hold a wq lock for the iterator. Panda uses a
silly recursive lock they hold through the timer.
- Add poor mans wireshark compile option..
- Allocate and start using SCTP_M_XXX for all SCTP_MALLOC() calls.
- sysctl now will get back the refcnt for viewing by onlookers.
Reviewed by: gnn
- bounded cookie-life to 1 second minimum in socket option set.
- Delayed_ack_time becomes delayed_ack per new socket api document.
- Improve port number selection, we now use low/high bounds and
no chance of a endless loop. Only one call to random per bind
as well.
- fixes so set_peer_primary pre-screens addresses to be
valid to this host.
- maxseg did not allow setting on an assoc basis. We needed
to thus track and use an association value instead of a inp value.
- Fixed ep get of HB status to report back properly.
- use settings flag to tell if assoc level hb is on off not
the timer.. since the timer may still run if unconf address
are present.
- check for crazy ENABLE/DISABLE conditions.
- set and get of pmtud (fixed path mtu) not always taking into account ovh.
- Getting PMTU info on stcb only needs to return PMTUD_ENABLED if
any net is doing PMTU discovery.
- Panic or warning fixed to not do so when a valid ip frag is
taking place.
- sndrcvinfo appearing in both inp and stcb was full size, instead
of the non-pad version. This saves about 92 bytes from each struct
by carefully converting to use the smaller version.
- one-2-one model get(maxseg) would always get ep value, never the
tcb's value.
- The delayed ack time could be under a tick, this fixes so
it bounds it to at least 1 tick for platforms whos tick
is more than a ms.
- Fragment interleave level set to wrong default value.
- Fragment interleave could not set level 0.
- Defered stream reset was broken due to a guard check and ntohl issue.
- Found two lock order reversals and fixed.
- Tighten up address checking, if the user gives an address the sa_len
had better be set properly.
- Get asoc by assoc-id would return a locked tcb when it was asked
not to if the tcb was in the restart hash.
- sysctl to dig down and get more association details
Reviewed by: gnn
- Fixed RTOinfo for bounding.
- Fixed connect() to return ECONNREFUSED when an ABORT is received.
- Added comments to direct Static Analysis not to look at some things
it does not understand (comments are /* sa_ignore XXXXX */)
- Bind when colliding was broken, missing not_found = 1 before
checking to see if the port was in use caused endless bind loop.
- Cookie life needs to be in milliseconds to conform to socket api.
- Cookie life is not supposed to change if its 0, On the assoc
level set we changed it to 0 opps.
- Two more static analysis issues identified by the cisco
tool. Null checks needed.
- An issue for sendfile(). Need to validate the correct
input argument.
- When sending failed due to a no route to host, we leaked
the mbuf chain failing to call m_freem().
- Fix #ifdef issue for getting hash block len when HAVE_SHA2 is NOT defined
Reviewed by: gnn
- PR-SCTP would ignore FWD-TSN's above a rwnd's worth
of TSN's (1 byte msgs).. this left the peer hopelessly
out of sync.. or an attacker. So now we abort the assoc.
- New IFN hash, also rename hashes to match addr/ifn now
that the vrf has multiple.
- Do not enable SCTP_PCB_FLAGS_RECVDATAIOEVNT per default
as defined in the Socket API ID.
- Export MTU information via sysctl.
- Vrf's need table id's. This is default for
BSD, but may be other things later when BSD
fully supports VRFs.
- Additional stream reset bug (caught by cisco dev-test).
- Additional validations for the address in sending a message (socket api).
-------- and -----
- Fix association notifications not to give the active open
side false notifications.
- Fix so sendfile and SENDALL will work properly (missing
flag to say socket sender is done).
- Fix Bug that prevented COOKIES from being retransmitted.
- Break out connectx into helper sub-models so that iox routines can
reuse the helpers.
- When an address is added during system init (non-dynamic mode) make
sure that the "defer use" flag is not set.
** its compiling on XR now :-D **
Reviewed by: gnn
set/clear it but would not do it. Now we will.
- Moved to latest socket api for extended sndrcv info struct.
- Moved to support all new levels of fragment interleave (0-2).
- Codenomicon security test updates - length checks and such.
- Bug in stream reset (2 actually).
- setpeerprimary could unlock a null pointer, fixed.
- Added a flag in the pcb so netstat can see if we are listening easier.
Obtained from: (some of the Listen changes from Weongyo Jeong)
set/clear it but would not do it. Now we will.
- Moved to latest socket api for extended sndrcv info struct.
- Moved to support all new levels of fragment interleave.
- moved away from ifn/ifa access to sctp_ifa/sctp_ifn
built and managed by the add-ip code.
- cleaned up add-ip code to use the iterator
- made iterator be a thread, which enables auto-asconf now.
- rewrote and cleaned up source address selection (also
made it use new structures).
- Fixed a couple of memory leaks.
- DACK now settable as to how many packets to delay as
well as time.
- connectx() to latest socket API, new associd arg.
- Fixed issue with revoking and loosing potential to
send when we inflate the flight size. We now inflate
the cwnd too and deflate it later when the revoked
chunk is sent or acked.
- Got rid of some temp debug code
- src addr selection moved to a common file (sctp_output.c)
- Support for simple VRF's (we have support for multi-vfr
via compile switch that is scrubbed from BSD but we won't
need multi-vrf until we first get VRF :-D)
- Rest of mib work for address information now done
- Limit number of addresses in INIT/INIT-ACK to
a #def (30).
Reviewed by: gnn
work is not just mine, but it is also the works of Peter Lei
and Michael Tuexen. They both are my two key other developers
working on the project.. and they need ata-boy's too:
****
peterlei@cisco.comtuexen@fh-muenster.de
****
I did do a make sysent which updated the
syscall's and sysproto.. I hope that is correct... without
it you don't build since we have new syscalls for SCTP :-0
So go out and look at the NOTES, add
option SCTP (make sure inet and inet6 are present too)
and play with SCTP.
I will see about comitting some test tools I have after I
figure out where I should place them. I also have a
lib (libsctp.a) that adds some of the missing socketapi
functions that I need to put into lib's.. I will talk
to George about this :-)
There may still be some 64 bit issues in here, none of
us have a 64 bit processor to test with yet.. Michael
may have a MAC but thats another beast too..
If you have a mac and want to use SCTP contact Michael
he maintains a web site with a loadable module with
this code :-)
Reviewed by: gnn
Approved by: gnn
