CD and DVD media I have tried, but further
testing (especially with Video CDs and other mode 2 media) will be
needed to determine if this is a universal solution.
When this feature is enabled, mke2fs doesn't necessarily allocate a
super block and its associated descriptor blocks for every group.
The (non-)allocations are reflected in the block bitmap. Since the
filesystem code doesn't write to these blocks except for the first
superblock, all it has to do to support them is to not count them in
ext2_statfs() and not attempt to check them at mount time in
ext2_check_blocks_bitmap() (the check has never been enabled in
FreeBSD anyway).
and nobroadcast bits in the mode register and call it both from
pcn_init() and pcn_ioctl(). Sometimes we need to force the state
of the nobroadcast bit after switching out of promisc mode.
them. If we leave garbage in them, the dc_apply_fixup() routine may
try to follow bogus pointers when applying the reset fixup.
Noticed by: Andrew Gallatin
getnewvnode(). Otherwise routines called from VOP_INACTIVE() might
attempt to remove the vnode from a free list the vnode isn't on,
causing corruption.
PR: 18012
out of fashion. This particular case, unlike joy(8) and friends which
are just plain silly, did more than just load a kernel loadable module.
However, /etc/rc and the linux_base port were adjusted a while back to
cope with the absence of this script.
The only outstanding reason to hang on to it would have been for the
linux(8) manual page, which clued folks into the existence of the
Linuxulator. A new linux(4) was introduced a while back. It does
a much better job.
This script just isn't useful any more.
- Look for a hardwired interrupt in the routing table for this
bus/device/pin (we already did this).
- Look for another device with the same link byte which has a hardwired
interrupt.
- Look for a PCI device matching an entry with the same link byte
which has already been assigned an interrupt, and use that.
- Look for a routable interrupt listed in the "PCI only" interrupts
field and use that.
- Pick the first interrupt that's marked as routable and use that.
Xtal reference instead of the CLADI input.
In unframed E1 mode, tie SIGFRZ low so that the mysycc doesn't
get confused.
Don't mask errors with OOF. Don't ignore OOF errors.
Stop the channel before freeing mbufs in disconnect.
I still have no T1 devices to test with, so the T1 code is non-existent.
argument. These flags include INTR_FAST, INTR_MPSAFE, etc.
- Properly handle INTR_EXCL when it is passed in to allow an interrupt
handler to claim exclusive ownership of an interrupt thread.
- Add support for psuedo-fast interrupts on the alpha. For fast interrupts,
we don't allocate an interrupt thread; instead, during dispatching of an
interrupt, we run the handler directly instead of scheduling the thread
to run. Note that the handler is currently run without Giant and must be
MP safe. The only fast handler currently is for the sio driver.
Requested by: dfr
multicast filter on the Pegasus chip. Since IPv6 depends a lot
on multicasting, this caused several failures for people trying to
use IPv6 with Pegasus USB ethernet devices.
Submitted by: Jun Kuriyama <kuriyama@FreeBSD.org>
Return ENOTSUP for any opcode that is not supported by the XPT
device.
Add back a missing local declaration that seems to have been deleted
by my last commit.
Filter incoming transfer negotiation requests to ensure they
never exceed the settings specified by the user.
In restart sequencer attempt to deal with a bug in the aic7895.
If a third party reset occurs at just the right time, the
stack register can lock up. When restarting the sequencer
after handling the SCSI reset, poke SEQADDR1 before resting
the sequencers program counter.
When something strange happens, dump the card's transaction
state via ahc_dump_card_state(). This should aid in debugging.
Handle request sense transactions via the QINFIFO instead of
attaching them to the waiting queue directly. The waiting
queue consumes card SCB resources and, in the pathological case
of every target on the bus beating our selection attemps and
issuing a check condition, could have caused us to run out
of SCBs. I have never seen this happen, and only early
cards with 3 or 4 SCBs had any real chance of ever getting
into this state.
Add additional sequencer interrupt codes to support firmware
diagnostics. The diagnostic code is enabled with the
AHC_DEBUG_SEQUENCER kernel option.
Make it possible to switch into and out of target mode on
the fly. The card comes up by default as an initiator but
will switch into target mode as soon as an enable lun operation
is performed. As always, target mode behavior is gated
by the AHC_TMODE_ENABLE kernel option so most users will
not be affected by this change.
In ahc_update_target_msg_request(), also issue a new
request if the ppr_options have changed.
Never issue a PPR as a target. It is forbidden by the spec.
Correct a bug in ahc_parse_msg() that prevented us from
responding to PPR messages as a target.
Mark SCBs that are on the untagged queue with a flag instead
of checking several fields in the SCB to see if the SCB should
be on the queue. This makes it easier for things like automatic
request sense requests to be queued without touching the
untagged queues even though they are untagged requests.
When dealing with ignore wide residue messages that occur
in the middle of a transfer, reset HADDR, not SHADDR for
non-ultra2 chips. Although SHADDR is where the firmware
fetches the ending transfer address for a save data pointers
request, it is readonly. Setting HADDR has the side effect
of also updating SHADDR.
Cleanup the output of ahc_dump_card_state() by nulling out the
free scb list in the non-paging case. The free list is only
used if we must page SCBs.
Correct the transmission of cdbs > 12 bytes in length. When
swapping HSCBs prior to notifing the sequencer of the new
transaction, the bus address pointer for the cdb must also
be recalculated to reflect its new location. We now defer
the calculation of the cdb address until just before queing
it to the card.
When pulling transfer negotiation settings out of scratch
ram, convert 5MHz/clock doubled settings to 10MHz.
Add a new function ahc_qinfifo_requeue_tail() for use by
error recovery actions and auto-request sense operations.
These operations always occur when the sequencer is paused,
so we can avoid the extra expense incurred in the normal
SCB queue method.
Use the BMOV instruction for all single byte moves on
controllers that support it. The bmov instruction is
twice as fast as an AND with an immediate of 0xFF as
is used on older controllers.
Correct a few bugs in ahc_dump_card_state(). If we have
hardware assisted queue registers, use them to get the
sequencer's idea of the head of the queue. When enumerating
the untagged queue, it helps to use the correct index for
the queue.
aic7xxx.h:
Indicate via a feature flag, which controllers can take
on both the target and the initiator role at the same time.
Add the AHC_SEQUENCER_DEBUG flag.
Add the SCB_CDB32_PTR flag used for dealing with cdbs
with lengths between 13 and 32 bytes.
Add new prototypes.
aic7xxx.reg:
Allow the SCSIBUSL register to be written to. This is
required to fix a selection timeout problem on the 7892/99.
Cleanup the sequencer interrupt codes so that all debugging
codes are grouped at the end of the list.
Correct the definition of the ULTRA_ENB and DISC_DSB locations
in scratch ram. This prevented the driver from properly honoring
these settings when no serial eeprom was available.
Remove an unused sequencer flag.
aic7xxx.seq:
Just before a potential select-out, clear the SCSIBUSL
register. Occasionally, during a selection timeout, the
contents of the register may be presented on the bus,
causing much confusion.
Add sequencer diagnostic code to detect software and or
hardware bugs. The code attempts to verify most list
operations so any corruption is caught before it occurs.
We also track information about why a particular reconnection
request was rejected.
Don't clobber the digital REQ/ACK filter setting in SXFRCTL0
when clearing the channel.
Fix a target mode bug that would cause us to return busy
status instead of queue full in respnse to a tagged transaction.
Cleanup the overrun case. It turns out that by simply
butting the chip in bitbucket mode, it will ack any
bytes until the phase changes. This drasticaly simplifies
things.
Prior to leaving the data phase, make sure that the S/G
preload queue is empty.
Remove code to place a request sense request on the waiting
queue. This is all handled by the kernel now.
Change the semantics of "findSCB". In the past, findSCB
ensured that a freshly paged in SCB appeared on the disconnected
list. The problem with this is that there is no guarantee that
the paged in SCB is for a disconnected transation. We now
defer any list manipulation to the caller who usually discards
the SCB via the free list.
Inline some busy target table operations.
Add a critical section to protect adding an SCB to
the disconnected list.
aic7xxx_freebsd.c:
Handle changes in the transfer negotiation setting API
to filter incoming requests. No filtering is necessary
for "goal" requests from the XPT.
Set the SCB_CDB32_PTR flag when queing a transaction with
a large cdb.
In ahc_timeout, only take action if the active SCB is
the timedout SCB. This deals with the case of two
transactions to the same device with different timeout
values.
Use ahc_qinfifo_requeu_tail() instead of home grown
version.
aic7xxx_inline.h:
Honor SCB_CDB32_PTR when queuing a new request.
aic7xxx_pci.c:
Use the maximum data fifo threshold for all chips.
The XPT uses this to prevent tags from being used on parallel SCSI
interfaces immediately after a bus reset or BDR so that controllers
have an oportunity to renegotiate without tag messages in the way.
Somehow this got disabled... the functionality has been here for
quite some time.
Noticed by: my SCSI bus analyzer
This removes support for booting current kernels with very old bootblocks.
Device driver writers: Please remove initializations for the d_bmaj
field in your cdevsw{}.
terminated and the data_len field is no longer necessary.
Add ASCII2BINARY and BINARY2ASCII capabilities.
The old format is still understood and dealt with, but can't do
the ASCII2BINARY and BINARY2ASCII stuff.
Approved by: archie
current implementation, jail neither virtualizes the Sys V IPC namespace,
nor provides inter-jail protections on IPC objects.
o Support for System V IPC can be enabled by setting jail.sysvipc_allowed=1
using sysctl.
o This is not the "real fix" which involves virtualizing the System V
IPC namespace, but prevents processes within jail from influencing those
outside of jail when not approved by the administrator.
Reported by: Paulo Fragoso <paulo@nlink.com.br>
in the p_candebug() function. Synchronize with sef's CHECKIO()
macro from the old procfs, which seems to be a good source of security
checks.
Obtained from: TrustedBSD Project
PPTP links are no longer dropped by simple (and inappropriate in this
case) "inactivity timeout" procedure, only when requested through the
control connection.
It is now possible to have multiple PPTP servers running behind NAT.
Just redirect the incoming TCP traffic to port 1723, everything else
is done transparently.
Problems were reported and the fix was tested by:
Michael Adler <Michael.Adler@compaq.com>,
David Andersen <dga@lcs.mit.edu>
This is due to a bug that has been in there since Warneer did the
PCCARD stuff, the altioaddr is not offset 8 its offset 14 from
the base address.
Also only probe the master device, no known PCCARD ATA thingies
has a slave AFAIK..
- Add DRIVER_MODULE() declaration to make this driver a
child of cardbus
- Handle different width EEPROMs
The CIS parser still barfs when scanning this card, but it seems to
probe/attach correctly anyway. I can't do a traffic test just yet
since I don't have a proper crossover cable handy.
This allows writing to DVD-RAM, PD and similar drives that probe as CD
devices. Note that these are randomly writeable devices, not
sequential-only devices like CD-R drives, which are supported by cdrecord.
Add a new flag value for dsopen(), DSO_COMPATLABEL. The cd(4) driver now
uses this flag instead of the DSO_NOLABELS flag. The DSO_NOLABELS always
used a "fake" disklabel for the entire disk, provided by the caller.
With the DSO_COMPATLABEL flag, dsopen() will first search the media for a
label, and if it finds a label, it will use that label. Otherwise it will
use the fake disklabel provided by the caller. This provides backwards
compatibility, since we will still have labels for ISO9660 media.
It also provides new functionality, since you can now have a regular BSD
disklabel on read-only media, or on writeable media (e.g. DVD-RAM).
Bruce and I both think that we should eventually (in a few years) get
away from using disklabels for ISO9660 media, and just use the whole disk
device (/dev/cd0). At that point disklabel handling in the cd(4) driver
could follow the "normal" model, as used in the da(4) driver.
Also, clean up the path in a couple of places in cdregister(). (Thanks to
Nick Hibma for catching that bug.)
Reviewed by: bde
Otherwise, aio_read() and aio_write() on sockets are broken if a kevent is
registered. (The code after kevent registration for handling sockets assumes
that the struct file pointer "fp" still refers to the socket, not the kqueue.)
Don't check for a null pointer if malloc called with M_WAITOK.
Submitted by: josh@zipperup.org
Submitted by: Robert Drehmel <robd@gmx.net>
Approved by: bp
<sys/proc.h> to <sys/systm.h>.
Correctly document the #includes needed in the manpage.
Add one now needed #include of <sys/systm.h>.
Remove the consequent 48 unused #includes of <sys/proc.h>.
the offending inline function (BUF_KERNPROC) on it being #included
already.
I'm not sure BUF_KERNPROC() is even the right thing to do or in the
right place or implemented the right way (inline vs normal function).
Remove consequently unneeded #includes of <sys/proc.h>
used in lower layer (scsi_low.c).
The flag of ncv for KME KXLC004 was chaged from 0x1 to 0x100.
The flag of nsp for PIO mode was chaged from 0x1 to 0x100.
command register is too aggressive. Revert to the previous behaviour, but
leave the new behaviour available as an undocumented option. It's not
clear what the Right, Right Thing is to do here, but the more conservative
approach is safer.
a RealTek 8139 cardbus device. Unfortunately it doesn't quite work yet
because the CIS parser barfs on it.
Submitted by msmith, with some small tweaks by me.
return the last value returned by a nested method call. This violates
the ACPI spec, but is implemented by the Microsoft interpreter, and thus
vendors can (and do) get away with it.
Intel's stance is that this is illegal and should not be supported.
As they put it, however, we have to live in the real world. So go ahead
and implement it.
Submitted by: Mitsaru IWASAKI <iwasaki@jp.freebsd.org>
- Set debugger options for kernel build
- Define some missing functions
- Bring in GCC defines
- Disable the 'wbinvd' macro as it conflicts with our inline
- AcpiGetProcessorID (fetch the ACPI processor ID for a given ACPI_HANDLE)
- AcpiSetSystemSleepState (set the Sx sleeping state, proposed by Intel
but not actually implemented)
ACPICA. Most of these are still works in progress. Support exists for:
- Fixed feature and control method power, lid and sleep buttons.
- Detection of ISA PnP devices using ACPI namespace.
- Detection of PCI root busses using ACPI namespace.
- CPU throttling and sleep states (incomplete)
- Thermal monitoring and cooling control (incomplete)
- Interface to platform embedded controllers (mostly complete)
- ACPI timer (incomplete)
- Simple userland control of sleep states.
- Shutdown and poweroff.
seems to be that the nodes are bzero'd beforehand, but the submitter
found that this was not always the case, and in any event defensive
programming here costs epsilon squared.
PR: 22244
Submitted by: Dave Gillam <daveg@chiaro.com>
because it only takes a struct tag which makes it impossible to
use unions, typedefs etc.
Define __offsetof() in <machine/ansi.h>
Define offsetof() in terms of __offsetof() in <stddef.h> and <sys/types.h>
Remove myriad of local offsetof() definitions.
Remove includes of <stddef.h> in kernel code.
NB: Kernelcode should *never* include from /usr/include !
Make <sys/queue.h> include <machine/ansi.h> to avoid polluting the API.
Deprecate <struct.h> with a warning. The warning turns into an error on
01-12-2000 and the file gets removed entirely on 01-01-2001.
Paritials reviews by: various.
Significant brucifications by: bde
to reinstall boot1 after a 'make world'.
Unfortunately this means that people who have already installed a new
boot1 from a 'make world' after 2000/09/18 *must* reinstall it after
their next build using something like:
# disklabel -B /dev/da0c
